Linudix LMT-3000S Wireless POS Terminal User Manual General Warning Matter

Download:
Mirror Download [FCC.gov]
Document ID	496096
Application ID	jIpGoPPgyvrQfmzLuC5cBw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	93.21kB (1165096 bits)
Date Submitted	2004-12-13 00:00:00
Date Available	2004-12-10 00:00:00
Creation Date	2004-12-02 11:47:16
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-12-02 11:47:37
Document Title	General Warning Matter
Document Creator	Acrobat PDFMaker 5.0 for Word
Document Author:	???

LMT-3000S Installation Guide
2004-12-02
page. 1/1
LMT-3000S
Installation Guide
LMT-3000S Installation Guide
2004-12-02
page. 2/2
Revision History
2002. 12.24
Revision 1.0 is created.
2004. 10.12
Revision 1.1 is updated
2004. 12.01
Revision 1.2 is updated (Product specification is added.)
Document Title: LMT-3000S Installation Guide, Revision 1.2
Copyright © 2003 Linudix, Co. Ltd.
All rights reserved.
No part of this publication may be copied, distributed, stored in a retrieval system,
translated into any human or computer language, transmitted, in any form or by any
means, without the prior written consent of Linudix.
Comments or suggestions on how to improve this document can be
sent to possupport@linudix.com.
LMT-3000S Installation Guide
2004-12-02
page. 3/3
FCC WARNING
Note : This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use the
shielded signal cord supplied with this unit.
The Federal Communications Commission warns that changes or modifications of
the unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC RF EXPOSURE COMPLIANCE
This device has been tested for FCC RF exposure and SAR compliance in the host
hand-held, hand-operated electronic organizer/PC. To maintain FCC RF exposure
compliance, a 1.5 cm of separation distance must be maintained between the front
and back of the device and the user’s or any bystander’s body (excluding hands,
wrist, feet and ankles).
LMT-3000S Installation Guide
2004-12-02
page. 4/4
Table of Contents
GENERAL WARNING MATTER
A POWER RELATED WARNING MATTER
INSTALL THE LMT-3000S
STEP 1: UNPACK AND CONFIRM COMPONENT
STEP 2: INSTALL A PAPER ROLL IN THE PRINTER
STEP 3: INSTALL/REPLACE SIM CARDS
STEP 4: USE THE PRIMARY SMART CARD READER
STEP 5: USE THE MAGNETIC CARD READER
CLEAN THE TERMINAL AND PRINTER
10
TERMINAL
10
SMART CARD READER
10
PRINTER
10
TROUBLESHOOTING
11
PRODUCT SPECIFICATIONS
12
DESCRIPTION AND MODEL NAME
12
MAIN CONTROLLER SPECIFICATION
12
PERIPHERAL SPECIFICATION
12
CHARGER
13
SDK SPECIFICATION
13
OVERALL SPECIFICATION
14
APPEARANCE
14
LINUDIX SERVICE AND SUPPORT
15
LMT-3000S Installation Guide
2004-12-02
page. 5/5
General Warning Matter
When you use this product after purchase for the first time, let charge to the
full a battery and use it. The battery is not charged to the full, when the
product is shipment.
You are careful not to be wet to moisture this product. Fatal damage can
occur in it.
Please do not use this in high temperature and moisture environment.
Please do not use this in an explosive or a combustibility gas.
Please do not wipe the main body with gasoline or thinner and the same
chemical solution.
Please do not remodel or disassembles this product voluntarily.
Please do not keep a battery to firearms adjacency.
A Power Related Warning Matter
Please do not use damaged power cord, plug, and socket.
Please do not touch a power plug in a wet hand.
Please do a warning so that a power cord is not pressed by a heavy thing or
not stooped forcibly.
Please certainly use only a designated battery.
Please be careful so that it is not connected each other directly monads in the
outside of a battery or a battery charger.
Please do not give a severe shock to a battery charger or a battery, and do not
drop them.
LMT-3000S Installation Guide
2004-12-02
page. 6/6
Install the LMT-3000S
Step 1: Unpack and Confirm Component
Open the shipping carton and carefully inspect its contents for possible
tampering or shipping damage. If a component appears damaged, please
immediately notify the shipping company and your Linudix distributor or
service provider.
Please confirm whether there are the product main body and a component like
the following picture.
Printer Paper
Power adapter
Main body
Headset
Battery
Figure 1. LMT-3000S Product Component
Step 2: Install a Paper Roll in the Printer
A printer paper is provided with a
cylindricality of a diameter of 3cm.
If you above raise an opening thing button
located in the top of the terminal main
body, a printer cover opens.
LMT-3000S Installation Guide
2004-12-02
page. 7/7
Please turn over one side of a paper
mounting part in state above to have
completely opened a printer cover a
little, and please insert a paper.
Please be closed till
sound passes a printer
cover in state to have
pulled an edge of a
paper a little.
When print cuts a finished later printer paper, if you take a paper as a hand
and pull bottom course, you can cut a paper soft.
Step 3: Install/Replace SIM Cards
To unlock a cardholder, slide its locking
plate to the unlocked position, shown by
the OPEN arrow.
Open the cardholder by pivoting the cover
from its connector base.
Remove any previously-installed MSAM
card by sliding the card from the cover.
Install an MSAM card by aligning the card
and carefully sliding it within the guides on
the cover until fully inserted.
Note: The cardholder connector base has a set of
contacts and a notch post on one corner to ensure
the SIM card is positioned correctly when the
cover is closed. The SIM card has a notch on one
corner to ensure it fits into the connector
LMT-3000S Installation Guide
2004-12-02
page. 8/8
Figure 2. Using a SIM & SAM Card Holder
Step 4: Use the Primary Smart Card Reader
To conduct a transaction, position a smart card and insert it into the smart
card reader slot in a smooth, continuous motion until it seats firmly with a
“click”
Caution: Leave the smart card in the card reader until the transaction is
completed. Premature removal will invalidate the transaction.
When the display indicates the transaction is completed, remove the card.
Figure 3. Using the Primary Smart Card Reader
LMT-3000S Installation Guide
2004-12-02
page. 9/9
Step 5: Use the Magnetic Card Reader
To conduct a transaction, position a magnetic card and swipe it through the
magnetic card reader, as shown in following figure.
Figure 3. Using the Magnetic Card Reader
LMT-3000S Installation Guide
2004-12-02
page. 10/10
Clean the Terminal and Printer
Terminal
For dirt, use a clean cloth dampened with water and mild soap. For stubborn
stains, use alcohol or an alcohol-based cleaner.
Caution: Never use thinner, trichloroethylene, or ketone based solvents - they
may deteriorate plastic or rubber parts. Do not spray cleaners or other solutions
directly onto the keypad or display.
Smart Card Reader
Caution: Do not attempt to clean the smart card reader. Doing so may
invalidate your warranty. For smart card reader service, contact your Linudix
distributor or service provider.
Printer
Every few months, check and thoroughly clean the printer:
Be sure the terminal is connected to a power source.
Remove the paper roll cover and check it for signs of damage, wear, or
warping.
Remove the paper.
Remove any dirt, dust, or scraps of paper adhering to or lodged in the printer
parts.
LMT-3000S Installation Guide
2004-12-02
page. 11/11
Troubleshooting
An abnormal action
The expectation cause
A measure article
If a screen is not turned
A battery voltage is bad
Please retry after charging a battery.
on, even if a power key
A battery contact is bad
Please Check a battery installation state.
is pressed,
A battery is bad
It is exchanged with a new battery.
If a screen abnormally
Screen luminosity setting is
A screen being bright in a special function re-
looks
bad
setting.
A LCD indication device is bad
An A/S request.
It taking a paper
Please Check whether a paper is equipped a
If print is not successful
regular position with.
Printer roller is bad
Please Check whether a printer roller is normally
equipped.
Print density setting is bad
Re-setting please do print density in a special
function.
Printer is bad
An A/S request.
A card insertion error.
A card decoding direction check
Bad card use.
A card state (scratched, bending, filth)
A card reader is bad.
An A/S request
That a buzzer sound is not
Please check buzzer sound setting in a special
used is set up
function
Buzzer is bad
An A/S request
If telephone access
A base station communication
Please play a retry in other area.
does not become
fail
If a card is not read
If a buzzer does not ring
A mobile communication
check
Please play a retry soon.
accessed increase
Modem accessed inferiority
An A/s request
If a voice call function
A headset accessed abnormal
Please play a headset connection status check
does not work
Headset is bad
Other headset is used, and please talk on the
A call device is abnormal
phone
An A/S request
If it does not work to
Charging jack contact is bad
Charging jack and a power connection state
charge well
A charger / battery is bad
check
An A/S request
LMT-3000S Installation Guide
2004-12-02
page. 12/12
Product Specifications
Description and Model name
Description
Model name
Construction of PCB
: Wireless CAT
: LMT-3000S
: Main PCB / Key & LCD PCB
SIM & SAM PCB / IC card PCB
Main controller specification
CPU
' Part name
' Description
: Samsung S3C44B0X
: 66MHz ARM7TDMI RISC microprocessor
Memory
' Flash memory
' SDRAM
' SRAM
: 4Mbytes NOR flash
: 16Mbytes
: 128kbytes, Back up by lithium rechargeable battery
S/W
' O/S
: Embedded Linux installed on Flash memory
' Loader
: Installed
ETC
' Printer driver
' Buzzer
: High current driver
: Key beep
Peripheral specification
Modem
' Type :
' SIM
GSM(GPRS)
Sony Ericsson GR48 (850/1900MHz), FCCID: PY76220511
1 SIM(UIM) socket at behind of battery pack
Antenna Specification
' Frequency Range: 824~849MHz / 1850~1920MHz (Dual Band)
' VSWR : Less than 1.5:1
' Gain : 1.0 dBi
' Impedance : 50 Ohm
' Polarization : Vertical
' Radiation Pattern : Omni-directional
LCD
' Description
' Aux. function
MSR
' Description
: 128 * 64 pixels graphic type
: Digitally controlled contrast
EL back light
: Can read Track 1 & 2 simultaneously
Read magnetic stripe card at both direction
LMT-3000S Installation Guide
2004-12-02
page. 13/13
IC card interface
' I.F.M
: EMV Level 1 Certified Certification
' SAM
: 3 SAM socket at behind of battery pack
Printer
' Description
Comm port
' Description
: Thermal printer
60mm paper width, 48mm print width
200dpi resolution
: TTL level UART 1 port
(RS-232C level is optional)
for S/W upgrade, test & etc
Battery
' Description
' Capacity
' Nominal voltage
' Operating temp.
' Dimension
' Color
' Weight
: Lithium ion polymer battery
: 1850mAh nominal
: 3.7V
: Standard charge
: 0 ~ 45℃
Standard discharge
: -20 ~ 60℃
: 98 x 62 x 10 (L x D x H mm)
: Gray
: Max 60g
Charger
' Description
' Input voltage
' Charging method
' Charging voltage
' Output current
' Status LED
' Dimension
' Color
' Weight
: Charger for Lithium ion polymer battery pack
: AC 110V ~ 240V 50/60Hz (Min95V/Max264V)
: CC-CV mode
: DC 4.10 ~ 4.25V
: Normal 1.0A(Peak 1.5A, less than 5 min)
: Power on
: Green LED on
Charging
: Amber LED on
Battery disconnected
: Green LED on
After charging
: Amber ->Green LED on
Power off
: LED off
: 81 x 48.5 x 31.5 (L x D x H mm)
: Black
: Max 90g
SDK specification
Prepared Libraries
' Handling peripheral devices(MSR, Printer, etc)
' PC/SC library(Handling IFM)
' Handling GUI, MENU
' Glibc compatible library
Tools
' Compile Environment : Linux or Windows(Cygwin environment)
' Compiler : GCC
' Menu Generator
LMT-3000S Installation Guide
2004-12-02
page. 14/14
' Simulator
Overall specification
Packaging
' Contained item : LMT-3000S body
Battery pack
Charger(with PLUG Converter)
' Inner case
: Semi-formed plastic
' Outer Box
: Reinforced paper box
Operating temperature.
' Recommended
' Operable
' Relative humidity
: 0 ~ 50℃
: -10~60℃(Tested at each side about 30min)
: 5% ~ 95%, no condensing
Outline dimensions
' Size
: 178 x 80 x 43 (L x D x H mm)
' Weight
: Max 350g(with battery)
Certifications
' EMV Level 1 Certified
' EMV Level 2 Certified
' IECEE/CB (IEC 60950/EN 60950) Scheme Certified (Safety)
' FCC Part15B, Part22/24
Appearance
LMT-3000S body
Battery & Charger
LMT-3000S Installation Guide
2004-12-02
page. 15/15
Linudix Service and Support
For LMT-3000S terminal problems, contact your local Linudix representative
or service provider.
For LMT-3000S product service and repair information:
• http://www.linudix.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2004:12:02 11:47:37-08:00
Create Date                     : 2004:12:02 11:47:16-08:00
Page Count                      : 15
Creation Date                   : 2004:12:02 19:47:16Z
Mod Date                        : 2004:12:02 19:47:16Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : ???
Metadata Date                   : 2004:12:02 19:47:16Z
Creator                         : ???
Title                           : General Warning Matter
Page Mode                       : UseNone
Tagged PDF                      : Yes

EXIF Metadata provided by EXIF.tools