Lionda Technology Co M46001 900 MHz 40 Channel Cordless Phone with CID & DAM User Manual FCC Information and End

Download:
Mirror Download [FCC.gov]
Document ID	138451
Application ID	28lR6Ett9uLBuiehDwMvLw==
Document Description	FCC Information and End
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	253.4kB (3167477 bits)
Date Submitted	2001-02-28 00:00:00
Date Available	2001-02-28 00:00:00
Creation Date	2001-02-05 11:41:14
Producing Software	Acrobat 3.0 Scan Plug-in
Document Lastmod	2001-02-05 11:41:55
Document Title	FCC Information and End
Document Creator	Acrobat 3.0 Scan Plug-in

3. Begin speaking immediately after you hear, “ lease record your message
after the beep.'Continue to depress the button. One second
after completing your Memo, release the button and you will
hear, "End of Recording, " Your recorded Memo will be played thereon.
Day and time are automatically stamped at the end of the message.
NOTE: The Answering System advances the message count automatically
after the actual message is recorded.
NOTE: To obtain a better sound ' duality for locally recorded (OGMs and
Memos) messages, speak directly into the MICROPHONE from a
distance of 9 to 12 inches.
MA DIST ,
or 9 T0012 W CHEQNgE
MICROPHONE A
Playing of Messages/Memos
A. To play messages/memos in the PRIMARY MAILBOX.
1. Press the button. the system will play all NEW messages/memos.
2. After playing all NEW messages/memos. press the @ button again,
the system will play all of its messages.
B. To play messages/memos in an individual MAILBOX (1, 2, 3, 4).
1. Press a mailbox button. the corresponding MAILBOX LED indicator
starts to blink.
2. Press the button. The system will play all NEW messages/memos.
3. After playing all NEW messages/memos. press the button again,
the system will play all of its messages/memos.
NOTE: When MAILBOX LED indicators are lit, messages are present.
C. To interrupt a message.
1. Press the button once while playing a message, ”FF" will be
displayed.
2. Press the button to continue playing the message where you
stopped.
3. Press the @ button twice to end the playing of message
D. To repeat a message/memo.
1. Press the button while playing a message. The system
repeats the current message in its entirety
Answering System Operation
E. To skip message/memo.
1. Press the button once. The Answering System stops playing.
moves to the next message/memo and resumes playback. The system
advances one message/memo each time you press the button.
F. To play a previous message/memo.
1. Press the button twice quickly.
Saving Messages
The Answering System saves your messages automatically. After playing all of your
messages, the Answering System announces. "End of messages' and the total number
of messages stored in the memory will be indicated by the LED Message Display
NOTE: The Answering System has a total Memory capacity of 12 minutes or up
to 63 messages (OGM/ICMIMEMO). If the recorded messages contain
high background noise. the total recording capacity of the unit will be less
than 12 minutes.
Erasing Messages
A. To erase all of the messages i the PRIMARY MAILBOX
1. Press and hold down the button until you hear the ANNC
“Messages erased." If you have a new message in the PRIMARY
MAILBOX, you will hear. “You have # new messages."
B. To erase all of the messages in an individual MAlLBOX (1, z, 3, 4)
1. If you want to erase all of the messages in a mailbox. activate the
desired mailbox.
2. Press and hold down the «erase button until you hear the ANNC,
“Messages erased, Mailbox #. You have no messages." If you have a
new message in the MAILBOX #, you will hear, “You have # new messages.”
C. To erase selected messages/memos
1. While the unwanted message is playing, press the button. The
Answering System announces erasure of the selected message/memo,
and the LED Message Display shows the symbol of “ER.” After the
Erasure is complete. the numeric order of the remaining messages will
be rearranged.
When the Memory is Full
When there is no memory available for additional messages, the Answering System
will announce. “Memory full,” but will not save messages. While the Memory is full
you can access your messages on the Answering System via remote control.
NOTE: You must enter your Remote Access Code within 10 seconds of activat-
ing the remote control function to maintain your connection with the
Answering System. (Refer to Remote Control Operation on page 38.)
a‘
at.
Answering System Operation
Remote Control Operation
The Answering System can be operated through the HANDSET or away from
your home through a Touchtone telephone.
Remote Operation through the HANDSET
You can operate your Answering System via remote control using the
HANDSET.
1. Press the @ button at theSTANDBY mode, to activate the remote
control function. "
2. Press the corresponding number of the function you wish to activate.
A. Press “2" to play messages.
B. While playing messages. press “1" to repeat or “3” to skip.
o. Press ”4" to stop playing messages and go to the PRIMARY MAILBOX.
. Press "5" to play your OGM.
Press “7” to record your OGM.
F“
Press “6" to record memo messages.
Press “4‘” to stop recording or after your memo is completed.
Press “9" to erase messages being played.
. Press “8" to activate or deactivate the answering function.
. Press “*" to activate the remote operation of MAILBOX 1.
Press “0” to activate the remote operation of MAILBOX 2.
Press “#" to activate the remote operation of MAlLBOX 3.
. Press “tone" to activate the remote operation of MAILBOX 4
RPrIOT“
NOTE: After the remote control function is activated. Instruction Code must be
entered within 10 seconds. It not, the HANDSET will terminate the
remote control operation.
3. Press the flint button to deactivate the remote control function or place
the HANDSET on the BASE UNIT.
Using the Remote Instruction Code
1.
2.
3.
Dial your telephone number.
Listen to or bypass the OGM in the PRIMARY MAILBOX.
Enter your Remote Access Code. If the announcement does not stop, enter
the Remote Access Code again,
The Answering System will request that you enter the Instruction Code or
press “0” for help.
A. If you do not know the Instruction Code, press “0" immediately. The
Answering System will announce the Instruction Codes. Otherwise, it a
command is not received by the Answering System within 10 seconds, it
will signal 3 “beeps" and hang up
The following is the Remote Instruction Code Help Menu:
Instruction Codes
To playback Announcement Press “Sf
To Record Memo Press “6.“ (Press “1" for MAILBOX 1, Press “2" for
MAILBOX 2. Press “3" for MAILBOX 3. and Press “4" for MAILEOX 4.
Otherwise. if you do not press the desired MAILBOX# location within
2-3 seconds, the memo will be automatically recorded in the
PRIMARY MAILBOX.)
To Record Announcement Press “7."
To Tum Answering Machine On or Off Press “8."
To Change Mailbox Press “*.'
To Playback Message Press “2 "
While message playback
To Repeat Message Press “1."
To Skip Message Press "3."
To Stop Press “4.“
To Erase Message Press “9.“
B. Press the corresponding number of the Instruction Code you wish to
activate. You don't have to listen to the entire Instruction Code Help Menu
before giving a command. You may enter the desired Instruction Code
Number at any given time.
Answering System Operation
Remote Operation through 3 Tone Telephone
You can use many Answering System features when you are away from home.
To protect your privacy, most of the features can be used only after you enter the
three-digit Remote Access Code.
Remote Access Codes
The Remote Access Codes are preset at the factory as shown below You can
use the preset codes or choose your own,
PRIMARY MAILBOX: 999
MAILBOX 1: 555
MAILBOX 2: 665
MAILBOX 3: 777
MAILBOX 4: 888
NOTE: If the weset button is pressed, the Remote access Codes return to the
factory preset codes,
Changing of the Remote Access Codes
All of the digits of the Remote Access Codes are a combination of numbers 5. 6,
7. 8, 9, Dr
lMPORTANT: Digits 1, 2, 3, and 4 cannot be used when changing the Remote
Access Codes for any mailbox (including the PRIMARY MAILBOX),
1. Press a mailbox button for MAlLBOX 1, 2, 3, or 4. For the PRIMARY
MAILBOX, follow steps 2 to 6.
2. Press and hold down the codé’ button until you hear the ANNC,
“Please enter new password ”
3. Press and hold down the day button. Release the button when you
hear the desired first digit of the code.
4. Press and hold down the button. Release the button when you
hear the desired second digit of the code.
5. Press and hold down the minute button. Release the button when
you hear the desired third digit of the code,
6. Press the code button, the 3-digits you have selected will be
announced.
7. if your new Remote Access Code is the same as that of another mailbox,
you will hear, “Please try again."
Tl
l.
Security
Security _
Your cordless telephone uses a digital coding security system to prevent
unauthorized use of your telephone line by another nearby cordless telephone.
The system has its own identifying signal created by microcomputers in both
the BASE UNIT and HANDSET.
Security Code
This telephone has an internal security code with 65,536 possible combinations.
Resetting Security Code and Channel Information
Communication between HANDSET and BASE UNlT may not be possible in
any of the following situations:
1c After a power failure.
2. After relocating the BASE UNIT by disconnecting the AC ADAPTOR.
3. After replacing the HANDSET BATTERY PACK.
To reset, place the HANDSET on the BASE UNIT for more than 2 seconds.
Multi-Channel Access
Your cordless telephone lets you select a channel from the 40 frequencies
available to transmit signals between the BASE UNIT and HANDSET. When
you notice interference from other cordless telephones. change to another
channel by pressing the button on the HANDSET.
"VIPORTANT
When you hear interference, press the m
button to change the operating channel.
Battery Type
Use the following type and size of BATTERY PACK:
Cordless Telephone BATTERY PACK
3.6V, SOOmAh
U.S. Electronics Inc.
Ni-Cd BATTERY PACK: model 8650 NiACd
This BATTERY PACK is available through:
us Electronics Service Center
105 Madison Avenue ‘
New York, NY 10016
1—800-828-5208
Recharging the BATTERYPACK
The nickel cadmium (Ni-Cd) BATTERY PACKin the HANDSET can be recharged
many times using the built-in charger in the BASE UNIT.
When the BATT LOW symbol appears on the LCD screen. a “beep" sound will
be heard every 10 seconds. This indicates that the BATTERY PACK needs to
be recharged.
Charge the BATTERY PACK at least once every 90 days of non-use to avoid
battery failure, When the BATTERY PACK can no longer be charged.
replacement of the BATTERY PACK will be necessary.
The BATTERY PACK used in your telephone may develop a condition known
as “MEMORY". Once subjected to a regular short discharging routine, the
BATTERY PACK assumes the discharging pattern it was subjected to. This is
known as a “MEMORY" condition which causes rapid discharging thereby
shortening the BATTERY PACK charge span. If you believe your BATTERY
PACK has developed a “MEMORY‘ condition, do not charge the HANDSET
until the BATT LOW symbol appears on the LCD screen. When the BATT
LOW symbol appears on the LCD screen. charge the HANDSET fully for 12
hours.
IMPORTANT
in order to giet maximum life from the HANDSEI'
BATTERY PACK, be sure to charge the HANDSET‘
for§12 hours before initial use.
Changing the BATTERY PACK
Changing the BATTERY PA CK
The BATTERY PACK provides power for the HANDSET of your cordless
telephone
To Replace the BATTERY PACK:
2.
3.
4.
5.
.Remove the HANDSET BATTERY COMPARTMENT COVER by sliding it
down.
Pull out the BATTERY PACK PLUG and remove the BATTERY PACK.
Plug the new BATTERY PACK into the BATTERY CONNECTOR.
Slide the HANDSET BATTERY COMPARTMENT COVER firmly into place
in its closed position.
Before use. charge the new BATTERY PACK for 12 hours,
ATTENTION:
The telephone that you have purchased contains a rechargeable BATTERY PACK.
The BATTERY PACK is recyclable, At the end of its useful life, under various
state and local laws. it may be illegal to dispose of this BATTERY PACK into the
municipal waste stream. Check with your local solid waste officials for details in
your area for recycling options or proper disposal,
,, _. ,_ , l
fen-mm HATDSEBATTERV
WARD/ENTOOVERbysliing'ndom
Problem Solving
Problem Solving Section
For your assistance, we have listed below a few common problems,
Phone does not work, check the following.
1. BASE UNIT is plugged into power source.
2 HANDSET is charged.
3. TONE/PULSE Select Switch' is in the right position.
4. TELEPHONE LINE CORD is Plugged into the TELEPHONE JACK.
Range of phone limited, check the following:
1. ANTENNA on BASE UNIT is raised.
2. BASE UNIT is centrally located in your residence.
3. BASE UNIT is not located near appliances.
No dial tone, check the following:
1. TELEPHONE LINE CORD plugs are connected to the TELEPHONE JACK
and TELEPHONE LINE CONNECTION JACK.
2. BASE UNIT is plugged into power source.
3. If you had a power failure or had unplugged the BASE UNIT, replace the
HANDSET on the BASE UNIT for 2 to 5 seconds to reset the system.
Received signal flutters or fades, check the following:
1. BATTERY PACK in the HANDSET is fully charged.
2. HANDSET is not too far from the BASE UNIT.
3. ANTENNA on the BASE UNlT is raised.
Interference on reception, check the following:
1. Noise may be picked up from electrical products in the home or electrical
storms. Generally, this noise is a minor annoyance and should not be inter-
preted as a defect in your system. (See Tech ‘cal lniormation on page 46).
2. Choose an alternate channel using the - button on the HANDSET.
Long Distance "L- D C” Indicator is not ON when receiving long distance
call, check the following:
1. Your local telephone company can provide the Area Code on an incoming
long distance call.
Excess static, check the following:
1. Check to see that the ANTENNA is not touching another metal object.
2. Raise or reposition the BASE UNIT ANTENNA.
If after pressing the talk button, you receive three beeps and no dial
tone, check the following:
1. BASE UNlT is plugged into power source.
2. If you had a power failure or had unplugged the BASE UNIT. replace the
HANDSET on the BASE UNIT for 2 to 5 seconds to reset the system.
Problem Solving
Answering System does not work, check the following:
1. BASE UNlT is plugged into power source.
2. Reset the system by pressing the RESET button at the side of the BASE
UNIT.
Answering System does not answer calls, check the following:
1. ANSWER ON/OFF LED indicator is lit.
Answers calls only after 10 rings, check the following:
1. ANSWER ON/OFF LED indicator is lit,
2. Message Memory is not full.
Does not respond to remote commands, ensure the following:
1. Correct Remote Access Code is entered.
2. A TONE telephone is being used.
Messages are incomplete, ensure the following:
1. Message Memory is not full.
2. Caller may be hesitating and pausing for more than 7 seconds.
Answers calls but does not record messages, check the following:
1. ANNCIICM switch is set to ICM.
2. Memory is not full.
3. Extension telephone was not picked up,
NOTE: If none of the telephones in the house are working, disconnect one set
at a time to verify that none of the lelephones are causing the problem. If you
still have a problem after doing this, and your telephone still does not work,
please contact your local phone company.
“Iii!
Technical Information
This cordless telephone uses radio frequencies to allow mobility. There are
certain difficulties in using radio frequencies with a cordless telephone. While
these are normal, the following could affect the operation of your system.
Noise
Electrical pulse noise is present in most homes at one time or another. This
noise is most intense during electrical storms. Certain kinds of electrical
equipment such as light dimmers,'fluorescent bulbs. motors, and fans also
generate noise pulses. Because radio frequencies are susceptible to these
noise pulses, you may occasionally hear them in your HANDSE’I‘. Generally
they are a minor annoyance and should not be interpreted as a defect in your
system,
Range
Because radio frequency is used, the location of the BASE UNIT can affect
the operating range. Try several locations in your home or office and pick the
one that gives you the clearest signal to the HANDSET.
Interference
Electronic circuits activate a relay to connect the cordless telephone to your
telephone line. These electronic circuits operate in the radio frequency
spectrum, While several protection circuits are used to prevent unwanted
signals, there may be periods when these unwanted signals enter the BASE
UNIT. You may hear clicks or hear the relay activate while you are not using
the HANDSET. If the interference occurs frequently, it can be minimized or
eliminated by lowering the height of your BASE UNIT ANTENNA or by
relocating the BASE UNIT. You can check for interference before selecting the
final BASE UNIT location by plugging in the phone.
NOTICE:
This cordless telephone uses radio communication between the HANDSET
and the BASE UNIT and may not ensure privacy of communication, Other
devices, including other cordless telephone, may interfere with the operation
of this cordless telephone or cause noise during operation. Units not
containing coded access may be accessed by other radio communication
systems. Cordless telephones must not cause interference to any licensed
radio service
FCC Requirements
Federal Communications Commission Requirements
This equipment complies with Part 68 of the FCC Rules, A label on the BASE
UNIT of this equipment contains, among other information, the FCC Registration
Number and the Ringer Equivalence Number (REN) for this equipment. You
must, upon request. provide this information to your telephone company.
The REN is also useful in determining the quantity of devices that you may
connect to your telephone line and still allow these devices to ring when your
telephone number is called. in most areas, but not all. the sum of the REN’s for
all devices connected to one line should not exceed five (5.0). To be certain of
the number of devices that you may connect to your line, you should contact
your local telephone company.
If your equipment should cause harm to the telephone network, the telephone
company may temporarily disconnect your service. If possible, they will notify
you in advance that temporary discontinuance of service may be required
However, when advanced written notice is not possible, the telephone company
may temporarily discontinue service without notice if such action is necessary
under the circumstances The telephone company may make changes in its
communication facilities, equipment, operations, or procedures where such
action is reasonably required in the operation of its business and is not
inconsistent with the rules and regulations of the Federal Communications
Commission. Do not attempt to repair or modify this equipment.
WARNING: Changes or modifications not expressly approved by the party
responsible for its compliance could void the user’s authority to operate the
equipment.
Some cordless telephones operate at frequencies that may cause interference
to nearby TVs and VCRs. To minimize or prevent such interference, the base of
the cordless telephone should not be placed on or near a TV or VCR. If
interference is experienced, moving the cordless telephone farther away from
the TV or VCR will often reduce or eliminate the interference.
This equipment should not be used on coin telephone lines. Connection to party
line service is subject to state tariffs. If trouble is experienced, disconnect this
equipment from the telephone line to determine if it is causing the malfunction.
If the equipment is determined to be malfunctioning. its use should be
disconnected until the problem has been corrected.
i l
‘lil
FCC Requirements
Federal Communications Commission Requirements (continuem
Note: This equipment has been tested and found to comply with the limits for
a class B digital device. pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However. there is no guarantee that interference will occur in a particular
installation. If this equipment does-cause harmful interference to radio or
television reception. which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
1. Reorient or relocate the receiving ANTENNA.
2. Increase the distance between the equipment and the receiver,
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radiolTV technician for help.
Warrantylnformation
BellSouth Products
One-Year Limited Warranty
This limited warranty sets forth all BeIlSouth Products responsibilities regarding
your product. There are no other expressed or implied warranties from BellSouth
Products.
Warranty Service Provided
If you purchased the telephone new from a retail vendor, BelISouth Products
warrants the telephone against defects in material and workmanship for a
period of one (1) year from the original date of purchase. This warranty is in
lieu of all other express warranties. This warranty begins when you purchasethe
telephone and continues for one (1) year unless you sell or rent the telephone.
in which case the warranty stops.
BellSouth Products disclaims any implied warranty, including the warranty of
merchantability and the warranty of fitness for a particular purpose. as of the
date of 90 days from your original purchase of the telephone, BeIlSouth
Products assumes no responsibility for any special, incidental. or consequential
damages.
This warranty gives you specific legal rights and you may have other rights which
vary from state to state. Some states do not allow the exclusion or limitations
of special, incidental or consequential damages. or limitations on how long a
warranty lasts. so the above exclusion and limitation may not apply to you.
Warranty Service Not Provided
This warranty does not cover damage resulting from accident, misuse. abuse.
improper installation or operation. lack of reasonable care. unauthorized
modification, the affixing of any attachment not provided by BeIlSouth
Products with the telephone and/or loss of parts. This warranty is voided in the
event any unauthorized person opens, alters or repairs the telephone. All
BellSouth equipment being returned for repair must be suitably packaged,
Telephone companies use different types of equipment and offer various types
of services to customers. BelISouth Products does not warrant that this
telephone is compatible with the type of equipment of any particular telephone
company or the services provided by it.
at.
What to Do for Warranty Service
During the first thirty (30) days. a defective product is eligible for over-the-
counter exchange at the retailer from whom it was purchased. After thirty (30)
days. the defective product should be returned to the authorized service center.
Please allow 2-3 weeks for the return of your telephone product. The shipping
address of the authorized service center is:
U.S. Electronics CONSUMER CENTER
CIO Southern Bonded Warehouse
1491 Mt. Zion rd. .-
Morrow. GA 30260
NOTE: A product received which was not made for BellSouth Products or
which is not defective as determined by our test procedures will not be repaired
and will be retumed CAO.D , freight,
To Obtain Warranty Service
- Provide proof of the date of purchase within the package
- Prepay all shipping costs to the authorized service center,
- Include a return shipping address within the package.
Please retain your sales receipt. the carton, the packing materials, and the
printed material. The original carton is the best shipping container for the
telephone should you have to return it.
For your reference:
Serial number ________—
Date of Purchase _____—____
Name of Dealer
Customer Service Telephone Number:
1-800-210-8950
OUTSIDE THE USA. CALL 1-212-242-6978
This page serves as a template for attachment of screws to
the wall when mounting this telephone on the wall.
1. Cut out this page.
2. Use this template to determine the distance between
screws when mounting this phone on the wall.
The two cross hairs identify where to attach the
screws.
lMPORTANT
In order to get maximum life from the HANDSET
battery pack, be sure to charge the HANDSET
for 12 hoursbefore initial use.
IMPORTANT
Placing your BASiE UNIT near appliances
such as televisions, refrigerators, radios, or
microwave ovens may cause interference.
IMEORTANT
“k
When you hear int erence, press the m
button to changeéthe operating channel.
IMPQRTANT
The Ac ADAPTOKmust always be plugged
into an electrical outlet.
IMPQRTANT
To obtain the bait reception, he sure to
raise or repositinnllle BASE UNIT ANTENNA.
g,
IMPQRTANT
if you live in an area which gets frequent
thunderstorms, we strongly recommend plugging
your Ac ADAPTOB into a surge protector.
Make certain you receive the best
performance from your telephone.
Read this manual first.
@ BELLSOU TH
MH9934A Made m chm

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:02:05 11:41:55+08:00
Create Date                     : 2001:02:05 11:41:14+08:00
Creator                         : Acrobat 3.0 Scan Plug-in
Producer                        : Acrobat 3.0 Scan Plug-in
Page Count                      : 19

EXIF Metadata provided by EXIF.tools