Lodar 103 103-16 User Manual TI 103RX 01E

Lodar LTD 103-16 TI 103RX 01E

Contents

User Instructions

2or Disconnect BatteryIDENTIFY POWERCONNECTION POINTAND ISOLATE SUPPLYFuseRemove fuseVehicle batteries contain gasses which are flammable and explosive. Wear eye protection and do not lean over battery while disconnecting. Do not wear metal jewellery.!WARNINGTI-103RX.01E1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5 Amps each through 3 outputs.2. Master Output. This can be configured to Continuous or Parallel operation, see below right for more details.3. If Receiver outputs are connected in parallel with an external switching device (wired remote) the Receiver will instantly switch off when the wired remote is operated4. Lodar Receivers have an isolation switch for safety, to allow for registering a MUST replacement Transmitter.5. Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes of inactivity. This can be altered, ask your dealer.1!BEFORE YOU STARTWiring Instructions for TI-103 Series 1 to 16 Function, FET Receivers.3Secure using 5mm (3/16") bolts (not supplied)through the 4 mounting feetTAKE TIME TO LOCATE THE BEST POSITIONIf necessary, power the Receiver and move it aroundthe vehicle until the required performance is achieved.Operate the Transmitter and observe the Receiverinternal LED’s.Mount as HIGH as possibleAVOID surfaces with HEAVY VIBRATIONAVOID DIRECT SPRAY from wheelsIn a HOT CLIMATE fit in a SHADED positionCable gland should face DOWN or BACKReceiver 92 20 RX and 93 20 RX shown,CAUTIONMOUNT RECEIVER!What is the MASTER Output for ?It is used to operate the pump of an electro-hydraulic power pack or maybe a clutch pump. It can also be used for powering a dump valve, master valve etc. It can be configured to work continuously, that is ON when SET is pressed and OFF when STOP is pressed; or in parallel with any output, that is, it isactive only a function is operated. If it is needed with certain functions only, this can easily be configured.CONNECTION DETAIL5OPTIONAL AERIAL CONNECTIONENSURE THAT THE GAUGE OF WIRE USED CAN CARRY 15 AMPS (THIS IS THE MAXIMUM TOTAL CURRENT THAT LODAR CAN SWITCH)OVER THE DISTANCE FROM THE BATTERY WITH NO SIGNIFICANT VOLTS DROP!IMPORTANTThe Receiver switches itself offafter 30 minutes of inactivity.SAFETY FEATURE!NOTEThe STOP input can be used for OVERLOAD or OVER-TEMPERATUREetc. If the chassis isGROUND, then a returnwire is not required.!!IMPORTANT TAKE CARE NOT TO SHORT OUT THE MOSFET’s WHEN MAKING CONNECTIONS4
GROUND12 / 24 VOLT COMMONFUNCTION 5FUNCTION 6FUNCTION 7FUNCTION 8MASTERFUNCTION 1FUNCTION 2LK1FUNCTION 3FUNCTION 46Make connections as detailed belowand record wire colours in the boxesLK2LK1, when bridged causes the Master Output to be ParallelLK2, when bridged causes the Master Output to be ContinuousJUMPER MUST BE FITTED FOR LODAR TO WORKPOWER DOWN RECEIVER BEFORE MAKING CHANGESJUMPER may be or RED BLUESTOPConnectionsS+ (Safety Solenoid etc.)L1 = LIMIT 1L2 = LIMIT 2LIMIT INPUTSFUNCTION 9FUNCTION 10FUNCTION 15FUNCTION 16FUNCTION 17FUNCTION 18FUNCTION 11FUNCTION 12FUNCTION 13FUNCTION 14FUNCTION 19FUNCTION 20STOP0 VoltsGROUND7FINAL CHECK!ALL ITEMSIMPORTANTCheck all connector screws for tightnesseven the ones that are not used as these could cause a short circuitif they vibrate out of the connectorCheck locknutCheck glandCheck tightness of cable glandabStray strands of wire can cause a short circuitcdCONNECTORBLOCKPOsecure wireor Connect BatteryIT IS NOW SAFE TO RECONNECT THE POWER SUPPLYRefit fuseeFuseVehicle batteries contain gasses w h i c h a r e f l a m m a b l e a n d explosive. Wear eye protection and do not lean over battery while !WARNINGSPECIALORDERONLYTI-103RX.01E
Indicator LED’s 1 through 20Indicator LED - Master 5 Volts LEDSet LEDFault LEDLED’s indicate the followingLED marked “5V” indicates power supply for control circuits is OKLED marked “SET” indicates the system active.LED marked “Fault” indicates an overload is present; the system cannot be reset until overload is removed.This LED blinks for 20 seconds when the system is initially powered. A replacement Transmitter (or Keypad or Wired Remote) has to be registered during this 20 second period.LED’s marked F1 to F16 and M (and optional MC) when ON indicate an output to that function(MC is an extra Continuous Master output)COMPONENT DETAILLodar TI Series is guaranteed for a period of 24 months from the date of purchase, as long as it is wired in accordance with our instructions, and that the equipment is fitted with an isolation system to shut off all power in event of an emergency.Your product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.In the EEC - Please contact your National Distributor (see www.lodar.com for this information) who will inform you about the take-back of the product. You might be charged for the costs arising from the take-back and recycling. Small products might be taken back by your local collection facilities.Outside the EEC - If you wish to discard this product please contact your local authorities and ask for the correct method of disposalIPIPF1 F2F3 F4F5 F6F7 F8F9 F10F11 F12F13 F14F15 F16F17 F18F19 F20Numbering conventionof Transmitter Keypadshowing the Receiveroutput function numberfor that key.LIMITS - What are these?The new compact 20 function Receiver has an input for limit functions. The circuits between L1 andground (-) or L2 and ground,which when the circuit is made, or broken, will allow a function to start or causea function to stop. This requires special programming.We also have available anadd-on PCB, Part No. 9220that has a further 8 Limits.We have successfully used this feature on a number ofprojects to introduce a degree of logic using theon board Programmable ICor PIC. It may not be economical to program the Receiver PIC for a smallbatch, please ask.TI-103RX.01E
!1 2Function ButtonsRESET Button activates the Receiver and the keypadfunction buttons4 Release Screws forBattery Compartmentat rear.4 x AAA batteriesEffective working range up to a distance of60 metres (200 feet) 92 Series and300 metres (1000ft) 93 Series.The Transmitter automatically transmits a STOP signal after30 minutes; this de-activatesthe Receiver and the Transmitter.SAFETY FEATURE!To register Transmitters to the Receiver.Switch OFF or DISCONNECT the power to the Receiver and briefly PRESS the STOP button on one or both Transmitter(s).Switch ON or Reconnect the power to the Receiver.This opens a 20 second registration window in the Receiver processor. If you are looking at the Receiver PCB the Fault LED Flashes.Immediately PRESS and HOLD both the Transmitter RESET Button and F1 Button (indicated). Continue to hold BOTH BUTTONS for a MINIMUM of 5 seconds during this 20 second window.When the Transmitter is Registered the Fault LED will be illuminated for 3 seconds. Within this 3 second period, FIRST release F1 and then the RESET button.TO REGISTER TWO TRANSMITTERS: When the fault light starts to flash again, and immediately PRESS and HOLD both the Transmitter RESET F1 Buttons of the second Transmitter. Continue to hold BOTH BUTTONS for a MINIMUM of 5 seconds or until the SET LED comes on. Both your Transmitters will now operate the Receiver.PRIORITY.Only one Transmitter can be active at any time. For the second Transmitter to work you have to turn off the first Transmitter. Once the second Transmitter is being used then that has priority and it has to be turned off before the first Transmitter can work again.If you have any problems please phone either your local Distributor or Lodar directly:- UK +44 1922 613633. US 1-877- 257-1581.!PRESS & HOLD both RESET and F1for a MINIMUM of5 SECONDSInstructions for TI-103 Series IP Transmitters(16 Function shown)www.lodar.comSTOP Button switches off the Receiver and the keypad function buttonsL.E.D. Blinks when Transmitter is active.ON when a TransmitterButton is pressed.Pulses while transmittingwhen Battery is low.!TI-103RX.01E

Navigation menu