Lodar P03 Transmitter Standard-433 User Manual 1

Lodar LTD Transmitter Standard-433 1

Contents

User manual

Download: Lodar P03 Transmitter Standard-433 User Manual 1
Mirror Download [FCC.gov]Lodar P03 Transmitter Standard-433 User Manual 1
Document ID2363898
Application IDpnpKvKoxxAt/p7A+ehSM5A==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize238.95kB (2986920 bits)
Date Submitted2014-08-20 00:00:00
Date Available2014-08-20 00:00:00
Creation Date2014-01-17 09:58:24
Producing SoftwareCorel PDF Engine Version 16.0.0.707
Document Lastmod2014-05-22 10:15:38
Document TitleUntitled-1
Document CreatorCorelDRAW X6
Document Author: Martin

Wiring Instructions for 2 & 4 Function, 92 & 93 Series, FET Receivers.
1.
IDENTIFY POWER
CONNECTION POINT
AND ISOLATE SUPPLY
BEFORE YOU START
The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps
through one output or 5 Amps each through 3 outputs.
Fuse
2.
Master Output. This can be configured to Continuous or Parallel operation, see overleaf for
details.
3.
If Receiver outputs are connected in parallel with an external switching device (wired remote)
the Receiver will instantly switch off when the wired remote is operated
4.
Lodar Receivers MUST have an isolation switch for safety, to allow for registering a
replacement Transmitter.
5.
or Disconnect Battery
WARNING
Vehicle batteries contain gasses
which are flammable and explosive.
Wear eye protection and do not lean
over battery while disconnecting. Do
Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes of
inactivity. This can be altered, ask your dealer.
MOUNT RECEIVER
Remove fuse
POSITIVE
STOP
NEGATIVE
CAUTION
TAKE TIME TO LOCATE THE BEST POSITION
If necessary, power the Receiver and move it around
the vehicle until the required performance is achieved.
Operate the Transmitter and observe the Receiver
internal LED’s.
Mount as HIGH as possible
AVOID surfaces with HEAVY VIBRATION
AVOID DIRECT SPRAY from wheels
In a HOT CLIMATE fit in a SHADED position
Cable gland should face DOWN or BACK
92 00 RX
& 93 00 RX
have
4 core cable
Receiver 92 04 RX and 93 04 RX shown,
Waterproof to IP67, complete with 3 metres (10 ft) cables
92 02/4 RX
& 93 02/4 RX
have
7 core cable
Secure using 5mm (3/16") bolts (not supplied)
through the 4 mounting feet
What is the MASTER Output for ?
CONNECT
WIRES
9000
www.lodar.com
F1
F2
F3
F4
Transmitter
Function
Convention
Make notes about the
connections made
in the boxes below
9200RX
and 9300RX
9202RX
and 9302RX
Wire Colour
Wire used for
RED
12/24 Volts DC Nominal
Positive Supply
BLACK
Negative
GREEN
Output Function 1
YELLOW
Output Function 2
BROWN
Output Function 3
Not Present
Not Used
BLUE
Output Function 4
Not Present
Not Used
WHITE
Output Function Master Not Present
9204RX
and 9304RX
It is used to operate the pump of an electro-hydraulic
power pack or maybe a clutch pump. It can also be
used for powering a dump valve, master valve etc.
It can be configured to work continuously, that is ON
when SET is pressed and OFF when STOP is
pressed; or in parallel with any output, that is, it is
active only a function is operated. If it is needed with
certain functions only, this can easily be configured.
Replace fuse
Fuse
ACTIVATE THE
RECEIVER SUPPLY
or re-connect Battery
CONNECT TRANSMITTER BATTERY
Batteries generally have to be
disconnected when shipping.
TEST
Press the Transmitter RESET button
to activate the system, and carefully
test each function for correct operation.
92104.05 FET 24
LED marked “SET”
Component Detail
LED’s marked
“F1 - F2 - F3 - F4 and M”
When ON indicate an
output to that function
Indicates system
is active
LED marked “FAULT”
Indicates an overload is
present; the System
cannot be RESET until
overload is removed.
This LED blinks for 20
seconds when the
Receiver is initially
powered. A replacement
Transmitter has to be
registered during this 20
second period.
LED marked “5V”
VOLTAGE
Working Range
12 Volts to 36 Volts DC
Indicates power
supply for control
circuits is OK
Limits
8 Volts minimum to
40 Volts absolute max.
Connection Detail
STOP and -, when
connected together
will cause the Receiver
to power down
S-, S+ Connections
For Safety Solenoid etc.
Part No. 9820 or 9821
RS232 connection
for programming and
special features
Supply 12/24 V DC
40 Volts ABSOLUTE MAX
Outputs sockets
+, -, F1& F2
F3, F4, and Master.
The Receiver is designed
to handle 15 Amps, current
draw in excess of this will
trigger a system shut down.
Lk1, when bridged
causes the Master
Output to be
Parallel
Any output can handle
this maximum current.
LK2, when bridged
causes the Master
Output to be
Continuous
SMA connector for
External Aerial Antenna
Part No. 9861, 9862,
9863 or 9869
Jumper MUST be
fitted to only ONE link
Standard (Internal) Antenna
connection
Your product is marked with this symbol. It means that used
electrical and electronic products should not be mixed with
general household waste. There is a separate collection
system for these products.
In the EEC - Please contact your National Distributor (see
www.lodar.com for this information) who will inform you about
the take-back of the product. You might be charged for the
costs arising from the take-back and recycling. Small products
might be taken back by your local collection facilities.
Outside the EEC - If you wish to discard this product
please contact your local authorities and ask for the correct
method of disposal
POWER DOWN RECEIVER BEFORE MAKING CHANGES
CONTACT INFORMATION
Lodar
60 Sandwell Street,
Walsall, WS1 3EB.
England
Tel: +44 (0)1922 613633
Fax: +44 (0)1922 626991
email: sales@lodar.com
www.lodar.com
92104.05 FET 24

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Martin
Title                           : Untitled-1
Create Date                     : 2014:01:17 09:58:24Z
Creator Tool                    : CorelDRAW X6
Modify Date                     : 2014:05:22 10:15:38+01:00
Metadata Date                   : 2014:05:22 10:15:38+01:00
Producer                        : Corel PDF Engine Version 16.0.0.707
Document ID                     : uuid:556713c1-8883-486f-9e99-f41eca7f4f9d
Instance ID                     : uuid:b7e0cb65-a385-4979-9a42-cbd91c01895b
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 2
Author                          : Martin
EXIF Metadata provided by EXIF.tools
FCC ID Filing: M2HP03

Navigation menu