Lodar P03 Transmitter Standard-433 User Manual

Lodar LTD Transmitter Standard-433 1

a href="https://usermanual.wiki/Lodar" itemprop="url"> Lodar >

Contents

User manual

2or Disconnect BatteryIDENTIFY POWERCONNECTION POINTAND ISOLATE SUPPLYFuseRemove fuseVehicle  batteries  contain  gasses which  are  flammable  and  explosive. Wear eye protection and do not lean over battery while disconnecting. Do !WARNING1.   The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Ampsthrough one output or 5 Amps  each through 3 outputs.2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf fordetails.3. If Receiver outputs are connected in parallel with an external switching device (wired remote)the Receiver will instantly  switch off when the wired remote is operated4. Lodar Receivers  have an isolation switch for safety, to allow for registering a MUSTreplacement Transmitter.5. Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes ofinactivity. This can be altered, ask your dealer.1!BEFORE YOU STARTWiring Instructions for 2 & 4 Function, 92 & 93 Series, FET Receivers.92 02/4 RX & 93 02/4 RXhave 7 core cableCONNECTWIRES4TransmitterFunction Convention92 00 RX & 93 00 RXhave 4 core cablewww.lodar.com9000F1 F2F3 F45or re-connect BatteryACTIVATE THE RECEIVER SUPPLYFuseReplace fusePress the Transmitter   buttonRESETto activate the system, and carefully test each function for correct operation.7TEST6CONNECT TRANSMITTER BATTERYBatteries generally have to be disconnected when shipping.3Secure using 5mm (3/16") bolts (not supplied)through the 4 mounting feetTAKE TIME TO LOCATE THE BEST POSITIONIf necessary, power the Receiver and move it aroundthe vehicle until the required performance is achieved.Operate the Transmitter and observe the Receiverinternal LED’s.Mount as HIGH as possibleAVOID surfaces with HEAVY VIBRATIONAVOID DIRECT SPRAY from wheelsIn a HOT CLIMATE fit in a SHADED positionCable gland should face DOWN or BACKReceiver 92 04 RX and 93 04 RX shown,Waterproof to IP67, complete with 3 metres (10 ft) cablesCAUTIONMOUNT RECEIVER STOP POSITIVENEGATIVE!12/24 Volts DC NominalPositive SupplyREDNegativeBLACKGREENYELLOWBROWNBLUEWHITEOutput Function 1Output Function 2Output Function 3Output Function 4Output Function MasterWire used forWire ColourNot PresentNot PresentNot PresentNot UsedNot Used9200RXand 9300RX9202RXand 9302RX9204RXand 9304RXMake notes about theconnections made in the boxes belowWhat is the MASTER Output for ?It is used to operate the pump of an electro-hydraulicpower pack or maybe a clutch pump. It can also be used for powering a dump valve, master valve etc.It can be configured to work continuously, that is ONwhen SET is pressed and OFF when STOP is pressed; or in parallel with any output, that is, it isactive only a function is operated. If it is needed with certain functions only, this can easily be configured.92104.05 FET 24
Download:
Mirror Download [FCC.gov]
Document ID2363898
Application IDpnpKvKoxxAt/p7A+ehSM5A==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize238.95kB (2986920 bits)
Date Submitted2014-08-20 00:00:00
Date Available2014-08-20 00:00:00
Creation Date2014-01-17 09:58:24
Producing SoftwareCorel PDF Engine Version 16.0.0.707
Document Lastmod2014-05-22 10:15:38
Document TitleUntitled-1
Document CreatorCorelDRAW X6
Document Author: Martin
FCC ID Filing: M2HP03

Navigation menu