Logi D LD2EA0003 Gen II Fly By Antenna Board User Manual
Logi-D Gen II Fly By Antenna Board
Logi D >
User Manual
1-800-922-8649 ou 514-866-0001
www.tecsys.com
450-628-8800 ou 1-888-628-8804
www.logi-d.net
LD2-EA0003
Fly By Antenna Board
User Manual
Revision: 01
ESD
(EN) Warning: This module is ESD sensitive. Electrostatic discharges can permanently damage the module. Handle
with proper grounding equipment and techniques.
(FR) Attention: Ce module est sensible aux décharges électrostatiques, qui peuvent lui infliger des dommages
permanents. Manipuler avec l’équipement et les méthodes appropriés de mise à la terre.
RF Emission
(EN) Warning: This module contains radio-frequency transceivers and antennas which emits and receive in the
13.56 MHz frequency band. This module can interfere with and its functionality can be impacted by other nearby
equipment operating in the same frequency band.
(FR) Attention: Ce module contient des émetteurs-récepteurs et antennes qui émettent et reçoivent dans la plage
fréquentielle de 13.56 MHz. Ce module peut interférer et ses fonctionnalités peuvent être altérées par de
l’équipement avoisinant opérant dans la même plage fréquentielle.
RF Exposure
(EN) Warning: Exposure to Radio Frequency Energy: The radiated power output of the RFID module is below the RF
exposure limits for uncontrolled exposure. This device should be operated with a minimum distance of at least 20
cm between the RFID antenna and a person’s body.
(FR) Attention: Évaluation d'exposition aux RF: L’intensité de champ RF émis par la carte RFID est inferieures aux
limites d'intensité de champ RF prévues pour l’environnement non contrôlé. Les dispositifs à un élément rayonnant
fonctionnant normalement à des distances de séparation entre l'utilisateur et le dispositif supérieures à 20 cm.
P a g e | 2
1-800-922-8649 ou 514-866-0001
www.tecsys.com
450-628-8800 ou 1-888-628-8804
www.logi-d.net
FCC part 15 Warnings
FCC 2-parts warning statement under 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Modification statement 15.21
The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
IC warning statement
(EN) Warning: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
(FR) Attention: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
P a g e | 3
1-800-922-8649 ou 514-866-0001
www.tecsys.com
450-628-8800 ou 1-888-628-8804
www.logi-d.net
Labelling Requirements for the Host Device
The host device shall have a label with following content:
Contains
FCC ID : 2ADCY-LD2EA003
IC : 12416A-LD2EA0003
FCC part 15 Warnings
FCC 2-parts warning statement under 15.19
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Modification statement 15.21
The user manual or instruction manual for an intentional
or unintentional radiator shall caution the user
that changes or modifications not expressly approved by
the party responsible for compliance could
void the user's authority to operate the equipment.
IC warning statement
(EN) Warning: This device complies with Industry
Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
(FR) Attention: Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
Figure 1: FCC/IC label requirement.
Installation
This installation must be completed by a qualified technician. The LD2-EA0003 PCB module is to be installed only in
a smartpanel product (Logi-D product). To function properly, it must be connected to a compliant host computer
LD2-EA0001. This supplies 5VDC to the board.
To install the module LD2-EA0003:
Place the module in the smartpanel enclosure, with the LEDs facing the wall of the enclosure. The
components side should face the open side of the enclosure. This way the modular transmitter meets all
the applicable part 15 requirements under the operating conditions in which the transmitter will be used.
Secure the module in place with two (2) screws.
Connect the ribbon cable from the host controller in the IDC connector.