LogicMark CS40915B CaretakerSentry Basic Pendant User Manual

LogicMark, LLC CaretakerSentry Basic Pendant

User Manual

Quick Install GuideInstructions for Adding a Waterproof Pendant to Your CaretakerSentryManufacturer’s Disclaimers and Limited WarrantyCOMMUNICATION AND RESPONSE LIMITATIONS: Purchaser acknowledges that signals which are transmitted over telephone lines, or other modes of communication pass through communication networks wholly beyond the control of The Manufacturer and are not maintained by The Manufacturer, and, therefore, The Manufacturer shall not be responsible for any equipment or com-munication failure which prevents transmission signals from reaching your contact list including emergency 911 operators or dam-ages arising therefrom. Purchaser acknowledges that The Manufacturer provides no response to the System’s equipment. The equipment is designed to communicate with the a central station of your choice and The Manufacturer is not and shall not be responsible for ambulance, police or other emergency response time or that any response will be provided by the central monitoring station.TESTING AND SERVICE OF THIS EQUIPMENT: The equipment, once installed, are in the exclusive possession and control of the Purchaser, and it is Purchaser’s sole responsibility to test the operation of equipment and request warranty service if the equipment is under warranty.PURCHASER’S EXCLUSIVE REMEDY: Purchaser’s exclusive remedy for The Manufacturer’s default hereunder is to require The Manufacturer to repair or replace, at The Manufacturer’s option, any equipment or part of the personal emergency alert system which is non-operational during The Manufacturer’s warranty period.LIMITATION OF LIABILITY: This equipment is not designed or guaranteed to prevent any loss or injury. This Limited Warranty and Disclaimer of Liability constitutes the terms of sale and use of the equipment, and if there should arise any liability on the part of The Manufacturer as a result of any cause whatsoever, regardless of whether or not such loss, damage, or personal injury was caused by or contributed to by The Manufacturer’s negligence to any degree or failure to perform any obligation or strict products liability, such liability will be limited to an amount paid by the Purchaser to The Manufacturer for the product, or to the sum of $350.00, whichever is greater.For warranty information, see your dealer for details.PendantPart #40915Gray Emergency Button2 Second PushRed Status LEDBreakaway FeaturePendant on Lanyardv7.4Base Unit - Model 40914 FCC ID: TYD-CS40914 IC: 8471A-CS40914 Waterproof Pendant - Model 40915b FCC ID: TYD-CS40915B IC: 8471A-CS40915B REN 3.7Pendant on Wrist StrapBase Top ViewPart #40914Red Emergency button (Blue)(Green)(Red)Blue CareTaker buttonMicrophone(Yellow)SpeakerCancel (1 second)System Check (8 seconds)Base Back ViewTelephone JacksLine IN To House Phone Programming SwitchProgramming Mode “Emergency Call Mode”Normal OperationResetPower DC 7.5 800 mAhCode Learn(Red)Cellular Accessory JackBase Side View
Step-by-Step Installation GuideConfirm Accessories in Kit1Waterproof pendantWrist Strap(Shown with waterproof pendant)LanyardTest the Unit3Red Code Learn buttonTeach the Pendant to the System2On the Base Unit a. PUSH and RELEASE the RED Code Learn button on back of base unit. You will hear a voice prompt, “Pendant Learning.”On the Pendanta. PUSH the GRAY Emergency button until you hear, “Pendant Learning” from the base. Then, release the button on the pendant. i. If you hear, “Base and Pendant out of Range,” STOP - wait 30 seconds and begin step 2 again.b. When pendant learning has been successful, you will hear, “Pendant Code Learned,” and then it will announce the call setting that the base is set to Programming Mode or Emergency Call Mode.*NOTES:Erasing all previously learned pendants – hold down the (Red) Code Learn button for 8 seconds. You will hear the confirmation of “Erasing All Pendants, All Pendants Erased” from the base unit. Now you can re-teach pendants starting at Step #2.Lost Pendants – If a pendant has been lost, follow the note for “Erasing all previously learned pendants” and then re-teach all of the pendants starting at Step #2.Teaching additional pendants - does not erase previously learned pendants.Exiting Learning Mode - Base will automatically exit the pendant learning mode after successfully learning the pendant or after the base announces “Pendant Learning Failed”.Up to 9 waterproof pendants can be taught to each base.Place call to Emergency Operator:a. Push the GRAY EMERGENCY button for 2 seconds on Pendant. (The RED LED on the pendant should turn ON for 1 second.)b. You should hear a dial tone, dialing, and then communication tones between the CaretakerSentry and central station. Several seconds later the operator should answer the call.c. Talk normally to the base unit – just like into a speaker phone.d. At the end of the conversation, the CaretakerSentry should automatically hang-up – if not, push the CANCEL button for 1 second.Performing a System Test a. PUSH and HOLD the CANCEL button for 8-10 seconds to enter “System Check” b. Push the GRAY EMERGENCY button for 2 seconds on Pendant. (The RED LED on the pendant should turn ON for 1 second.) c. Listen for the voice prompt from base unit:i. “All Systems are OK – Battery is OK” is heard if the system is correctly installed.ii. If any other voice prompt is heard, the unit will describe the problem.d. Push and release the CANCEL button for 1 second to exit Test Mode. (The unit will automatically exit in 3 minutes.) e. We recommend that you perform this System Test weekly.
Note : Cet appareil est conforme à la Partie 15 des règlements de la FCC et aux normes RSS de l’Industrie du Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer des interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent provoquer un fonctionnement indésirable. Le fabricant n'est pas responsable des toutes interférences radio ou télévision causées par des modifications non autorisées apportées à cet appareil. De telles modifications peuvent empêcher l’utilisateur d’utiliser l'appareil.This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 5mm between the radiator and your body.

Navigation menu