Logitech G700 Quick Start For Hardware Installation User Manual To The D8a176ed 4aa4 4996 9c01 Dc9510730a61

User Manual: Logitech G700 to the manual

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

Quick Start for Hardware Installation:
Avaya G700 Media Gateway
and
Avaya S8300 Media Server

555-233-150
Issue 8
February 2007

© 2007 Avaya Inc.
All Rights Reserved.
Notice
While reasonable efforts were made to ensure that the information in this
document was complete and accurate at the time of printing, Avaya Inc. can
assume no liability for any errors. Changes and corrections to the information
in this document may be incorporated in future releases.
For full support information, please see the complete document,
Avaya Support Notices for Hardware Documentation, document number
03-600759.
To locate this document on our Web site, simply go to
http://www.avaya.com/support and search for the document number in
the search box.
Documentation disclaimer
Avaya Inc. is not responsible for any modifications, additions, or deletions to
the original published version of this documentation unless such modifications,
additions, or deletions were performed by Avaya. Customer and/or End User
agree to indemnify and hold harmless Avaya, Avaya's agents, servants and
employees against all claims, lawsuits, demands and judgments arising out of,
or in connection with, subsequent modifications, additions or deletions to this
documentation to the extent made by the Customer or End User.
Link disclaimer
Avaya Inc. is not responsible for the contents or reliability of any linked Web
sites referenced elsewhere within this documentation, and Avaya does not
necessarily endorse the products, services, or information described or offered
within them. We cannot guarantee that these links will work all of the time and
we have no control over the availability of the linked pages.
Warranty
Avaya Inc. provides a limited warranty on this product. Refer to your sales
agreement to establish the terms of the limited warranty. In addition, Avaya’s
standard warranty language, as well as information regarding support for this
product, while under warranty, is available through the following Web site:
http://www.avaya.com/support.
Copyright
Except where expressly stated otherwise, the Product is protected by copyright
and other laws respecting proprietary rights. Unauthorized reproduction,
transfer, and or use can be a criminal, as well as a civil, offense under the
applicable law.
Avaya support
Avaya provides a telephone number for you to use to report problems or to ask
questions about your product. The support telephone number
is 1-800-242-2121 in the United States. For additional support telephone
numbers, see the Avaya Web site: http://www.avaya.com/support.

Contents

Chapter 1: Before You Go to the Installation Site . . . . . . . . . . . . .

Other documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

License file, software, and firmware . . . . . . . . . . . . . . . . . . . . . . . . .

Laptop requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2: Conduct Equipment Inventory . . . . . . . . . . . . . . . . .

Chapter 3: Mount Media Gateway . . . . . . . . . . . . . . . . . . . . .

Chapter 4: Install Octaplane Stacking Module. . . . . . . . . . . . . . .

Chapter 5: Connect Media Gateways . . . . . . . . . . . . . . . . . . .

Chapter 6: Install S8300 Media Server . . . . . . . . . . . . . . . . . . .

Chapter 7: Install Media and Expansion Modules . . . . . . . . . . . . .

Chapter 8: Install USB Modem and CD-ROM Drive . . . . . . . . . . . .

Chapter 9: Install UPS and Apply Power . . . . . . . . . . . . . . . . . .

Chapter 10: Connect the Laptop — G700 without an S8300 . . . . . . .

Chapter 11: Connect the Laptop — G700 with S8300 . . . . . . . . . . .

Issue 8 February 2007

Contents

4 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 1: Before You Go to the Installation Site
The following activities must be completed before going to an installation site.

Other documents
Obtain access to the following documentation:
●

The G700/S8300 Installation guide: Installation and Upgrades for Avaya G700 Media
Gateway and Avaya S8300 Media Server, 555-234-100.

●

The documentation library on CD, installed on your laptop, or accessible from the Avaya
Support web site: Documentation for Avaya Communication Manager, Media Gateways
and Servers, 03-300151.

License file, software, and firmware
The following tasks must be completed before you can install an Avaya S8300 Media Server
and Avaya G700 Media Gateway.

To do before you install the S8300 and G700
1. Meet with the customer to complete the Electronic Preinstallation Worksheet. The
Electronic Preinstallation Worksheet contains specific information about the customer’s
network configuration and telephony requirements. This information is required to use the
Avaya Installation Wizard to configure the Avaya IP solution.

Note:

Note:
To use the Avaya Installation Wizard, Release 2.0 or later of Communication
Manager must be installed on the media server. If a pre-2.0 release of the
Communication Manager is installed on the media server, the software must be
upgraded before the Avaya Installation Wizard can be used.
Note:
The current release of the Avaya Installation Wizard supports only an
English-language operating system.
2. If you are using the Avaya Installation Wizard to generate basic translations on an S8300
primary controller in a G700, get the customer’s Name and Number list file and the Custom
Templates. Copy these files to your laptop. The Electronic Preinstallation Worksheet
contains instructions for the Name/Number and Custom Templates files.

Issue 8 February 2007

Before You Go to the Installation Site

3. Retrieve the required license file from Remote Feature Activation (RFA).
Note:
As of Communication Manager Release 3.1, the Avaya Installation Wizard no
longer requires the inclusion of the FEAT_DADMIN login permissions in the
license in order to generate basic translations. However, for Business Partners,
the license may still include the FEAT_DADMIN login permissions.

Note:

4. Obtain a password (authentication) file from Authentication File System (AFS).
5. Obtain the most recent versions of software and firmware on CD-ROM. Check for and
download the most recent versions of firmware from http://support.avaya.com or, if
necessary, from the Download Center.
6. Determine if the customer purchased a USB CD-ROM drive as part of the order. If the order
does not include a USB CD-ROM drive, obtain a USB CD-ROM drive for temporary use at
the site.
7. The technician will be advised if ProVision will be used in addition to the Avaya Installation
Wizard. ProVision can be used to upload all of the Communication Manager translations.
Information on the Avaya Installation Wizard options for ProVision is in the Electronic
Preinstallation Worksheet.

Laptop requirements
The laptop PC that you use to access the S8300 and/or G700 and to launch the Avaya
Installation Wizard must meet the following requirements:
●

A minimum display resolution of 800 by 600

●

10/100 ethernet card installed

●

Windows 95 or later

●

Internet Explorer 5.0 or later

●

A serial communication interface

Once you have verified that all the above activities are completed, you can begin product
hardware installation following the instructions in this guide.

6 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 2: Conduct Equipment Inventory
The following list of equipment contains items that may not be needed for your configuration —
those items are specified as "optional" and may not be included in your inventory.
Avaya G700 Media Gateway Chassis
51
ALM PWR CPU MSTR

LNK COL Tx

58
EXT1 EXT2

FDX FC Hspd LAG

V4
EXT1

EXT2

Optional Avaya S8300B Media Server
ALM
TST
ACT
OK TO
REMOVE

SHUT DOWN
SERVICES

USB1

USB2

Optional Avaya S8300C Media Server
ALM
APP
ACT
OK TO
REMOVE

S8300C
C_V1

SHUT DOWN
SERVICES

USB 1

USB 2

USB 3

S8300C LAO 092006

$/0
767
$&7
6,*

Optional Avaya MM710 T1/E1 Media
Module

(,$$'&(

AVAYA

ALM
TST
ACT

Optional Avaya MM711 Analog Media
Module

Note:

AVAYA

ALM
TST
ACT

Note:
The Analog and the DCP
media modules look similar.
Check their labels to verify
the module type.

Optional Avaya MM712
DCP Media Module

Note:

Note:
The DCP and the Analog
media modules look similar.
Check their labels to verify
the module type.

Optional Avaya MM714 4FXS x 4FXO
Analog Media Module

Issue 8 February 2007

Conduct Equipment Inventory

ALM
TST
ACT

MM716
ANALOG

Optional Avaya MM716 24-port Analog
Media Module

VH0

mmdc716 LAO 102505

Optional Avaya MM717 24-port DCP Media
Module.

ALM
TST
ACT

Note:

Note:
Endpoints connected to this
media module must be
in-building only.

Optional Avaya MM720 8-port BRI Media
Module

Optional Avaya MM722 2-port BRI Media
Module

Optional Avaya MM760 VoIP Media Module
AVAYA

ALM
TST
ACT

Optional Expansion Module.
51

X330T16

Optional C360 Converged Stackable
Switch:
C363T/C363-PWR
C364T/C364-PWR
Optional X330STK Octaplane
Stacking Module.

8 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Optional USB modem.
Material ID: 700235526

Optional CD-ROM or DVD/CD-RW drive:
●

Teac USB CD-ROM Drive. Material
ID: 700289580.

●

Addonics USB DVD/CD-RW Drive.
Material ID: 700406267
(Available with S8300C only)
DVD/CD-RW drive for S8300/S8400.
Material ID: 700406267

●

Optional industrial-strength Compact Flash
card and Compact Flash drive available
through your Avaya sales representative.

h1dccfla LAO 110306

Optional Uninterruptable Power Supply
(UPS) for AC-Powered Gateways Only.

Note:

Note:
A stand-alone version of the
UPS is shown.

Issue 8 February 2007

Conduct Equipment Inventory

Screw Packet and Rack Mount Brackets
For each bracket:

Note:

●

three flat-head machine screws
attach the bracket to the G700

●

two round-head lock-washer machine
screws attach the bracket to the rack
Note:
There are four sizes of
lock-washer screws in the
packet for attaching the
brackets to the rack. Use the
appropriate size screws to
match the specific hole size
of the rack.

Optional X330SC Short Cable.

Note:

Note:
The X3300SC Short Cable
is sometimes shipped
attached to the X3300STK
Octaplane Stacking Module.

Optional X3300RC Redundancy Cable.

Optional X3300 LC Long Cable.

10 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Optional USB Cable and Adapter for use
with the USB modem.

Crossover Ethernet Cable (CAT5)

Serial or "Console" Cable and Adapter

Ground wire.

Issue 8 February 2007

Conduct Equipment Inventory

Optional AC Power Cord

Optional DC Power Cord.

Feet used for table mounting.

12 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 3: Mount Media Gateway

1. Wear an anti-static ground wrist strap
and attach to an approved ground.
2. For rack mount, install the mounting
brackets on the left and right sides of
the gateway chassis using the
flathead screws from the bracket
packet.

Note:

Note:
The brackets can also be
installed in the middle of the
chassis.
3. Lift the media gateway chassis and
mount in a rack using two lock-washer
screws for each bracket.

! CAUTION:
CAUTION:

The weight of the media
gateway is unevenly
distributed and may require
two persons to mount in the
rack.

Issue 8 February 2007

Mount Media Gateway

51
ALM PWR CPU MSTR

LNK COL Tx

58
EXT1 EXT2

FDX FC Hspd LAG

4. For desktop mount. Install feet using
plastic push rivets.

V4
EXT1

EXT2

5. Connect the ground wire to the ground
conductor on the back of the media
gateway.
6. Attach the other end of the ground
wire to an approved ground.

14 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 4: Install Octaplane Stacking Module

Note:

Note:
Complete these steps only if you are connecting more than one G700 Media
Gateway in a stack configuration.

1. Remove the blank faceplate from
the Octaplane slot on the back of
the media gateway.

2. Align the X330STK Octaplane
Stacking Module with the interior
guides and insert until firmly
seated

!
WARNING:

WARNING:
To prevent damage to
equipment, handle the
module by the
faceplate or edge.

3. Tighten the captive screws.

Issue 8 February 2007

Install Octaplane Stacking Module

16 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 5: Connect Media Gateways

Note:

Note:
Complete these steps only if you are connecting more than one G700 Media
Gateway in a stack configuration.
1. Using the gray X330SC short cables,
connect the media gateways from the
bottom up:
●

Connect the light gray connector to the
port labeled “Cable to upper unit.”

●

Connect the dark gray connector to the
port labeled “Cable to lower unit.”

●

Repeat both steps until all units in the
stack are connected (maximum of 10
units).

2. For single-stack redundancy, connect the
bottom unit and the top unit using the
black X330RC redundancy cable:
●

Connect the light gray connector to the
port labeled “Cable to upper unit: on
the top unit of the stack.

●

Connect the dark gray connector to the
port labeled “Cable to lower unit” on
the bottom unit of the stack.

Single-stack redundancy

Issue 8 February 2007

Connect Media Gateways

3. For multiple stack redundancy, connect
the stacks using the black X330RC
redundancy cable and the gray X330LC
long cable:
●

Connect the light gray connector of the
black X330RC redundancy cable to the
port labeled “Cable to upper unit” on
the top unit of the stack 2.

●

Connect the dark gray connector of the
black X330RC redundancy cable to the
port labeled “Cable to lower unit” on
the top unit of the stack1.

●

Connect the light gray connector of the
gray X3300LC long cable to the port
labeled “Cable to upper unit” on the top
unit of the stack 1.

●

Connect the dark gray connector of the
gray X330LC long cable to the port
labeled “Cable to lower unit” on the
bottom unit of the stack 2.

Multiple-stack redundancy

18 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 6: Install S8300 Media Server

Note:

Note:
Complete these steps if you are installing an S8300 Media Server (configured as
the primary controller or as a Local Survivable Processor).

1. From the front of the G700 Media
Gateway, remove the blank faceplate
from slot V1.

2. For an S8300B, remove the LED
module (located above slot V1) and
place in an anti-static bag.
For an S8300C, you do not need to
remove the LED module.

3. Align the S8300 Media Server with the
lower interior guides.
For an S8300B, insert about 2" into slot
V1.
For an S8300C, insert all the way into
slot V1 until the faceplate is flush with
the LED module.

Issue 8 February 2007

Install S8300 Media Server

4. For an S8300B, align the LED module
with the upper interior guides and
insert until the faceplate is flush with
the S8300B Media Server.
5. For an S8300B, continue inserting both
modules together until firmly seated.

!
WARNING:

51
ALM PWR CPU MSTR

LNK COL Tx

ALM
TST
ACT
OK TO
REMOVE

58
EXT1 EXT2

FDX FC Hspd LAG

WARNING:
Failure to seat both modules
together could result in
equipment damage.

6. Tighten the captive screws on the
S8300.

V3
SHUT DOWN
SERVICES

USB1

USB2

V4
EXT1

EXT2

20 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 7: Install Media and Expansion Modules

Note:

Note:
In each gateway, a single expansion module can be installed in the lower left slot
only. If the S8300 is installed (in slot V1), up to 3 media modules can be installed
in slots V2–V4. If no S8300 is installed, a fourth media module can be installed in
Slot V1.

1. To install a media module, first remove
the upper right blank faceplate.

Note:

Note:
All slots must have either a
module installed or be
covered by a blank face plate.
Do not leave any slots
uncovered.
2. Align the media module with the interior
guides and insert into slot until firmly
seated.
3. Tighten the captive screws.
4. Repeat steps 1 through 3 for each media
module to be installed.

5. To install the expansion module, first
remove the lower left blank faceplate.
6. Align the expansion module with the
interior guides and insert into slot until
firmly seated.
7. Tighten the captive screws.

Issue 8 February 2007

Install Media and Expansion Modules

22 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 8: Install USB Modem and CD-ROM Drive

USB Modem
1. Connect the USB cable to one of the
USB ports on the faceplate of the S8300.
2. Following the instructions packaged with
the modem, connect the other end of the
USB cable to the modem.
3. Connect the analog telephone line to the
RJ-11 jack on the modem.

USB CD-ROM/DVD Drive
The USB CD-ROM or DVD/CD-RW drive is
used primarily as a software source location
when remastering an S8300 hard drive.
1. Connect the USB cable into one of the
USB ports on the faceplate of the S8300.
2. Connect the other end of the USB cable
to the CD-ROM or DVD/CD-RW drive.
3. If you are using an Addonics DVD/
CD-RW drive, connect the power cord to
the drive and an electrical outlet.

Note:

Note:
The TEAC drive and S8300/
S8400 drive get their power
from the server over the USB
connection.

4. If you are using an Addonics DVD drive,
set the power source switch on the side
to EXT, not USB. See item 1 in the figure
to the left.

nic

s
EX
T

1
h1dcadvd LAO 103006

5. If you are using an S8300/S8400 DVD/
CD-RW drive, set the on/off switch to
On.
Be sure to set the S8300/S8400 drive to
Off when not in use.

Issue 8 February 2007

Install USB Modem and CD-ROM Drive

24 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 9: Install UPS and Apply Power

UPS (AC only)
1. The UPS is an option for AC-powered
gateways only. From the back of the
G700 Media Gateway, connect the
Uninterruptable Power Supply (UPS)
using the manufacturer’s instructions.

Note:

Note:
A stand-alone version of the
UPS is shown.

AC power
1. Apply power to each media gateway
by connecting the AC power cord.

Note:

Note:
There is no on/off switch.
The units will power up
when connected.

Issue 8 February 2007

Install UPS and Apply Power

DC power
1. Apply power to each media gateway
by connecting the DC power cord.

Note:

Note:
There is no on/off switch.
The units will power up
when connected.

26 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 10: Connect the Laptop — G700 without an
S8300
This section assumes the G700 does not contain an S8300 Media Server. Use the Gateway
Installation Wizard from the laptop to enter the initial gateway configuration parameters.
1. Connect the RJ45 end of a serial
cable to the Console port on the
lower right of the front of the
G700.
2. Connect the other end of the
cable to the Serial port on the
laptop.

3. Power on the laptop.
4. Start a Hyperterm (or similar
application) session.
5. Start the Gateway Installation
Wizard (GIW).

Issue 8 February 2007

Connect the Laptop — G700 without an S8300

6. Follow the GIW instructions to
Enter the configuration
parameters.

ALM PWR CPU MSTR

LNK COL Tx

V2
EXT1 EXT2

FDX FC Hspd LAG

To connect to the customer’s
LAN

V4
EXT1

EXT2

1. Connect a straight Ethernet
cable to one of the Ethernet
ports (labeled Ext 1 and Ext 2)
on the front of the G700.
2. Connect the other end of the
cable to a LAN connector.

28 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Chapter 11: Connect the Laptop — G700 with S8300
This section assumes the G700 has an S8300 Media Server installed.

1. Connect a crossover Ethernet cable to
the Services port on the faceplate of the
S8300 Media Server.
2. Connect the other end of the cable to
the Ethernet port on the laptop.

3. Power on the laptop.
4. Start an SSH session with PuTTY or
another SSH tool.
5. Use SSH to connect to 192.11.13.6.
6. Specify port 22, if requested.

7. When the first RP installer page
appears, select options as appropriate
and continue to complete the software
installation.

Issue 8 February 2007

Connect the Laptop — G700 with S8300

8. Verify the Services network settings:
a. IP Address: 192.11.13.5
b. Subnet Mask: 255.255.255.252
c. Domain Name Service (DNS):
disabled.
9. Open MS Internet Explorer and disable
the Proxy Server.
10. In the browser address field, initiate
access to the S8300 by typing in lower
case:
http://192.11.13.6
11. Click Continue to access the Logon
page.
12. Click OK or Yes, as appropriate, for any
security pages that may appear prior to
the Logon page.
13. Log in to the S8300 Media Server with
the craft login and password for initial
installation.

30 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

14. Select Administrator Accounts from the
menu, and add a super-user (SUSER)
login. Assign the login to the suser
login group of and the prof18 additional
group.

Note:

Note:
An SUSER group must be
created before you can install
the authentication file. The
authentication file is installed
automatically by the Avaya
Installation Wizard.

15. Use the Avaya Installation Wizard. Click
on Launch Avaya Installation Wizard
and continue.

Note:

Note:
If you are not using the
Avaya Installation Wizard,
refer to Installation and
Upgrades for Avaya G700
Media Gateway and Avaya
S8300 Media Server,
555-234-100, for additional
instructions.

To connect to the customer’s LAN
ALM PWR CPU MSTR

LNK COL Tx

V2
EXT1 EXT2

FDX FC Hspd LAG

V4
EXT1

EXT2

1. Connect a straight Ethernet cable to
one of the Ethernet ports (labeled Ext 1
and Ext 2) on the front of the G700.
2. Connect the other end of the cable to a
LAN connector.

Issue 8 February 2007

Connect the Laptop — G700 with S8300

To connect USB Modem
To configure the G700 and S8300 remotely,
connect the USB modem.
1. Connect the USB cable to either of the
two USB port on the faceplate of the
S8300.
2. Following the instructions packaged
with the modem, connect the other end
of the USB cable to the modem.
3. Connect the analog telephone line to
the RJ-11 jack on the modem.
4. Go to the Maintenance Web Interface
and select Modem in the Security
Category.
5. Select the box labeled "Enable modem
for unlimited incoming calls" an click
Submit.

32 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2006:11:14 07:41:09Z
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2006:11:14 07:57:03-07:00
Metadata Date                   : 2006:11:14 07:57:03-07:00
Format                          : application/pdf
Creator                         : .
Title                           : Quick Start for Hardware Installation: Avaya G700 Media Gateway and Avaya S8300 Media Server
Document ID                     : uuid:ec4a4883-1741-49f9-9a4c-bb8822f8b500
Instance ID                     : uuid:a3afe2c1-1e3f-4726-ae44-e7ab82213d1b
Page Count                      : 32
Page Layout                     : OneColumn

EXIF Metadata provided by EXIF.tools

Logitech G700 Quick Start For Hardware Installation User Manual To The D8a176ed 4aa4 4996 9c01 Dc9510730a61

Navigation menu

Versions of this User Manual:

Views

Navigation