Luminex 8543 HEATHER 12-INCH LED MW SENSOR CEILING LIGHT( User Manual 351 1542

Download:
Mirror Download [FCC.gov]
Document ID	3034960
Application ID	t1IJesCrR0C1IU+izEM9yg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	102.49kB (1281102 bits)
Date Submitted	2016-06-21 00:00:00
Date Available	2016-06-21 00:00:00
Creation Date	2015-06-26 16:51:53
Producing Software	Adobe PDF library 9.90
Document Lastmod	2016-05-30 14:08:08
Document Title	351-1542
Document Creator	Adobe Illustrator CS5

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
352-8543
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Customer Service: 1-800-887-6326 (weekdays 9 a.m. – 5 p.m. CST)
3. READ AND SAVE THESE INSTRUCTIONS.
Warning: LED electronics can be damaged by electro static discharge (ESD)shock. Before
installation, discharge yourself by touching a grounded bare metal surface to remove this
hazard. To avoid damage, do not touch the LED module.
Hardware Package (included):
Mounting Strap (A)
Mounting Screw (B)
Green Grounding
Screw (C)
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source. Using non-replaceable LED bulb.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
4. This sensor light has to be wired to its own switch.
Do not interconnect with others using the same
switch.
Maximum Wattage: 20 W
Working Temperature Range: 14°F ~ 122°F
Long Screw (D)
Wire Nut (E)
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
3. The built-in motion sensor with 360° of detection
range saves energy and makes life more convenient.
4. In manual override mode, the light remains on for 6
hours.
Outlet Box
House Grounding Wire
Wire Nut (E)
Mounting Strap (A)
Key Hole Slot
Green Grounding Screw (C)
Mounting Screw (B)
Long Screw (D)
Ceiling Pan
LED Module
Fig.1
Stud
Long Screw
Installation Steps
Slot
Turn off the power at fuse or circuit box.
1. Remove the plastic shade from ceiling pan.
Plastic Shade
2. Attach the two long screws to the holes on the
mounting strap. Thread them in part way: 2 to 3
turns only.
3. Attach the mounting strap to the outlet box using two
mounting screws.
Page 1/4
160526
4. Pull out the source wires from the outlet box. Make wire connections using wire nuts as follows:
---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
---Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.
---Attach the fixture grounding wire (usually green insulation or bare wire) to the mounting strap with the green
grounding screw, and then connect them to the house grounding wire with the wire nut.
Carefully put the wires back into the outlet box.
5. Attach the ceiling pan to the mounting strap by inserting two long screw heads into the key holes. Rotate the ceiling
pan until it is locked into place, and then tighten the long screws to secure it. (See Fig.1)
6. Attach the plastic shade back to the ceiling pan by aligning studs with slots, and turn it clockwise until it is locked in
place.
Turn on the power at fuse or circuit box
Function and Operation
Note: When power is first applied, the light will turn on. The sensor will take 15 seconds to warm up.
1. Auto Mode (daytime and nighttime operation)
Fig.2
● After warming up, the light enters into “AUTO” mode
Manual Override Operation Diagram
automatically. When motion is detected, the light turns on
Turn wall switch OFF-ON
and stays on as long as motion continues. When the motion
within 2 Seconds
is no longer detected, the light remains on for the
Auto
Manual
Mode
Override
predetermined time you set (8s ~ 12min), and then turn off
Mode
Turn
wall
switch
OFF-ON
automatically. (See Fig.3)
2. Manual Override (daytime and nighttime operation)
● Turn the wall switch “OFF” then turn it “ON” within 2 seconds,
the light remains on for 6 hours, and then return to “AUTO”
Fig.3
mode. To shift back to “AUTO” mode, turn the wall switch
“OFF” then turn it “ON” within 2 seconds again, or turn the
12Ft
wall switch “OFF” and then waiting over 8 seconds before
turning it on again. (See Fig.2)
Note: To make sure the above functions operate properly,
always keep the wall switch in the “ON” position (including
the daytime).
3Ft
within 2 Seconds,
Or turn wall switch OFF and
then waiting 8 seconds
before turning ON
6Min
8Sec 12Min
25Ft
SENS
TIMER
Customization Options:
Shut-off Delay
● The shut-off delay is the length of time the light will stay at brightness after motion has ceased to be detected.
● You can set the shut-off delay by rotating the delay time knob arrow so it points to the desired time setting within
“TIME” range. To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay, turn the
knob counterclockwise. (See Fig.3)
Detection range setting (sensitivity)
● Detection range is the term used to describe the diameter of the more or less circular detection zone produced on
the ground after mounting the sensor light at a height of 8.2 feet, turn the detection range control fully anti-clockwise
to select minimum detection range (approx.3 feet diameter), and fully clockwise to select maximum detection range
(approx. 25 feet diameter). (See Fig.3, Fig.4)
Fig.4
8.2'-11.5'
360º
Min:3'
Max:25'
Height of installation8.2' ~ 11.5'
Sensing distance adjustment range
Sensing angle adjustment range
Page 2/4
160526
NOTE:
a. The above detection range is gained in the case of a person who is between 5.2 feet ~ 5.6 feet tall with middle figure
and moves at a speed of 3.3 feet ~4.9 feet/sec. If person’s stature, figure and moving speed change, the detection
range will also change. In different cases, the sensitivity of the lights has certain deviation.
b. When using this product, please adjust the sensitivity (detection range) to an appropriate value but the maximum to
avoid the abnormal reaction caused by the easy detection of the wrong motion by the blowing leaves & curtains,
small animals or the interference of power grid & electrical equipment. All the above mentioned will lead to the error
reaction. When the product does not work normally, please try to lower the sensitivity appropriately, and then test it.
Friendly reminder: When installing two or more microwaves together, you are required to keep 13.1feet one from
another, otherwise the interference among them will lead to error reaction.
c. For best performance, install fixture at least 9.6 feet above the ground. At such a height, the fixture will provide a
detection distance of up to 25 feet at 77 degrees Fahrenheit. (See Fig.4)
d. The sensor detects movement across a detection range of 360 degrees. (See Fig.4)
e. Do not mount the fixture near fans or other motion-inducing objects.
Troubleshooting
Fault
Failure cause
Solution
The load fails to work.
The power is off.
Turn the power on.
The load works all the time.
There is a continuous signal in the region of the detection.
Check the settings of the
detection area. Please adjust
detection range.
The lamp isn't installed well so that sensor fails to
detect reliable signals.
Re-adjust the installation place.
Moving signal is detected by the sensor (movement
behind the wall, the movement of small objects, etc.)
Check the settings of the
detection area. Please adjust
detection range.
The motion speed is too fast or the defined detection
area is too small.
Check the settings of the
detection area. Please adjust
detection range.
The load works when there is
no motion signal detected.
The load fails to work when
there is motion signal detected.
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications
to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm between the radiator and your body.
Page 3/4
160526
The following parts are available for re-order if damaged or missing. Call us toll-free at 1-800-887-6326
Spare Parts List:
Assembly Kit
5559MM (1 SET)
Mounting Strap (A)
Long Screw (D)
Mounting Screw (B)
Green Grounding
Screw (C)
Wire Nut (E)
Plastic Shade
9817PS
5-YEAR LIMITED WARRANTY:
This Patriot Lighting fixture carries a limited warranty against defects in material or workmanship. If the Patriot Lighting
product fails at any time within five (5) years after the original date of sale due to defects in material or workmanship,
return the product to Menards with the original sales receipt. At its discretion, Patriot Lighting will replace the defective
fixture with the same or similar fixture or issue a refund. This warranty and any implied warranty (including but not limited
to any implied warranty of merchantability or fitness for a particular purpose) does not cover glass globes, light bulbs and
other expendable items. This warranty excludes coverage of finish or color against tarnishing, flaking, and discoloration.
If the original purchaser ceases to own the Patriot Lighting product this warranty and any implied warranty will be void.
This warranty does not cover damage caused by misuse or abuse, including but not limited to improper installation,
improper usage, accident, negligence, unauthorized repair, unauthorized modifications, or unauthorized maintenance of
the fixture. This warranty does not include reimbursement for inconvenience, installation, setup time, returned shipping
charges or defects, losses, labor, injuries to personal property.
This warranty gives the consumer specific legal rights, and the consumer may have other rights which vary from state to
state. The seller’s employees are not qualified to advise on the use of the fixture. Any oral representations made will
not be binding on seller or its employees.
For questions regarding this product, call toll-free at 1-800-887-6326.
Page 4/4
160526

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00
Format                          : application/pdf
Title                           : 351-1542
Creator Tool                    : Adobe Illustrator CS5
Create Date                     : 2015:06:26 16:51:53+08:00
Modify Date                     : 2016:05:30 14:08:08+08:00
Metadata Date                   : 2016:05:30 14:08:08+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 108
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 7492 bytes, use -b option to extract)
Rendition Class                 : proof:pdf
Original Document ID            : uuid:65E6390686CF11DBA6E2D887CEACB407
Document ID                     : xmp.did:2B2762CFC91BE5118C30DA54463D1F1B
Instance ID                     : uuid:0464dc29-c260-42ad-ac93-bad66624d342
Derived From Instance ID        : uuid:761113f0-7e39-4a2b-923b-12bf5f7f2c44
Derived From Document ID        : xmp.did:7810F6C98B19E511913B939BAC1D3D3E
Derived From Original Document ID: uuid:65E6390686CF11DBA6E2D887CEACB407
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved, saved
History Instance ID             : xmp.iid:BDBAA6CE4904E5118B1FECC7A029A8A6, xmp.iid:7810F6C98B19E511913B939BAC1D3D3E, xmp.iid:2B2762CFC91BE5118C30DA54463D1F1B
History When                    : 2015:05:27 16:24:35+08:00, 2015:06:23 17:39:48+08:00, 2015:06:26 16:51:51+08:00
History Software Agent          : Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5
History Changed                 : /, /, /
Startup Profile                 : Web
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 210.001652
Max Page Size H                 : 296.999959
Max Page Size Unit              : Millimeters
Font Name                       : ArialMT, Arial-BoldMT, ArialRoundedMTBold, TimesNewRomanPS-BoldMT, TimesNewRomanPSMT, SimHei
Font Family                     : Arial, Arial, Arial Rounded MT Bold, Times New Roman, Times New Roman, 黑体
Font Face                       : Regular, Bold, Regular, Bold, Regular, Regular
Font Type                       : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type
Font Version                    : Version 2.95, Version 5.06, Version 1.51, Version 5.07, Version 5.07, Version 5.01
Font Composite                  : False, False, False, False, False, False
Font File Name                  : Arial_0.ttf, Arial Bold.ttf, ARLRDBD_0.TTF, timesbd_0.ttf, times_0.ttf, simhei.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Group Name        : Web 颜色组
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: R=189 G=204 B=212
Swatch Groups Colorants Mode    : RGB
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Red     : 189
Swatch Groups Colorants Green   : 204
Swatch Groups Colorants Blue    : 212
Producer                        : Adobe PDF library 9.90
Page Count                      : 4
Creator                         : Adobe Illustrator(R) 15.0
For                             : User,
Bounding Box                    : -615 -1391 2653 -39
Container Version               : 11
Creator Version                 : 15

EXIF Metadata provided by EXIF.tools