Lutron Electronics 0034 Lighting Control Transceiver User Manual hybRPTR

Lutron Electronics Company Inc Lighting Control Transceiver hybRPTR

Contents

Users Manual

English FrançaisEspañol Português1Important NotesCodes: Install in accordance with all local and nation-al electrical codes.Power: The Hybrid Repeater can be powered fromEITHER of two sources:1. Adapter power. Use only the adapter pro-vided with the Hybrid Repeater (Lutronmodel # T120-9DC-3-WH).Caution - Using an adapter not rated at thefollowing specifications could damage therepeater and possibly overheat the adapter.• Input: 120 V 60 Hz• Output: 9 V 300 mA NEC Class 2; IEC PELV2. Link power. Use only power supplied via aHomeWorks Processor Hybrid RepeaterLink or a HomeWorks auxiliary power sup-ply. (See section about the HWI-PS in theHomeWorks Technical Reference Guide orApplication Note HW-104.) Each hybridrepeater counts as 30 LEDs. Note: An RF Processor does not supplypower on the Hybrid Repeater Link.Environment: Ambient operating temperature: 32-104°F (0-40°C), 0-90% humidity, non-condensing.Indoor use only.Please Read Before InstallingInstallation InstructionsOverviewHomeWorks Hybrid Repeaters add RF capability toHomeWorks processors configured with a HybridRepeater Link and provide an additional coveragearea for radio frequency (RF) signals sent betweenHomeWorks RF Dimmers/Switches, RF Keypads, andRF Processors. Each repeater covers a sphere ofapproximately 2500 square feet (232m2) of livingspace. Up to five (5) repeating devices may be placedin a HomeWorks RF system (a HomeWorks RFProcessor counts as one of the repeating devices).Hybrid RepeaterHR-REP-120120 V 60 Hz (9 V 300 mA adapter)HR-REP-120Hybrid Repeater Wiring: Hybrid Repeater wiringmust be in a daisy chain configuration. The totallength of wire on the Hybrid Repeater Link may be upto 1000 feet (305 m), and may contain up to five (5)Hybrid Repeaters.Cleaning: To clean, wipe with a clean damp cloth. DONOT use any chemical cleaning solutions.Device Placement: HomeWorks Hybrid Repeatersmust be located within 30 feet (9 m) of the RFDimmers, Switches, and Keypads they are covering.Hybrid Repeaters must also be within 60 feet (18 m)of an RF Processor or another repeater when usingthe RF Link for repeater-to-repeater or repeater-to-processor communication. When using the Wired Linkfor repeater-to-repeater or repeater-to-processor com-munication, a total wire length of 1000 feet (305 m)may be used.FCC InformationNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, persuant to part 15 of the FCC rules.Operation is subject to the following:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.
Wiring DiagramHR-REP-120(Side View)1. Find a suitable location for the Hybrid Repeater.Place the repeater in a convenient and accessiblelocation. Note: Hybrid Repeaters must be within 60feet (18 m) of an RF Processor or another repeaterwhen using the RF Link for repeater-to-repeater orrepeater-to-processor communication.2. Connect Hybrid Repeater Link (if applicable).Connect the Hybrid Repeater Link communicationwires from the HomeWorks®Processor (or previousHybrid Repeater in the daisy chain) to the terminalblock on the Hybrid Repeater (see WiringDiagram). Each terminal will accept up to three 22-18 AWG (0.5-1.0 mm2) wires. Note: If using the plug-in adapter to power therepeater, DO NOT connect the +15 V terminal (terminal 2).3. Apply power to the Hybrid Repeater. If theHybrid Repeater is to be powered by the HybridRepeater Link, apply power by turning on theHomeWorks Processor. If the Hybrid Repeater is tobe powered by the plug-in adapter, insert theadapter cord plug into the jack on the HybridRepeater, then plug the adpater into a standardwall receptacle.2EnglishFrançais EspañolPortuguêsInstallation Wall MountingHybrid Repeaters may be wall mounted using the supplied wall bracket.STATUS andTEST LEDs willbe dimly lit whenfirst poweredPlug inpower cordand adapterPlug inadapter jack1. Attach wall bracket to wall using the suppliedscrews and wall anchors.2. Place power cord into notches at top and bottom ofwall bracket. Wrap excess power cord around thecord holder. Route Hybrid Repeater Link wiringthrough hole in wall bracket and out through sidecutout. Align repeater and snap onto wall bracket.UPUPMUXMUX+15 VCOMPower CordHybridRepeater LinkWiringRF TX/RX LEDsIndicate RF Linkactivity.STATUS LEDIndicates the status of the HomeWorkssystem.Note: When the Hybrid Repeater ispowered, but has not yet been assignedan address from the HomeWorksIllumination Software, the STATUS andTEST LEDs will be dimly illuminated.OperationTEST LEDA slow flash indicatesRF communicationstests are in progressSTATUS ButtonUsed when addressing theHybrid Repeater from theHomeWorks IlluminationTMSoftware.TEST ButtonActivates RF communicationtests. To activate the tests,press and hold the TESTButton until the TEST LEDbegins to flash.Note: For communication tests,the Hybrid Repeater,HomeWorks Processor, andother RF devices must first beconfigured and addressedusing the HomeWorksIllumination Software.WIRED TX/RX LEDsIndicate Wired Linkactivity.
3English FrançaisEspañol PortuguêsSystem CommunicationsRF Communications Notes• Hybrid Repeaters must be located within 30 feet (9 m) of the RF Dimmers/Switches and Keypads they are covering. • Hybrid Repeaters must also be within 60 feet (18 m) of an RF Processor or another repeater. • Multiple repeaters may be necessary to provide adequate coverage. Up to four (4) repeaters may be used with eachRF Processor, and up to five (5) Hybrid Repeaters may be used with each 8 SeriesTM Processor or 4 SeriesTMProcessor (equipped with Hybrid Repeater Link).RF CommunicationsHybrid Repeater Link (Wired) Communications* Sta Sta*11223344RF TabletopKeypadRF Dimmer30 ft. (9 m) maximumRF ProcessorRF KeypadHybrid Repeater30 ft. (9 m) maximum60 ft. (18 m) maximumbetween RFProcessors andRepeaters, or betweenRepeatersHybrid Repeater Link1000 ft. (305 m) maximum wire run distanceHomeWorks®Processor(8 Series shown)RF Keypad30 ft. (9 m)maximum60 ft. (18 m)maximumHybrid RepeaterHybrid Repeater Link1000 ft. (305 m) maximumwire run distance
EnglishFrançais EspañolPortuguêsLutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299Made and printed in the U.S.A. 1/04 P/N 043-xxx Rev. A (PENDING)LIMITED WARRANTYLutron will, at its option, repair or replace any unit that is defective in materials or manufac-ture within two years after purchase. After the two year period, a pro-rated warranty appliesto this product until eight years after the purchase. For warranty service, return unit to placeof purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. For moreinformation regarding this warranty contact your Lutron representative.THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THEIMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PUR-CHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION,REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE,OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING ORINSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUEN-TIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUTOF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY,OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.This warranty gives you specific legal rights, and you may also have other rights which varyfrom state to state. Some states do not allow limitations on how long an implied warranty lasts,so the above limitation may not apply to you. Some states do not allow the exclusion or limi-tation of incidental or consequential damages, so the above limitation or exclusion may notapply to you.This product may be covered by one or more of the following U.S. patents:4,835,343; 5,736,965; 5,838,226; 5,848,054; 5,905,442; 5,982,103; D389,805; D404,013 andcorresponding foreign patents. U.S. and foreign patents pending. Lutron and HomeWorks areregistered trademarks and Illumination is a trademark of Lutron Electronics Co., Inc.© 2004 Lutron Electronics Co., Inc.Technical and Sales AssistanceIf you need assistance, call the toll-free LutronTechnical Support Center. Please provide exactmodel number when calling.(800) 523-9466 (U.S.A., Canada and the Caribbean)Other countries call:Tel: (610) 282-3800Fax: (610) 282-3090Visit our Web site at www.lutron.comTroubleshooting GuideSymptom Cause and ActionNo power available to unit.• If powered by the 9 V plug-in adapter, verify there ispower to the adapter.• If powered by the Hybrid Repeater Link, verify linkwiring.Repeater has not been addressed.• Address the repeater using the HomeWorks®IlluminationTM Software.No LEDs are illuminated on the Hybrid Repeater.Button presses on the Hybrid Repeater cause the STATUS LED on the repeater to flash rapidly.FCC InformationNote: This equipment has been tested and found to comply with the limits for a Class B digi-tal device, pursuant to Part 15 of the FCC rules. These limits are designed to provide rea-sonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed in accordancewith the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the inter-ference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the seperation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Caution: Changes or modifications not expressly approved by Lutron Electronics Co. couldvoid the user’s authority to operate this equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class Bdigital device, persuant to part 15 of the FCC rules.Operation is subject to the following:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may causeundesired operation.

Navigation menu