Lutron Electronics 0034 Lighting Control Transceiver User Manual hybRPTR

Download:
Mirror Download [FCC.gov]
Document ID	481501
Application ID	cccG/8d2DpQHgiFhTlPCLg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	60.9kB (761217 bits)
Date Submitted	2004-10-22 00:00:00
Date Available	2004-10-22 00:00:00
Creation Date	2004-09-22 20:45:43
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-09-23 09:18:40
Document Title	hybRPTR.qxd
Document Creator	PScript5.dll Version 5.2
Document Author:	rlau

Hybrid Repeater
Installation Instructions
HR-REP-120
120 V 60 Hz (9 V
Please Read Before Installing
300 mA adapter)
Overview
English
HomeWorks Hybrid Repeaters add RF capability to
HomeWorks processors configured with a Hybrid
Repeater Link and provide an additional coverage
area for radio frequency (RF) signals sent between
HomeWorks RF Dimmers/Switches, RF Keypads, and
RF Processors. Each repeater covers a sphere of
approximately 2500 square feet (232m2) of living
space. Up to five (5) repeating devices may be placed
in a HomeWorks RF system (a HomeWorks RF
Processor counts as one of the repeating devices).
Español
HR-REP-120
Français
Important Notes
Português
Codes: Install in accordance with all local and national electrical codes.
Power: The Hybrid Repeater can be powered from
EITHER of two sources:
1. Adapter power. Use only the adapter provided with the Hybrid Repeater (Lutron
model # T120-9DC-3-WH).
Caution - Using an adapter not rated at the
following specifications could damage the
repeater and possibly overheat the adapter.
• Input: 120 V 60 Hz
• Output: 9 V 300 mA
NEC Class 2; IEC PELV
2. Link power. Use only power supplied via a
HomeWorks Processor Hybrid Repeater
Link or a HomeWorks auxiliary power supply. (See section about the HWI-PS in the
HomeWorks Technical Reference Guide or
Application Note HW-104.) Each hybrid
repeater counts as 30 LEDs.
Note: An RF Processor does not supply
power on the Hybrid Repeater Link.
Environment: Ambient operating temperature:
32-104°F (0-40°C), 0-90% humidity, non-condensing.
Indoor use only.
Hybrid Repeater Wiring: Hybrid Repeater wiring
must be in a daisy chain configuration. The total
length of wire on the Hybrid Repeater Link may be up
to 1000 feet (305 m), and may contain up to five (5)
Hybrid Repeaters.
Cleaning: To clean, wipe with a clean damp cloth. DO
NOT use any chemical cleaning solutions.
Device Placement: HomeWorks Hybrid Repeaters
must be located within 30 feet (9 m) of the RF
Dimmers, Switches, and Keypads they are covering.
Hybrid Repeaters must also be within 60 feet (18 m)
of an RF Processor or another repeater when using
the RF Link for repeater-to-repeater or repeater-toprocessor communication. When using the Wired Link
for repeater-to-repeater or repeater-to-processor communication, a total wire length of 1000 feet (305 m)
may be used.
FCC Information
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, persuant to part 15 of the FCC rules.
Operation is subject to the following:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Installation
Wall Mounting
1. Find a suitable location for the Hybrid Repeater.
Hybrid Repeaters may be wall mounted using the
supplied wall bracket.
Place the repeater in a convenient and accessible
location. Note: Hybrid Repeaters must be within 60
feet (18 m) of an RF Processor or another repeater
when using the RF Link for repeater-to-repeater or
repeater-to-processor communication.
2. Connect Hybrid Repeater Link (if applicable).
3. Apply power to the Hybrid Repeater. If the
Hybrid Repeater is to be powered by the Hybrid
Repeater Link, apply power by turning on the
HomeWorks Processor. If the Hybrid Repeater is to
be powered by the plug-in adapter, insert the
adapter cord plug into the jack on the Hybrid
Repeater, then plug the adpater into a standard
wall receptacle.
Français
Español
English
Connect the Hybrid Repeater Link communication
wires from the HomeWorks® Processor (or previous
Hybrid Repeater in the daisy chain) to the terminal
block on the Hybrid Repeater (see Wiring
Diagram). Each terminal will accept up to three
22-18 AWG (0.5-1.0 mm2) wires.
Note: If using the plug-in adapter to power the
repeater, DO NOT connect the +15 V terminal
(terminal 2).
1. Attach wall bracket to wall using the supplied
screws and wall anchors.
UP
2. Place power cord into notches at top and bottom of
wall bracket. Wrap excess power cord around the
cord holder. Route Hybrid Repeater Link wiring
through hole in wall bracket and out through side
cutout. Align repeater and snap onto wall bracket.
Hybrid
Repeater Link
Wiring
Power Cord
UP
Português
STATUS and
TEST LEDs will
be dimly lit when
first powered
Plug in
power cord
and adapter
Operation
RF TX/RX LEDs
Indicate RF Link
activity.
WIRED TX/RX LEDs
Indicate Wired Link
activity.
Plug in
adapter jack
Wiring Diagram
HR-REP-120
(Side View)
MUX
MUX
+15 V
COM
STATUS Button
Used when addressing the
Hybrid Repeater from the
HomeWorks IlluminationTM
Software.
TEST LED
A slow flash indicates
RF communications
tests are in progress
STATUS LED
Indicates the status of the HomeWorks
system.
Note: When the Hybrid Repeater is
powered, but has not yet been assigned
an address from the HomeWorks
Illumination Software, the STATUS and
TEST LEDs will be dimly illuminated.
TEST Button
Activates RF communication
tests. To activate the tests,
press and hold the TEST
Button until the TEST LED
begins to flash.
Note: For communication tests,
the Hybrid Repeater,
HomeWorks Processor, and
other RF devices must first be
configured and addressed
using the HomeWorks
Illumination Software.
System Communications
RF Communications
RF Tabletop
Keypad
30 ft. (9 m) maximum
Hybrid Repeater
English
RF Dimmer
RF Keypad
Español
RF Processor
* Sta
1 2 3 4
60 ft. (18 m) maximum
between RF
Processors and
Repeaters, or between
Repeaters
Français
30 ft. (9 m) maximum
RF Communications Notes
• Hybrid Repeaters must be located within 30 feet (9 m) of the RF Dimmers/Switches and Keypads they are covering.
• Multiple repeaters may be necessary to provide adequate coverage. Up to four (4) repeaters may be used with each
RF Processor, and up to five (5) Hybrid Repeaters may be used with each 8 SeriesTM Processor or 4 SeriesTM
Processor (equipped with Hybrid Repeater Link).
Hybrid Repeater Link (Wired) Communications
HomeWorks® Processor
(8 Series shown)
RF Keypad
Hybrid Repeater
30 ft. (9 m)
maximum
Hybrid Repeater Link
1000 ft. (305 m) maximum
wire run distance
60 ft. (18 m)
maximum
Hybrid Repeater Link
1000 ft. (305 m) maximum wire run distance
Português
• Hybrid Repeaters must also be within 60 feet (18 m) of an RF Processor or another repeater.
Troubleshooting Guide
Cause and Action
No LEDs are illuminated on the Hybrid Repeater.
No power available to unit.
• If powered by the 9 V plug-in adapter, verify there is
power to the adapter.
• If powered by the Hybrid Repeater Link, verify link
wiring.
Button presses on the Hybrid Repeater cause the
STATUS LED on the repeater to flash rapidly.
Repeater has not been addressed.
• Address the repeater using the HomeWorks®
IlluminationTM Software.
Português
Français
Español
English
Symptom
FCC Information
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could
void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, persuant to part 15 of the FCC rules.
Operation is subject to the following:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Technical and Sales Assistance
If you need assistance, call the toll-free Lutron
Technical Support Center. Please provide exact
model number when calling.
(800) 523-9466 (U.S.A., Canada and the Caribbean)
Other countries call:
Tel: (610) 282-3800
Fax: (610) 282-3090
Visit our Web site at www.lutron.com
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in the U.S.A. 1/04 P/N 043-xxx Rev. A (PENDING)
LIMITED WARRANTY
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within two years after purchase. After the two year period, a pro-rated warranty applies
to this product until eight years after the purchase. For warranty service, return unit to place
of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage prepaid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. For more
information regarding this warranty contact your Lutron representative.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE
IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION,
REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE,
OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR
INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT
OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY,
OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.This product may be covered by one or more of the following U.S. patents:
4,835,343; 5,736,965; 5,838,226; 5,848,054; 5,905,442; 5,982,103; D389,805; D404,013 and
corresponding foreign patents. U.S. and foreign patents pending. Lutron and HomeWorks are
registered trademarks and Illumination is a trademark of Lutron Electronics Co., Inc.
© 2004 Lutron Electronics Co., Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:09:22 20:45:43Z
Modify Date                     : 2004:09:23 09:18:40-04:00
Page Count                      : 4
Creation Date                   : 2004:09:22 20:45:43Z
Mod Date                        : 2004:09:23 09:18:40-04:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : rlau
Metadata Date                   : 2004:09:23 09:18:40-04:00
Creator                         : rlau
Title                           : hybRPTR.qxd

EXIF Metadata provided by EXIF.tools