Lutron Electronics 0042 Radio Frequency Wireless Transmitter User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	763389
Application ID	eVP0hShSq30AQ5VBp+UZEw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.61kB (220126 bits)
Date Submitted	2007-02-28 00:00:00
Date Available	2007-02-28 00:00:00
Creation Date	2007-02-21 14:29:47
Producing Software	Canon iR5570/iR6570
Document Lastmod	0000-00-00 00:00:00
Document Title	Manual
Document Creator	Canon iR5570/iR6570

MAEéTDO Wirelessmz
Single-Pole Installation
Incandescent/Halogen Dimmer with RF Receiver
MFtF-GDD 120 v~ so Hz snow
Radio Frequency Wireless Tt'ansmitter with
One-Touch Favorite Button
MRF~VCTX sv= 1.5 mW
Important Notes
Please read before installing.
1. motion: To avoid overheating and poshrie damage to other equipment. do not
use to control receptacles, fluorescent lighting fixtures, motor-operated or
tr'anstonner-supplied appliances. .
2. Install in accordance with all national and local electrical codes.
3. When no “grounding means” exist within the wellbox then the NEG, 2005, Article
404-49 allows a dimmer without a grounding connection to be installed as a
replacement. as long as a plastic, noncombustible weliplale is used. For this type of
Installation, cap or remove the green ground wire on the dimmer and me an
appropriate wallplate such as Lutron‘s Clam. series wailpiates.
Do not paint Dimmers
Do not use where total lamp wattage Is less than 60 W or greater than 600 W (see
Dimmer Capacity Chart for details).
Operate between 0 “C (32 “fl and 40 “C (104 “F).
Dimmer may feel warm to the touch during normal operation,
Recommended walliiox depth is 2 1/2" (64 mm) mirilmum.
' clean (limiter with a sottdamp cloth my. Do not use any chemical cleaners
PPfl?’ P'P
This device complies with part 15 of the FCC Rules. Operation is subjecttothe following two
conditions: (1)Thls device may not cause handful interference and (Zt This device must
accept any interference received, includirg inlerterenoe that may cause undesired operation.
Multigang Installations
When imitating more than one control in the some wallbox, it may be necessary to
remove all imer side sections prior to wiring (see beiow). tiring pliers, bend side section
up and down until it breale oil. Repeat for each side section to be removed. Removal of
Dimmer side sections reduces maximum load capacity. Refer to the Dimmer Capacity
Chart below.
Each control has wining minim has trim
Inide serilon lid! sections mmd.
lelovud.
Dimmer Capacity Chart
[than Electmniix 0}. Inc.
LUTR N m...
3 coopecsbugmmmaeizeooss
Made and printed in the USA woo» P/N 777-77?
D'mmer Operation
Tap Button Options Dimming Roctrer
- Taponcevrhenunit'nolf-
Lights brighten smoothlyro Press to brighten
preset Intensity. Press to dill
- Tap once when riiit is on -
Lights rtlm simothiyto on.
- » - lEDs
0 To me I ~ L hts , > _
brighten ammonium; hum lever "acme
' Pressandlrnldwlrenunltk
- - Front Accessible
on — Each time dimmer is
one; Mr; rigging/{1.38 to OFF Service SWW‘
Gill a t .
IMPDI'I'l’AI" mill}:
button is held, the LEDs
begin to riasrrJne first llaehirg To replace bulk power may he
LED represents a to second muffin“)! will!“ W
lads to OFF. Each additional pulling the memo-n out on
flashing LED represents or the Dimmer.
additional to seconds or dehy For any procaine other
before lights Me to OFF (up to lhixl minim Irllllt
60 seconds of delay), replacement power must lie
, diaper-rooted at the main
electrical parrot
Radio Frequency Wireless
Transmitter Operation
important Notes
I. A Dimmer can team up to 4 Wear control Transmitters.
Z clean normal with a softdamp cram only. Do not use achemlcal cleaner.
3. Meets the Society otAutomotlve Engineers (SAE) temperature standards
-4o°c (40°F) to 113°C (235°F).
It. Do not paint the Visor Control
5. The range and performance of the Maestro Wireless system ls highly dependent on
a variety of complex teeters such as:
- Distance between system components
0 Geometry oi the home
0 Construction of walls separating system components
0 Electrical equipment located near system components
MI FuLl: OFF.
Tap once - Ilgivts brighten Tap once: Lights chm
rapidly to to! Intensity. smoothly to tilt.
FAVORITE BUTTON:
Tap once to recall your Iavorite light bretTo store ynurtevorite level, adjust rocker on
dimmer, press and hold favorite button for abouts seconds until the dmmer LED begins to
cycle quickly. won" is a valid preset level.)
This tianslltiflfi' is compatible with most HomeLink equipped Vetrides.
Ream see the manulacturer's instmrnions tor programming Inletmettono
"WES:
‘ - lire Dimmertsl must learn the Visor control Transmitter In order tor the Transmitter to
operate the Dimmerts).
- Bananas are included and are prelnstailed. Battery liletime is approximately 5 years.
Multiple Dimmer Applications
I‘i mrltiple Maesoo Wireless Dimmers are programmed to the same tmnsmittet they
will perform as lollows:
' Pressing the Oil FULL button will loose each dimmer to brighten to trill intensity,
regardless at whether some are on and some are off.
- Pressing the OFF button will cause all dimmers to hide oft.
- To Siva your favorite light level, adjust all the dimmers programmed to a transmitter
to the desired level. then press and hold the Favorite button tor about 8 seconds until
the dimmer LEDs begin to cycle quickly, Once your ievorite Iiglrt level is set, pressing
the Favoltle button will cause each dimmer to return to your favorite light level.
' System Expansion: Each transmitter can control up to 4 dimmers.
Eon dimmer can learn on to 4 transmitters.
Battery Replacement
The RodiaFrequemry Vlfireiess Tmnsmitter uses (2) CR2032 Lithium Coin cell 3.0 V each
betmries that are ore-installed.
To replace batteries: /
1. Remove 3 screws on back. ,
2. Remove back cover.
3. Slide out both coin oell batteries.
4. Replace with CR2032 IJthlum
Odin Cell 3.0V each.
5. Replace back cover.
5. Replace 3 screws on back.
Visor Control Mounting
The Visor Control Transmitter can be mounted to a vehicle’s
visor using the supplied visor clh.
Attach visor clip 3
to Visor Control '
04
(m
04
(s.
o-
o-
Mount Visor Control
onto vehicle’s visor. ‘
[39 ~ fl
Visor clip may need to be manuaily opened dependin
on visor llickness.
For: Information
"mt: This equipment has been tested and Iounrt to comply with the limits for it Goes B
dlytal device, pursuant to part is more FCC mles.fltese limits are designed to provide
reasonable protection against harrntui Interterence in a residential installation. This
equipment generates. uses and can radiate radio frequency energy and. it not installed and
used in accordance with the lnstructlmis, may cause harmful interference to radio and
television reception. which cai'r be determined bytumlng the equipment otf and on. The user
Is encourmed to try to correct the interference by one or more at the following measures:
- Realism or relocate the receiving antenna.
- Inueme the separation between the equipment and receiver.
- Connect the equipment into an orillet on a circuit dlfierent trom that to which the
recener is connected.
- Consuh the dealer or an experienced radio/TV technician tor help
coirtton: changes or modifications not expressly approved by Luiron Electronics Co. could
void the user's authority to operate this equipment.
Technical Assistance
II you have questions concerning the installation or operation oftfls product,
cal the Lotion Milka! support center. Please provide exact model number
when calling.
@r use and Donada mhrsfldoye)
1-800-523-9466
other connotes 8am - 8pm ET
Hero-mom
Limited Warranty
(viii! only in USA" Gallidi, mm Rico, Ind the hrlhbclth)
Loom wilt-i newton, react or notice my normal is detective in maisrhlsor rrirrririacnn within one year
51W pitchase. RI WNW service, return Ill_t to piece 01 Moira: or mail to Linton at 7200 son Rd,
cooperating. RA "meme. piretxoe prepaid.
tilts wunimrtts II List or on men ExPnExs NAMES. Alto tlE lumen vuinnurnr OF
IlBIBIIAII'ITtlIJTY is unmet to one run more HIMASEI’IIS mommy nos not men I'IIE
cost or institution, narrow. in RHIEIIUJITDIV, on name: newmrrli Hint! mantles,
on cum! Fndrll unmomt more on thstAuJomi. nits modem noes norcovflunclisim
Oil “WEN". MINES. urmorrs LIABILITY flIIAltVMM FDRIIAIMMARISIIIEWTDFDR ll
Willlfiil'ml WITII TIE HANWAGWRE SALE, mm, IIELIiIEW. OR USE OFTIIE IIIIT Slim
"EVE! NEE) TIE PUMIIASE PIIIH OF THE IIIIIT.
This wmomy giveewll spen'fic legal rights. andyw only into otter rights which vii/item Qateto shire. some
states on pit aiirm the emoticon or limitation of ridden! or consequential arrayed, or limitation on him long
an rmmwnrwnoylastwmahmlrmmsMMamymm
This product Is covered Intisf one or more of ma “1an us. patents: 0,835,348; assets: 5,390,940;
5,537,960; 5,900,057; 5,169,377; 5,900,72’, SMILES: (£163,796; and mrrcspomiu heign patina. us, aid
iordgn patents wndim.l.utron.ciaro, Mano, and Maem wireless are registered transports and finish; a
Iredeniaik of Loom Emile co, the NE is B misc!“ MUM oi the National m Prmewon mom,
OW. MEETING.
® 2006 Ltllloil Elechmice in. Int:.
777-777
@ Fox +1-aio-2ez-aoeo
Q tiltp:llwww.lutron.com
Installation
Turning Off Power.
' Tirrn power OFF at ciiuiit breaker (or remove toss).
Removing Wallplate and Switch.
- Remove the wallplate and switch mounting screws.
- (awfully remove switch hem wen (do not remove wires).
H A hanger: Verity prmerto
‘ switch ls UFF belore
proceeding.
El Disconnecting Switch Wires.
Imporhrt Note:
this wall swoon may have twowires attached to the me screw (see ntrrelrattons below tor
I). Tape these two wires together belrxe dIeoorrrroeflnp. When wlr’rrg, connect wine in
the Drmmerrhe some way they were connected tome switch.
One we in it.-
premium-minor
and now do the
mm.
on. eorrfimw:
win to on wivw.
Se.“ Tami-unis: Push-in mire»; Lower! w“:
him straw! h bin-t. linen sacrum". Pill Tum sum to louewlt
who out.
Removing Wallplat
' Dimmer has a stalled Lutmri cimwellpla‘le. Remove the weilplate beiore
proceeding with installation. Thk will expose mounting l‘llilES in adapter, and prevent
wallplate damage wirle Infialflng.
Gust: cram warrpraru it
top and mi forward to
remove.
Lutron Technical Support Center 1-800-523-9466 24 hrs / 7days wwvrnlutron.com
important W 9 information
When makiro wire mnnentlons. followtlie recommended strip lengths and combinations lortrie
supplied wire cmnector. Note: All wire eonneetore pnwlded are suitable for copper wire only. For
aluminum wire, eonsull an electrrrx‘dn. Trim or strip wallbuxwires to the length indicated by the
Programming
Adding Transmitter to Dimmer
strip genoe on the backolttre dimmer Prss and hold the «mere biggie onion-no press mo notion toggle
button mic amino and holding the Oil
mm on transmitter.
bitten LEDs will blink rmrvioiraliy
Ptrsli-ln'l'lmfllllh: ltlllilvrhsfilly» m the mm,“ W ("trump
Marin "ME: PllSh-Interrrririesmlixlsemlllu
Wlll ounneuor. Ofllllledflf AWE mildmprzmm m on not use Motrin ltmriamt
Uselo ioiir "minor liom. stranded mhlfs‘ied wire. TM" "is EDS V4" MW
izrwogmonowrre on memo-noon
to tame dinner Screw l'ermlruk: nation manly. WW" WWW“ "Wt
mom. mmrnosoreroneemonzom
Awe saflduapperwrrr only. on our use
stranded worsen“ rm.
Wiring m once the dimmer Ieamsttremsmmrs momsAheLEDs on the emu-awn cydewlckty
. . . rr .
- For Installations lnvolvrnp more than one control in a wailbox, refer to am mm mm “Gleam!" “Mammy“ mm" mm
Mulogang Installations before beginning. mflkmwum "7h” mm” “mm
you mar in program the Transmitter in.
Wiring tire Dimmer:
- list the wire omnector mvided, .
mm, the 9mm ”Madam“, me Setting the Favorite button on the Transmitter
Dimmer to the bare Miter or oreen E NOTE: Tr'anstmtter must be sorted to dimmer helore you can set the Favorite.
ground wire in the Wallbox. Do not
connect it to any miter wire. (See E NOTE: ll Transmitter is added to multiple dimmers, you roost adjust each dimmer
lim before you set the Favorite binton (minty creating a seene).
Important Note 3.) m r MM
. Connect either of the wires removed from m roti'imo amwmwwmfim mm
the swimh to one ofthe limes screw the Isles Iowerrwker
terminals on the Dimmer, or insert lully
Into the ptlSi‘Hll terminal.
. Comeettlre remairlng wire remwed from
the switrrlr to the other has screw
um terminal on the Dimmer, or insert idly into
51." the push—in terminal.
NOTE: unremeavaomnrmmrmaem E mmmm_menaumrre
new
minislsaslngle pole oonlrol. For3-way ’” m” WNW“ “mm “mmmm‘mmw
application (2 switch control for one light), Monomer-ninja seem-defile LEJs wlll were down an on lights
special order MRF—Sosr will quinine new moors iinrrt level.
n Monmouth",
Mounting Dimmer to Wallbox. TmUbleShOOting mmwmmmmm
- Form wires careiully into the wallbox, mount and align Dimmer. Symptom Possible (Farm —1
' Replaoe Clam “mm“ ngirt does not trrrn ON or - FrontAoceesible Service Switch (5435) all
no LEDs lrirrr DNA Dimmer is pulled mitt» the OFF position.
err-p onvmlntm - Light bulb(s) hunted out.
Align atrium mo
damn um
- Breaker is OFF or tripped.
fiWidng error. M Lotion mounted-Emmott
L‘enierat +1—800-52i-9466.
Light does not respond to - Dimmer failed to learn Transmitter address, see
Radio Frequency Wireless programming.
Transmitter 0 Transmitter batteries irelalled incorrectly.
- Transmitter batteries are dead.
- Transmitter outside operating mnge.
- Dimmer has atready reoeirmd and responded to
command.
Turning On Power.
' Tum power on at circuit breaker (or replace fuse).
Dimmer keeps turning 0M - Load is less than 60 w
and OFF.
LEDsi and 7 blink - Maximum number oiTransmitter addresses have
alternately. been programmed to Dimmer.
- Remove another Transmitter address.
~ limet iaclory default (removes all Transmitter
addresses in dimmed.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Creator                         : Canon iR5570/iR6570
Create Date                     : 2007:02:21 14:29:47-05:00
Author                          : 
Producer                        : Canon iR5570/iR6570
Title                           : 
Subject                         : Image

EXIF Metadata provided by EXIF.tools