Lutron Electronics 0053 Electronic dimmer/switch with RF communication User Manual
Lutron Electronics Company Inc Electronic dimmer/switch with RF communication
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 972770 |
| Application ID | +aBM6bNN94j+toosuWTcEw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 19.43kB (242926 bits) |
| Date Submitted | 2008-07-18 00:00:00 |
| Date Available | 2008-07-18 00:00:00 |
| Creation Date | 2008-06-24 11:23:05 |
| Producing Software | Adobe PDF Library 7.0 |
| Document Lastmod | 2008-06-24 11:23:25 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS2 (4.0.5) |
StanzaTM StanzaTM Dimmers SZ-6D, SZ-6ND StanzaTM Switch SZ-6ANS Installation Instructions 120 V Please Read Before Installing Dimmer and Dimmer with Neutral Switch Load Specifications Control Load Type Min. Load Max. Load Incandescent 50 W 600 W MLV2 50 W / VA 450 W / 600 VA SZ-6D Incandescent 10 W 600 W MLV2 10 W / VA 450 W / 600 VA Lighting 10 W / VA 6A Motor 0.083 A 3A SZ-6ND SZ-6ANS3 Notes 1D immer Load Type: SZ-6D and SZ-6ND are designed for use with permanently installed incandescent, magnetic low-voltage (MLV), or tungsten halogen only. Do not install dimmers to control standard receptacles or motor-operated appliances. 2 Low-Voltage Applications: Use SZ-6D and SZ-6ND with magnetic (core and coil) low-voltage transformers only. Not for use with electronic (solid-state) low-voltage transformers. Operation of a low-voltage circuit with lamps inoperative or removed may result in transformer overheating and premature failure. Lutron strongly recommends the following: •D o not operate low-voltage circuits without operative lamps in place. •R eplace burned-out lamps as quickly as possible. •U se transformers that incorporate thermal protection or fused transformer primary windings to prevent transformer failure due to overcurrent. 3 Switch Load Type: SZ-6ANS is designed for use with all permanently installed lighting loads and with motor loads up to 1/4 HP (5.8 A). 50 / 60 Hz Important Notes Multigang Installations Install in accordance with all local and national electrical codes. Caution! These controls must not be used to control equipment that is not visible from every control location. They must also not be used to control equipment that could create hazardous situations such as entrapment if operated accidentally. Examples of such equipment which must not be operated by these controls include (but are not limited to) industrial doors, microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable equipment is connected to these controls. Environment: Ambient operating temperature: 32 to 104 °F (0 to 40 °C), 0 to 90% humidity, non-condensing. Indoor use only. Spacing: If mounting one control above another, leave at least 4½ in. (114 mm) vertical space between them. Faceplates: Use Lutron Stanza faceplates for best color match and aesthetic appearance. Do not paint controls or faceplates. Cleaning: To clean, wipe with a clean damp cloth. Do not use any chemical cleaning solutions. Wallboxes: Lutron recommends using 3½ in. (89 mm) deep wallboxes for easier installation. Several controls may be installed in one multigang wallbox — see Derating Chart. RF Device Placement: RF dimmers and switches must be located within 20 feet (6 m) of an RF signal repeater or a device configured as a repeater. Stanza RF dimmers or switches cannot be controlled by the system until they are addressed and programmed. They will work as stand-alone controls only. In multigang installations, several controls are grouped horizontally in one multigang wallbox. When combining controls in a wallbox, derating is required. Control Location for Ganging Derating Chart Control SZ-6D, SZ-6ND SZ8ANS Load Type End of Gang Middle of Gang Incandescent 500 W 400 W MLV 400 W / 500 VA 300 W / 400 VA Lighting 5A 3.5 A Motor 3A 3A Middle of gang Installation Caution! Locate and remove fuse or lock circuit breaker in the OFF position before proceeding. Wiring with power ON may result in personal injury or death. Short Circuit Check: Check the installation for short circuits before installing control(s). With power OFF, install standard mechanical switch(es) between hot and load. Restore power. If lights do not work or a breaker trips, correct wiring and check again. Install control(s) only when short is no longer present. Warranty is void if control is turned ON with a shorted circuit. 1. T urn power OFF at fusebox or circuit breaker. 2. P repare wires. When making wire connections, follow the recommended strip lengths and combinations for the supplied wire connector. Note: Wire connectors provided are suitable for copper wire only. Wire Connector: • Strip insulation 3/8 in. (9.5 mm) for #14 AWG (1.5 mm2) wire • Strip insulation 1/2 in. (12.7 mm) for #16 or 18 AWG (1.0 mm2 or 0.75 mm2) wire • Use to join one #14 AWG (1.5 mm2) or #12 AWG (2.5 mm2) ground wire with one #18 AWG (0.75 mm2) control ground wire. Twist wire connector tight. Trim or strip wallbox wires to the length indicated by the strip gauge on the back of the control. Mounting Diagram Faceplate adapter mounting screws FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may not cause harmul interference, and (2) this device must accept any interference received, incouding interference that may cause undesired operation. End of gang Wallbox Included: Control mounting screws Control Wire Connector (1) Mounting Screws (2) Faceplate/adapter purchased separately. Push-In Terminals: Insert wires fully. Push-in terminals are for use with #14 AWG (1.5 mm2) solid copper wire only. DO NOT use stranded or twisted wire. OR Screw Terminals: Tighten securely to 5 in-lbs (0.55 N•m). Screw terminals are for use with solid copper wire only. DO NOT use stranded or twisted wire. 3. W ire controls as follows: Single location installation: See Wiring Diagrams 1 and 2. Power Booster and Interfaces: When using power boosters or interfaces, see wiring diagrams provided with the interface. 4. Push all wires back into the wallbox and loosely fasten the control to the wallbox using the control mounting screws provided. Do not pinch the wires. 5. Attach Lutron Stanza faceplate adapter and faceplate. a. Install faceplate adapter onto front of control(s). b. Tighten control mounting screws until faceplate adapter is flush to wall (do not over-tighten). c. Snap faceplate onto faceplate adapter, and verify that control is aligned properly. d. If control(s) is (are) misaligned, loosen mounting screws appropriately. 6. Restore power. Check for correct local operation (see Dimmer Operation and Switch Operation). Wiring Diagram 1 Single Location Installation SZ-6D Dimmer/Switch Brass Hot/Live Black 120 V 50 / 60 Hz Green Troubleshooting Guide Symptom Cause and Action Load is off and there is no indicator on the dimmer/switch Power not present • Circuit breaker OFF or tripped. Perform short circuit check. • F ASS is in the OFF position. Move FASS to the ON position by fully pushing it up. Lighting load Wiring error • Check wiring to be sure it agrees with installation instructions and wiring diagrams. Ground Neutral Lamps burned out or not installed • Replace or install lamps. Wiring Diagram 2 Single Location Installation with Neutral SZ-6ND, SZ-6ANS Dimmer/Switch Hot/Live Dioded lamps • Replace with non-dioded lamps. Damaged dimmer/switch • Device may have been damaged by previous overload or miswire. Replace device. Brass Silver Black 120 V 50 / 60 Hz Green Load Ground Dimmer / switch indicator is on but load cannot be turned on and/or cannot be turned off Wiring error • Check wiring to be sure it agrees with installation instructions and wiring diagrams. Light turns ON and OFF continuously Load is less than minimum load requirement • Make sure the connected load meets the minimum load requirement for that control. See Load Specifications table. Neutral Dimmer Operation (SZ-6D, SZ-6ND) Dimming Slider Slide up to brighten; slide down to dim Load must be on for slider to affect intensity Indicator light in slider track Glows softly for easy locating of control Track ends flash amber to indicate programming/ addressing mode Improper load type • Check that the load being dimmed is not non-dimmable. See Load Specifications table. Lights don’t switch ON/ OFF from keypad Switch Operation (SZ-6ANS) Indicator light in slider track Glows softly for easy locating of control Tapswitch Turns load on and off FASSTM Front-accessible service switch (facilitates safe bulb replacement) Pull down to remove all electrical power from load and deactivate switch Push up to restore power to load and switch Improper programming • Check programming in the Stanza software. Out of RF range • Ensure device is within 20 feet (6 m) of another device configured as a repeater. Tapswitch Turns load on to slider level and off FASSTM Front-accessible service switch (facilitates safe bulb replacement) Pull down to remove all electrical power from load and deactivate dimmer Push up to restore power to load and dimmer Damaged dimmer/switch • Device may have been damaged by previous overload or miswire. Replace device. Wiring • Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagrams. Faceplate is warm Solid-state control dissipation • Solid-state dimmers and switches internally dissipate about 2% of the total connected load. It is normal for dimmers and switches to feel warm to the touch during operation. Control is buzzing or humming It is normal for dimmers and switches to emit a slight buzzing or humming sound. Returning the Dimmer/Switch to Notes Factory Settings •R eturning to factory settings will clear 1. Triple-tap the tapswitch quickly (within all programming from the dimmer/ 1 second). switch, and will prevent it from being controlled over RF from a keypad or 2. Press and hold the tapswitch for 5 control interface. seconds (until the load flashes) . fter being returned to factory defaults, 3. Triple-tap the tapswitch quickly again. • A the device will need to be re-addressed as part of a system. Lamp Replacement Caution! For any procedure other than routine lamp replacement, power must be disconnected at the main electrical panel. Working with power ON may result in personal injury or death. For routine lamp replacement, remove power from the fixture(s) by pulling down the FASS switch on the Dimmer / Switch. Technical support: U SA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 Central/South America: +1.610.282.6701 Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with 8-year pro-rated parts replacement on commissioned systems. These products may be covered under one or more of the following U.S. patents: 5,248,919; 5,637,930; 5,838,226; 5,848,054; 5,905,442; 6,687,487; 6,803,728; and corresponding foreign patents. U.S. and foreign patents pending. Lutron and the sunburst logo are registered trademarks and FASS and Stanza are trademarks of Lutron Electronics Co., Inc. © 2008 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. Made and printed in the U.S.A. P/N 030-994 Rev. A 6 /08
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1.1-111 Instance ID : uuid:43814d8a-9b70-4948-a9a9-2856fe5b424e Document ID : adobe:docid:indd:192b05e9-3237-11dd-b82a-ac4c19f22906 Rendition Class : proof:pdf Derived From Instance ID : 192b05e8-3237-11dd-b82a-ac4c19f22906 Derived From Document ID : adobe:docid:indd:c74e7684-3232-11dd-b82a-ac4c19f22906 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 300.00, 72.00 Manifest Placed Y Resolution : 300.00, 300.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches Manifest Reference Instance ID : uuid:475B50F8A33D11DC9AE4F26D9E047CA8, uuid:2711D17DA33D11DC9AE4F26D9E047CA8, uuid:6081411C76C5DA11BDC9A93607A846D6 Manifest Reference Document ID : uuid:2711D182A33D11DC9AE4F26D9E047CA8, uuid:2711D17CA33D11DC9AE4F26D9E047CA8, uuid:5F81411C76C5DA11BDC9A93607A846D6 Create Date : 2008:06:24 11:23:05-04:00 Modify Date : 2008:06:24 11:23:25-04:00 Metadata Date : 2008:06:24 11:23:25-04:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 11408 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools