Lutron Electronics 0065 Modular RF transmitter and lighting controller for assemble with Lutron lighting controllers User Manual

Lutron Electronics Company Inc Modular RF transmitter and lighting controller for assemble with Lutron lighting controllers

User Manual

WirelessRProgramming AddendumLUTRONThis addendum applies to the GRAFIK Eye QS Wireless models listed below, and their associated components.QSGRJ-3PQSGRJ-4PQSGRJ-6PQSGRK-3PCEQSGRK-4PCEQSGRK-6PCEQSGRJ-6EQSGRJ-8EQSGRJ-16EContentsAssociating GRAFIK Eye QS Wireless Control Units................................................2Associating Wireless Occupancy Sensors and GRAFIK Eye QS Wireless Control Units . . . . . . . . . . . . . . . . . . . . 3Associating Sivoia® QS Wireless Shades/Drapes and GRAFIK Eye QS Wireless Control Units. . . . . . . . . . . . . . . . 4Associating PicoTM Wireless Controls and GRAFIK Eye QS Wireless Control Units: Zone Control. . . . . . . . . . . . . . 5Associating PicoTM Wireless Controls and GRAFIK Eye QS Wireless Control Units: Scene Control. . . . . . . . . . . . . 6Wireless Mode............................................................................7Contact Information ........................................................................8FCC Information Changes or modifications not expressly approved by Lutron Electronics Co. could void the user's authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may not cause harmul interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential and commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the seperation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Wireless System ProgrammingRGRAFIK Eye® QS Wireless System Programming 2OK1 2 3 4 5 6OK1 2 3 4 5 6GRAFIK Eye QS A“Talks” to GRAFIK Eye QS B; scene activation and master (raise/lower) button presses activated on unit A are replicated on unit B.GRAFIK Eye QS B“Listens” to GRAFIK Eye QS A; unit B replicates scene activations and master (raise/lower) button presses on unit A.When there is more than one GRAFIK Eye QS control unit in a wireless system, it is often convenient to associate them so that scene activations and master (raise/lower) button presses carry over to other associated GRAFIK Eye QS control units.To associate two GRAFIK Eye QS control units:1. Begin with the GRAFIK Eye QS control unit that will “talk” (button presses will be replicated on the other control unit; in the drawing below this is GRAFIK Eye QS A). Press and hold the top and bottom scene buttons until the LEDs flash (about 3 seconds).2. Continue with the GRAFIK Eye QS control unit that will “listen” (replicate button presses on the other control unit; in the drawing below this is GRAFIK Eye QS B). Press and hold the top scene button until the LEDs flash (about 3 seconds).3. Return to the GRAFIK Eye QS control unit that will “talk” (A). Press and hold the top and bottom scene buttons until the LEDs stop flashing (about 3 seconds).4. It is often desired to repeat the process in reverse so that GRAFIK Eye QS B talks to GRAFIK Eye QS A.To disassociate two wireless GRAFIK Eye QS control units:Simply repeat the association steps, in the same order; press and hold the bottom scene button on B to disassociate.Note: The wireless signal has a range of 30 feet (10 m) through standard construction.Associating GRAFIK Eye QS Wireless Control UnitsOK1 2 34569 10 11 12 13 14 7815 169-161-8On the unit that will “talk”, press and hold the top and bottom scene buttons for 3 seconds to begin or end association or disassociation with the unit that will “listen”.OK1 2 34569 10 11 12 13 14 7815 169-161-8On the unit that will “listen”, press and hold the top scene button for 3 seconds to associate, or press and hold the bottom scene button for 3 seconds to disassociate with the unit that will “talk”.AssociateORDisassociate
Wireless System ProgrammingRGRAFIK Eye® QS Wireless System Programming 3OK1 2 3 4 5 6Wireless Occupancy Sensor“Talks” to GRAFIK Eye QS control unit, activating scenes on the GRAFIK Eye QS.Lutron’s wireless Radio Powr SavrTM occupancy and vacancy sensors can be associated with the GRAFIK Eye QS Wireless to activate scenes when occupancy or vacancy is detected.To associate wireless occupancy sensors and GRAFIK Eye QS control units:1. Press and hold the “Lights On” and “Lights Off” buttons on the front of the occupancy/vacancy sensor simultaneously until the lens starts flashing (about 3 seconds).2. Press and hold the top scene button of the GRAFIK Eye QS Wireless control unit until the LEDs flash (about 3 seconds).3. Return to the occupancy sensor. Press and hold the “Lights On” and “Lights Off” buttons simultaneously until the lens stops flashing (about 3 seconds).To disassociate wireless occupancy sensors and GRAFIK Eye QS control units:Simply repeat the association steps, in the same order; press and hold the bottom scene button on the GRAFIK Eye QS to disassociate.Note: The wireless signal has a range of 30 feet (10 m) through standard construction.Associating Wireless Occupancy Sensors and GRAFIK Eye QS Wireless Control Units On the wireless occupancy sensor, press and hold the “Lights On” and “Lights Off” buttons for 3 seconds to begin or end association or disassociation with the GRAFIK Eye QS control unit.Note: Pressing the “Lights On” button initiates the “occupied” scene programmed on the GRAFIK Eye QS control unit. Pressing the “Lights Off” button initiates the “unoccupied” scene programmed on the GRAFIK Eye QS control unit. Before the GRAFIK Eye QS is programmed, the “Lights On” button may not produce an action. Refer to the Installation manual for the GRAFIK Eye QS to program desired scenes.OK1 2 34569 10 11 12 13 14 7815 169-161-8On the GRAFIK Eye QS control unit, press and hold the top scene button for 3 seconds to associate, or press and hold the bottom scene button for 3 seconds to disassociate with the occupancy sensor.AssociateORDisassociateGRAFIK Eye QS Control Unit“Listens” to wireless occupancy sensor, so that the occupancy sensor activates scenes on the GRAFIK Eye QS.Lens
Wireless System ProgrammingRGRAFIK Eye® QS Wireless System Programming 4When a GRAFIK Eye QS wireless system consists of Sivoia QS shades (or drapes) and a GRAFIK Eye QS with one or more shade button groups, you can associate the shade button groups on the control unit with the shades/drapes so the shade buttons can directly control the shades/drapes.To associate wireless GRAFIK Eye QS shade buttons and Sivoia QS shades/drapes:1. On the GRAFIK Eye QS shade button group you want to control the shades/drapes, enter programming mode: Press and hold the top (open) and bottom (close) buttons for 3 seconds. The top and bottom LEDs will flash.2. The LEDs on the electronic drive unit (EDU) and the wireless antenna of unassociated shades/drapes will blink slowly. On the shade/drape that you wish to associate with the shade button group, tap any button; the LED on the EDU will blink rapidly to indicate the shade is now associated with the shade button group on the GRAFIK Eye QS.3. Repeat step 2 to associate additional shades/drapes to that shade button group.4. Exit programming mode: Press and hold the top (open) and bottom (close) buttons for 3 seconds. The top and bottom LEDs will stop flashing.5. Repeat steps 1 through 4 for additional shade button groups, as applicable.To disassociate wireless GRAFIK Eye QS shade buttons and Sivoia QS shades/drapes:1. On the GRAFIK Eye QS shade button group you want to disassociate shades/drapes from, enter programming mode: Press and hold the top (open) and bottom (close) buttons for 3 seconds. The top and bottom LEDs will flash.2. On the electronic drive unit (EDU) of the shades/drapes that you wish to disassociate from this shade button group, tap any button; the green LEDs on the EDU and antenna will blink slowly to indicate the shade is disassociated from the shade button group on the GRAFIK Eye QS.3. Repeat step 2 to disassociate additional shades/drapes from that shade button group.4. Exit programming mode: Press and hold the top (open) and bottom (close) buttons for 3 seconds. The top and bottom LEDs will stop flashing.5. Repeat steps 1 through 4 for additional shade button groups, as applicable.To store shade/drape presets on a wireless GRAFIK Eye QS shade button group:The shade/drape must already be associated with the shade button group.1. Use the raise/lower buttons on the GRAFIK Eye QS shade button group to position the shades/drapes at their desired preset level.2. Press and hold the preset button of the shade button group for 3 seconds. The LED next to the button will flash, then turn on, indicating the preset is stored.Note: The wireless signal has a range of 30 feet (10 m) through standard construction.Associating Sivoia® QS Wireless Shades/Drapes and GRAFIK Eye QS Wireless Control Units Press and hold the top (open) and bottom (close) buttons on the GRAFIK Eye QS shade button group to enter or exit programming mode.OK1 2 3 4 5 6OpenPresetClosePress and hold the preset button for 3 seconds to store a preset on the GRAFIK Eye QS shade button group.OK1 2 3 4 5 6OpenPresetCloseShade EDULED
To use the Pico wireless controller as a zone controller with a GRAFIK Eye QS Wireless control unit:1. On the Pico, press and hold the top (on) and bottom (off) buttons for 3 seconds. The LED on the Pico will flash slowly, and the scene buttons LEDs on the GRAFIK Eye QS will all flash.2. On the GRAFIK Eye QS, the info screen will ask for confirmation that you wish to change the type; press the OK button. Use the master buttons on the GRAFIK Eye QS to select “Zone”. Press OK to save.3. To assign a zone on the GRAFIK Eye QS to the Pico, use the zone raise/lower buttons for that zone to set the desired preset level, then press and hold the zone raise and lower buttons simultaneously for 1 second (until the LEDs flash at the programmed preset level). To unassign a zone on the GRAFIK Eye QS to the Pico, while the zone LEDs are flashing, press and hold the zone raise and lower buttons simultaneously for 1 second (until the LEDs stop flashing and the 3 middle LEDs light). Repeat this step to assign levels for all desired zones to the Pico control. Zones assigned to the Pico will have all LEDs flashing in unison, and zones not assigned will have the 3 middle LEDs lit.4. On the Pico, press and hold the top (on) and bottom (off) buttons for 3 seconds. The LED on the Pico and the LEDs on associated GRAFIK Eye QS Wireless control units will stop flashing.Functionality of the Pico control when programmed as a zone controller:Top button: All assigned zones go to 100%Center round button: All assigned zones go to the programmed preset levelBottom button: All assigned zones go to OffNote: The wireless signal has a range of 30 feet (10 m) through standard construction.Wireless System ProgrammingRGRAFIK Eye® QS Wireless System Programming 5LightOnAdjustOffChange type?Zone SavedSavedPicoChange type?Press OKOK1 2 34569 10 11 12 13 14 7815 169-161-8On the GRAFIK Eye QS control unit, press and hold the top scene button for 3 seconds to associate, or press and hold the bottom scene button for 3 seconds to disassociate with the Pico control.AssociateORDisassociateInfo screenAssociating PicoTM Wireless Controls and GRAFIK Eye QS Wireless Control UnitsOK1 2 34569 10 11 12 13 14 7815 169-161-8Zone LEDsZone RaiseZone Lower
When a GRAFIK Eye QS wireless system includes a Pico wireless control, you can use the Pico wireless control as either a scene controller or a zone controller. This page describes using the Pico wireless control as a scene controller; the previous page describes using it as a zone controller.To use the Pico wireless control as a scene controller with a GRAFIK Eye QS Wireless control unit:1. On the Pico, press and hold the top (on) and bottom (off) buttons for 3 seconds. The LED on the Pico will flash slowly, and the scene button LEDs on the GRAFIK Eye QS will all flash.2. On the GRAFIK Eye QS, the info screen will ask for confirmation that you wish to change the type; press the OK button. Use the master buttons on the GRAFIK Eye QS to select “Scene”. Press OK to save.3. To associate the GRAFIK Eye QS with the Pico, press and hold the top scene button on the GRAFIK Eye QS for 3 seconds (until the LEDs all flash). To disassociate the GRAFIK Eye QS with the Pico, press and hold the bottom scene button on the GRAFIK Eye QS for 3 seconds (until the LEDs stop flashing).4. On the Pico, press and hold the top (on) and bottom (off) buttons for 3 seconds. The LED on the Pico and the LEDs on associated GRAFIK Eye QS Wireless control units will stop flashing.Functionality of the Pico control when programmed as a scene controller:Top button: Scene 1Center round button: Scene 16Bottom button: OffNote: The wireless signal has a range of 30 feet (10 m) through standard construction.Wireless System ProgrammingRGRAFIK Eye® QS Wireless System Programming 6LightOnAdjustOffChange type?Scene SavedSavedPicoChange type?Press OKOK1 2 34569 10 11 12 13 14 7815 169-161-8On the GRAFIK Eye QS control unit, press and hold the top scene button for 3 seconds to associate, or press and hold the bottom scene button for 3 seconds to disassociate with the Pico control.AssociateORDisassociateInfo screenAssociating PicoTM Wireless Controls and GRAFIK Eye QS Wireless Control Units
Wireless System ProgrammingWireless Mode By default, the GRAFIK Eye QS Wireless control unit’s wireless feature is in Setup Mode. In this mode, the GRAFIK Eye QS Wireless control unit will respond to any programming commands from other nearby Lutron QS wireless (and compatible) products. After associating other wireless devices to the GRAFIK Eye QS Wireless, you may wish to prevent additional devices from communicating with it. To do this, change the wireless mode to “Locked Mode”.1. Press and hold the top and bottom scene buttons to enter programming mode (see illustration at right).2. Use the master buttons to highlight “Wireless Mode” and press the OK button to accept.3. Use the master buttons to highlight “Locked Mode” and press the OK button to accept.4. The info screen will display a confirming “Saved” message.5. Press and hold the top and bottom scene buttons to exit programming mode.Wireless ModeLocked ModeSavedSavedMain menuShade labelsWireless ModeOK1 2 34569 10 11 12 13 14 7815 169-161-8Master buttonsOK buttonPress and hold the top and bottom scene buttons to enter or exit programming mode.GRAFIK Eye® QS Wireless System Programming 7R
WirelessRProgramming AddendumContact InformationInternet: www.lutron.comE-mail: product@lutron.comWorld HeadquartersUSALutron Electronics Co., Inc.7200 Suter Road, Coopersburg, PA 18036-1299TEL +1.610.282.3800FAX +1.610.282.1243Toll-Free 1.888.LUTRON1Technical Support 1.800.523.9466North and South America Technical HotlinesUSA, Canada, Caribbean: 1.800.523.9466Mexico: +1.888.235.2910Central/South America: +1.610.282.6701European HeadquartersUnited KingdomLutron EA Ltd.6 Sovereign Close, London, E1W 3JF United KingdomTEL +44.(0)20.7702.0657FAX +44.(0)20.7480.6899FREEPHONE (UK) 0800.282.107Technical support +44.(0)20.7680.4481Asian HeadquartersSingaporeLutron GL Ltd. 15 Hoe Chiang Road, #07-03 Euro Asia Centre, Singapore 089316TEL +65.6220.4666FAX +65.6220.4333Asia Technical HotlinesNorthern China: 10.800.712.1536Southern China: 10.800.120.1536Hong Kong: 800.901.849Indonesia: 001.803.011.3994Japan: +81.3.5575.8411Macau: 0800.401Singapore: 800.120.4491Taiwan: 00.801.137.737Thailand: 001.800.120.665853Other countries: +65.6220.4666Lutron Electronics Co., Inc.Made and printed in U.S.A. PN 032-218 Rev. C 05.01.09

Navigation menu