Lutron Electronics 0070 Electronic control with RF communication User Manual
Lutron Electronics Company Inc Electronic control with RF communication
User Manual
R
Installation Instructions
Occupant Copy Please Read
SZ-CI-USB-CPN5138
USB Interface
PELV (Class 2: USA) Device
5 V 60 mA
StanzaTM
Features
• Integrates a Stanza guest room lighting control system
with a PC or other digital equipment that supports USB
devices.
• Provides a basic serial string command set that allows a
PC to monitor and control lighting.
• Programmed and commissioned by a SZ-CI-PRG
Programming Control Interface.
• Should not be used in “Advanced” systems with a
permanently installed SZ-CI-PRG.
• Wireless connection allows easy mounting near
integration device.
Mounting
1. Secure the provided mounting clip to a flat, clean
surface with the double-sided tape on the clip.
Then secure the USB interface in the mounting
clip.
2. Connect the provided USB cable from the device
to the 3rd party equipment.
3. Use provided antenna clip and double-sided tape
to securely mount the antenna.
4. Mount in an accessible location for convenient
access to the programming button, LED, and USB
cable.
5. The unit cannot be mounted in a full metal
enclosure or between two metal surfaces.
6. When mounting, provide sufficient space for the
antenna and USB cable.
FCC Information
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this
equipment. Operation is subject to the following: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Dimensions
Dimensions are in inches.
0.89 0.843
0.44 0.255
4.0 0.5
1.691 0.78
Antenna Clip
Mounting Clip
USB Mini-B Female Connector
31.5
FCC Information
Changes or modications not expressly approved by Lutron
Electronics Co. could void the user’s authority to operate this
equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. Operation is subject to the following: (1) This device may
not cause harmul interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
R
Lutron Electronics Co., Inc.
Made and printed in U.S.A.
P/N 040-361 Rev. A 04.21.10
Internet: www.lutron.com/stanza e-mail: product@lutron.com
Technical support: USA, Canada, Caribbean: 1.800.523.9466
Mexico: +1.888.235.2910
Central/South America: +1.610.282.6701
Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with 8-year pro-rated parts
replacement on systems that include factory startup.
For complete warranty details, see the Start-Up/Warranty document provided with your Stanza system
specification submittal information.
Lutron and the sunburst logo are registered trademarks and Stanza is a trademark of Lutron Electronics
Co., Inc. © 2010 Lutron Electronics Co., Inc.
Mounting Clip
Device Operation
USB Mini-B Female Connector
LED
Off during normal operation
(unless TX / RX monitoring
is enabled).
Flashes Orange during
programming mode.
Button
Used during device programming
for association to Stanza system.
Troubleshooting
Symptom Cause and Action
Device does not address to system. Device not powered
• Connecting equipment is not powered
• USB port on connecting equipment not powered
Device out of RF range
• Ensure device is within 30 ft (9 m) of StanzaTM device congured as a repeater
Device is programmed to another system
• Contact Lutron Technical Support for details on how to factory default the device
COM port cannot be established with
device
Device not powered
• Connecting equipment is not powered
• USB port on connecting equipment not powered
Virtual COM port is set up incorrectly
• See the Lutron Integration Protocol guide for proper COM port settings
Device does not respond to integration
commands
Virtual COM port is set up incorrectly
• See the Lutron Integration Protocol guide for proper COM port settings
Device is not programmed to system
• Ensure device was addressed to an existing Stanza system
Incorrect integration commands
• Ensure that the proper commands and integration IDs are being used
StanzaTM system devices do not respond
to issued integration commands
Device out of RF range
• Ensure device is within 30 ft (9 m) of Stanza device congured as a repeater
Incorrect integration commands
• Ensure that the proper commands and integration IDs are being used
Device does not monitor system changes Virtual COM port is set up incorrectly
• See the Lutron Integration Protocol guide for proper COM port settings
Device is not programmed to system
• Ensure device was addressed to an existing Stanza system
Device out of RF range
• Ensure device is within 30 ft (9 m) of Stanza device congured as a repeater
Monitoring disabled
• See the Lutron Integration Protocol guide for disabling/enabling monitoring