Lutron Electronics 0114 Wireless Dimmer Switch User Manual 0301815a
Lutron Electronics Company Inc Wireless Dimmer Switch 0301815a
Contents
- 1. 0301815a Instruction sheet
- 2. Regulatory statements
0301815a Instruction sheet
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2923670 |
| Application ID | zzRNppU6YxsidLUlks+5Hg== |
| Document Description | 0301815a Instruction sheet |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 25.94kB (324282 bits) |
| Date Submitted | 2016-03-09 00:00:00 |
| Date Available | 2016-03-09 00:00:00 |
| Creation Date | 2016-02-10 11:29:56 |
| Producing Software | Acrobat Distiller 10.1.16 (Windows) |
| Document Lastmod | 2016-02-11 09:26:55 |
| Document Title | 0301815a.pdf |
| Document Creator | Adobe InDesign CS6 (Windows) |
| Document Author: | ptielmann |
GRAFIK T TM Installation Instructions Please Read Before Installing Installation P/N 0301815 Rev A 1 Turn OFF power at circuit breaker. RRT-GH2B RRT-GH4B RRT-GH5B RRT-GH6B HQRT-GH2B HQRT-GH4B HQRT-GH5B HQRT-GH6B LED 6b Shock Hazard. May result in serious injury or death. Turn off power at ! WARNING! circuit breaker before installing the unit. 120 V~ 50 / 60 Hz Model Numbers Hybrid Keypad 1,2,3 Operation English 2 Remove wallplate and the switch mounting screws. Leaving all wires attached, carefully pull Incandescent / Halogen MLV 4,5,6,7 Halogen the switch out from the wall. Dimmable Electronic Ballast or Driver 8,9,10 250 W 400 VA (300 W) Multi-location – 3-way switches will have insulated wires connected to three screws plus a green ground screw. One of the wires is connected to a screw of a different color (not green) or labeled COMMON. Tag this wire. Companion devices RT-GRDW For use with RRT– hybrid keypads, dimmers and switches (0.1 A) HQT-GRDW For use with HQRT– hybrid keypads, dimmers and switches (0.1 A) Different-colored screw Ground Tag/Common 4 The switch may have two wires attached to the same screw. Tape these two wires together before disconnecting. Proceed to disconnect the wires from the switch. Hybrid Keypad 5 Remove wallplate from the GRAFIK TTM hybrid keypad and any companion device but leave Line / Hot wallplate adapter connected. 1. CAUTION: To avoid overheating and possible damage to other equipment, do not use hybrid keypads to control receptacles or motor-operated appliances. 2. Install in accordance with all national and local electrical codes. 3. When no “grounding means” exist in wallbox, the NEC® allows control without a grounding connection to be installed as a replacement if 1) a non-metallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). For this type of installation, cap or remove the green ground wire on the hybrid keypad, and only use a Lutron® GRAFIK TTM wallplate. 4. GRAFIK TTM controls are not compatible with standard 3-way switches. Use only with GRAFIK TTM companion devices. 5. GRAFIK TTM Companion devices cannot be used individually but must be used in conjunction with a GRAFIK TTM hybrid keypad in a multi-location application. 6. In any multi-location circuit, use only one GRAFIK TTM hybrid keypad with up to four GRAFIK TTM companion devices. 7. Neutral wire connection is optional for GRAFIK TTM hybrid keypad; however, the best dimming performance will be obtained when the neutral wire is connected. Always cap the white wire if a neutral wire is not present in wallbox. 8. Return to Factory Settings (Note: Returning a control to the factory settings will remove it from the system and erase all programming). Step 1: Triple tap any button on a control. DO NOT release after the third tap. Step 2: Keep the button pressed on the third tap (for approximately 3 seconds) until the LEDs on the control start to scroll up and down quickly. Step 3: Release the button and immediately triple tap the button again. The LEDs on the control will scroll up and down slowly. Factory settings have been restored. Blue Blue Tag/Common • Buttons provide scene / zone status • Buttons are fully programmable 6a Tag/Common Companion device(s) Red White 120 V~ 60 Hz Connect if using neutral wire Green Black White Green Ground Ground Tag/Common Blue Green Load Neutral Neutral wire connection is optional for GRAFIK TTM hybrid keypads; however, the best dimming performance will be obtained when neutral wire is connected. The companion device is wired differently than a standard 3-way switch. Both the Red wire and the tagged wire are connected to the same traveler wire. 7 Carefully push wires into the wallbox. Install controls and snap on wallplate. 9 If desired, consider adjusting low-end and high-end trim by using the RadioRA® 2 or HomeWorks® QS GUI software. Minimum Load: Load Ground Number of Companion Devices LED 1, 2 Single-pole 3 LED lamps 80 W 4 LED lamps 120 W 5 LED lamps 160 W 6 LED lamps 200 W 7 LED lamps 240 W Multi-location Cut the blue wire at the insulation and cap with the yellow connector. Load Type Incandescent / Halogen 3 Application Neutral IMPORTANT Red 8 Turn ON power at circuit breaker. Blue DBM: Dynamic Backlight Management Sensor Note: DBM should be mounted with an unobstructed, clear view of the floor. DO NOT paint or plaster over sensor. Hybrid Keypad Blue Connect the Red wire on the hybrid keypad to the other wire removed from the switch. Black Ground Live Connect the Black wire on the hybrid keypad to one of the wires removed from the switch. If you had taped together two wires (see step 4), connect both wires to the Black wire on the hybrid keypad and remove the tape. Line / Hot Green Ground Connect the Green ground wire on the hybrid keypad to the Green or bare ground wire in the wallbox (See Important Notes, number 3). Red IMPORTANT NOTICE: FASSTM – Front Accessible Service Switch To replace lamp(s), power may be conveniently removed by pulling the FASSTM down on the hybrid keypad. After replacing lamp(s), push the FASSTM back up fully to restore power to the hybrid keypad. For any procedure, other than routine lamp replacement, power must be turned OFF at the main electrical panel. Hybrid Keypad Load-Side (without neutral wire only) 1 Single-pole – Switch will be replaced by a GRAFIK TTM hybrid keypad. Connect the White wire on the hybrid keypad to the neutral wire in the wallbox (See Important Notes, number 7). FASSTM : Front Accessible Service Switch Note: FASSTM is not available on companion devices. Neutral Green Neutral 1 (Connect if using neutral wire) 6 Install GRAFIK TTM control. Flexible Control Load White Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USA Black Red Companion device(s) Red • Top button toggles local load On/ Off • All other buttons flutter to indicate uncommissioned status • Press to activate a scene or zone Tag/Common Recommended LEDs Important Notes Off Hybrid Keypad Line-Side (with or without neutral wire) 1 connectors provided are for copper wires only. For aluminum IMPORTANT Wire wires, consult an electrician. If dimming LED bulbs, they must be Lutron® compatible! For current compatibility and performance information visit www.lutron.com/LED. Nightlight Companion Device Connect the Green wire on the companion device to the Green or bare ground wire in the wallbox (See Important Notes, number 3). Connect the Red wire on the companion device to the tagged wire and to the same color wire connected to the Red wire on the hybrid keypad . Connect the Blue wire on the companion device to the remaining wire. Ground GRAFIK TTM -GH2B, -GH4B, -GH5B, and -GH6B models can control power boosters / load interfaces if neutral is used. See Lutron® P / N 369971 and 369985, Compatible Power Boosters and Load Interfaces. RRT- models are RadioRA® 2 compatible and HQRT- models are HomeWorks® QS compatible. Not for use with receptacles or appliances (e.g., garbage disposals). See Lutron® Application Note #109 for compatibility with dimmed receptacles. Magnetic Low-Voltage Applications: Use with halogen-based lamps only. UL® listed for use with dimmable ELV transformers, but not recommended because Lutron does not do system performance testing. Operation of a low-voltage circuit with lamps inoperative or removed may result in transformer overheating and premature failure. Lutron strongly recommends the following: • Do not operate low-voltage circuits without operative lamps in place. • Replace burned-out lamps as soon as possible. • Use transformers that incorporate thermal protection or fused transformer primary windings to prevent transformer failure due to overcurrent. When using the hybrid keypad to control MLV halogen-based fixtures, the maximum lamp wattage is determined by the efficiency of the transformer, with 70%–85% as typical. For actual transformer efficiency, contact either the fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the hybrid keypad. Ten (10) driver maximum. Includes Lutron® Hi-lume® 1% 2-wire LED drivers, Mark XTM, Tu-Wire®, and POWERSENSE®. 10 Neutral is required for Mark XTM, Tu-Wire®, and POWERSENSE®. Day Evening Single-pole – The switch will have insulated wires connected to two screws of the same color plus a green ground screw. 3.3 A (400 VA) Uncommissioned Behavior Hybrid Keypad Connect the Green ground wire on the hybrid keypad to the Green or bare ground wire in the wallbox (See Important Notes, number 3). Connect the Black wire on the hybrid keypad to the tagged wire removed from the switch. Connect the Red wire on the hybrid keypad to one of the remaining wires. Connect the Blue wire on the hybrid keypad to the remaining wire. Connect the White wire on the hybrid keypad to the neutral wire in the wallbox (See Important Notes, number 7). 3 Identify switch type. 600 W (Not ganged) 500 W (End of gang) 400 W (Middle of gang) Multi-location – Lamps can be controlled from multiple locations. One location will be replaced by a GRAFIK TTM hybrid keypad and the other location(s) by a GRAFIK TTM companion device. If the neutral wire is not being used, the hybrid keypad can be wired on the line-side or the load-side. If using the neutral wire, the hybrid keypad must be wired on the line-side. See Recommended LEDs. If using neutral wire, the minimum load required is one LED lamp or Lutron® Hi-lume® 1% 2-wire LED driver. If using neutral wire, the minimum incandescent/halogen load required is 5 W. Troubleshooting Symptom Possible Solutions • Push FASSTM up to restore power. • Turn ON breaker. 1. Lamp and light bar • Replace burned out lamp(s). LEDs do not turn on. • Check hybrid keypad wiring (See Installation). • Cycle power to unit by pulling the FASSTM down and back up to fully restore power. If unit beeps see Symptom 2. • Check wiring. If neutral wire is connected, ensure that the Black wire is connected to Live and the Red wire is connected to Load. 2. Unit beeps after power cycle. • Check wiring. Ensure that the Blue and Red wires are connected as specified in Installation. 3. Lamps turn On and • Ensure that the wire connected to the Blue (or Red) wire on the hybrid hybrid keypad works keypad is the same as that connected to the Blue (or Red) wire on the but companion device companion device (See Installation Step 6b). does not work. 4. Lamps repeatedly • See Minimum Load and ensure the acceptable minimum load is met. turn On and Off. 5. Lamps flicker or exhibit • Set low-end trim. See Installation Step 9 for details. poor dimming range. • See Recommended LEDs. • Solid-state hybrid keypads internally dissipate about 1% of the total connected load. It is normal for hybrid keypads to feel warm to the touch 6. Wallplate is warm. during operation. • Improper programming. Programming must be done through the system software. 8. Lamps don’t turn • Out of RF range. Reposition to be within 30 ft (9 m) of an RF signal repeater. On / Off from a • Wires shorted. Make sure the blue terminal is not grounded or shorted to keypad. any other wires. • Wiring error. Ensure wiring matches installation instructions and appropriate wiring diagram. 9. All LEDs on the hybrid • The hybrid keypad is in factory settings mode and has not been keypad flash when configured to work in a system. Follow the steps in the System Setup any button is pressed. Guide to program. Customer Assistance: www.lutron.com U.S.A. | Canada | Caribbean: 1.844.LUTRON1 | Mexico: +1.888.235.2910 | Others: +1.610.282.3800 • For warranty details, please visit: www.lutron.com/TechnicalDocumentLibrary/warranty.pdf | For FCC/IC information, please visit: www.lutron.com/fcc-ic Lutron, C•L, Hi-lume, and Tu-Wire are registered trademarks and FASS, and GRAFIK T are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. POWERSENSE is a registered trademark of Osram Sylvania, Inc. Mark X is a registered trademark of Philips Lighting Electronics N.A., Inc. © 2014-2015 Lutron Electronics Co., Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : ptielmann Create Date : 2016:02:10 11:29:56-05:00 Modify Date : 2016:02:11 09:26:55-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:02:11 09:26:55-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:52a0fc6a-91d2-4641-a3b1-c347add8e475 Original Document ID : xmp.did:F9DAAD7F536BE411BED4A40E3062C96F Document ID : xmp.id:0D91DE5713D0E511A3E8FE9C0949FAAD Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0C91DE5713D0E511A3E8FE9C0949FAAD Derived From Document ID : xmp.did:0C91DE5713D0E511A3E8FE9C0949FAAD Derived From Original Document ID: xmp.did:F9DAAD7F536BE411BED4A40E3062C96F Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:02:10 11:29:24-05:00 Format : application/pdf Creator : ptielmann Title : 0301815a.pdf Producer : Acrobat Distiller 10.1.16 (Windows) Trapped : False Page Count : 1EXIF Metadata provided by EXIF.tools