Luxul Wireless XAP1440 AC1200 Dual-Band Outdoor Wireless Access Point User Manual Revised
Luxul Wireless AC1200 Dual-Band Outdoor Wireless Access Point Revised
Contents
- 1. User Manual
- 2. User Manual Revised
User Manual Revised
Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
AC1200 Dual-Band Outdoor
Wireless Access Point
XAP-1440
Includes:
XAP-1440 Wireless Access Point
PoE Injector and Power Cord
Mounting Bracket and Hardware
Ethernet Cable
READ ME FIRST - CONTROLLER COMPATIBILITY
This XAP-1440 is compatible with the Luxul Wireless Controller for fast, easy
configuration and deployment of wireless networks with multiple APs.
nNote: If you’ll be using this AP with a Wireless Controller, refer to
the Quick Install Guide included with the Wireless Controller for
setup instructions.
AP SETUP AND CONFIGURATION
1 Physical Installation
The XAP-1440 access point is designed for simple and ecient installation.
However, due to the inherent complexity of outdoor installation,
installation shall be performed only by experienced professionals.
Because the signal generated by the XAP-1440 is directional, the unit should
be located at the perimeter of the desired coverage area, with the large flat
surface aimed toward the center.
Mounting the Access Point
Mounting the access point is a simple process outlined in the following steps.
1. Refer to the included Mounting Guide leaflet to assemble the mount and
secure the AP to a pole or wall mount.
2. Thread the Ethernet cable through the cable gland assembly as shown,
connect it to the Ethernet connector, secure the cable gland to the
threaded recess on the access point, then tighten the cable gland nut to
secure and seal the cable gland.
Cable gland exploded view
3. Adjust the access point for best performance. The vertical elevation
angle can be adjusted with the four hex screws on the mount, while the
horizontal angle can be adjusted by loosening the clamp and rotating the
assembly on the pipe.
cCAUTION: To comply with RF regulations, the AP should be adjusted
from 0 to -20 degrees (horizontal to downward-facing).
wWarning: Do not locate the access point where it can come into
contact with overhead power lines or other electric circuits. When
installing the antenna, take extreme care not to come into contact
with such circuits, as they may cause serious injury or death.
nNote: For proper installation and grounding of the antenna, please
refer to national and local codes (e.g. U.S.: NFPA 70, National
Electrical Code, Article 810, Canada: Canadian Electrical Code,
Section 54). Statement 280.
Sales
801-822-5450
sales@luxul.com
Technical Support
801-822-5450
support@luxul.com
LUX-QIG-XAP-1440-v1 05121709
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission in
writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license
only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
Fold Fold Fold
AP SETUP AND CONFIGURATION CONT.
2 Connecting Ethernet and Power
Ethernet and Power
The XAP-1440 is PoE ready and supports 802.3at PoE. A PoE injector is
included with the device. To apply power, simply connect the end of the
Ethernet cable to which the access point is connected to the provided PoE
injector or other PoE switch. An Ethernet cable length of up to 300 feet can
be used.
nNote: Luxul recommends at least Cat-5e unshielded twisted pair
(CAT5e UTP) cabling. To ensure best performance and stable data
transmission at 1000 Mbps, use Category-6 unshielded twisted pair
(CAT6 UTP).
PoE Injector Setup
XData In: Connect an Ethernet cable from your router or switch to the
Data In port of the included PoE Injector
XData & PWR Out: Connect an Ethernet cable from the Data & PWR Out
port of the included PoE Injector to the PoE Port of the XAP-1440
XAC Power: Connect the included AC Cord to the Power Input of the
Included Injector first and then to the AC outlet.
Power
Source
From your
Router or Switch
Luxul AP
IN
OUT POE
Injector
PoE injector
3 Preparing for Access
IP Addressing
If the XAP-1440 is connected to a network with a 192.168.0.X address scheme,
and your computer shares a similar address on the same network, you can skip
to the next step, Access and Setup.
nNote: If another device on your network shares the 192.168.0.10 address,
you’ll need to temporarily reassign or remove that device while
you configure the XAP-1440.
If your network uses an address scheme other than 192.168.0.X, you’ll need
to set a temporary static IP address on the computer you’re using for config-
uration. To do so, set the IP address of your computer to an address in the
192.168.0.X range.
Once you’re finished configuring the AP, you can return your computer’s IP
configuration to normal, typically “Obtain Automatically/DHCP.”
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
nNote: The XAP-1440 is not a router and will need to be connected to
a network with a router in order to deliver Internet access.
4 Access and Setup
Getting Connected
XConnecting Via an Ethernet Device: Use Ethernet cable to connect your
computer to the PoE switch or PoE injector to which the XAP-1440 is
connected. Ethernet is the preferred method of connection.
XConnecting Via a Wireless Device: Connect your client device to the
XAP-1440 default wireless network named Luxul_XAP-1440. The wireless
network will run in Open Security mode, so no passphrase is required until
Wireless Security is configured.
Logging In
To access the AP’s web configuration, open your web browser and enter the
AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using the
default user name and password:
Default IP: 192.168.0.10
Username: admin
Password: admin
Once logged in, use Quick Setup and follow the online help to configure
the access point as desired.
5 Hardware Operation
LED Indicators
The LED indicators are located on the bottom portion of the enclosure,
near the cable gland.
PWR: If the green Power LED is On, the XAP-1440
is powered. If the Power LED is O, the XAP-1440 is
not receiving power. The Power LED blinks when
the XAP-1440 is booting.
WLAN: If the blue LED is On, the wireless radio is
active and wireless access is enabled. O indicates the wireless radio is not
active and wireless access is disabled.
PoE Injector: If the Green ON LED is illuminated, power is connected to the
injector. If the ON LED is not lit, the injector is not receiving power.
Reset Button: The Reset button is located inside the cable
gland opening of the XAP-1440 and is used to restore factory
default settings. To Restore Default Settings, with the
XAP-1440 powered on, press and hold the Reset button for
approximately 10 seconds, then release.
cCAUTION: Holding the Reset button for more than a few seconds
will restore the AP to factory default and remove any
custom configuration.
Fold Fold Fold
FCC STATEMENT—WIRELESS FCC
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
FCC ID:
IC:
FCC Statement
This equipment has been tested and found to comply with the limits for a Class digital
device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one of the following measures:
X Reorient or relocate the receiving antenna.
X Increase the separation between the equipment and receiver.
X Connect the equipment to an outlet on a circuit dierent from that to which the
receiver is connected.
X Consult the dealer or an experienced radio/TV technician for help.
Refer to included Quick Installation Guide for device-specific FCC Class information.
FCC Caution: Any changes or modifications not expressly approved by the party responsi-
ble for compliance could void the user’s authority to operate this equipment.
XThis device complies with part 15 of the FCC Rules.
XThis transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
Maximum Output Power:
2.4GHz: 24.57dBm
5GHz Band 1: 21.38 dBm
5GHz Band 4: 26.25 dBm
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncon-
trolled environment. This equipment should be installed and operated with a minimum
distance of 40cm between the radiator & your body.
REGULATORY COMPLIANCE
The device complies with internationally-recognized standards covering human expo-
sure to electromagnetic fields from radio devices. This equipment also complies with
FCC radiation exposure set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 40cm (15.7 in) during normal operation.
Unauthorized antennas, modifications, or attachments could cause damage and
may violate regulatory approvals. Any changes or modifications not expressly
approved by the party responsible for compliance could void the authority to
operate the equipment.
Luxul equipment marketed in the U.S. is restricted to usage of channels 1-11 only for
2.4GHz and channels 36-48/149-165 for 5GHz.
Warnings and Safety Information
XEnsure that the electrical circuits have appropriate grounding,
overload and surge protection.
XAttach only approved power cords to the device.
XVerify there is adequate ventilation around the device, and that ambient
temperatures meet equipment operation specifications.
XDO NOT install in or near hot or humid places, such as a kitchen or bathroom.
Take care to minimize exposure to excessive heat or moisture.
XSmall parts and plastic bags used for packaging may be harmful to small children.
KEEP ALL ACCESSORIES OUT OF THE REACH OF CHILDREN!
Frequency/Band Information
Channel Frequency (MHz) US (FCC) Europe (ETSI)*
2.4GHz Band
12412
22417
32422
42427
52432
62437
72442
82447
92452
10 2457
11 2462
12 2467
13 2472
5GHz Band
36 5180
40 5200
44 5220
48 5240
149 5745
153 5765
157 5785
161 5805
165 5825
* On the European version of this product the maximum output power is
19.97dBm on frequencies 2412-2472MHz and 22.98dBm on frequencies 5180-5240MHz.
©2018 Luxul. All Rights Reserved.
The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and/or registered
trademarks of Luxul Wireless, Inc. All other trademarks and registered trademarks are property of their respective holders.
LUX-REG-COM-
This documentation contains regulatory compliance and safety information. No part of this publication, or any other
publication may be modified or adapted in any way, for any purposes without written permission from Luxul.
REGULATORY,
COMPLIANCE AND
SAFETY DOCUMENT
12884 S. Frontrunner Blvd, Suite 201
Draper, UT 84020-5490
1-801-822-5450
Last Update:
XAP-1440
AC1200 Dual-Band Outdoor Wireless Access Point
XAP1440-21218
02/12/18
W59XAP1440
8584A-XAP1440
2.4GHZ 802.11B/G/N
B
Fold Fold Fold
XThis product may become hot when in use for extended time periods. This is
normal and is not a malfunction. DO NOT install where it will be exposed to
paper, cloth or other flammable materials.
XOperation within the 5.15-5.25GHz frequency range is restricted to indoor use.
Health and Safety Recommendations
Warnings for the use of Wireless Devices: Please observe all warning notices with
regard to the use of wireless devices
Potentially Hazardous Atmospheres: You are reminded of the need to observe
restrictions on the use of radio devices in fuel depots, chemical plants, and other
similar areas where the air contains chemicals or particles (such as grain, dust, or
metal powders).
Safety in Hospitals: Wireless devices transmit radio frequency energy and may
aect medical electrical equipment. When installed adjacent to other equipment, it
is advised to verify that the adjacent equipment is not adversely aected.
RF Exposure Guidelines
Safety Information: The device complies with internationally-recognized standards
covering human exposure to electromagnetic fields from radio devices.
Warning: Exposure to Radio Frequency (RF) Radiation:
The radiated output of this device is below FCC radio frequency exposure limits.
Nevertheless, the device should be used in such a manner that the potential for
human contact during normal operation is minimized.
XThe end user must avoid any extended human RF exposure directly in front of the
device, up to a distance of 40cm, when the unit is on.
XWhen servicing the equipment and selecting a location for the antennas, it
is important to note that a minimum distance of 40cm is required between
personnel and the device or antenna, to comply with radio frequency
exposure limits.
XThe antenna used for this transmitter must be installed to provide a separation
distance of at least 40cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
The following safety precautions should be observed:
XDo not touch or move the antenna while the unit is transmitting or receiving.
XDo not hold any component containing the radio such that the antenna is very
close or touching any exposed parts of the body, especially the face or eyes,
while transmitting.
XDo not operate the radio or attempt to transmit data unless the antenna is connected;
this behavior may cause damage to the radio.
ErP Statement
The purpose of this product is to create a constant network connection for your devices.
It does not have a standby mode or use a power management mode. If you wish to power
down this product, please unplug it from the power socket.
Industry Canada
This device complies with Industry Canada licence-exempt RSS-247 standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR-247 d’Industrie Canada applicables aux appa-
reilsradio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en comprom-
ettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of
RSS-102 and compliance with RSS-102 RF exposure; users can obtain Canadian information
on RF exposure and compliance.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de
RSS-102 et la conformité à l’exposition de RSS-102 rf, utilisateurs peut obtenir l’information
canadienne sur l’exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with a minimum
distance of 40 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune
autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une
distance minimum de 40 centimètres entre le radiateur et votre corps.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be
such that the equipment still complies with the e.i.r.p. limits specified for point-to-point
and non-point-to-point operation as appropriate.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande de 5725 à 5850
MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l’exploitation point à point
et l’exploitation non point à point, selon le cas;
CAN ICES-3( )/NMB-3( )
Simplified EU declaration of conformity
Hereby, Luxul declares that the radio equipment type is in compliance
with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: http://luxul.com/regulatory-compliance
Le soussigné, Luxul, déclare que l’équipement radioélectrique du type est
conforme à la directive 2014/53/UE.
Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet
suivante: http://luxul.com/regulatory-compliance
Hiermit erklärt Luxul, dass der Funkanlagentyp der Richtlinie 2014/53/EU
entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden
Internetadresse verfügbar: http://luxul.com/regulatory-compliance
Hierbij verklaar ik, Luxul, dat het type radioapparatuur conform is met
Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het
volgende internetadres: http://luxul.com/regulatory-compliance
XAP-1440
XAP-1440
XAP-1440
XAP-1440
B B