Luxul Wireless XAP810 AC1200 Dual-Band Wireless Access Point User Manual

Luxul Wireless AC1200 Dual-Band Wireless Access Point

User manual

Fold Fold FoldREAD ME FIRSTQUICK INSTALL GUIDEAC1200 Dual-Band Wireless Access PointXAP-810Includes: AC1200 Dual-Band Wireless AP Mounting Brackets  and Hardware PoE Injector and  Power Cable Ethernet CableREAD ME FIRST - CONTROLLER COMPATIBILITYThis XAP-810 is compatible with the Luxul Wireless Controller for fast, easy configuration and deployment of wireless networks with multiple APs. nNote: If you’ll be using this AP with a Wireless Controller, refer to  the Quick Install Guide included with the Wireless Controller for  setup instructions.AP SETUP AND CONFIGURATION1 Physical InstallationThe XAP-810 access point is designed for simple and ecient installation and can be located one of three ways. First, the included mount is designed to attach directly to several dierent regions’ standard electrical boxes. Second, the XAP-810 may be mounted on a ceiling or wall without a box by using the included mount as a guide to mark attachment locations. Finally, the XAP-810 can be placed on a flat surface by attaching the included rubber feet to the mount. cCaution: Attach the rubber feet to the mount and attach the mount to the AP for flat surface placement to avoid overheating and failure. XSingle Access Point Placement: Because the signal generated by the XAP-810 is omnidirectional, the unit should be located as near as possible to the center of the desired coverage area.XAP-810 Single AP Coverage Pattern XMultiple Access Point Placement: You may need to experiment with AP placement to optimize the roaming experience. Place APs to ensure adequate coverage, but not so far apart that there is no signal overlap. Adjacent APs should overlap enough that the client device has a good connection to the AP to which it is currently attached, but also sees the next-nearest AP. Ideally, roaming clients should see signal strength of  two overlapping APs in the range of -60 to -70 dBm at the midway  point between two APs. To learn more about AP placement, visit  luxul.com/ap-placement.Ideally, roaming clients should see signal strength of two overlapping APs in the range of -60 to -70 dBm at the midway point between two APsXAP-810 Multiple AP Coverage and Overlap nNote: Consider using Ekahau HeatMapper to assist with this process, available from www.ekahau.com. Luxul also oers an informative “How-To” video on HeatMapper at luxul.com/how-to-videos.AP SETUP AND CONFIGURATION CONT.2 Connecting Ethernet and PowerEthernet and PowerTo apply power and network simultaneously, simply connect one end of an Ethernet cable to a PoE switch, and the other end to the XAP-810 PoE port. To connect power and Ethernet separately, first connect an Ethernet cable from the supplied PoE Injector Data & PWR Out port to the PoE port on the XAP-810. An Ethernet cable length of up to 300 feet can be used.Sales801-822-5450 sales@luxul.comTechnical Support801-822-5450 support@luxul.comLUX-QIG-XAP-810-v3 07171703                             Copyright and Trademark NoticesNo part of this document may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and registered trademarks are property of their respective holders.
Fold Fold FoldNext, connect an Ethernet cable from your Router or Switch to the Data IN port on the PoE Injector. Finally, connect the AC cord to the included PoE Injector, then to the AC outlet. nNote: Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP) cabling. To ensure best performance at 1000 Mbps, use CAT6 UTP.PoE Injector Setup XData In: Connect an Ethernet cable from your router or switch to the Data In port of the included PoE Injector. XData & PWR Out: Connect an Ethernet cable from the Data & PWR Out port of the included PoE Injector to the PoE Port of the XAP-810. XAC Power: Connect the included AC Cord to the Power Input of the Included Injector first and then to the AC outlet.PowerSourceFrom yourRouter or SwitchLuxul APDATA  I NDATA  &  PWR OUT POEInjectorPoE injector3 Preparing for AccessIP AddressingIf the XAP-810 is connected to a network with a 192.168.0.X address scheme, and your computer shares a similar address on the same network, you can skip to the next step, Access and Setup.If your network uses an address scheme other than 192.168.0.X, you’ll need to set a temporary static IP address on the computer you’re using for config-uration. To do so, set the IP address of your computer to any address in the 192.168.0.X range other than 192.168.0.10.Once you’re finished configuring the AP, you can return your computer’s IP configuration to normal, typically “Obtain Automatically/DHCP.” nNote:    Visit  http://luxul.com/ip-addressing to learn more about changing your computer’s IP address and getting connected.4 Access and SetupGetting Connected XConnecting Via an Ethernet Device: Use Ethernet cable to connect your computer to the PoE switch or PoE injector to which the XAP-810 is connected. Ethernet is the preferred method of connection. XConnecting Via a Wireless Device: Connect your client device to the XAP-810 default wireless network named Luxul_XAP810 or Luxul_XAP810_5G. The wireless network will run in Open Security mode, so no passphrase is required until Wireless Security is configured. Logging InTo access the AP’s web configuration, open your web browser and enter the AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using the default user name and password: Default IP:  192.168.0.10  Username: admin  Password: admin  nNote:   If another device on your network shares the 192.168.0.10 address, you’ll need to temporarily reassign or remove that device while you configure the XAP-810. nNote:  The XAP-810 is not a router and will need to be connected to a network with a router in order to deliver Internet access.5 Hardware OperationLED IndicatorsEnclosure: If the green Power LED is on, the XAP-810 is powered and working. If the Power LED is OFF, the AP is not receiving power or the LED has been turned o in the AP’s web interface. If the green Power LED is blinking, the XAP-810 is booting. The two blue LEDs indicate indicate each of the 2.4GHz and 5GHz networks are configured and broadcasting.XAP-810 LED’sPoE Injector: If the PWR LED is On, Power is Connected to the injector. If the PWR LED is O, the injector is not receiving power.  Reset ButtonThe Reset button is located underneath the mount and marked RESET. It may be used to reboot the AP or to restore factory default settings.Reboot the AP: With the XAP-810 powered on, simply press and release the Reset button.Restore Factory Defaults: With the XAP-810 powered on, press and hold the Reset button for 10 seconds, then release the button and the XAP-810 will restore factory defaults and reboot. cCAUTION:  Holding the Reset button for more than a few seconds will restore the AP to factory default and remove any custom configuration.

Navigation menu