Lyngsoe Systems PR34X-V Radio Module User Manual PR34X User Guidex
Lyngsoe Systems Ltd. Radio Module PR34X User Guidex
User Manual
Lyngsoe Systems PR34X- RFID Reader
950XXX_.pdf Rev: 1.0 Page 1 of 4
PR34X – Belt Loader
RFID Reader
User Guide
Doc.# 950XXX Rev. A Date: April 16, 2016
Lyngsoe Systems PR34X- RFID Reader
950XXX_.pdf Rev: 1.0 Page 2 of 4
1. General
The PR34X-V and PR34X-A Belt Loader RFID (RAIN) Reader are exclusively designed
for application in the United States. Application is specific for:
placement on belt loaders used for loading baggage on aircraft
use on Verizon Wireless Network (PR34X-V)
use on AT&T Wireless Network (PR34X-A)
2. PR34X Block Diagram
SingleBoard
Computer
RFIDModule
GPSReceiver
Module
LTE4G
Module
WiFiModule
Internal
Antenna
IntegratedAntennaorExternal
I/O
Module
ExternalGPS
Antenna
ExternalCellular
Antenna
Powerand
RS485Bus
12.0V
DCPower
PhotoSensor
PhotoDiode
LEDStack
BeltMotionSensor
andBypassstop
Power
Management
Module
HostPCBAssembly
PR34XEnclosure
Optional
PR34X‐V,PR34X‐ABlockDiagram
ExternalAntenna
Lyngsoe Systems PR34X- RFID Reader
950XXX_.pdf Rev: 1.0 Page 3 of 4
3. Installation:
Installation and maintenance of the product is the sole responsibility of the Airline.
(Installation procedures to be provided by Airline). Equipment is to be mounted in a
secure way to ensure equipment cannot fall off or be easily knocked off. Mounting
brackets and mounting bracket designs are the responsibility of the airline and or Belt
Loader Manufacturer. It is recommended that the Airline and or Belt Loader Manufacturer
consult with Lyngsoe Systems regarding mounting bracket design, placement and best
practices to ensure optimum performance and compliance to FCC rules.
The unit comes with a standard wire harness.
Custom wire harnesses can be provided on request. A fee will be charged for this service.
Mounting instructions are to be provided by the airline, airline systems integrator or belt
loader manufacturer and approved by Lyngsoe Systems Ltd.
Regarding Antenna installation: The antenna must be installed at a separation
distance of at least 32 cm from all persons, and must not be co-located or operation
in conjunction with any other antennas or transmitters.
4. Operation
Operation and function is specific for each application. Lyngsoe Systems and or its partner
will provide approved middleware for relaying capture data to user application. Details and
middleware performance are out of scope of this manual.
Radio module performance is limited to meet FCC and network provider requirements.
They are not accessible or controllable by the end user.
Lyngsoe Systems PR34X- RFID Reader
950XXX_.pdf Rev: 1.0 Page 4 of 4
FCC compliance
Caution:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
(2) FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
To comply with FCC’s RF radiation exposure requirements, all the antennas used with the
Transmitters of this device must be installed such that a minimum separation distance of
32 cm is always maintained between the closest point of any radiator (antenna) & its
user’s or any nearby person’s body at all times. This device must not be co-located or
operating in conjunction with any other antenna or transmitters.