MARKTRACE MR6211 UHF RFID Reader User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3618102
Application ID	tGgmoHgfEiESuHGWXLM9dw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.47kB (830889 bits)
Date Submitted	2017-10-26 00:00:00
Date Available	2017-10-31 00:00:00
Creation Date	2017-10-26 17:37:02
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2017-10-26 17:37:16
Document Title	MSR-A2移动智能识读器用户手册
Document Creator	Acrobat PDFMaker 9.1 Word 版
Document Author:	GHOST

◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
MR6211 Serial
UHF Reader User Manual
Shenzhen Marktrace Co., Ltd
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
FCC caution
Federal Communication Commission (FCC) Radiation Exposure Statement
When using the product, maintain a distance of 20cm from the body to ensure compliance
with RF exposure requirements.
FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications or changes to this equipment. Such
modifications or changes could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
Dear Customer：
Many thanks for purchasing Marktrace device.
Go through the user manual carefully before you operate.
To make sure Marktrace device work correct. Any questions,
please contact us. We welcome your feedback and comments.
Shenzhen Marktrace Co.,Ltd
MR6211 Serial UHF reader User
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
Manual
(Ver1.0)
Disclaimer
Martkrace reserve the right to update and modify this user manual. For the
new documents may has no further notice.
Don’t tear up the warranty label or take reader apart to repair by yourself, we
reject perform warranty duties if this happened.
Shenzhen Marktrace Co.,Ltd have trademark right on the trademark which in
this user manual and receive legal protection. DO NOT make free with theses
trademarks.
®
Customer Service Center
Phone：400-022-3382
0755-2654 6392/2654 4205
Fax：0755-2655 3743
E-mail：technical@ marktrace.com
Website：http://www.marktrace.com
Address:Floor 3/5, Block D,Changyuan New Material Port, No
2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.R.C.
Post：518057
Contents
1 MATTERS NEED ATTENTION .............................................. 7
2 READER INSTRUCTION ................................................... 8
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
2.1 MR62XX SERIAL UHF READER INTRODUCTION................................. 8
2.2 READER INSTRUCTION ..................................................... 8
2.3 READER APPLICATIONS .................................................... 9
2.4 READER MAIN FUNCTIONS ................................................. 10
2.5 READER TECHNICAL PARAMETER ........................................... 10
3 READER STRUCTURE AND INTERFACE EXPLANATION ..................... 12
3.1 READER STRUCTURE EXPLANATION ......................................... 12
3.2 EXPLANATION ON THE READER COMMUNICATION INTERFACE ..................... 13
4 QUICK START GUIDE .................................................... 15
5 READER PARAMETER CONFIGURATION .................................. 17
5.1 W EBPAGE CONFIGURATION ................................................ 17
5.2 DEMO SOFTWARE CONFIGURATION ......................................... 20
5.2.1 Reader connection .................................................. 20
5.2.2 Antenna & RF Power setting.......................................... 20
5.2.3 Frequency Setting................................................... 21
5.2.4 Working Mode Setting................................................ 22
5.2.5 Buzzer & LED Setting ............................................... 22
5.2.6 IP Address Setting .................................................. 23
5.2.7 GPIO Setting ....................................................... 23
6 DEMO SOFTWARE DEMONSTRATION ..................................... 24
6.1 EPC GEN2 TAG DEMONSTRATION .......................................... 24
6.1.1 Multi tag Identify .................................................... 24
6.1.2 Multi Tag Read & Write .............................................. 25
6.1.3 Tag Filter .......................................................... 26
6.1.4 EPC Gen2 Tag Lock ................................................ 27
6.1.5 EPC Gen2 Tag Read and write with Access Password ................... 28
6.1.6 EPC Gen2 Tag Kill. ................................................. 29
6.2 ISO18000-6B PROTOCOL TAG DEMONSTRATION .............................. 29
6.2.1 ISO18000-6B tag Identify ............................................ 29
6.2.2 Multi-tag user data reading ........................................... 30
6.2.3 Single tag data reading and read with UID .............................. 31
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
6.2.4 Single tag writing and write with UID ................................... 32
6.2.5 Single tag data lock ................................................. 32
6.2.6 Single tag lock and query ............................................ 32
7 READER STRUCTION AND INSTALLATION SKETCH MAP ................... 34
8 SECONDARY DEVELOPMENT ............................................ 37
9 COMMON FAULTS AND EXCLUSION METHODS ............................ 38
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
1 Matters need attention
1、 Dismantle and parts replace：Marktrace has no warranty duties on those
faults which caused by dismantle and parts replace by customer .；
2、 Power supply：please use the power adaptor which alone with precuts to
get power. If not may harm the products.；
3、 Falling damage：Mind parts damage by device falling, if this happens, turn
off power immediately and connect the distributor or Marktrace customer
service center.；
4、 Unusual condition：Away from fire. If you find unusual odor when you use
this products, or reader on overheating or emitting smog, please power off
immediately and drop plug form the plug seat. You can connect the
distributor or Marktrace customer service center for helps. If you continue
to use this device, may cause the danger of fire or electronic shock.；
5、 Place：Don’t place device on the site which is not level, mind damage or
personal injury on falling.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
2 Reader instruction
2.1 MR62XX Serial UHF reader introduction
MR6211
MR6221
Product Model
MR6211E-A
MR6211E-E
MR6221E-A
MR6221E-E
MR6261E-A
MR6261E-E
MR6261
Product name
Parameter
Long range integrated
rfid reader
Long range integrated
rfid reader
Middle range integrated
rfid reader
Middle range integrated
rfid reader
Desktop integrated rfid
reader
Desktop integrated rfid
reader
12dBi Linear polarized
Frequency 902~928MHz，
12dBi Linear polarized
Frequency 865~868MHz
9dBi Circular polarized，
Frequency 902~928MHz
9dBi Circular polarized，
Frequency 865~868MHz
3dBi Circular polarized，
Frequency 902~928MHz
3dBi Circular polarized，
Frequency 865~868MHz
2.2 Reader instruction
This products has the features like multi protocol compatible, multi-tag identify,
multi-tag multi area read and write, fast reader speed, can connect to four
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
antennas etc.：
1、 Accord with ISO18000-6B and ISO18000-6C(EPC-GEN2) standard；
2、 Use unique anti-collision algorithm，has the super multi-tag identify ability；
3、 Have tag identify function and data area read, write, lock and kill these
functions. And supply the suit API to customer to do secondary
development.；
4、 Multi-tag identify ability：The MAX reader range can reach 8 meters.
（ working with 7dBi gain antennas），can connect the different gain
antennas like 9dBi、12dBi etc，can identify the tag which moving speed is
120km/h correctly.；
5、 Tag identify speed ：
Single tag 2000 times/minute ， multi-tag
200pcs/second；
6、 Can connect to 1 to 4 same gain and different gain planar antennas via
high-frequency cable. To expand the identify area of tag and reduce the
hardware cost for customer. The RF power of the antennas can set from 0
to 31dBm in separate；
7、 Reader will detect antennas when it get power. In case to protect antenna
port. The one has no antenna connect will not send RF power.；
8、 Have RS232、RS485、 Weigand、TCP/IP、Relay etc output interface；
9、 Compatible with tag match function，Reader can identify the tag which
match the condition or not identify these condition tags by setting the
match conditions.；
10、Compatible with data cache function, Using FRAM (ferroelectric memory)
which can save data when power down，memory capacity is 32KBytes，
Can save 2200 pcs tag data in 12 Bytes data length.
2.3 Reader applications
This reader are widely use in various RFID system，reference application as
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
10
below：
1、 Logistics and warehouse Management: Goods flow, warehouse
management, and the flowing management of mail, parcel, luggage.
2、 Intelligent parking Management :Parking management and automatic
charge
3、 Productive lines Management: Production process fixed Identify
4、 Product counterfeit-proof inspection: Using memory’s write-protect
functions inside tags, and identifying with true-false of products
5、 Other fields: Used widely in club management, library, student’s school,
consumption management, time management, dinner management, pool
management
2.4 Reader main functions
1、 Read tag data：Can read multi-tag same area and same data length in a
same time；
2、 Write tag：Can write the same data length in multi-tag’s same area.；
3、 Tag match：Can read match tag or dismatch tag via setting the match
conditions；
4、 Make data communicate and change with the connection between
standard communication interface and controller or PC,；
2.5 Reader technical parameter
1、 CompatibleISO18000-6B and ISO18000-6C(EPC-GEN2) protocol
standard；
2、 Working frequency：fixed-frequency can choose ISM 902～928MHz
（America）、ISM920～925MHz（China）和 ISM 865～868MHz（Europe）
；
Can also customer made other frequency from ISM 900～930MHz，
stepped frequency is 250KHz；
3、 Reading range：Reading from 0~10 meters (working with 7dBi antenna)；
4、 Tag identify speed： Single tag 2000 times/minute，multi-tag
200pcs/second；
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
11
5、 Trigger working mode：Timer and I/O can trigger reader，Timer interval
from 10-990ms；I/O trigger MAX time is 255s；
6、 Data pre-processing：On trigger working mode，Tag data can store in
cache or output directly.；
7、 Data cache：Trigger working mode data cache using FRAM (ferroelectric
memory) which can save data when power down，memory capacity is
32KBytes，Can save 2200 pcs tag data in 12 Bytes data length；
8、 Data output：Data return by instant messaging，Can config RS232、RS485、
Weigand、TCP/IP、Relay interface, Can config output data length and start
address，Output data format in ASCII；
9、 Compatible ISO18000-6C tag match function ， match tag by setting
conditions；
10、For ISO18000-6B tag. Can do read, write, lock and identify operate to
single tag one
byte ，can read and write specific tag data with UID；
11、Dimensions：354.00mm（length）*210.00mm（width）*38.00mm（heigth）
；
12、Working voltage：DC+9V～+15V；
13、Working temperature：-20℃～+60℃；
14、Storage temperature：-40℃～+85℃；
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
12
3 Reader Structure and Interface Explanation
3.1 Reader Structure Explanation
1、 Reader circuit function
PLL
frequency
generator
power
amplifier
90 degree transmission
line
Diode passive mixing
4V LDO
Active low
pass
filter
5V LDO
Analog
switch
Capacitor
Differential
amplification
3.3V LDO
comparator
Micro controller
12V-5.5V
DC/DC
Stepdown
circuit
Power
RS232
interface
chip
RS485
interface
chip
GPIO drive
DB15
Hardware
protocol stack
network chip
RJ45
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
13
2、 MR6261A Desktop reader structure explanation
3、 MR6211A、MR6221A integrated reader structure explanation
3.2 Explanation on the reader communication interface
1. RS232: the Reader provides standard RS232 communication interface as
the output port for data modulation. RS232 has 8 data bits format: 1 start bit
and 1 stop bit, no parity bit. The default baud rate is 115200 bps. The
interface supports the reader parameters configuration, software upgrading,
demo program and all functions for series communication with
development kit with functions package；
2. RJ45（Ethernet Port）
：100M Ethernet，TCP Server Mode; It is main mode
for connecting communication with PC，also can be data output main
mode ， The interface supports the reader parameters configuration,
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
14
software upgrading, demo program and all functions for TCP/IP
communication with development kit with functions package；
3. Data Interface DB15 diagram and pin definition
4. RS485：Reader provide RS485 communication interface（10、11 pin），
work as data main output mode，also can connect with PC via serial port，
use RS232-RS485 converter，in this way，RS485 interface support RS232
all supported functions;
5. Programmable output interface ： Two sets TTL electrical level
programmable output interface（1、2 pin），works as Wiegand output
interface，default is high level（5V）；one set relay interface（13、14、15
pin），relay default status is OFF and COM short circuit
6. Input check port：2 team input check port（7、8 pin），can configure as trigger
read mode，default as Dangling status is high level（5V）；
7. Power supply port：DC+9V～+15V==4A power port；
8. Antenna port：4 sets TNC antenna port；
9. Indicator light：6 indicator light，including COM port indicator light、power
indicator light and 4 sets antenna indicator light；
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
15
4 Quick Start Guide
1、 Connect antenna to reader’s antenna port（one antenna or multi-antenna
applicable, maximum 4 antennas），connect power adapter to reader and
then power on，connect reader to LAN or PC by network cable；
2、 In PC open demo software“MR62XX Demo V1.0”，fill in reader IP address
and click“Connect”to connect reader（reader factory default IP address:
192.168.1.200）；
3、 After reader connection, it will automatically detecting antenna and
transmit power query，in“Setting”page selecting detected antenna port
（green icon）and click“Set”button，set corresponding port’s
transmit
power and click“Set”button，see below：
4、 In“Gen2 EPC MultiTag” page，click bottom right corner“Identify”button will
start EPC tag query operation，see below：
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
16
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
17
5 Reader parameter configuration
5.1 Webpage configuration
Reader connect to LAN through TCP/IP port，or directly connect PC，in PC
IE browser input reader IP address （ reader factory default IP address:
192.168.1.200），after running then open WEB page as below：
Can be configure as below：
1、Basic Item configuration
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
18
1）User can configure IP address、RF power、frequency、antenna port、applied
mode、read card indicating etc.,
2）Each antenna port RF power can be configurable, range: 0-31dBm；
3）Frequency standard: China Frequency、US Frequency、EU Frequency
three type standard hopping frequency selectable；
4）Applied mode:“Favor speed” and“Favor quantity” two mode
selectable“Favor speed” for single tag or small batch tags quick speed read
mode；
“Favor quantity”for big batch tags read mode；
2、Operating mode configuration
1）In operating mode configuration, user can configure reader to be timming
working mode or pin trigger working mode，timer’s timing interval can be
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
19
configure between 10-990ms；When in trigger working mod, reading
maximum lasting time can be configure as 255s；
2）Read tag type can be 18000-6B or EPC G2，also can be configure read both
at same time（expand function）；
3）When read EPC tag，read area can select as EPC、TID or USER memory；
6B tag cannot select area；
4）User can select read tag’s start address and read data length，EPC tag data
use word as unit，6B tag data use byte as unit;
5）User filter repeat tag，Filter set one slide time window，only new data which
not show in box can be buffer or direct output；
6）Read tag data can be select buffer or directly output，data buffer adapt with
power down save ferroelectric memory，storage capacity 32KBytes，when read
data length is 12Bytes，can store more than 2200pcs tag data；
3、output configuration
1）In working mode configure, when select data output as directly output mode,
user can configure output port；
2）Reader data output port have RS232、RS485、Wiegand、Ethernet and relay
output；
3）Wiegand protocol support Wiegand26 and Wiegand34；
4）Relay close delay time configurable between 0-99s；
5）For above mentioned port, user can select one type or multiple type to
output data；
6）Data output as ASCII code format；data format see below：
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
20
All above configuration will be valid only after click left bottom
button“set” button
5.2 Demo software Configuration
5.2.1 Reader connection
Click MR62XXDemo.exe software, input reader’s IP into the IP input box
(Default IP: 192.168.1.200, Port: 100 which is fixed), then click ‘connect’ ICON,
software information display box will display the reader’s parameter on the
success connection. Below image demonstrate the success connection.
5.2.2 Antenna & RF Power setting
1 On MR62XXDemo.exe software’s Setting interface, query and set Antenna’s
RF Power on Power setting; Query and set Antenna on Antennas Setting. Take
below image for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
21
2、Set the 4 antenna ports RF power separately from the range of 0 to 31dBm.
3、On the reader connection, the antenna port will begin self detection, and the
connecting Antenna port is on GREEN ICON, Disconnecting Antenna port is
on RED ICON. Only the selected GREEN ICON port’s antenna works.
4、 On Integrated RFID reader and Desktop RFID reader, config and set one
antenna port for the reader to work.
5.2.3 Frequency Setting
On MR62XXDemo.exe software's Setting interface, Query Reader’s
Frequency on Frequency setting menu, there are China Frequence
(920-925MHz), North America Frequency (902-928MHz), European frequency
(865-868MHz), and others frequency
configurable. China, North America,
and European Frequency type are in FHSS working mode. Select Fixed
frequency or multi fixed frequency working mode on the others frequency type,
take below images for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
22
5.2.4 Working Mode Setting.
1、On setting interface’s Working Mode Setting, there are two working mode,
Favor speed and Favor quantity for the query and setting, take below image for
the reference.
2、Favor speed is for single tag or few tags reading with the high speed tag
reading rate. Favor Speed working mode is configurated for the applications
require high speed tag reading rate (e.g. Not-stop Highway toll)
Favor Quantity is for the multi and tense tags reading, Favor Speed working
mode is configurated for the applications (e.g. warehouse, logistic)
3、If the reader is configurated into Favor speed working mode, it’s invalid for
the Matched EPC tag reading.
5.2.5 Buzzer & LED Setting
1、On Setting interface’s Buzzer & LED Setting menu for Querying and Setting
Buzzer & LED ON/OFF. Take below image for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
23
2、After setting Buzzer & LED ON/OFF, Reader automatically reset, and need
to reconnect the reader.
5.2.6 IP Address Setting
1、On setting interface’s TCP Parameter Setting menu for querying and setting
reader’s IP, take below image for the reference.
2、Reader automatically reset when set a new IP address, and need to
reconnect the reader with new IP address
5.2.7 GPIO Setting
On Setting interface’s Set Out Port menu for the reader output port setting.
The reader has two sets output port and one set Relay port. IO Port0 and IO
Port1 are output port with default High level voltage (5V) and Low level voltage
(0V) configurable. IO port2 is Relay output port with default OFF setting. take
below image for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
24
6 Demo software demonstration
6.1 EPC Gen2 tag Demonstration
6.1.1 Multi tag Identify
1、On Gen2 EPC Multi Tag interface’s Identify menu for the Multi tag identify,
and click Identify ICON to start the reading. EPC code, antenna number and
tag reading times displayed on the interface info. box. On the interface bottom
displays tag number, Peak reading rate, Read times, total reads, Average
reading rate, and duration reading time. Take below image for the reference.
2、Click ‘Stop’ ICON for stopping tag identify.
3、Click ‘ Once’ ICON for sending once tag detect command, and returns the
tag number,
take below image for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
25
6.1.2 Multi Tag Read & Write
1、On Gen2 EPC Multi Tag interface’s Multi Tag Read menu for the Multi tag
read, Multi tag reader is read tag’s RESERVE Membank, EPC Membank, TID
Membank & USER Membank at the same time. The steps are: 1) select the
reading Membanks, 2) select the start reading address and the reading word
count (EPC tag’s unit is word), and then click ‘Read’ ICON to start the Multi-tag
reading. Take below image for the reference.
2、Click ‘Stop’ ICON to stop Multi-tag reading, at the bottom of the demo
software interface display the tag number, and the reading duration time.
3、On Gen2 EPC Multi Tag interface’s Multi Tag Write menu for Multi tag
encoding. Multi-Tag Write is to encode the tag’s Reserve Membank, EPC
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
26
Membank, and USER Membank at the same time. The steps are: 1) select the
encoding Membank, 2) select the tag start encoding address and the encoding
word count (EPC tag’s unit is word), 3) input the encoding value, then click
‘Write’ ICON to encoding the multi-tag. Take below image for the reference.
4、Click ‘Stop’ ICON to stop the Multi-Tag encoding, at the bottom of the demo
software display the Success encoding tag number, and tag encoding duration
time.
5、In accordance with the EPC Protocol, On Multi Tag Read & Multi Tag Write,
EPC Membank’s Start reading address and Start encoding address is from the
EPC Membank’s Second word address.
6.1.3 Tag Filter
On Gen2 EPC Single Tag interface’s Gen2 Select Config menu for the Tag
Filter rule setting. Tag Filter setting rule is based on the EPC Membank, TID
Membank or USER Membank value for the setting condition. In accordance
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
27
with the EPC Gen2 Protocol, RESERVE Membank’s data is invalid for the tag
filter rule setting. Please 1) select the EPC tag Membank, 2) the word addr. 3)
Word Length, 4) Input the value, then Click ‘Config’ ICON for the Tag filter rule
setting.
1、Only on Favor quantity working mode, the Tag filter setting is valid, on Favor
speed working mode, tag filter setting is invalid.
2、Match setting, reader reads and displays only the condition matched tag.
3、Mismatch setting, Reader doesn’t read and display the condition matched
tag.
4、Empty the input value for cancel the Tag filter rule.
5、If setting EPC Membank as the Tag filter rule, the valid Word Addr is 2.
6、After set the EPC tag filter rule, this rule is valid for all EPC tag detect.
7、After set the EPC tag filter rule, this rule is valid for all the time unless the
reader is power off or reset.
6.1.4 EPC Gen2 Tag Lock
1、On Gen2 EPC Single Tag interface’s Gen2 Secured Lock menu for the EPC
Gen2 Tag Lock setting. With Access Password, it can lock Reserve Membank,
EPC Membank, and USER Membank in different lock level. Take below image
for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
28
2、EPC Gen2 Tag Lock level are unlock, unlock forever, and secure lock, lock
forever
1）Unlock means the tag is not to encrypted the tag
2）Unlock forever means the tag will not be locked forever
3）On Secure Lock, RESERVE Membank only can be read and write with
Access Password, EPC Memban and USER Membank can be encoded
with Access Password.
4）Lock forever, if the tag is set to lock forever, it can’t be unlock again.
6.1.5 EPC Gen2 Tag Read and write with Access Password
1、n Gen2 EPC Single Tag interface’s Gen2 Secured Read and Gen2 Secured
Write menu for the EPC tag reader and write with Access password. Take
below image for the reference.
1）Gen2 Secured Read with Access password
2）Gen2 Secured Write with Access password.
2、EPC Gen2 Secured Read with Access password need to input the Select
Read tag’s Word Addr, and the WordCnt.
3、EPC Gen2 Secured Write with Access password need to input the Select
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
29
Write tag’s Word Addr, and the WordCnt
4、Secure locked Reserve Membank can only be read & write with Access
Password, Secure Locked EPC Membank and Secure Locked USER
Membank can be encoded with Access Password, while can read without the
Access Password.
5、 In accordance with the EPC Protocol, TID Membank can’t be locked,
Access Password is invalid for TID Membank.
6.1.6 EPC Gen2 Tag Kill.
1、On Gen2 EPC Single Tag interface’s Gen2 Kill menu for the Tag Kill
password to kill the tag, Take below image for the reference.
2、EPC Gen2 tag can’t be read and write if the tag is killed.
6.2 ISO18000-6B Protocol tag Demonstration
6.2.1 ISO18000-6B tag Identify
On ISO 6B interface for the ISO18000-6B tag Identify. Click ‘Identify’ ICON
for the tags Identify, and the software interface displays the ISO18000-6B tag’s
UID code, Antenna No., and the read times. Click ‘Stop’ ICON for stoping the
tag Identify. Take below image for the reference.
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
30
6.2.2 Multi-tag user data reading
Put several 6B tags in the radiation range of antenna，in the ISO 6B
operation interface，choose Multi Tag Read to enter into multi-tag data reading
interface ， choose the start address of data that you want to read,then
click“Read”button to operate multi-tag data reading，the interface will indicate 8
bytes data from start address、antennas numbers and times to be read，like
following picture indicates，click“Stop”button to stop user data reading；
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
31
6.2.3 Single tag data reading and read with UID
1、In
the ISO 6B operation interface，choose Single Tag to enter into single
tag operation interface，choose the start address of data you want to read in
the ISO Read menu item，click“Read”button to start reading data，the
interface will indicate the tags data that is read，the data length is 8 bytes data
from start address：
2、When data read with UID，it needs to know the UID of the tag first，you can
set the start address to 0 when query UID，the reading data is tag UID，after
inputting UID，choose the start address of reading data，click“Read With
UID”button to operate data reading：
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
32
6.2.4 Single tag writing and write with UID
1、Single Tag operation interface，choose the data address you want to write in
the ISO Write menu item，click“Write”button to write data；
2、When operate writing data with UID，except for inputting the single byte data
that needs to write，it also needs to put the UID number of tag，choose the
start address that want to write，click“Write With UID”button to write data；
6.2.5 Single tag data lock
1、Single Tag operation interface，choose the data address you want to lock in
the ISO Lock menu item，click“Lock”button to lock data，if return “ISO Lock tag
success” in “Result”column,it means lock successfully：
2、It is unable to rewrite data in the address that is successfully locked；
6.2.6 Single tag lock and query
Single Tag operation interface，choose the data address you want to query in
the ISO Query Lock menu item，click “Query”button to lock and query，it will
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
33
return query result in “Result” column，like“Had locked”and“Not lock”；
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
34
7 Reader struction and installation sketch map
1、 MR6134E reader Appearance & CAD Structure Chart：
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
35
2、 MR6161 desktop reader Appearance & CAD Structure Chart:
3、 MR6134E reader installation sketch map：
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
36
Notice：MR6134E can connect with 4 antennas，every antennas installs in
different position to read tags on goods better。
4、MR6111、MR6121 integrated reader installation sketch map：
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
37
8 Secondary development
User can make secondary development for reader application software if
needing.
We provide SDK，which supports VC++、C#、JAVA and so on，the use of
SDK,please refer to《MR62XX serial reader SDK instruction》。
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com
◢MR62XX Serial UHF reader user manual（Ver 1.0）◣
38
9 Common faults and exclusion methods
Failure Description
Simple exclusion methods
■make sure the power adapter indicator light is on
Unable to start reader
■make sure the reader power interface is connected well
Unable to connect ■make sure the reader IP address is correct
reader
■make sure the network environment is good
Reader is unable to ■make sure antenna ports are connected correctly
identify tag
■make sure antenna power is not to be 0
No
sound
when
■make sure the buzzer is open
reading tag
■make sure that when tag operates with password,the
Tag with password
radiation range of antenna is single tag or small amount
operation failed
of tags
Invalid
tag
filter
■make sure the reading mode for reader is multi-tag read
settings
Unable to refresh the
■Clear CGI in the web address or re-enter the IP address
page in the web
of the reader and refresh
configuration
Address：
Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen, P.
R.C. Post：518057
Phone：0755-2654 6392
E-mail：technical@marktrace.com
FAX：0755-2655 3743
Website：www.marktrace.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : GHOST
Company                         : P R C
Create Date                     : 2017:10:26 17:37:02+08:00
Modify Date                     : 2017:10:26 17:37:16+08:00
Source Modified                 : D:20171026093623
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2017:10:26 17:37:16+08:00
Creator Tool                    : Acrobat PDFMaker 9.1 Word 版
Document ID                     : uuid:73bbd831-a9ca-41dd-835d-ae4d7cc0a470
Instance ID                     : uuid:f945b81b-835c-4918-981b-b64fcf7649be
Subject                         : 2
Format                          : application/pdf
Title                           : MSR-A2移动智能识读器用户手册
Creator                         : GHOST
Producer                        : Adobe PDF Library 9.0
Page Layout                     : OneColumn
Page Count                      : 38

EXIF Metadata provided by EXIF.tools