MEIAN Technology MD-210R Wireless magnetic contact User Manual

Shenzhen Meian Technology Co.,Ltd . Wireless magnetic contact

User Manual

Model:MD-210RWireless sending distance(open area):inset antenna 150m.Code: 28-digi t ID, 8-digit function code, 36 digits data code in totalWorking frequency: 433MHz(optional)Working voltage:3V lithium batteryBattery life: about 1 yearCurrent: static 5uA, alarm:7-12mA (433MHz) static 5uA, alarm:35-45mA Note This product use Cr123 lithium battery no battery set in when leave factory please set in battery before using. 1 Press lightly the snap near the led, and open the cover;2 Set in battery with right positive and negative poles; 3 code with the panel A Set the wireless control pane at "auto code" mode. B Let MD-210R enter working mode parallel put transmitter and magnetic stripe together, move the magnetic stripe at the moment of pressing the ensure key on the panel and let the detector send wireless signal. Then the panel will study the code of detector. Product appearanceWhen use as wireless detector, do not mount near strong magnetismitem.Do not mount at the loose placeDo not mount on the place possiblely to be destroyed outdoor.Indication LEDTransmitterMagnetic stripe Alarm output: alarm, tamper3.2 InstallationPay attention to these following points.3.3 Installation introduction The MD-210R is a fully supervised mini style magnetic contact transmitter. It features door/ window close/openinstant alarm function. It can be connected to the controlpanel. It can transmit strong wireless signal, having strong intensity in 15m area. Pleas code it to the control panel before using, enrolling the only one address code to the control panel. When the distance between the magnetic stripe and transmitter beyond 2.5cm the transmitter will send alarm information to the panel. Thisdetector can change wired signal to wireless signal, 1. Introduction A. Adopted low consumption CPUB. Adopted unique Mutil codesC. Auto status reportBuzzer The installation guide for users of MD-210R wireless magnetic switch D. Anti-lost reportE. Open door/window indication Status report after fist electro motion or reset the detector the magnetic switch report the working status to the control panel separately after 30 seconds, 2 minutes,6minutes. And report working status every two hours to the control panel.Color: WhiteWorking Temeprature:-10 ~50Dimesion:81(L) 32(W) 25(H)mm Magnetic stripe:74.5 (L) (W) (H)mm2. Specification3.1 Main functions 3.The main function and installationWorking as a transmitter.
P/N 20101217-3 C The user also can enter address code manually, that will reduce error rate, set the control panel at manual code mode , then enter the 9-digit code on the label of transmitter. 4 Testing magnetic switch parallel move magnetic stripe and inductor. MD-210R will send signal once to the control panel, and the LED on the transmitter flick 5 times.5 Fix the cover4 Install follow the pictures 1.If not drill on the wall please use strong double side glue or other strong Bonding agent to fix the magnetic stripe and transmitter on the right place. 2. Do not mount on the base-loose place, possible to be destroyed place or with strong magnetic interference(eg.loudspeaker, high voltage cable)NoteChoose short circuit place whenmagnetic fix on the R side of reed switch. The jumper jump to theR side of contact pin.When use as detector, these jumper keep opening.Choose short circuit jumper:when magnetic fix on the L side of reed switch. The jumper jump to the L side of contact pin.when use as transmitter, connect the alarm terminal to the wired terminal of the magnetic.Wired terminalWhen use as transmitter,these jumperkeep shortcircuit.6. Miscellaneous Comments Our wireless products are very reliable and tested to high standards. However, due to low transmitting power and limited range(required by regulatory authorities , there are some limitations to be considered. it will course the panel to make alarm at any alarm situation, following are some common examples 1. voltage instability for the control panel; 2.under voltage of detector etc. These problem are not so difficult to solve, if needing help please contact the supplier. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4.1 Change battery The working life of battery is about one year change battery when the signal between the detector and control panel become weak. 1.Open cover; 2.Take out used up battery and put in new battery rightly; 3.Test battery, parallel move the magnetic from transmitter, then the control panel will make alarm information.4.2 Clean and fix the cover The surface of the detector will be dusty when used for a long time, please use wet cloth to clean it.5.maintanceOpen loop is NO;Close loop is NC.

Navigation menu