MEILOON CPS Wireless Speaker Amplifier User Manual Wireless Speaker Amplifier
Meiloon Industrial Co., Ltd. Wireless Speaker Amplifier Wireless Speaker Amplifier
MEILOON >
Users Manual
Wireless Speaker Amplifier
Owner’s Manual for OEM
Caution: This user guide information is only provided to OEM or module installer.
Do not supply to end user.
1. Introduction
The CPS 8Wi Wireless Speaker Amplifier is a radio device that transmits and receives
radio signals in accordance with the spectrum regulations for the 2.4GHz unlicensed
frequency range. The following table shows a major function.
Frequency Band: 2403.3~2479.1MHz
Power Supply: DC 12V from the testing board
Channel Employed: 20 channels
Modulation technology: FHSS
Modulation Type: FSK
Antenna Type: Dipole Antenna
Radio Frequency Chipset: WHAM2 Module
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following “Contains
TX FCC ID: R48CPS
If the size of the end product is larger than 8x10cm, then the following FCC part
15.19 statement has to also be available on the label: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter.
IMPORTANT NOTE:
This equipment complies with IC RSS-102 and FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
OEM integrator is still responsible for testing their and product for any additional
compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example
certain laptop configurations or co-location with another transmitter), then the IC
authorization is no longer considered valid and the IC No. cannot be used on the final
product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate IC
authorization.
20cm minimum distance has to be able to be maintained between the antenna and the
users for the host this module is integrated into. Under such configuration, the FCC
radiation exposure limits set forth for an population/uncontrolled environment can be
satisfied.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and
operated. The end user has to be informed that the FCC radio-frequency exposure
guidelines for an uncontrolled environment can be satisfied. The end user has to also
be informed that any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate this equipment. If the size of
the end product is smaller than 8x10, FCC part 15.19 statement is required to be
available in the users manual: This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following “Contains
TX FCC ID: R48CPS.
If the size of the end product is larger than 8x10cm, then the following FCC part
15.19 statement has to also be available on the label: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.