User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1303093 |
| Application ID | E4/ZrNUifMNuvjoNAh4GmA== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 10.94kB (136767 bits) |
| Date Submitted | 2010-06-28 00:00:00 |
| Date Available | 2010-06-28 00:00:00 |
| Creation Date | 2010-06-14 17:45:09 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2010-06-14 17:45:09 |
| Document Title | untitled |
■ How to input a operating distance Wireless Transmitter ■ How to set up waiting time (Motion sensor, Door sensor) ■ Wireless Transmitter (WT-200NF) 1) If the code is inputted by “Armed” button on remote control: When it receives radio waves, immediately sends radio waves. Thank you for purchasing our product. Please read carefully the instruction guide to use the product more safely and effectively. This is a wireless transmitter which receives the detection signal from emergency switch, remote controller or sensors and send the signal to receiver (WR-200,WR-300) 2) If the code is inputted by “Off” button on remote control: When it receives radio waves, sends radio waves after 16seconds. WT-200NF has function that it is operated by emergency signal of master remote control within preinputted operating distance and it only operates the nearest transmitter if it uses with several transmitters. - Motion sensor, Door sensor: (Operating distance is inputted by special remote control) If transmitter is armed - when signal is received, it transmits the signal to the receiver after 16 seconds (or immediately) After plugging the power, press “Emergency” button of special remote control (within 8 seconds) from a distance you are wanted as shown in the picture ※ If transmitter is OFF, it does not receive a signal ■ Connect and operate with wired siren (option) WT-200NF ■ Product component sensor, Gas sensor: When emergency or sensor signal is received, immediately transmits the signal to the receiver. 1 wireless transmitter, 1 adaptor, 2 screws, 1 manual Remote control ■ How to input a code Operating distance: Maximum 15m After plugging the power, press the transmitter power ON switch using ball pen or sharp pin then the red light will blink. At this moment (within 8 seconds), press the ‘security’ button of the remote control more than 2 seconds, then code can be inputted lighting the red lamp. After input operating distance, Emergency signal of special remote control is possible to operate within pre- operated distance Switch (※Caution: It may not operate in a building because of obstacles within operating distance.) ■ How to install ※ Master remote control: Operate all wireless transmitter (If input a code of master remote control to each transmitter) ※ Remote control: Operate only one registered transmitter (Input a code of remote control each transmitter) ※ Input a code number of remote control to receiver ※Input maximum 254 different codes and display location of transmitter based on the each code Although range is 800m between transmitter and receiver, decrease receive range because some obstacle if it is installed in a house or building. Therefore, position a transmitter and check operation several times before installation. ※ Range of radio wave depends on structure inside building and ambient temperature (Wall, Floor, furniture, furnishing and etc.) ※ Installation location of transmitter please install 70% of distance which can be received signals(Field Test) (Example: If the signals can be received 70m between transmitter and receiver, place it 50m) ■ Operation Armed – Press the “ARMED” button of a remote control for 2seconds, it makes sound “beep - beep” and blinks red lamp every seconds for 32 seconds and turn off the red lamp. OFF - Press the “OFF” button of a remote control more than 1 second, it makes a “beep” and turn on red lamp ［Operation after received detected signal of optional sensor］ - Emergency button of remote control, Fire detection WT-200NF RC-200F - Motion sensor, Door sensor: If transmitter is armed - when signal is received, ring the siren for 32 seconds after 16 seconds (or immediately) ■ Product specification - Transmission distance: approximately 200m ~ 800m (depend on obstacle) - Power supply: dc 12v power adapter - Size: 112mm x 66mm x 20mm, - Weight : 77g EMERGENCY - Press the “EMERGENCY” button more than 1 second of a remote control, It makes sound “beepbeep-beep” and transmits emergency signal ARMED + OFF – Press the “ARMED and OFF” button of a remote control, It makes sound “beep” and transmits signal WR-200 - Emergency button of remote control, Fire detection sensor, Gas sensor: When emergency or sensor signal is received, immediately ring the siren for 32 seconds. ■ Option Remote control, Emergency switch, wired siren, pendant emergency switch, door sensor, smoke sensor, gas sensor, motion sensor. ■ Warning Change or modifications not expressly approved by manufacturer could void the user’s authority operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Modify Date : 2010:06:14 17:45:09+09:00 Create Date : 2010:06:14 17:45:09+09:00 Format : application/pdf Title : untitled Document ID : uuid:cea9487f-50a8-46a0-aae3-c16ffb358034 Instance ID : uuid:1e61481b-6796-4cef-a706-7cf89ad63b11 Page Count : 1EXIF Metadata provided by EXIF.tools