MOBOTIX BELLC RFID access control system User Manual BellRFID Regulatory Notice US
MOBOTIX AG RFID access control system BellRFID Regulatory Notice US
MOBOTIX >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3894613 |
| Application ID | azI7X+eHT9VLohAj8P2JUg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 64.45kB (805664 bits) |
| Date Submitted | 2018-06-20 00:00:00 |
| Date Available | 2018-06-20 00:00:00 |
| Creation Date | 2018-06-15 10:47:11 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2018-06-15 10:47:20 |
| Document Title | BellRFID – Regulatory Notice – US |
| Document Creator | Adobe InDesign CC 13.1 (Macintosh) |
| Document Author: | Thilo Schüller, MOBOTIX AG |
Accessories MX-Bell1-Button-F2 MX-Bell1-Button-F3 MX-Bell1-Button-F4 MX-Bell1-Button-05 MX-Bell1-Button-XL1 MX-AdminCard1 MX-UserCard1 MX-BellC-Core-EXT BellRFID Regulatory Notice 31.579-003_US_06/2018 MX-Bell1-Button-F1 Federal Communications Commission (FCC) and Industry Canada (IC) Notice for MX-BellC-Core-EXT (PMN: BellRFID) (FCC ID: YYRBELLC, IC ID: 9357A-BELLC) NOTICE: This device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. NOTICE: Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence. L‘exploitation est autorisée aux deux conditions suivantes: 3. l‘appareil ne doit pas produire de brouillage, et 4. l‘utilisateur de l‘appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d‘en compromettre le fonctionnement. NOTICE: Changes or modifications made to this equipment not expressly approved by MOBOTIX AG may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Radiofrequency Radiation Exposure Information: The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. Ministry of Internal Affairs and Communications Notice for MX-BellC-Core-EXT NOTICE: • This device has been granted a designation number by Ministry of Internal Affairs and Communications • This device should not be modified (otherwise the granted designation number will be invalid) Declaration of Conformity Notes • Please follow the notes on installing and operating the device in the MOBOTIX T25 System Manual (www.mobotix.com in the Support > Download Center > Documentation > Manuals section). • The MOBOTIX BellRFID is only to be used in the original frames of the IP Video Door Station. • Before Installing, make sure that the seal on the back of the BellRFID has been properly attached. • When inserting the module into the frame, only press at the edge, never at the center of the module. • Make sure the device is not operated outside of its operating temperature range of –30 to +60°C/–22 to +140°F. Dimensions Back 99 mm/3.9 in 99 mm/3.9 in Cindy Jones Thomas Jones The Jones Family Dr. Jones, MD Importer: Further information on www.mobotix.com: • Products > Access Control > IP Video Door Station > T25 Outdoor Station and Access Module • Support > Download Center > Documentation > Certificates & Declarations of Conformity MOBOTIX, the MX logo, MxPEG and MxActivitySensor are trademarks of MOBOTIX AG registered in the European Union, the U.S.A., and other countries • Information subject to change without notice • MOBOTIX does not assume any liability for technical or editorial errors or omissions contained herein • All rights reserved • © MOBOTIX AG 2018 MOBOTIX Corp. 80 Broad Street, Suite 702 New York, NY 10004 U.S.A. Phone: +1 (212) 385 6126 Fax: +1 (212) 385 6129 us-sales@mobotix.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Language : de-DE XMP Toolkit : Adobe XMP Core 5.6-c143 79.161424, 2017/09/22-11:52:47 Format : application/pdf Rights : Copyright © 1999 – 2018, MOBOTIX AG Title : BellRFID – Regulatory Notice – US Creator : Thilo Schüller, MOBOTIX AG Metadata Date : 2018:06:15 10:47:20+02:00 Modify Date : 2018:06:15 10:47:20+02:00 Create Date : 2018:06:15 10:47:11+02:00 Creator Tool : Adobe InDesign CC 13.1 (Macintosh) Instance ID : uuid:661c85df-2e30-134e-b887-283d5ab4d0b8 Original Document ID : xmp.did:0780117407206811AB08A3F0AEF9B5E5 Document ID : xmp.id:58e3776e-ffde-4d5c-9598-fe0453bca947 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:888efa09-40f2-4865-b2c9-5dd0e73fb06b Derived From Document ID : xmp.did:FC7F11740720681197A58AEB88B97BDA Derived From Original Document ID: xmp.did:0780117407206811AB08A3F0AEF9B5E5 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.1 (Macintosh) History Changed : / History When : 2018:06:15 10:47:11+02:00 Caption Writer : Thilo Schüller; MOBOTIX AG Marked : True Producer : Adobe PDF Library 15.0 Trapped : False Page Layout : TwoPageRight Page Count : 2 Author : Thilo Schüller, MOBOTIX AGEXIF Metadata provided by EXIF.tools