MOBOTIX KPADC RFID access control system User Manual KeypadRFID Regulatory Notice US

MOBOTIX AG RFID access control system KeypadRFID Regulatory Notice US

Users Manual

MX-KeypadC-EXT KeypadRFIDRegulatory Notice31.287-004_US_06/2018Federal Communications Commission (FCC) and Industry Canada (IC) Notice for MX-KeypadC-EXT (PMN: KeypadRFID)(FCC ID: YYRKPADC, IC ID: 9357A-KPADC)NOTICE:This device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation is subject to the following two conditions:1. this device may not cause harmful interference, and2. this device must accept any interference received, including interference that may cause undesired operation.NOTICE:Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence. L‘exploitation est autorisée aux deux conditions suivantes:3. l‘appareil ne doit pas produire de brouillage, et4. l‘utilisateur de l‘appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d‘en compromettre le fonctionnement.NOTICE:Changes or modications made to this equipment not expressly approved by MOBOTIX AG may void the FCC authorization to operate this equipment.NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interfer-ence by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Radiofrequency Radiation Exposure Information:The radiated output power of the device is far below the FCC radio frequency exposure limits. Never-theless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.Ministry of Internal Aairs and Communications Notice for MX-KeypadC-EXTNOTICE:• This device has been granted a designation number by Ministry of Internal Aairs and Communications• This device should not be modied (otherwise the granted designation number will be invalid)AccessoriesMX-AdminCard1 MX-UserCard1
Importer:MOBOTIX Corp. 80 Broad Street, Suite 702 New York, NY 10004 U.S.A.Phone: +1 (212) 385 6126 Fax: +1 (212) 385 6129 us-sales@mobotix.comFurther information on www.mobotix.com:• Products > Access Control > IP Video Door Station > T25 Outdoor Station and Access Module• Support > Download Center > Documentation > Certicates & Declarations of ConformityMOBOTIX, the MX logo, MxPEG and MxActivitySensor are trademarks of MOBOTIX AG registered in the European Union, the U.S.A., and other countries • Information subject to change without notice • MOBOTIX does not assume any liability for technical or edi-torial errors or omissions contained herein • All rights reserved • © MOBOTIX AG 201899 mm/3.9 in99 mm/3.9 inDimensions BackNotes• Please follow the notes on installing and operating the device in the MOBOTIX T25 System Manual (www.mobotix.com in the Support > Download Center > Documentation > Manuals section).• The MOBOTIX KeypadRFID is only to be used in the original frames of the IP Video Door Station.• Before Installing, make sure that the seal on the back of the KeypadRFID has been properly attached.• When inserting the module into the frame, only press at the edge, never at the center of the module.• Make sure the device is not operated outside of its operating temperature range of –30 to +60°C/–22 to +140°F.Declaration of Conformity

Navigation menu