MS Sedco CP-TX DUAL FREQUENCY R/C TX User Manual CP TX Inst

Download:
Mirror Download [FCC.gov]
Document ID	336602
Application ID	GoRN9FTbLMqAXMjAefhQ+g==
Document Description	MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.11kB (101407 bits)
Date Submitted	2003-07-01 00:00:00
Date Available	2003-07-01 00:00:00
Creation Date	2003-04-15 08:58:29
Producing Software	Corel PDF Engine Version 9.397
Document Lastmod	2003-04-15 08:58:29
Document Title	CP-TX Inst.cdr
Document Creator	CorelDRAW Version 9.397
Document Author:	J. Kelley Isenhower

CP/TX
INSTALLATION INSTRUCTIONS
Universal 300/390 MHz Transmitter with Surface Mounting Box
S ection 1
General Description
The CP/TX radio transmitter is designed to provide reliable WIRELESS activation of any automatic door. It is part of
the most extensive line of programmable wireless products available and compatible with MS Sedco switches.
The CP/TX radio transmitter is a universal unit which can operate in either the 300MHz or 390MHz systems.
The CP/TX comes with the transmitter prewired and installed in the mounting box for easy installation. One screw
access also allows for easy battery placement.
S ection 2
Basic Installation
1) Drill at least two holes in the box back plate and secure it to its intended location.
2) If the weatherproof gasket (MS Sedco #10001) is to be installed, apply per the instructions provided with it.
3) Secure the door activator switch assembly (purchased separately) to the box frame with two #6-32 screws
(provided with the switch).
NOTICE: Drill out pilot holes when necessary to mount door activator switch.
4) Program the transmitter, located in the box frame, by setting the 12 dip switches on the printed circuit board (PCB)
to match the receiver. Only use the first 10 switches for the 300MHz system. Then, set the slide switch (SW2) to
either 300MHz or 390MHz as shown below (fig. 1).
5) Plug the 2-lead transmitter wiring harness onto the “COM” & “N.O.” (Normally open) contacts on the door activator’s
microswitch.
6) Attach the box frame to the back plate by placing the “lock lip” of the frame over the top of the back plate and
pushing downward in a hinge-like motion (fig 2).
7) Secure the box frame to its back plate at the underside with a 1/4-20 screw (supplied).
Figure 1
390
SW2
300
CP/TX PCB
S ection 3
Figure 2
BAT T ERY
PCB
LOCK LIP
DOOR ACTIVATOR
SWITCH
FRAME
1/4-20 SCREW
(FRONT VIEW - MOUNTING BOX ONLY)
BACK PLATE
(REAR VIEW)
WARNING: Any changes or modifications not expressly approved by MS Sedco could avoid the user’s authority to operate
this equipment
8701 Castle Park Drive n Indianapolis, Indiana 46256
Telephone: (800) 842-2545/(317) 842-2545 n www.mssedco.com n custsvc@mssedco.com
Page 1
CP/TX

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 1
Create Date                     : 2003:04:15 08:58:29
Modify Date                     : 2003:04:15 08:58:29
Producer                        : Corel PDF Engine Version 9.397
Author                          : J. Kelley Isenhower
Creator                         : CorelDRAW Version 9.397
Title                           : CP-TX Inst.cdr

EXIF Metadata provided by EXIF.tools