MTD 13AF685G700 User Manual LAWN TRACTOR Manuals And Guides 1109238L

User Manual: MTD 13AF685G700 13AF685G700 MTD LAWN TRACTOR - Manuals and Guides View the owners manual for your MTD LAWN TRACTOR #13AF685G700. Home:Lawn & Garden Parts:MTD Parts:MTD LAWN TRACTOR Manual

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

Operator's Manual

_ansmatic Lawn _actor
MODELS
660,680
662,682
663,683
665,685
668,688

IMPORTANT:

Read safety rules and instructions

carefully

before operating

equipment.

Warning:

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brushcovered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required
by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark
arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131
Cleveland, Ohio 44136-9722.

MTB LLC, P.O. BOX361131CLEVELAND,OHIO44136-9722

PRINTED IN U.S.A.

FORM NO. 769-00533C,
(3/31/2004)

TABLEOFCONTENTS
Content

Page
2
3

Customer Support
Important Safe Operation Practices
Tractor Set-up
Controls
Operation

Content
Maintenance
Service

Page
20
22

8
11

Off-season Storage
Attachments & Accessories

Warranty

27
28
Back Cover

FINDINGMODELNUMBER
This Operator's Manual is an important part of your new lawn tractor. It will help you assemble, prepare and
maintain the unit for best performance. Please read and understand what it says.
Before you start assembling your new equipment, please locate the model plate on the equipment
and copy the information from it in the space provided below. A sample model plate is also given below.
You can locate the model plate by looking at the underside of the seat. This information will be necessary
to use the manufacturer's web site and/or help from the Customer Support Department or an authorized
service dealer.

Copy the model number here:

o.o,,o
P. O. BOX

CLEVELAND,OH
330-220-4883

www, mtdproducts.corn

361131

Copy the serial number here:

44136

800-800-7310

CUSTOMER
SUPPORT
Please do NOTreturn the unRto theretailer wRhoutfirst contactingCustomerSupport.
If you have difficulty assembling this product or have any questions regarding the controls, operation or
maintenance of this unit, you can seek help from the experts. Choose from the options below:
Visit mtdproducts.com
for many useful suggestions. Click on Customer Support button and
you will get the four options reproduced here. Click on the appropriate button and help is
immediately available.
_nd

_nswey

Answers

ETye

looking £)r cou!d be just
a mouse crick aw_y/

7_
1__9{1_ te _lleck
medif

7 yo!ll

1_l_estatl_

h<_qllilies,

ef yelll

Illestiel

el II1_1 I've ye_H

pe_sel_al

e Locato_

[< eal as islall_e _ Clik

a_llbe_iz÷

Manuals
Iit÷la_!ll_

you

a mouse click aw_y/

I leHle.

N÷el

{3nswer

f selvi_:÷

celltels

[ieNe t_ fil_l
ill yell_

a_ea,

Online
f_e4_ lecel#

mo(le[

yeals,

If you prefer to reach a Customer Support Representative, please call (330) 220-4MTD or
1(800) 800-7310.

Ma
En

ual
ine

are

/ooking £,r cou/d be just

The engine manufacturer is responsible for all engine-related issues with regard to
performance, power-rating, specifications, warranty and service. Please refer to the engine
manufacturer's Owner's/Operator's Manual, packed separately with your unit, for more
information.

SECTION1: IMPORTANT
SAFEOPERATION
PRACTICES
WARNING:

This symbol points out important safety instructions which, if not followed, could endanger
the personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol--heed its warning.

DANGER:

This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in
serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to
observe the following safety instructions could result in serious injury or death.

or
emit chemicals
to the
Stateof of
cancervehicle
and birth
defects
WARNING:
Engineknown
exhaust,
some
its California
constituents,to cause
and certain
components
reproductive harm.

GENERAL
1.

4.
5.

OPERATION

Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe
place for future and regular reference and for
ordering replacement parts.
Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
Never allow children under 14 years old to operate
this machine. Children 14 years old and over
should read and understand the operation
instructions and safety rules in this manual and
should be trained and supervised by a parent.
Never allow adults to operate this machine without
proper instruction.
To help avoid blade contact or a thrown object
injury, keep bystanders, helpers, children and pets
at least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area.
Thoroughly inspect the area where the equipment
is to be used. Remove all stones, sticks, wire,
bones, toys, and other foreign objects which could
be picked up and thrown by the blade(s). Thrown
objects can cause serious personal injury.
Plan your mowing pattern to avoid discharge of
material toward roads, sidewalks, bystanders and
the like. Also, avoid discharging material against a
wall or obstruction which may cause discharged
material to ricochet back toward the operator.
Always wear safety glasses or safety goggles
during operation and while performing an
adjustment or repair to protect your eyes. Thrown
objects which ricochet can cause serious injury to
the eyes.
Wear sturdy, rough-soled work shoes and closefitting slacks and shirts. Loose fitting clothes and
jewelry can be caught in movable parts. Never
operate this machine in bare feet or sandals.

or
other
contain

10. Be aware of the mower and attachment discharge
direction and do not point it at anyone. Do not
operate the mower without the discharge cover or
entire grass catcher in its proper place.
11. Do not put hands or feet near rotating parts or
under the cutting deck. Contact with the blade(s)
can amputate hands and feet.
12. A missing or damaged discharge cover can cause
blade contact or thrown object injuries.
13. Stop the blade(s) when crossing gravel drives,
walks, or roads and while not cutting grass.
14. Watch for traffic when operating near or crossing
roadways. This machine is not intended for use on
any public roadway.
15. Do not operate the machine while under the
influence of alcohol or drugs.
16. Mow only in daylight or good artificial light.
17. Never carry passengers.
18. Disengage blade(s) before shifting into reverse.
Back up slowly. Always look down and behind
before and while backing to avoid a back-over
accident.
19. Slow down before turning. Operate the machine
smoothly. Avoid erratic operation and excessive
speed.
20. Disengage blade(s), set parking brake, stop engine
and wait until the blade(s) come to a complete stop
before removing grass catcher, emptying grass,
unclogging chute, removing any grass or debris, or
making any adjustments.
21. Never leave a running machine unattended.
Always turn off blade(s), place transmission in
neutral, set parking brake, stop engine and remove
key before dismounting.
22. Use extra care when loading or unloading the
machine into a trailer or truck. This unit should not
be driven up or down ramp(s), because the unit
could tip over, causing serious personal injury. The
unit must be pushed manually on ramp(s) to load or
unload properly.

23. Mufflerandenginebecomehotandcancausea
burn.Donottouch.
24. Checkoverhead
clearances
carefullybeforedriving
underlowhangingtreebranches,wires,door
openingsetc.,wheretheoperatormaybestruckor
pulledfromtheunit,whichcouldresultinserious
injury.
25. Disengage
allattachment
clutches,depressthe
brakepedalcompletely
andshiftintoneutralbefore
attempting
to startengine.
26. Yourmachineisdesigned
tocutnormalresidential
grassofa heightnomorethan10".Donotattempt
to mowthroughunusually
tall,drygrass(e.g.,
pasture)orpilesofdryleaves.Drygrassor leaves
maycontacttheengineexhaustand/orbuildupon
themowerdeckpresenting
a potential
fire hazard.
27. Useonlyaccessories
andattachments
approved
forthismachinebythemachinemanufacturer.
Read,understand
andfollowallinstructions
provided
withtheapproved
accessory
or
attachment.
28. Dataindicates
thatoperators,
age60yearsand
above,areinvolvedina largepercentage
ofriding
mower-related
injuries.Theseoperatorsshould
evaluate
theirabilitytooperatetheridingmower
safelyenoughtoprotectthemselves
andothers
fromseriousinjury.
29. If situations
occurwhicharenotcoveredinthis
manual,usecareandgoodjudgment.Contactyour
customer
servicerepresentative
forassistance.

DO NOT:
1.
2.

3.
4.
5.
6.

SLOPE OPERATION
Slopes are a major factor related to loss of control and
tip-over accidents which can result in severe injury or
death. All slopes require extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not mow
it.
For your safety, use the slope gauge included as part of
this manual to measure slopes before operating this
unit on a sloped or hilly area. If the slope is greater than
15 degrees as shown on the slope gauge, do not
operate this unit on that area or serious injury could
result.

DO:
,

Mow up and down slopes, not across. Exercise
extreme caution when changing direction on
slopes.
Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.

Use slow speed. Choose a low enough speed
setting so that you will not have to stop or shift while
on the slope. Tires may lose traction on slopes
even though the brakes are functioning properly.
Always keep machine in gear when going down
slopes to take advantage of engine braking action.
Follow the manufacturer's recommendations for
wheel weights or counterweights to improve
stability.
Use extra care with grass catchers or other
attachments. These can change the stability of the
machine.
Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction.
Rapid engagement or braking could cause the front
of the machine to lift and rapidly flip over backwards
which could cause serious injury.
Avoid starting or stopping on a slope. If tires lose
traction, disengage the blade(s) and proceed
slowly straight down the slope.

Do not turn on slopes unless necessary; then, turn
slowly and gradually downhill, if possible.
Do not mow near drop-offs, ditches or
embankments. The mower could suddenly turn
over if a wheel is over the edge of a cliff, ditch, or if
an edge caves in.
Do not try to stabilize the machine by putting your
foot on the ground.
Do not use a grass catcher on steep slopes.
Do not mow on wet grass. Reduced traction could
cause sliding.
Do not shift to neutral and coast downhill. Overspeeding may cause the operator to lose control of
the machine resulting in serious injury or death.
Do not tow heavy pull behind attachments (e.g.
loaded dump cart, lawn roller, etc.) on slopes
greater than 5 degrees. When going down hill, the
extra weight tends to push the tractor and may
cause you to loose control. (e.g. tractor may speed
up, braking and steering ability are reduced,
attachment may jack-knife and cause tractor to
overturn).

CHILDREN
,

Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
They do not understand the dangers. Never
assume that children will remain where you last
saw them.
a.

Keep children out of the mowing area and in
watchful care of a responsible adult other
than the operator.
Be alert and turn machine off if a child enters
the area.

Before and while backing, look behind and
down for small children.

Never carry children, even with the blade(s)
shut off. They may fall off and be seriously
injured or interfere with safe machine
operation.

Use extreme care when approaching blind
corners, doorways, shrubs, trees or other
objects that may block your vision of a child
who may run into the machine.

Disengage the cutting blade(s) before
shifting in reverse. The "No-Cut-In Reverse"
feature is a reminder not to cut in reverse and

e.
f.
g.

Never remove gas cap or add fuel while the
engine is hot or running. Allow engine to cool
at least two minutes before refueling.
h. Never over fill fuel tank. Fill tankto no more
than _/2inch below bottom of filler neck to
allow space for fuel expansion.
i.
Replace gasoline cap and tighten securely.
j.
If gasoline is spilled, wipe it off the engine
and equipment. Move unit to another area.
Wait 5 minutes before starting the engine.
k. To reduce fire hazards, keep machine free of
grass, leaves, or other debris build-up. Clean
up oil or fuel spillage and remove any fuel
soaked debris.
I. Never store the machine or fuel container
inside where there is an open flame, spark or
pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas
appliances.
m. Allow a machine to cool at least five minutes

to help avoid back over accidents. Do not
defeat it.

Keep children away from hot or running
engines. They can suffer burns from a hot
muffler.

Remove key when machine is unattended to
prevent unauthorized operation.

Never allow children under 14 years old to operate
the machine. Children 14 years old and over should
read and understand the operation instructions and
safety rules in this manual and should be trained
and supervised by a parent.

TOWING
1.

Tow only with a machine that has a hitch designed
for towing. Do not attach towed equipment except
at the hitch point.
Follow the manufacturers recommendation for
weight limits for towed equipment and towing on
slopes.
Never allow children or others in or on towed
equipment.

On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.

5.
6.

Travel slowly and allow extra distance to stop.
Do not shift to neutral and coast downhill.

before storing.
GENERAL SERVICE:
1.

SERVICE
SAFE HANDLING OF GASOLINE:
,

To avoid personal injury or property damage
use extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
a.
b.

Use only an approved gasoline container.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.

When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times
until fueling is complete. Do not use a nozzle
lock-open device.
Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
Neverfuel machine indoors.

Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless, and deadly gas.
Before cleaning, repairing, or inspecting, make
certain the blade(s) and all moving parts have
stopped. Disconnect the spark plug wire and
ground against the engine to prevent unintended
starting.
Periodically check to make sure the blades come to
complete stop within approximately (5) five
seconds after operating the blade disengagement
control. If the blades do not stop within the this time
frame, your unit should be serviced professionally
by an authorized MTD Service Dealer.
Check brake operation frequently as it is subjected
to wear during normal operation. Adjust and service
as required.
Check the blade(s) and engine mounting bolts at
frequent intervals for proper tightness. Also,
visually inspect blade(s) for damage (e.g.,
excessive wear, bent, cracked).

Replace
theblade(s)withtheoriginalequipment
manufacturer's
(O.E.M.)blade(s)only,listedinthis
manual."Useofpartswhichdonotmeetthe
originalequipment
specifications
mayleadto
improperperformance
andcompromise
safety!"
6. Mowerbladesaresharp.Wrapthebladeorwear
gloves,anduseextracautionwhenservicing
them.
7. Keepallnuts,bolts,andscrewstighttobesurethe
equipment
is insafeworkingcondition.
8. Nevertamperwiththesafetyinterlocksystemor
othersafetydevices.Checktheirproperoperation
regularly.
9. Afterstrikinga foreignobject,stoptheengine,
disconnect
thesparkplugwire(s)andground
againsttheengine.Thoroughly
inspectthe
machine
foranydamage.Repairthedamage
beforestartingandoperating.
10. Neverattemptto makeadjustments
or repairsto
themachinewhiletheengineis running.
_

11.Grasscatchercomponents
andthedischarge
coveraresubjecttowearanddamagewhichcould
exposemovingpartsorallowobjectstobethrown.
Forsafetyprotection,
frequently
checkcomponents
andreplaceimmediately
withoriginalequipment
manufacturer's
(O.E.M.)partsonly,listedinthis
manual."Useofpartswhichdonotmeetthe
originalequipment
specifications
mayleadto
improper
performance
andcompromise
safety!"
12. Donotchangetheenginegovernor
settingsor
over-speed
theengine.Thegovernor
controlsthe
maximum
safeoperating
speedoftheengine.
13. Maintain
or replacesafetyandinstruction
labels,as
necessary.
14.Observeproperdisposallawsandregulations
for
gas,oil,etc.toprotecttheenvironment.

read,
understand
and RESPONSIBILITYfollow the warningsRestrict
and instructions
this power
manualmachine
and on the
machine. who
ARNING:
YOUR
the use ofinthis
to persons

TO AVOID SERIOUS
iNJURY OR DEATH
* O0 UP AHDDOWNSLOPES_
NOTACROSS.
* AVOIDSUDDENTURNS.
* ]DONOTOPERATE
THE UNITWHEREiT
COULDSLIPORTiP.
* iF MACHINESTOPSGOINGUPHiLL_
STOP
BLADE(S)ANDBACHDOWNHILLSLOWLY.
* ]DONOTMOWWHENCHILDREN
OROTHERSAREADOUHD.
* NEVERCARRYCHILDRENEVENWiTH
BLADESOFF.
* LOOHDOWH& BEHINDBEFOREAND
WHILEBACHmG.
*HEEP SAFETYDEVICES(GUARDS,
SHIELDS,ANDSWITCHES,ETC.)
iN PLACEADDWORKING.
* REMOVEOBJECTS
THATCOULD
RE THROWNBY THEBLADE(S).
* HNOWLOCATION
ANDFUNCTIONOF ALL
CONTROLS.
* BE SUREBLADE(S)AHDENOIHEARE
STOPPEDBEFORE
PLACINGHANDS
0R FEETNEARBLADE(S).
* BEFORELEAVINGOPERATOR'S
POSiTiON,
DISENOADE
BLADE(S),
PLACETHECONTROL
LEVERiN NEUTRAL,ENGADEPADKING
RRAHE_SHUTOFFANDREMOVEHEY.

READ OPERATOR'S

A CORNER OF A BUILDING
OR A FENCE POST

W
15 °

w
Q.

_WARNING

Z
I-W

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower
could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain
your footing and you could slip, resulting in serious injury.
Operate RIDING mowers up and down slopes, never across the face of slopes.

SECTION3: TRACTOR
SET-UP
IMPORTANT:Your tractor is shipped with motor oil in the engine. However, you MUST check the oil level before
starting the engine and operating. Refer to the separate Briggs & Stratton Operator/Owner Manual (or Tecumseh
eng ne s Owner s Manua ) packed w th your tractor. Read nstruct ons carefu y.

NOTE:

Reference to right or left hand side of the un#
is observed from the driver's seat, facing forward.

AttachingTheSteeringWheel
The hardware for attaching the steering wheel has
been packed within the steering wheel, beneath
steering wheel cap. Carefully pry off the steering
wheel cap and remove the hardware.

Tools RequiredFor Set-up
(1) 1/2" socket wrench (for steering wheel)
(1) 9/16" wrench or socket wrench (for models with
standard adjustment seat only)
(2) 7/16" wrenches or socket wrenches (for battery)

ShippingBraceRemoval
engine
is off, remove
key, mower's
and set
WARNING:
Make the
sure ignition
the riding
the parking brake before removing the
shipping brace.
•

Locate the shipping brace and warning tag found
on the right side of the mower, between the
discharge chute and the cutting deck. See Figure 1

NOTE:

There are two different styles of steering
wheel cap. See Figure 2. Styles vary by modeL

•

Remove the steering bellow from its packaged
location on the PTO (blade engage) lever (found on
the right hand side of tractor). NOTE: Tractor
models 668 & 688 do NO T require a steering bellow
and do NOT come equipped with one.

•

On models so equipped, place the steering bellow
over the steering shaft extending through the dash.
See Figure 2.

NOTE:

If the openings on each end of the steering
bellow are two different sizes, the smaller end goes
down, against the dash of the lawn tractor.
With the wheels of the tractor pointing straight
forward, place the steering wheel over the steering
shaft.
Place the washer (with the cupped side down) over
the steering shaft and secure with the hex bolt. See
Figure 2.
Place the steering wheel cap over the center of the
steering wheel and push downward until it "clicks"
into place.
Steering
Figure 1
While holding the discharge chute with your left
hand, remove the shipping brace with your right
hand by grasping it between your thumb and index
finger and rotating it clockwise.

Wheel Cap 1

__'
_
Hex Bolt

_=_

& Washer

St;hrif_g
_,

shipping
purposes
must be
removed
ARNING:
Theonly,
shipping
brace,
used and
for
discarded before operating your riding mower.

St;e;iring

WARNING:

The mowing deck is capable of
throwing objects. Failure to operate the riding
mower without the discharge cover in the
proper operating position could result in
serious
personal
injury and/or property
damage.

Figure 2

AttachingTheSeat
Seat styles vary by tractor model and there are three
different styles available:
•
Standard Adjustment
•
Quick Adjustment &
•
Knob Adjustment
Refer to Figure 3, Figure 4 and Figure 5 to identify your
tractor's seat style and follow applicable instructions
below.

NOTE:

For shipping reasons, seats are either
fastened to the tractor seat's pivot bracket with a plastic
tie, or mounted backward to the pivot bracket. In either
case, free the seat form its shipping position and
remove the two hex screws (or knobs, on models so
equipped) from the bottom of seat before proceeding
with applicable instructions below.
Standard AdjustmentSeat
1. Position the shoulder screws (found on the base of
the seat) inside the slot openings in the seat pivot
bracket. Figure 3.
2. Slide the seat slightly rearward in the seat pivot
bracket, lining up the rear slots in the pivot bracket
with the remaining two holes in the seat's base.
3. Select desired position for the seat, and secure with
the two hex screws removed earlier. See Figure 3.

Standard Adjustment
Hex Screws

Shoulder
Screws

Opening
in Slot

Pivot Bracket

Figure 3
QuickAdjustment

Seat Stop

QuickAdjustmentSeat

NOTE:

If your seat was shipped mounted backwards
on the seat pivot bracket, pull out the tab found on the
seat stop and hold # open while sliding the seat off the
seat pivot bracket. See Figure 4.
1.
2.

Tab-Pivot Bracket

Line up the plastic seat spacers with the slots in
seat pivot bracket.
Slide seat in until front seat spacer engages the
seat stop. See Figure 4.
WARNING:
Before operating this machine,
make sure the seat is engaged in the seat
stop, stand behind the machine and pull back
on seat until fully engaged into stop.

Figure 4
KnobAdjustment

Knobs

KnobAdjustmentSeat
1.

Position the shoulder screws (found on the base of
the seat) inside the slot openings in the seat pivot
bracket. Figure 5.
Slide the seat slightly rearward in the seat pivot
bracket, lining up the rear slots in the pivot bracket
with the remaining two holes in the seat's base.
Select desired position for the seat, and secure with
the two knobs removed earlier. See Figure 5.

Shoulder
Screws

Opening
in Slot_

Figure 5

GasandOilFill-up
Rubber
Boot

The gasoline tank is located under the hood and has a
capacity of 1-1/2 gallons. Do not overfill.

WARNING:

Use

extreme

care

when

handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine
is hot or running.
Extinguish
cigarettes, cigars, pipes, and other sources of
ignition.
Service the engine with gasoline and oil as instructed in
the separate Briggs & Stratton Operator/Owner Manual
(or Tecumseh engine's Owner's Manual) packed with
your tractor. Read instructions carefully.
IMPORTANT: Your tractor is shipped with motor oil in the
engine. However, you MUST check the oil level before
operating. Be careful not to overfill.

Hex Bolt

Figure 6
IMPORTANT:If the battery is put into service after the
date shown on top of battery, charge the battery as
instructed on page 24 of this manual prior to operating
the tractor.

Tire Pressure
any
circumstances
is 30
Equalunder
tire
WARNING:
Maximum
tire psi.
pressure
pressure should be maintained at all times.

Identifyingthe Mulch Plug (if soequipped)
On tractor models with 38- and 42-inch decks so

The tires on your unit may be over-inflated for shipping
purposes. Reduce the tire pressure before operating
the tractor. Recommended operating tire pressure is
approximately 10 p.s.i for the rear tires & 14 p.s.i, for
the front tires. Check sidewall of tire for maximum p.s.i.

equipped, a mulch plug can be found within the cutting
deck's discharge opening.
NOTE: Refer to Mulchingon page 15 for more detailed
information.

Attachingthe BatteryCables

If you'd prefer to operate the cutting deck without
mulching, simply remove the mulch plug by
unthreading the plastic wing nut which fastens it to the
cutting deck. This will allow the grass clippings to
discharge out of the discharge opening during
operation. See Figure 7.

NOTE:

Some models are shipped with the battery
cables already connected.

NOTE:

The positive battery terminal is marked Pos.
(+). The negative battery terminal is marked Neg. (-).

•

The positive cable (heavy red wire) is secured to
the positive battery terminal (+) with a hex bolt and
hex nut at the factory. Make certain that the rubber
boot covers the terminal to help protect it from
corrosion.

•

Remove the hex bolt and hex nut from the negative
cable.

•

Remove the black plastic cover, if present, from the
negative battery terminal and attach the negative
cable (heavy black wire) to the negative battery
terminal (-) with the bolt and hex nut.
Make certain the hold-down rod is in position over
the battery, securing it in place. See Figure 6.

•

Figure 7

Mulch Plug

SECTION4: CONTROLS

A
E

B
C

I-II-II-II-II-ID
1-11-11-11-1
I-I1-11-113
1-11-11-11-11-11-1
t If so equipped

NNNmm_

NOTE:

Steering Wheel not shown for clarity,

Figure 8
A

Clutch-brake Pedal

B
C

Choke Controlt
Throttle Control Lever

Pto (Blade engage) Lever

E
F

Ignition Switch
Shift Lever

Speed Control Lever/Parking

Seat Adjustment Levert

Brake

IgnitionSwitch
STOP

The ignition switch is located on the right side of the
tractor's dash.To start the engine, insert the key into the
ignition switch and turn clockwise to the START
position. Release the key into the ON position once
engine has fired. See Figure 9.
Refer to StartingTheEngineon page 13 of this manual for
detailed starting instructions

Tractor Models

START

668 & 688 Only

WARNING:

Never
leave a running
machine unattended. Always move the PTO
(blade engage) lever into the disengaged
(BLADES STOP) position, Shift into neutral,
set parking brake, stop engine and remove
key to prevent unintended starting.

All Tractor Models
Except 668 & 688

Figure 9
11

ChokeControl
On some models, moving the
throttle lever all the way forward
activates the engine's choke
control. On all other models, the
choke control can be found on

To release the parking brake, depress the clutch-brake
pedal and move the speed control lever out of the
notches to the desired position. Release the speed
control lever and the clutch-brake pedal.

_._

NOTE:

The parking brake must be set if the operator
leaves the seat with the engine running or the engine
will automatically shut off.

the left side of the dash panel and is activated by pulling
the knob outward. Activating the choke control closes
the choke plate on the carburetor and aids in starting
the engine. Refer to Starting TheEngineon page 13 of this
manual for detailed starting instructions.

ThrottleControlLever
The throttle control lever is
located on the left side of the
tractor's dash panel. This lever
controls the speed of the engine
and, on some models, when
pushed all the way forward, the
choke control also. When set in a

Choke
Position

IMPORTANT:Always set the parking brake when
leaving the tractor unattended.

ShiftLever
The shift lever is
located in the center of
the console and has

I_tbl

three positions, F
(Forward), N (Neutral)
and R (Reverse). See
Figure 8. The clutchbrake pedal must be
fully depressed and the
tractor must not be in

Fast
Position

given position, the throttle will
maintain a uniform engine speed.
IMPORTANT:When operating the
tractor with the cutting deck
engaged, be certain that the
throttle lever is always in the
FAST (rabbit) position.

R
Shift
Knob

motion when the moving shift lever.
IMPORTANT:Never force the shift lever. Doing so may
result in serious damage to the tractor's transmission.
Slow
Position

NOTE: If difficulty is encountered while attempting to
(_

shift, release the clutch-brake pedal slightly before fully
depressing the pedal again.

SpeedControlLever
Clutch-brakePedal

The speed control lever,
located on the right side of
m
m5
the center console, allows
m
m
you to regulate the ground
m,,4
m
speed of the lawn tractor.
To use, depress the clutchbrake pedal and move the
J
lever out of the parking
brake notch and forward to
increase the tractor's
ground speed. When a
desired speed has been
J
reached, release the lever
into an appropriate notch to
maintain that speed.
To slow the tractor's
6-Speed Model Shown
ground speed, depress the
clutch-brake pedal and move the speed control lever
rearward and release it into a notch.

The clutch-brake pedal is located on the left side of the
lawn tractor, along the running board. Depress the
clutch-brake pedal part way down when slowing the
tractor by changing speeds (Refer to SpeedControlLever).
Depress the pedal all the way down to engage the disc
brake and bring the tractor to a complete stop.

NOTE:

The pedal must be depressed to start the
engine. Refer to SafetyInterlockSwitcheson page 13.

Pt0 (Bladeengage)Lever
Found on the right side of the tractor, the PTO (blade
engage) lever is used to set the mowing deck's cutting
height and engage the power to the cutting deck or
other (separately available) attachments. To operate,
move the lever to the right and forward, before placing
in a notch for your desired cutting height. Moving the
lever to the right and all the way rearward placing it into
the BLADES STOP position disengages power to the
cutting deck/attachment.

Parking Brake
To set the parking brake, fully depress the clutch-brake
pedal. Move the speed control lever all the way to the
rear and release it into the parking brake position.
Release the clutch-brake pedal to allow the parking
brake to engage.

NOTE: The PTO (blade engage) lever must be in the
disengaged (BLADES STOP) position when starting
the engine, when traveling in reverse and if the operator
leaves the seat.
12

SECTION5: OPERATION
StartingtheEngine

WARNING
AVOIDSERIOUSINJURYORDEATH
• GO UP AND DOWN SLOPES, NOT ACROSS.
• AVOID SUDDEN TURNS.
• DO NOT OPERATE THE UNIT WHERE IT COULD
TIR

interlock system
is operate
malfunctioning.
WARNING:
Do not
the tractor ifThis
the
system was designed for your safety and
protection.

SLIP OR

• IF MACHINE STOPS GOING UPHILL, STOP BLADE(S)
BACK DOWNHILL SLOWLY.
• DO NOT MOW WHEN
CHILDREN
OR OTHERS
AROUND.

NOTE:

Refer to the TRACTOR
SET-UPon page 8 of this
manual for Gasoline and Oil fill-up instructions.

AND
ARE

•
•

• NEVER CARRY CHILDREN, EVEN WITH BLADES OFE
• LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.

•
•
•

• KEEP
SAFETY
DEVICES
(GUARDS,
SHIELDS,
AND
SWITCHES) IN PLACE AND WORKING.
• REMOVE OBJECTS THAT COULD BE THROWN BY THE
BLADE(S).
• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.
• BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE
PLACING HANDS OR FEET NEAR BLADE(S).
• BEFORE LEAVING OPERATOR'S
POSITION,
DISENGAGE

IMPORTANT: Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing so
may cause damage to your engine's electric starter.

BLADE(S), PLACE THE SHIFT LEVER IN NEUTRAL, ENGAGE
PARKING BRAKE, SHUT ENGINE OFF AND REMOVE KEY.

•

READOPERATOR'S
MANUAL

operating the tractor. Doing so will result in a "rich" fuel
mixture and cause the engine to run poorly.

NOTE:

all
instructions and
warnings
on theand
machine
WARNING:
Read,
understand,
follow
and in this manual before operating.

If Starting problems are encountered, refer to
TROUBLE
SNOOTING
GUIDEon page 29.

This tractor is equipped with a safety interlock system
for the protection of the operator. If the interlock system
should ever malfunction, do not operate the tractor.
Contact an authorized MTD service dealer. The safety
interlock system prevents the engine from cranking or
starting unless the parking brake is engaged, and the
PTO (blade engage) lever is in the disengaged
(BLADES STOP) position.
•
•

•

After the engine starts, deactivate the choke control
and place the throttle control in the FAST position.

IMPORTANT: Do NOT leave the choke control on while

SafetyInterlockSystem
,_

Insert the tractor key into the ignition switch.
Place the PTO (blade engage) lever in the BLADES
STOP position.
Engage the tractor's parking brake.
Activate the choke control.
Turn the ignition key clockwise to the START
position. After the engine starts, release the key. It
will return to the ON position.

StoppingtheEngine
stop the engine,If you
disconnect
sparkobject,
plug
WARNING:
strike a the
foreign
wire(s) and ground against the engine.
Thoroughly
inspect the machine for any
damage. Repair the damage before restarting
and operating

The engine will automatically shut off if the operator
leaves the seat before engaging the parking brake.
The engine will automatically shut off if the operator
leaves the tractor's seat with the PTO (blade
engage) lever in ANY position other than BLADES
STOP.

•
•
•

The engine will automatically shut off if the PTO
(blade engage) lever is moved out of the BLADES
STOP position with the shift lever in R (reverse).

•
•

BeforeStartingEngine
all
instructions and
warnings
on theand
machine
WARNING:
Read,
understand,
follow
and in this manual before operating.

If the blades are engaged, place the PTO (blade
engage) lever in the BLADES STOP position.
Depress the clutch-brake pedal to bring the tractor
to a complete stop.
Turn the ignition key counterclockwise to the OFF
position.
Engage the tractor's parking brake.
Remove the key from the ignition switch to prevent
unintended starting.

Operating
TheLawnTractor

•
•
•
•
•
•

before
and while
backing
to avoid
backWARNING:
Always
lookupdown
and abehind
over accident.

WARNING:

Before leaving the operator's
position. Always place the PTO (blade
engage) lever in the BLADES STOP position,
shift into neutral, set parking brake, stop
engine
and
remove
key to prevent
unintended starting.
•

Restart engine.
Place speed control lever in highest speed position.
Release clutch-brake pedal fully.
Depress clutch-brake pedal.
Place speed control lever in desired position.
Place shift lever in either FORWARD or REVERSE,
and follow normal operating procedures.

Headlights
The lamps, on models so equipped, are ON whenever
the tractor's engine is running. They turn OFF when the
ignition key is moved to the STOP position.

Move throttle control lever to full throttle.

NOTE: Since the engine's alternating system supplies
NOTE:

Always operate the tractor with the throttle
control lever in the FAST (rabbit) position for the most
efficient use of the cutting deck or other (separately
available) attachments.

the electricity to power the lamps, use of the headlights
cannot drain your battery.

EngagingTheCuttingBlades

Place the shift lever in either the FORWARD or
WARNING:
Keep feet and hands away
from the discharge opening, the blades or
any part of the deck. When the unit is used
for anything other than mowing operations,
the blade drive should be disengaged.

REVERSE position.
Release the parking brake by depressing the
clutch-brake pedal and positioning the speed
control lever in desired position.
IMPORTANT: First-time operators should use speed
positions 1 or 2. Become completely familiar with the
tractor's operation and controls before operating the
tractor in higher speed positions.
•
•

To engage power to the cutting deck or other
(separately available) attachment, proceed as follows:
•

Release clutch-brake pedal slowly to put unit into
motion.
The lawn tractor is brought to a stop by depressing
the clutch-brake pedal.

•
•

NOTE:
When operating the unit initially, there will be
little difference between the highest two speeds until
after the belts have seated themselves into the pulleys
during the break-in period.

NOTE: The PTO (blade engage) lever must be in the
disengaged (BLADES STOP) position when starting
the engine, when traveling in reverse and if the operator
leaves the seat. Refer to SafetyInterlock Switches on page
13.

position
for any
reason,
the
WARNING:
Before
leaving disengage
the operator's
blades, place the shift lever in neutral,
engage the parking brake, shut engine off
and remove the key.

Mowing
WARNING:

To help avoid blade contact or
a thrown object injury, keep bystanders,
helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop
machine if anyone enters the area.

IMPORTANT: When stopping the tractor for any reason
while on a grass surface, always
Place the shift lever in neutral,
Engage the parking brake,
Shut engine off and remove the key.

The following information will be helpful when using the
cutting deck with your tractor.

Doing so will minimize the possibility of having your
lawn "browned" by hot exhaust from your tractor's
running engine.

WARNING:

Plan your mowing pattern to
avoid discharge of materials toward roads,
sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or
obstruction which may cause discharged
material to ricochet back toward the operator.

If unit stalls with speed control in high speed, or if unit
will not operate with speed control lever in a low speed
position, proceed as follows.
•

Move the PTO (blade engage) lever to the right and
forward,
Place the lever in a notch for you r desired cutting
height.
Moving the lever to the right and all the way
rearward placing it into the BLADES STOP position
raises and disengages power to the cutting deck.

Place shift lever in NEUTRAL.

•

•
•

•
•
•

•

Be sure that the lawn is clear of stones, sticks, wire,
toys or other objects which could damage lawn
mower or engine.
For best results and to insure more even grass
distribution, do not mow when lawn is excessively
wet.
Do not mow at high ground speed, especially if a
mulch kit or grass collector is installed.
For best results it is recommended that the first two
laps be cut with the discharge thrown towards the
center. After the first two laps, reverse the direction
to throw the discharge to the outside for the
balance of cutting. This will give a better
appearance to the lawn.
Do not cut the grass too short. Short grass invites
weed growth and yellows quickly in dry weather.
Mowing should always be done with the engine at
full throttle.
Under heavier conditions it may be necessary to go
back over the cut area a second time to get a clean
cut.
Do NOT attempt to mow heavy brush and weeds
and extremely tall grass. Your tractor is designed to
mow lawns, NOT clear brush.
Keep the blades sharp and replace the blades
when worn. Refer to CuttingBladeson page 23 of this
manual for proper blade sharpening instructions.

Maintain a slow ground speed to allow the grass
clippings more time to effectively be mulched.
Always position the throttle control lever in the
FAST (rabbit) position and allow it to remain there
while mowing. Failing to keep the engine at full
throttle places strain on the tractor's engine and
does not allow the blades to properly mulch grass.

NOTE:

It is not necessary to remove the discharge
chute to operate the mower with the mulch kit installed.
38- and 42-inch Decks
To operate the cutting deck without mulching, on
models so equipped, simply remove the mulch plug by
unthreading the plastic wing nut which fastens it to the
cutting deck. This will allow the clippings to discharge
out the side. See Figure 10.
Carriage

Mulching
Some, NOT ALL, models come equipped with a mulch
kit which incorporates special blades, already standard
on your tractor, in a process of recirculating grass
clippings repeatedly beneath the cutting deck. The
ultra-fine clippings are then forced back into the lawn
where they act as a natural fertilizer. Observe the
following points for the best results when mulching.
•

•

Plastic Wing Nut

Mulch Plug

Figure 10
46-inch Decks

Never attempt to mulch if the lawn is damp. Wet
grass tends to stick to the underside of the cutting
deck preventing proper mulching of the clippings.
Do NOT attempt to mulch more than 1/3 the total
height of the grass or approximately 1-1/2 inches.
Doing so will cause the clippings to clump up
beneath the deck and not be mulched effectively.

On models so equipped, the mulch kit is packed
separately within the tractor's crate. Observe the
instructions included with the mulch kit for the best
results when mulching.

SECTION6: MAKINGADJUSTMENTS
adjustments
engineto ismake
running,
WARNING: while
Nevertheattempt
any
except where specified in the operator's
manual.

Hex Screws

StandardAdjustmentSeat
To adjust the position of the seat, loosen the two hex
screws on the bottom of the seat. See Figure 11. Slide
the seat forward or backward as desired. Retighten the
two screws.

QuickAdjustmentSeat (if soequipped)
To adjust the position of the seat on models so
equipped, move the seat adjustment lever (located
under the seat) to the left and slide the seat forward or
backwards. See Figure 12. Make sure seat is locked
into one of the six adjustment positions before
operating the lawn tractor.

Figure 11

Seat
Adjustment
Lever

KnobAdjustmentSeat(if soequipped)
To adjust the position of the seat on models so
equipped, loosen the two knobs on the bottom of the
seat. See Figure 13. Slide the seat forward or backward
as desired. Retighten the two knobs.

DeckLevelingAdjustment
WARNING:
heavy
gloves toProtect
grasp the
yourcutting
handsblade.
by wearing
Seat

NOTE:

Check the tractor's tire pressure before
performing any deck leveling adjustments. Refer to
Tires later in this section for further information

regarding tire pressure.

Figure 12

The front of the cutting deck is supported by two lift
links, one of which can be adjusted to level the deck
from both front to rear & side to side. The front of the
deck should be between 1/4-inch and 3/8-inch lower

Knobs

than the rear of the deck. Adjust if necessary as follows:
•

•
•

With the tractor parked on a firm, level surface,
place the PTO (blade engage) lever in the top
cutting height notch (not BLADES STOP) position.
Rotate the blade nearest the discharge chute so
that it is parallel with the tractor.
Measure the distance from the front of the blade tip
to the ground and the rear of the blade tip to the
ground. The first measurement taken should be
between 1/4" and 3/8" less than the second
measurement. Determine the approximate distance
necessary for proper adjustment and proceed, if
necessary, to the next step.

Figure 13
16

Place the PTO (blade engage) lever in the engaged
(second-lowest cutting height) position.
Remove the hairpin clip from the ferrule found at
the bottom of the front, left deck link (hairpin clip is
on the inside of the lift link). See Figure 14.

DeckEngagement
Adjustment
adjustment while
the attempt
engine to is make
running.
WARNING:
Never
the
Always shift to neutral, set the parking brake,
stop engine and remove key to prevent
unintended starting.

The cutting deck engagement may be adjusted to make
certain the deck is disengaged when PTO (blade
engage) lever is in the BLADES STOP position. Correct
adjustment as follows.
•

•

With the engine off, place the PTO (blade engage)
lever in the top cutting height notch (not BLADES
STOP) position.
Unthread the shift knob and remove the two flange
screws which secure the shift cover panel in place.
See Figure 15.
Flange Screws

Adjustable Deck Link,
Ferrule & Hairpin Clip

Figure 14
Pull the ferrule out of the deck hanger and thread
the ferrule up or down, as necessary.

NOTE: Usually only one or two turns are needed.
•
•

•

Insert the ferrule back into the deck hanger and
refasten with the hairpin clip removed earlier.
Check the front-to-rear adjustment by remeasuring. Check the side-to-side adjustment by
placing a level on the deck surface.
Readjust if necessary.

Shift Knob

/
Shift Cover Panel

Settingthe DeckWheel Height (on modelsso equipped)
•

•

Select the height position of the cutting deck by
placing the PTO (blade engage) lever in any of the
five different cutting height notches on the right side
of the frame.

Figure 15
Remove the shift cover panel and locate the deck
disengagement rod. See Figure 16.

Adjust the deck wheels so that they are between 1__
inch and Y2-inch above the ground when the tractor
is on a smooth, flat surface such as a driveway.
Assembly
/_1 Stabilizer
/
Shaft

from
the discharge
of the
ARNING:
Keep opening
hands and
feet cutting
away
deck.

NOTE:
The deck wheels, on models so equipped, are
an anti-scalp feature of the deck and are not designed
to support the weight of the cutting deck.

Refer to DeckLevelingAdjustment
on page 16 of this
manual for more detailed instructions regarding deck
adjustments.

Disengagement

Rod

Figure 16
17

NOTE:

There is a small yellow wire connected to a
spring switch on the underside of the shift cover panel
Be careful not to damage it when removing the panel

Spring
Hex Compression
Nut

Remove the hairpin clip which secures the
disengagement rod to the stabilizer shaft assembly.
Pull the rod toward the rear of the tractor (to take up
slack), then thread the rod inward or outward
(usually only one ortwo turns) until the rod lines up
as precisely as possible with the hole in the
stabilizer shaft.

NOTE:

Threading the disengagement rod outward
(toward the rear of the tractor) provides for more belt
tension. Threading the disengagement
rod inward
provides for less belt tension.
•

Disc

Transmission

Reinsert the rod in the stabilizer shaft and re-

NOTE:

secure it with the cotter pin removed earlier.
Check the adjustment by placing the PTO (blade
engage) lever in the BLADES STOP position. The deck
should move up and forward, allowing the belt to
become loose.
•
•

•

Figure 17

SpeedControlAdjustment
NOTE:

Reassemble the shift cover panel.
Start the tractor's engine and test the PTO (blade
engage) lever to be certain the blades fully
disengage when in the BLADES STOP.
Repeat the adjustment procedure if necessary.

When operating the un# initially or after
replacing the belts, there will be little difference
between the highest two speeds until after the belts
have gone through a break-in period and have seated
themselves into the pulleys,
If the full range of speeds cannot be obtained on your
unit, adjust the speed control as follows.

ParkingBrakeAdjustment

•

WARNING:

Never attempt to adjust the
brakes while the engine is running. Always
place the PTO (blade engage) lever in the
BLADES STOP position, shift into neutral, set
parking brake and remove the key to prevent
unintended starting.

•

•
•
•

Unthread the shift knob and remove the two flange
screws which secure the shift cover panel in place.
Refer to Figure 15.
Remove the shift cover panel and locate the speed
control rod. See Figure 18.

NOTE:

There is a small yellow wire connected to a
spring switch on the underside of the shift cover panel
Be careful not to damage it when removing the panel.

If the tractor does not come to a complete stop when
the clutch-brake pedal is completely depressed, or if
the tractor's rear wheels can roll with the parking brake
applied, the brake is in need of adjustment. The brake
disc can be found on the right side of the transmission
in the rear of the tractor. Adjust if necessary as follows:
•

Rear, right wheel not shown for clarity

Ferrule and
Hairpin Clip

Looking at the transmission from the right side of
the tractor, locate the compression spring and
brake disc. See Figure 17.
Loosen, but do NOT remove, the hex nut found on
the right side of the brake assembly. See Figure 17.
Using a feeler gauge, set the gap between the
brake disc and the brake puck at .011"
Re-tighten the hex nut loosened earlier.

Speed Control Rod

Figure 18
18

•

Remove the hairpin clip which secures the speed
control rod's ferrule to the speed bracket. See
Figure 18.
At the factory, the speed control rod is adjusted so that
5/8-in. of the rod is exposed beyond the ferrule.
•

•
•

Adjust the speed control by threading the ferrule
inward so that no more than 3/4-in. of the rod is
exposed beyond the ferrule. See Figure 19.
Reinsert the ferrule and re-secure the rod with the
cotter pin removed earlier.
Reassemble the shift cover panel, start the tractor's
engine and test the full range of speeds.

IMPORTANT: If the above adjustment did not result in
the tractor obtaining the full range of speeds, see an
authorized MTD service dealer to have the variable
speed drive system inspected and professionally
adjusted.

NOTE:

Figure is NOT to scale

Figure 19

SteeringAdjustments
Brag Link Adjustment(All Tractors Model)
If the tractor turns tighter in one direction than the other,
or if either the drag link and ball joint are being replaced
due to damage or wear, the drag link may need to be
adjusted. To do so, proceed as follows:
•

Place the steering wheel in position for straightahead travel.

•

Remove the lock nut which secures the ball joint to
the steering arm. See Figure 20.
Lift the ball joint out of the steering arm and reposition both front tires for straight-ahead travel.
Loosen the jam nut (See Figure 20) and thread the
ball joint either inward or outward until it aligns with
the hole in the steering arm.
Confirm that both the steering wheel and the front
tires are still positioned for straight-ahead travel
before reinserting the ball joint into the steering arm
and securing it with the lock nut removed earlier.
Re-tighten the jam nut loosened earlier.

•
•

•

Drag Link

Steering Arm
Lock Nut

Figure

Tie RodAdjustment(Models With AdjustableTie Rod)
If the tractor appears to be difficult to drive in a straightahead direction, or if either the tie rod or tie rod ferrule
are being replaced due to damage or wear, the tie rod
may need to be adjusted to correct the tractor's "toe-in."
To do so, proceed as follows:

Flat Washe
/Cotter Pin

NOTE:

A replacement cotter pin (part no. 714-0470)
is needed to complete this adjustment. Have one on
hand before proceeding.
•
•

Perform the DragLink Adjustment.
See page 19.
Place the steering wheel in position for straightahead travel.

•

In front of the pivot bar, measure the distance
horizontally from the inside of the left rim to the
inside of the right rim. Note the distance.

Ferrule _

Tie Rod
Right Axle

Right Front Tire

Figure 21
19

•

Behind the pivot bar, measure the distance
horizontally from the inside of the left rim to the
inside of the right rim. Note the distance.
The measurement taken in front of the pivot bar
should be between 1/16" and 5/16" less than the
measurement taken behind the pivot bar. If it is not,
an adjustment is necessary. Proceed as follows.
Locate the ferrule at the right end of the tie rod, just
to the rear of the right, front tire of tractor. See
Figure 21.
Remove the cotter pin and flat washer which
secures the adjustment ferrule to the tractors right
axle.
Two turns at a time, thread the adjustment ferrule
toward the right, front tire to lengthen the tie rod. Or,
thread the adjustment ferrule away from the right,
front tire to shorten the tie rod.

NOTE:

Lengthening the tie rod increases the tractor's
front tie toe-in. Shortening the tie rod decreases the
tractor's front tire toe-in.
Reinsert the adjustment ferrule and temporarily
secure it with the cotter pin removed earlier.
Make certain the steering wheel is in position for
straight-ahead travel before again taking
measurements. Continue to repeat the steps above
until a proper adjustment is achieved.
Secure the tie rod to the right axle with the flat
washer removed earlier and a replacement cotter
pin.
IMPORTANT: Do NOT reuse the original cotter pin once
it has been removed.

SECTION7: MAINTAINENCE
WARNING:
Before
performing
any
maintenance or repairs, place the PTO (blade
engage) lever in the BLADES STOP position,
move shift lever into neutral position, set
parking brake, stop engine and remove key to
prevent unintended starting.

Changing Engine Oil
(modelsequippedwith an 0il drain sleeve)
For draining oil from the engine's crankcase of select
model tractors, a plastic oil drain sleeve is packed with
this Operator's Manual. To drain the oil, proceed as
follows:
•

Cleaningthe EngineAndDeck

•

Any fuel or oil spilled on the machine should be wiped
off promptly. Do NOT allow debris to accumulate
around the cooling fins of the engine or on any other
part of the machine, especially the belts, pulleys and
other moving parts. Clean the underside of the deck
with a wisk broom, scraper or forced air after each
mowing.

Unscrew the oil fill cap and remove the dipstick
from the oil fill tube.
Snap the small end of oil drain sleeve onto the oil
sump. See Figure 22.

IMPORTANT: The use of a pressure washer or garden
hose to clean your tractor is NOT recommended. It may
cause damage to electrical components, spindles,
pulleys, bearings or the engine. The use of water will
result in a shortened life of the tractor and reduce its
serviceability.

Engine
Refer to the Briggs & Stratton Operator/Owner
Manual (or Tecumseh engine's Owner's Manual)
for engine maintenance instructions.

Oil Drain Sleeve

Check engine oil level before each use as instructed in
the Briggs & Stratton Operator/Owner Manual (or
Tecumseh engine's Owner's Manual) packed with your
unit. Follow the instructions carefully.

Figure 22
Remove drain plug and drain oil into a suitable
container with a capacity of no less than 64 oz.
Service the oil filter (if so equipped) as instructed
in the separate Briggs & Stratton Operator/Owner
Manual (or Tecumseh engine's Owner's Manual)
packed with your unit.
20

Air Cleaner

Perform the above steps in the opposite order after oil
has finished draining.
•

Service the pre-cleaner, if so equipped, and cartridge/
air cleaner element as instructed in the Briggs &
Stratton Operator/Owner Manual (or Tecumseh
engine's Owner's Manual) packed with your unit.

Refill the engine with new motor oil.

IMPORTANT: Refer to the Briggs & Stratton Operator/
Owner Manual (or Tecumseh engine's Owner's
Manual) packed with your unit for information regarding
the quantity and proper weight of motor oil.

Spark Plug(s)
The spark plug(s) should be
once a season. Refer to the
Operator/Owner Manual (or
Owner's Manual) for correct
specifications.

ChangingEngineOil
(modelsequippedwith an oil drain valve)

NOTE:

Depending on your tractor's engine make &
model, it may be necessary to remove the tractor's side
panel in order to replace the oil filter (if so equipped).
•

cleaned and the gap reset
Briggs & Stratton
Tecumseh engine's
plug type and gap

Lubrication
WARNING:

Before lubricating, repairing, or
inspecting, always place the PTO (blade
engage) lever in the BLADES STOP position,
move shift lever into neutral position, set
parking brake, stop engine and remove key to
prevent unintended starting.

Unscrew the oil fill cap and remove the dipstick
from the oil fill tube. See Figure 23.

Rear Wheels
The rear wheels should be removed from the axles
once a season. Lubricate the axles and the rims well

11Tube

with an all-purpose grease before re-installing them.
o

FrontAxles
Each end of the tractor's front pivot bar may be
equipped with a grease fitting. If so equipped, lubricate
with a grease gun after every 25 hours of tractor
operation.
Pivot Points & Linkage
Lubricate all the pivot points on the drive system,
clutch-brake pedal and lift linkage at least once a
season with light oil.

Drain Port

Figure 23

SteeringShaftand Gear
Lubricate teeth of steering gears with automotive multipurpose grease after every 25 hours of operation or
once a season. See Figure 24.

•

Pop open the protective cap on the end of the oil
drain valve to expose the drain port. See.
•
Push the oil drain hose (packed with this manual)
onto the oil drain port. Route the opposite end of
the hose into an appropriate oil collection container
with a capacity of no less than 64 oz.
•
Push the oil drain valve in slightly, then rotate
counterclockwise and pull outward to begin
draining oil.
•
Service the oil filter (if so equipped) as instructed
in the separate Briggs & Stratton Operator/Owner
Manual (or Tecumseh engine's Owner's Manual)
packed with your unit.
Perform the above steps in the opposite order after oil
has finished draining.
•

Refill the engine with new motor oil.

IMPORTANT: Refer to the Briggs & Stratton Operator/
Owner Manual (or Tecumseh engine's Owner's
Manual) packed with your unit for information regarding
the quantity and proper weight of motor oil.

Steering Shaft and Gear
Figure 24
21

SECTION8: SERVICE
WARNING:
Before
performing
any
maintenance or repairs, place the PTO (blade
engage) lever in the BLADES STOP position,
move shift lever into neutral position, set
parking brake, stop engine and remove key to
prevent unintended starting.

CuttingDeckRemoval
WARNING:

Shut the engine off, remove
ignition key, set the parking brake, disconnect
the spark plug wire(s) and ground against the
engine to prevent unintended starting before
removing the cutting deck.

Belt Keeper Pins

WARNING:
Always wear safety glasses or
safety goggles to protect your eyes while
removing the cutting deck.

Deck Anti-sway Rod

Deck Belt
Figure 25

For performing service on your tractor and in order to
properly mount some (separately available)
attachments, it may be necessary to remove the
tractor's cutting deck. To due so, proceed as follows:

38- and 42-inch Decks
Place the PTO (blade engage) lever in the BLADES
STOP (all the way back) position.
Locate the two belt keeper pins, found on either
side of the engine pulley, and use a 1/4-inch socket
wrench to remove them from the lower frame. See
Figure 25.
,/

NOTE:

When reassembling, make certain belt keeper
pins are assembled in the same locations from which
they were removed
•

•

•
•

•

Deck Anti-sway Rod
and Hairpin Clip

Deck Hangers

Remove the deck belt from around the engine
pulley and place the PTO (blade engage) lever in
the engaged (all the way forward) position.
Locate the deck anti-sway rod and deck hangers
found near the front of the cutting deck. See Figure
25 & Figure 26.
First remove the hairpin clip which secures the antisway rod to the front portion of the cutting deck,
then remove the hairpin clips which secure the deck
hangers. Retain the hairpin clips.
Carefully lower the front portion of the deck to the
ground.
Gently nudge the deck rearward, and disconnect
the spring from the deck stabilizer bracket. See
Figure 27.
Remove the hairpin clips which secure the rear
deck hangers to the deck stabilizer bracket. See
Figure 27. Retain the hairpin clips.

Figure 26

Stabilizer
Bracket

...................................................
/

Figure 27
22

Spring

•
•

•

Carefully lower the rear portion of the deck to the
ground.
Place the PTO (blade engage) lever in the BLADES
STOP position to raise the lift links up, and out of
the way.

Remove the hairpin clips which secure the rear
deck hangers to the deck stabilizer bracket. See
Figure 29. Retain the hairpin clips.
Rear Deck Hangers

46-inch Decks
Place the PTO (blade engage) lever in the engaged
(all the way forward) position.
Using a spring puller (MTD Part No. 732-0571 )or
other suitable tool, disconnect the spring which is
attached to a small hook found on the left, rear
portion of the transmission. See Figure 28.

Stabilizer Bracket

Hook
/
Figure 29
Carefully lower the rear portion of the deck to the
ground.

NOTE:

For normal service and maintenance, the
deck stabilizer bracket doesn't need to be removed

Spring

from the tractor. If removing the cutting deck in order to
mount a Snow Thrower attachment, however, the
stabilizer bracket must be removed. To do so, simply
remove the hairpin clip which secures the stabilizer rod
to the stabilizer bracket. See Figure 29.

Transmission

•

Figure 28

Place the PTO (blade engage) lever in the BLADES
STOP position to raise the lift links up, and out of
the way.
Carefully slide the deck from beneath the right side
of the lawn tractor.

Place the PTO (blade engage) lever in the BLADES
STOP position.

•

Locate the two belt keeper pins, found on either
side of the engine pulley, and use a 1/4-inch socket
wrench to remove them from the lower frame. See

CuttingBlades

Figure 25.
WARNING:
Be sure to shut the engine off,
remove ignition key, disconnect the spark plug
wire(s) and ground against the engine to
prevent unintended starting before removing
the cutting blade(s) for sharpening
or
replacement. Protect your hands by using
heavy gloves or a rag to grasp the cutting
blade.

NOTE:

When reassembling, make certain belt keeper
pins are assembled in the same locations from which
they were removed.
•

•

Remove the deck belt from around the engine
pulley.Return the PTO (blade engage) lever to the
engaged (all the way forward) position.
Locate the deck anti-sway rod and deck hangers
found near the front of the cutting deck. See Figure
25 & Figure 26.
First remove the hairpin clip which secures the antisway rod to the front portion of the cutting deck,
then remove the hairpin clips which secure the deck
hangers. Retain the hairpin clips.

WARNING:
Periodically inspect the blade
adapter and/or spindle for cracks or damage,
especially if you strike a foreign object.
Replace immediately if damaged.

Carefully lower the front portion of the deck to the
ground.
23

The blades may be removed as follows.
•

•

It is important that each cutting blade edge be ground
equally to maintain proper blade balance. A poorly
balanced blade will cause excessive vibration and may
cause damage to the tractor and result in personal
injury.

Remove the deck from beneath the tractor, (refer to
CuttingBeck Removalon page 22) then gently flip the
deck over to expose its underside.
Place a block of wood between the center deck
housing baffle and the cutting blade to act as a
stabilizer. See Figure 30.

The blade can be tested by balancing it on a round
shaft screwdriver. Grind metal from the heavy side until
it balances evenly.

Hex Flange Nut

When replacing the blade, be sure to install the blade
with the side of the blade marked "Bottom" (or with a
part number stamped in it) facing the ground when the
mower is in the operating position.

IMPORTANT: Use a torque wrench to tighten the blade
spindle hex flange nut to between 70 foot-pounds and
90 foot-po unds.

Battery
The battery is sealed and is maintenance-free.
levels cannot be checked.
•
•

Spindle Assembly

Figure 30
•

•

Use a 15/16" wrench to remove the hex flange nut
that secures the blade to the spindle assembly. See
Figure 30.
To properly sharpen the cutting blades, remove equal
amounts of metal from both ends of the blades along
the cutting edges, parallel to the trailing edge, at a 25 °
to 30 ° angle. See Figure 31.

Always keep the battery cables and terminals clean
and free of corrosive build-up.
After cleaning the battery and terminals, apply a
light coat of petroleum jelly or grease to both
terminals
Always keep the rubber boot positioned over the
positive terminal to prevent shorting.

IMPORTANT:If removing the battery for any reason,
disconnect the NEGATIVE (Black) wire from it's
terminal first, followed by the POSITIVE (Red) wire.
When re-installing the battery, always connect the
POSITIVE (Red) wire its terminal first, followed by the
NEGATIVE (Black) wire. Be certain that the wires are
connected to the correct terminals; reversing them
could change the polarity and cause damage to your
engine's alternating system.

Blade Separation

Acid

Charging
If the tractor has not been put into use for an extended
period of time, charge the battery with an automotivetype 12-volt charger for a minimum of one hour at six
amps.

Worn Blade Edge
Wind Wing

WARNING:
Batteries give off an explosive
gas while charging. Charge battery in a well
ventilated area and keep away from an open
flame or pilot light as on a water heater, space
heater, furnace, clothes dryer or other gas
appliances.

Sharpen Edge Evenly

Jump Starting
Figure 31
IMPORTANT: If the cutting edge of the blade has already
been sharpened to within 5/8" of the wind wing radius,
or if any metal separation is present, replace the blades
with new ones. See Figure 31.

the battery, follow
instructions
to
WARNING:
When these
removing
or installing
prevent the screwdriver from shorting against
the frame.

IMPORTANT: Never jump your tractor's dead battery
with the battery of a running vehicle.
•

•

BeckBelt (38- and 42-inch Decks)

WARNING:

Shut the engine off, remove
ignition key, set the parking brake, disconnect
the spark plug wire(s) and ground against the
engine to prevent unintended starting before
removing the cutting deck.

Connect end of one jumper cable to the positive
terminal of the good battery, then the other end to
the positive terminal of the dead battery.
Connect the other jumper cable to the negative
terminal of the good battery, then to the frame of
the unit with the dead battery.
_
could
cause sparking,
anduse
thethis
gasprocedure
in either
WARNING:
Failure to
battery could explode.

•

Cleaning
Clean the battery by removing it from the tractor and
washing with a baking soda and water solution. If
necessary, scrape the battery terminals with a wire
brush to remove deposits. Coat terminals and exposed
wiring with grease or petroleum jelly to prevent
corrosion.

•

safety
goggles Always
to protect
while
ARNING:
wear your
safetyeyes
glasses
or
removing the cutting deck.
Remove the cutting deck from the tractor (Refer to
CuttingDeckRemovalon page 22, for detailed
instructions).
Remove the belt guards (located over each spindle
pulley) by removing the self-tapping screws which
secure them in place. See Figure 32.

Self-Tapping
Screws

Battery Failures
Some common causes for battery failure are:
• incorrect initial activation
• undercharging
• overcharging
• corroded connections
• freezing
These failures are NOT covered by your tractor's
warranty.

Tires
Recommended operating tire pressure is
approximately 10 p.s.i. Maximum tire pressure under
any circumstances is 30 p.s.i. Equal tire pressure
should be maintained on all tires.

Belt Guards
42-inch deck Shown

When installing a tire to the rim, be certain rim is clean
and free of rust. Lubricate both the tire and rim
generously. Never inflate to over 30 p.s.i, to seat
beads.

Figure 32
•

Remove and replace the belt, reassemble following
the instructions in reverse order.

DeckBelts (48" Deck)
,_

•

p.s.i.)
when seating
beads pressure
may cause(over
tire/rim
WARNING:
Excessive
30
assembly to burst with force sufficient to
cause serious injury.

Remove the cutting deck from the tractor (Refer to
CuttingDeckRemovalon page 22, for detailed
instructions)

NOTE: On 46-inch decks, you must also remove both

BeltReplacement

the deck stabilizer bracket and the stabilizer rod. To do
so, remove the hairpin clip which secures the stabilizer
rod to the stabilizer bracket. See Figure 33.

WARNING:

Shut the engine off, remove
ignition key, set the parking brake, disconnect
the spark plug wire(s) and ground against the
engine to prevent unintended starting before
replacing belts.

•

After the deck is removed (and the stabilizer
bracket and rod), the upper deck belt can be simply
lifted off of the double-pulley located in the rear,
center of the cutting deck.
To remove the lower deck belt:

For performing service on your tractor and in order to
properly mount some (separately available)
attachments, it may be necessary to remove the
tractor's cutting deck. To due so, proceed as follows:

•

Follow all steps above for removing the upper deck
belt.

•

•
•

Remove the belt guards (located over each outer
spindle pulley) by removing the self-tapping screws
which secure them in place. Refer Figure 32.
Using a spring puller (MTD Part No. 732-0571 )or
other suitable tool, disconnect the extension spring
from the rear of the cutting deck belt. This will
relieve tension on the lower deck belt.
Remove the lower deck belt from around the idler
pulleys, and the three spindle pulleys.
Reassemble new belts, following instructions in
reverse order.

Stabilizer Rod_
Hairpin Clip

Drive Belts(Upper and Lower)

NOTE:

The engine pufley must be removed from the
engine's crankshaft in order to change the tractor's
drive belts. Doing so requires an air/impact wrench.
It is recommended that both drive belts be changed at
the same time.

Figure 33

Place the PTO (blade engage) lever in the engaged
(all the way forward) position.
Unthread the shift knob and remove the two flange
screws which secure the shift cover panel in place.
Refer to Figure 15. Remove the shift cover panel.

Springs

NOTE:

There is a small yeflow wire connected to a
spring switch on the underside of the shift cover panel.
Be careful not to damage it when removing the panel.
•

•
•

Using a spring puller (MTD Part No. 732-0571 )or
other suitable tool, disconnect the spring which is
attached to a small hook found on the left, rear
portion of the transmission (Refer to Figure 28) and
the two springs which are attached to the rear
portion of the tractor frame. See to Figure 34.
Place the PTO (blade engage) lever in the BLADES
STOP position.
Locate the two belt keeper pins, found on either
side of the engine pulley, and use a 1/4-inch socket
wrench to remove them from the lower frame. Refer

Figure 34

to Figure 25.

NOTE:

When reassembling, make certain belt keeper
pins are assembled in the same locations from which
they were removed.
•

•
•

Using an impact gun with a 5/8-inch socket, remove
the hex screw with secures the engine pulley to the
engine crankshaft.
Carefully lower the pulley off of the crankshaft and
remove the belt from around it.
Disconnect the battery cables from the terminals
(disconnect the NEGATIVE (Black) wire from it's
terminal first, followed by the POSITIVE (Red)
wire).
Detach the battery hold-down rod and remove both
the battery and battery tray from the tractor.
Locate the transmission pulley though the battery
tray opening. See Figure 35.

Figure 35
26

•

Using an impact gun with a 13/16-inch socket,
remove the pulley from the transmission's input
shaft by removing the flange nut which secures it
Carefully lift the pulley off of the transmission's
input shaft and remove the upper drive belt from
around it and the variable speed.

•

Remove the lower drive belt by lifting it through the
cover panel opening.

•

Reassemble new belts, following the previous
instructions in reverse order.

IMPORTANT: When remounting the engine pulley,

NOTE:

A spacer is located beneath the transmission
pulley. Be careful not to lose the spacer and be certain
NOT reinstall the spacer upside down.

torque the hex bolt to between 38 foot-pounds and 50
foot-pounds.

•

IMPORTANT: When remounting the transmission pulley,
torque the flange nut to between 25 foot-pounds and 33

Remove the lower drive belt from around the lower
portion of the variable speed pulley and feed it
toward the shift cover panel opening.

foot-pounds.

SECTION9: OFF-SEASON
STORAGE
WARNING:
Never store the machine or
fuel container indoors where there is an

pipes, and otherExtinguish
sources of
ignition prior
to
WARNING"
cigarettes,
cigars,
draining fuel.

open flame, spark or pilot light such as on
water heater, furnace, clothes dryer or other
gas appliance.

Charge battery fully. NEVER store battery without a
full charge. Recharge battery before returning to
service or every two months, whichever occurs first.

If the machine is to be inoperative for a period longer
than 30 days, prepare for storage as follows.
•
•
•

•

Clean the engine and the entire unit thoroughly.
Refer to Page 20.
Lubricate all lubrication points. Wipe the entire
machine with an oiled rag to protect the surfaces.
Refer to the engine manual for correct engine
storage instructions. The engine must be
completely drained of fuel to prevent gum deposits
from forming on essential carburetor parts, fuel
lines and fuel tank.

•

When storing unit for extended periods, disconnect
battery cables. Removing battery from unit is
recommended.
Store unit in a clean, dry area. Do not store next to
corrosive materials, such as fertilizer.

NOTE:

When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rustproof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.

SECTION10: ATTACHMENTS
& ACCESSORIES
The following attachments and accessories are compatible for Lawn Tractor Models 660-668. See the retailer
from which you purchased your tractor, an authorized MTD Service Dealer or phone (800) 800-7310 for information
regarding price and availability. Your lawn tractor is NOT designed for use with any type of ground-engaging
attachments (e.g. tiller or plow). Use of this type of equipment WILL void the tractor's warranty.
MODEL
0EM-190-116
0EM-190-118
0EM-190-180
0EM-190-182
0EM-190-215
0EM-190-226
0EM-190-620
0EM-190-627
0EM-190-916
0EM-190-658
0EM-190-657
0EM-190-754
0EM-190-664
0EM-190-808

DESCRIPTION
42-inch Deck Mulch Kit
46-inch Deck Mulch Kit
Twin Bagger Grass Collector (for 38- and 42-inch Decks)
Twin Bagger Grass Collector (for 46-inch Decks)
Rear Wheel Weights (Two per set)
Front Bumper Kit
46-inch Front Dozer Blade
42-inch Two-stage Snow Thrower
Tire Chains, for 20" x 10.0" tires (Two per set)
Tire Chains, for 20" x 8.0" tires (Two per set)
Tire Chains, for 18" x 9.5" tires (Two per set)
Tire Chains, for 18" x 8.5" tires (Two per set)
Tire Chains, for 18" x 6.5" tires (Two per set)
Deluxe Tractor Sunshade

SECTION11: TROUBLE
SHOOTING
GUIDE
Trouble

Possible

Engine will not
crank

Safety switch button
not depressed.
Battery installed
incorrectly.

Engine cranks
but will not start

Engine smokes

Excessive
vibration

Mower will not
discharge grass
or leaves uncut
strips

NOTE:

Cause(s)

Battery is dead or
weak.
Blown fuse or circuit
breaker.
Engine ground wire
loose.
Throttle / Choke not
in correct position.
No fuel to the carburetor.
No spark to spark
plug.
Dirty air cleaner.
Engine oil has been
overfilled.
Engine loses crankcase vacuum.
Bent or
damaged blade.
Bent blade.

Corrective

Action

There are two switches in the starting circuit of your unit: the clutch pedal switch and
the PTO (blade engage) lever switch. Make certain the actuator is fully depressing the
buttons on each switch.
The battery must be installed with negative terminal attached to black ground wire.
Negative terminal is identified at the post by "NEG", "N" or "-". The positive terminal,
identified by "POS", "P" or "+", must be attached to the big red wire which goes to the
solenoid. All batteries are to be fully charged before installing.
Charge with 6 AMP charger until fully charged.
Refer to schematic for fuse location and replace fuse if blown. If fuse blows repeatedly, see an authorized service dealer to have the tractor's wire harness serviced.
Engine should have a black ground wire running from engine to frame or mounting
bolt.
Refer to Starting the Enginein this manual for correct position of the throttle control and
choke control.
Gasoline tank empty. Fill with clean, fresh gasoline.
Fuel line or in-line fuel filter plugged. Remove and clean fuel line. Replace filter if
necessary.
Spark plug lead disconnected. Connect lead.
Faulty spark plug. Replace spark plug.
Refer to the engine manual packed with your unit. If the air cleaner is dirty, replace it
Check oil level. Drain as necessary.

Dipstick not seated or broken. Replace dipstick.
Engine breather defective. Replace.
Stop engine immediately. Check all pulleys, blade adapters, keys and bolts for
tightness and spindle damage. Tighten or replace any damaged parts.
Stop engine immediately. Replace damaged blade. Only use original equipment
blades.
Engine speed low.
Always operate the cutting deck with throttle control set in the FAST (rabbit) position.
Speed selection.
Slow your ground speed. The slower your ground speed, the better the quality of cut.
Cutting height set too Raise deck.
low.
Blades short or dull.
Sharpen or replace blades (uncut strip problem only).

For repairs beyond the minor adjustments above, contact your local authorized service dealer.

NOTES

MANUFACTURER'S

LIMITED WARRANTY

The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the
United States, its possessions and territories.
"MTD"warrants this product against defects in material and
workmanship for a period of two (2) years commencing on the
date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in
materials or workmanship. This limited warranty shall only
apply if this product has been operated and maintained in
accordance with the Operator's Manual furnished with the
product, and has not been subject to misuse, abuse,
commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this
manual will void your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in
material and workmanship for a period of thirty (30) days from
the date of purchase. Normal wear parts include, but are not
limited to items such as: batteries, belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow thrower
skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area, check your
Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1330-220-4683 or log on to our Web site at
www.mtdproducts.com.
This limited warranty does not provide coverage in the
following cases:
a.

b.
c.

The engine or component parts thereof. These items
may carry a separate manufacturer's warranty. Refer
to applicable manufacturer's warranty for terms and
conditions.
Log splitter pumps, valves, and cylinders have a
separate one year warranty.
Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal
deterioration of the exterior finish due to use or

FOR:

MTD does not extend any warranty for products sold or
exported outside of the United States, its possessions
and territories, except those sold through MTD's
authorized channels of export distribution.
Replacement parts that are not genuine MTD parts.
Transportation charges and service calls.

No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind MTD. During the period of the warranty, the
exclusive remedy is repair or replacement of the product
as set forth above.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. MTD
shall not be liable for incidental or consequential loss or
damage including, without limitation, expenses incurred
for substitute or replacement lawn care services or for
rental expenses to temporarily replace a warranted
product.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

IMPORTANT:Owner must present Original Proof of
Purchase to obtain warranty coverage.

exposure.
Service completed by someone other than an
authorized service dealer.

MTD LLC, P.O.BOX361131CLEVELAND,OHIO44136-0019; Phone:1-800-800-7310,1-330-220-4683

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 32
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sat Mar 29 02:03:32 2014
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

MTD 13AF685G700 User Manual LAWN TRACTOR Manuals And Guides 1109238L

Navigation menu

Versions of this User Manual:

Views

Navigation