MTD 808H 769 00595 User Manual To The 68738d2c Ecbc 4870 Bedf 14d30fab83ad

User Manual: MTD 808H to the manual

Open the PDF directly: View PDF .
Page Count: 48

PRINTED IN U.S.A. 769-00595.fm

(12/2002)

FORM NO.

Operator’s Manual

Pedal Drive

Garden Tractor

Model Series

808H & 808K

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Warning:

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-cov-

ered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable

local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State

of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer

or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

2

TABLE OF CONTENTS

Content Page

Important Safe Operation Practices................................................................... 3

Slope Gauge...................................................................................................... 6

Tractor Set-up.................................................................................................... 7

Know Your Garden Tractor ................................................................................ 10

Operating Your Garden Tractor ......................................................................... 13

Making Adjustments .......................................................................................... 16

Maintaining Your Garden Tractor ...................................................................... 18

Service .............................................................................................................. 19

Off-Season Storage........................................................................................... 24

Attachments & Accessories ............................................................................... 24

Troubleshooting................................................................................................. 25

Parts List............................................................................................................ 26

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new Garden Tractor. It will help you assemble, prepare and

maintain the unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the

equipment and copy the information from it in the space provided below. This information is very

important if you need help from our Customer Support Department or an authorized dealer.

• Locate the model number by looking beneath the seat. A sample model plate is explained below. For

future reference, please copy the model and the serial numbers of the equipment in the space below.

ENGINE INFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating,

specifications, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual

packed separately with your unit for more information.

CALLING CUSTOMER SUPPORT

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, please call the Customer Support Department.

Call 1- (330) 220-4MTD (4683) or 1- (800)-800-7310 to reach a Customer Support

representative. Please have your unit’s model number and serial number ready when you call.

See previous section to locate this information. You will be asked to enter the serial

Copy the model number here:

Copy the serial number here:

For more details about your unit, visit our website at www.mtdproducts.com

3

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

General Operation

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place

for future and regular reference and for ordering

replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them

quickly.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the operation instructions and safety rules in

this manual and should be trained and supervised by a

parent.

4. Never allow adults to operate this machine without proper

instruction.

5. To help avoid blade contact or a thrown object injury,

keep bystanders, helpers, children and pets at least 75

feet from the machine while it is in operation. Stop

machine if anyone enters the area.

6. Thoroughly inspect the area where the equipment is to be

used. Remove all stones, sticks, wire, bones, toys, and

other foreign objects which could be picked up and

thrown by the blade(s). Thrown objects can cause

serious personal injury.

7. Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or obstruction

which may cause discharged material to ricochet back

toward the operator.

8. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

9. Wear sturdy, rough-soled work shoes and close-fitting

slacks and shirts. Loose fitting clothes and jewelry can be

caught in movable parts. Never operate this machine in

bare feet or sandals.

10. Be aware of the mower and attachment discharge

direction and do not point it at anyone. Do not operate the

mower without the discharge cover or entire grass

catcher in its proper place.

11. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade(s) can amputate

hands and feet.

12. A missing or damaged discharge cover can cause blade

contact or thrown object injuries.

13. Stop the blade(s) when crossing gravel drives, walks, or

roads and while not cutting grass.

14. Watch for traffic when operating near or crossing

roadways. This machine is not intended for use on any

public roadway.

15. Do not operate the machine while under the influence of

alcohol or drugs.

16. Mow only in daylight or good artificial light.

17. Never carry passengers.

18. Disengage blade(s) before shifting into reverse. Back up

slowly. Always look down and behind before and while

backing to avoid a back-over accident.

19. Slow down before turning. Operate the machine

smoothly. Avoid erratic operation and excessive speed.

20. Disengage blade(s), set parking brake, stop engine and

wait until the blade(s) come to a complete stop before

removing grass catcher, emptying grass, unclogging

chute, removing any grass or debris, or making any

adjustments.

21. Never leave a running machine unattended. Always turn

off blade(s), place transmission in neutral, set parking

brake, stop engine and remove key before dismounting.

22. Use extra care when loading or unloading the machine

into a trailer or truck. This unit should not be driven up or

down ramp(s), because the unit could tip over, causing

serious personal injury. The unit must be pushed

manually on ramp(s) to load or unload properly.

23. Muffler and engine become hot and can cause a burn. Do

not touch.

24. Check overhead clearances carefully before driving

under low hanging tree branches, wires, door openings

etc., where the operator may be struck or pulled from the

unit, which could result in serious injury.

25. Disengage all attachment clutches, depress the brake

pedal completely and shift into neutral before attempting

to start engine.

26. Your machine is designed to cut normal residential grass

of a height no more than 10”. Do not attempt to mow

WARNING:

This symbol points out important safety instructions which, if not followed, could endanger

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual

before attempting to operate this machine. Failure to comply with these instructions may result in personal

injury. When you see this symbol—heed its warning.

DANGER:

This machine was built to be operated according to the rules for safe operation in this manual.

As with any type of power equipment, carelessness or error on the part of the operator can result in serious

injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury or death.

WARNING:

Engine exhaust, some of its constituents, and certain vehicle components contain or

emit chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm.

4

through unusually tall, dry grass (e.g., pasture) or piles of

dry leaves. Dry grass or leaves may contact the engine

exhaust and/or build up on the mower deck presenting a

potential fire hazard.

27. Use only accessories and attachments approved for this

machine by the machine manufacturer. Read,

understand and follow all instructions provided with the

approved accessory or attachment.

28. Data indicates that operators, age 60 years and above,

are involved in a large percentage of riding mower-

related injuries. These operators should evaluate their

ability to operate the riding mower safely enough to

protect themselves and others from serious injury.

29. If situations occur which are not covered in this manual,

use care and good judgment. Contact an authorized

Service Dealer for assistance.

Slope Operation

Slopes are a major factor related to loss of control and tip-

over accidents which can result in severe injury or death. All

slopes require extra caution. If you cannot back up the slope

or if you feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of this

manual to measure slopes before operating this unit on a

sloped or hilly area. If the slope is greater than 15 degrees as

shown on the slope gauge, do not operate this unit on that

area or serious injury could result.

Do:

1. Mow up and down slopes, not across. Exercise extreme

caution when changing direction on slopes.

2. Watch for holes, ruts, bumps, rocks, or other hidden

objects. Uneven terrain could overturn the machine. Tall

grass can hide obstacles.

3. Use slow speed. Choose a low enough speed setting so

that you will not have to stop or shift while on the slope.

Tires may lose traction on slopes even though the brakes

are functioning properly. Always keep machine in gear

when going down slopes to take advantage of engine

braking action.

4. Follow the manufacturer’s recommendations for wheel

weights or counterweights to improve stability.

5. Use extra care with grass catchers or other attachments.

These can change the stability of the machine.

6. Keep all movement on the slopes slow and gradual. Do

not make sudden changes in speed or direction. Rapid

engagement or braking could cause the front of the

machine to lift and rapidly flip over backwards which

could cause serious injury.

7. Avoid starting or stopping on a slope. If tires lose traction,

disengage the blade(s) and proceed slowly straight down

the slope.

Do Not:

1.

Do not turn on slopes unless necessary; then, turn slowly

and gradually downhill, if possible.

2. Do not mow near drop-offs, ditches or embankments.

The mower could suddenly turn over if a wheel is over the

edge of a cliff, ditch, or if an edge caves in.

3. Do not try to stabilize the machine by putting your foot on

the ground.

4. Do not use a grass catcher on steep slopes.

5. Do not mow on wet grass. It may cause sliding.

6. Do not shift to neutral and coast downhill. Over-speeding

may cause the operator to lose control of the machine

resulting in serious injury or death.

7. Do not tow heavy attachments (e.g. loaded dump cart,

lawn roller, etc.) on slopes greater than 5 degrees. When

going down hill, the extra weight tends to push the tractor

and may cause you to loose control. (e.g. tractor may

speed up, braking and steering ability may be reduced,

attachment may jack-knife and tractor may overturn).

Children

1. Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. They do not

understand the dangers. Never assume that children will

remain where you last saw them.

a. Keep children out of the mowing area and in

watchful care of a responsible adult other than the

operator.Be alert and turn machine off if a child

enters area.

b. Before and while backing, look behind and down

for small children.

c. Never carry children, even with the blade(s) shut

off. They may fall off and be seriously injured or

interfere with safe machine operation.

d. Use extreme care when approaching blind

corners, doorways, shrubs, trees or other objects

that may block your vision of a child who may run

into the machine.

e. Disengage the cutting blade(s) before shifting in

reverse. The “No-Cut-In Reverse” feature is a

reminder not to cut in reverse and to help avoid

back over accidents. Do not defeat it.

f. Keep children away from hot or running engines.

They can suffer burns from a hot muffler.

g. Remove key when machine is unattended to

prevent unauthorized operation.

8. Never allow children under 14 years to operate the

machine. Children 14 years old and over should read and

understand the operation and safety rules in this manual

and should be trained and supervised by a parent.

Towing

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

2. Follow the manufacturers recommendation for weight

limits for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast downhill.

Service

Safe Handling Of Gasoline:

1. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is

5

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite. Wash

your skin and change clothes immediately.

a. Use only an approved gasoline container.

b. Never fill containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place

containers on the ground away from your vehicle

before filling.

c. When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the ground.

If this is not possible, then refuel such equipment

on a trailer with a portable container, rather than

from a gasoline dispenser nozzle.

d. Keep the nozzle in contact with the rim of the fuel

container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

e. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

f. Never fuel machine indoors.

g. Never remove gas cap or add fuel while the

engine is hot or running. Allow engine to cool at

least two minutes before refueling.

h. Never over fill fuel tank. Fill tank to no more than

½ inch below bottom of filler neck to allow space

for fuel expansion.

i. Replace gasoline cap and tighten securely.

j. If gasoline is spilled, wipe it off the engine and

equipment. Move unit to another area. Wait 5

minutes before starting the engine.

k. To reduce fire hazards, keep machine free of

grass, leaves, or other debris build-up. Clean up

oil or fuel spillage and remove any fuel soaked

debris.

l. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

as on a water heater, space heater, furnace,

clothes dryer or other gas appliances.

m. Allow a machine to cool at least 5 minutes before

storing.

General Service:

1. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless, and deadly gas.

2. Before cleaning, repairing, or inspecting, make certain

the blade(s) and all moving parts have stopped.

Disconnect the spark plug wire and ground against the

engine to prevent unintended starting.

3. Periodically check to make sure the blades come to

complete stop within approximately (5) five seconds after

operating the blade disengagement control. If the blades

do not stop within the this time frame, your unit should be

serviced professionally by an authorized Service Dealer.

4. Check brake operation frequently as it is subjected to

wear during normal operation. Adjust and service as

required.

5. Check the blade(s) and engine mounting bolts at

frequent intervals for proper tightness. Also, visually

inspect blade(s) for damage (e.g., excessive wear, bent,

cracked).

Replace the blade(s) with the original equipment

manufacturer’s (O.E.M.) blade(s) only, listed in this

manual. “Use of parts which do not meet the original

equipment specifications may lead to improper

performance and compromise safety!”

6. Mower blades are sharp. Wrap the blade or wear gloves,

and use extra caution when servicing them.

7. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

8. Never tamper with the safety interlock system or other

safety devices. Check their proper operation regularly.

9. After striking a foreign object, stop the engine, disconnect

the spark plug wire(s) and ground against the engine.

Thoroughly inspect the machine for any damage. Repair

the damage before starting and operating.

10. Never attempt to make adjustments or repairs to the

machine while the engine is running.

11. Grass catcher components and the discharge cover are

subject to wear and damage which could expose moving

parts or allow objects to be thrown.

For safety protection, frequently check components and

replace immediately with original equipment

manufacturer’s (O.E.M.) parts only, listed in this manual.

“Use of parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safety!”

12. Do not change the engine governor settings or over-

speed the engine. The governor controls the maximum

safe operating speed of the engine.

13. Maintain or replace safety and instruction labels, as

necessary.

14. Observe proper disposal laws and regulations for gas,

oil, etc. to protect the environment.

Your Responsibility

• Restrict the use of this power machine to persons who

read, understand and follow the warnings and

instructions in this manual and on the machine.

TO REDUCE THE RISK OF INJURY, DO NOT

OPERATE UNLESS DISCHARGE COVER OR

GRASS CATCHER IS IN ITS PROPER PLACE.

IF DAMAGED, REPLACE IMMEDIATELY.

KEEP HANDS AND FEET AWAY FROM ROTATING PARTS.

REMOVE OBJECTS THAT CAN BE THROWN BY THE

BLADE IN ANY DIRECTION. WEAR SAFETY GLASSES.

DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.

NEVER CARRY CHILDREN EVEN WITH BLADES OFF.

USE EXTRA CAUTION ON SLOPES. DO NOT MOW SLOPES

GREATER THAN 10° MOW UP AND DOWN, NOT ACROSS.

AVOID SUDDEN TURNS, USE LOW GEAR.

MAX 10°

READ OPERATOR'S MANUAL. KEEP SAFETY DEVICES IN PLACE AND WORKING.

AVOID SERIOUS INJURY OR DEATH

S30536

x

6

SECTION 2: SLOPE GAUGE

15°

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

A POWER POLE

A CORNER OF A BUILDING

OR A FENCE POST

FOLD ON DOTTED LINE, REPRESENTING A 15° SLOPE

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower

could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain

your footing and you could slip, resulting in serious injury.

Operate RIDING mowers up and down slopes, never across the face of slopes.

WARNING

7

SECTION 3: SETTING UP THE TRACTOR

NOTE: Any reference here to the RIGHT or LEFT side

of the tractor is observed from operator’s position.

Attaching Battery Cables

NOTE: The positive battery terminal is marked Pos. (+).

The negative battery terminal is marked Neg. (–).

• The positive cable (heavy red wire) is secured to

the positive battery terminal (+) with a hex bolt and

hex nut at the factory. Make certain that the rubber

boot covers the terminal to help protect it from

corrosion.

• Remove the hex bolt and wing nut from the

negative cable.

• Remove the black plastic cover, if present, from the

negative battery terminal and attach the negative

cable (heavy black wire) to the negative battery

terminal (–) with the bolt and wing nut.

• Make certain the hold-down strap is in position over

the battery, securing it in place. See Figure 1.

Figure 1

NOTE: If the battery is put into service after the date

shown on top of battery, charge the battery as

instructed on page 23 of this manual prior to operating

the tractor.

Gas and Oil Fill-up

The gasoline tank is located under the hood and has a

capacity of either two or three gallons. Do not overfill.

Service the engine with gasoline and oil as instructed in

the separate Briggs & Stratton Operator/Owner Manual

packed with your tractor. Read instructions carefully.

IMPORTANT:

Your tractor is shipped with motor oil in

the engine. However, you must check the oil level

before operating. Be careful not to overfill.

Shipping Brace Removal

• Locate the shipping brace and accompanying

warning tag on the right side of the tractor, between

the discharge chute and the deck. See Figure 2.

Figure 2

• While holding the discharge chute with your left

hand, remove the shipping brace with your right

hand by grasping it between your thumb and index

finger and rotating it clockwise.

Attaching the Deck (Model 808K only)

WARNING:

Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Never

fuel machine indoors or while the engine is hot

or running. Extinguish cigarettes, cigars, pipes,

and other sources of ignition.

Hex Bolt

Wing

Nut

Rubber

Boot

WARNING:

Make sure the tractor engine is

off. Remove ignition key, and set the parking

brake before removing the shipping brace

.

WARNING:

The shipping brace, used for

packaging purposes only, must be removed

and discarded before operating tractor.

WARNING:

The mowing deck is capable of

throwing objects. Failure to operate the tractor

without the discharge cover in the proper

operating position could result in serious

personal injury and/or property damage.

WARNING:

Before attaching the cutting

deck, engage the parking brake, turn the

ignition key to the OFF position and remove the

key from the switch to avoid accidental starting.

Shipping Brace

Warning Tag

8

• Adjust the deck roller height so that the clevis pins

are inserted in the second hole (from the top) of

both the left-hand deck roller bracket and the right-

hand deck roller bracket. See Figure 5 or refer to

Deck Roller Height Adjustment on page 9 for more

detailed instructions on adjusting the deck roller

upward or downward.

• Raise the deck lift arms up and out of the way by

placing the deck lift lever in the top notch on the

right fender.

• Gently slide the cutting deck beneath the tractor

from the right side.

• Move the cutting deck into position so that the

hooks found on the front end of the deck fit snugly

around the deck stabilizer rod.

Figure 3

NOTE: The stabilizer rod may be secured to the tractor

frame with a plastic cable tie for shipping reasons. If so,

carefully cut the cable tie before mounting the front of

the cutting deck.

• Lower the deck lift arms by placing the lift lever in

the bottom notch on the right fender.

• Pull the deck support pin (on the left side of the

deck) outward and align it with the hole on the rear

of the left deck lift arm before releasing the pin to

lock it in place as shown in Figure 5. Repeat on the

right side.

Installing the PTO/Deck Belt

• Make certain that the PTO/Deck belt is routed

around the spindle pulleys (found beneath the belt

guards) and both idler pulleys as illustrated in

Figure 4 before proceeding.

• Relieve tension on the deck idler by inserting a 3/8”

drive ratchet wrench (set to “loosen”) in the hole

found in the idler bracket and pivoting the wrench

handle counterclockwise. See Figure 4.

IMPORTANT:

Be certain that the FLAT side of the PTO/

Deck belt is the side coming in contact with the deck

idler pulleys.

• With the tension relieved, carefully route the belt

around the electric PTO clutch.

NOTE: If necessary, refer to the decal found on the

deck’s surface or on page 19 of this manual for a

detailed belt-routing diagram.

Deck Support Pins

Deck Stabilizer Bracket

Deck Stabilizer Rod

Deck Lift Arms

Electric PTO Clutch

Deck Idler Pulleys

Front of Tractor

NOTE:

Many tractor components not shown for clarity.

PTO / Deck Belt

Deck Lift Assembly

Lift Lever

Notches

Fender

Lift Cables

Discharge Chute

Belt Guard

Belt Guard

Deck Roller Bracket

9

Figure 4

Deck Roller Height Adjustment

To adjust the height of the rollers found on the rear of

the mowing deck upward or downward, proceed as

follows:

• Place the deck lift lever in the bottom notch (lowest

position).

• Remove the clevis pins and hairpin clips from the

deck roller brackets on the left and right sides of the

cutting deck. See Figure 5.

• Position the deck roller brackets up or down

through the slots on the rear of the deck until

desired position is reached, then re-attach with the

clevis pins and hairpin clips just removed. See

Figure 5.

IMPORTANT:

Be certain that the left roller bracket and

the right roller bracket are set in the same position.

IMPORTANT:

After mounting the cutting deck, perform

any adjustments on the deck, if necessary, prior to

operating the tractor. Refer to page 16 for instructions. Figure 5

Left-hand Idler Bracket

3/8” Square Hole

Spring

Belt Guard

Idler Pulley

Hairpin Clip

Clevis pin

Deck Roller Bracket

10

SECTION 4: KNOW YOUR GARDEN TRACTOR

Figure 6

A PTO (Power Take-off) Knob/Lever H Ignition Switch

B Choke Control I Brake Pedal

C Parking Brake Button J Drive Pedal

D Shift Lever K Cruise Control Button

E Cup Holder (if equipped) L Seat Adjustment Lever

F Systems Indicator Monitor/Hour Meter M Deck Lift Lever

G Throttle Control Lever

I

B

A

H

C

E

M

K

J

L

G

F

D

NOTE:

Steering Wheel not shown for clarity.

A

Models with

PTO lever

11

Throttle Control Lever

The throttle control lever is

located on the right side of the

tractor’s dash panel. This lever

controls the speed of the engine.

When set in a given position, the

throttle will maintain a uniform

engine speed.

IMPORTANT:

When operating the

tractor with the cutting deck

engaged, be certain that the

throttle lever is always in the

FAST (rabbit) position.

Choke Control

The choke control can be found

on the left side of the dash panel

and is activated by pulling the

knob outward. Activating the

choke control closes the choke

plate on the carburetor and aids

in starting the engine. Refer to page 13 of this manual

for detailed starting instructions.

Brake Pedal

The brake pedal is located on the

right front side of the tractor

above the drive pedal along the

running board. The brake pedal

can be used for sudden stops or

setting the parking brake.

NOTE: Brake pedal must be fully depressed to activate

the safety interlock switch when starting the tractor

.

Ignition Switch

To start the engine, insert the key

into the ignition switch and turn

clockwise to the START position.

Release the key into the ON

position once engine has fired.

Refer to page 13 for detailed

starting instructions.

The ignition switch is also used to

operate the tractor’s headlights.

Refer to page 15 for detailed

instructions.

Cup Holder (if equipped)

The cup holder is located on the fender to the left of the

seat, just to the rear of the parking brake lever.

Drive Pedal

The drive pedal is located below

the brake pedal on the right front

side of the tractor along the

running board. Depress the drive

pedal with your right foot when

the tractor shift lever is in either

FORWARD or REVERSE to

cause the tractor to move.

Ground speed is also controlled

with the drive pedal. The further

down the pedal is depressed, the faster the tractor will

travel. The pedal will return to its original position when

it is not depressed.

IMPORTANT:

Always set the parking brake when

leaving the tractor unattended..

PTO (Power Take-off) Lever

For models with PTO

lever:Tthis lever is located

on the left side of the

dashboard next to the

steering wheel. Move the PTO lever forward to engage

power to the cutting deck or other (separately available)

attachments; move the PTO lever backward (toward

the rear of the tractor) to disengage power to the

attachments.

Electric PTO (Power Take-off) Knob

For models with PTO knob: To

engage the power to the cutting

deck or other (separately

available) attachments, pull

outward on the PTO knob. Push

the PTO knob inward to

disengage the power to the

cutting deck.

NOTE: The PTO knob must be in the disengaged

(OFF) position when starting the engine, when traveling

in reverse and if the operator leaves the seat.

Shift Lever

The shift lever is located on the

front of the fender between the

operator’s legs and has four

positions, FORWARD—HI,

FORWARD—LO, NEUTRAL and

REVERSE. The brake pedal

must be depressed and the

tractor must not be in motion

when moving the shift lever. Always bring the tractor to

a complete stop prior to moving the shift lever from

FORWARD—HI to FORWARD—LO or vice-versa.

IMPORTANT:

Never force the shift lever. Doing so may

result in serious damage to the tractor’s transmission.

WARNING:

Never leave a running machine

unattended. Always disengage PTO, move

shift lever into neutral position, set parking

brake, stop engine and remove key to prevent

unintended starting.

Slow

Fast

Off

Start

On

On/Lights

R

FL

Shift Knob

FH

12

Seat Adjustment Lever

To adjust the seat forward or backward, slide the seat

adjustment lever to the left and reposition the seat to

the desired position. Once a comfortable position is

found, release the seat adjustment lever to lock the

seat in place. Refer to Seat Adjustment on page 17 of

this manual for more detailed instructions.

Deck Lift Lever

Found on your tractor’s right fender, the deck lift lever is

used to change the height of the cutting deck. To use,

move the lever to the left, then place in the notch best

suited for your application.

Parking Brake Button

To set the parking brake, fully

depress the brake pedal and

push the parking brake button in.

Hold the button in while taking

your foot off the brake pedal.

Both the parking button and the

brake pedal will then stay

depressed. To release the

parking brake, depress the brake

pedal slightly. The parking brake

button will then return to its

original position.

NOTE: The parking brake must be set if the operator

leaves the seat with the engine running or the engine

will automatically shut off.

IMPORTANT:

Always set the parking brake when

leaving the tractor unattended.

Cruise Control Button

The cruise control button is

located on the tractor dash panel

to the left of the ignition switch.

Push the cruise control button

while traveling forward at a

desired speed. While holding the

button in, release pressure from

the drive pedal. This will engage

the cruise control and allow the

tractor to remain at that speed

without applying pressure to the

drive pedal. Depress the brake pedal or the drive pedal

to deactivate cruise control. Refer to Operations section

in this manual for detailed instructions.

NOTE: Cruise control can not be engaged at the

tractor’s fastest ground speed. If the operator should

attempt to do so, the tractor will automatically

decelerate to the fastest optimal mowing ground speed.

Systems Indicator Monitor

Your tractor is equipped with four indicator lights and an

ammeter. See Figure 7. The ammeter is locatde on the

left side of the dash panel.

Figure 7

The ammeter measures the electrical output of the

engine’s charging system. Under normal operating

conditions, with the engine at full throttle, the ammeter’s

needle should measure a positive charge.

If the brake light or PTO light illuminates when

attempting to start the unit, proceed as follows:

It is normal for the oil light and the battery light to

illuminate while the engine is cranking, but if either

illuminates while the engine is running, follow the steps

below as per indication:

P

Indication Remedy

Brake light on Engage the parking brake.

PTO light on Move PTO knob/lever to the

disengaged(OFF) position.

Indication Remedy

Oil light on Stop the tractor immediately

and check thecrankcase oil

level as instructed in the

engine manual. Add oil as

required.

Oil

Brake

PTO

AMPS

Ammeter

13

SECTION 5: OPERATING YOUR GARDEN TRACTOR

Safety Interlock Switches

This tractor is equipped with a safety interlock system

for the protection of the operator. If the interlock system

should ever malfunction, do not operate the tractor.

Contact an authorized service dealer. The safety

interlock system prevents the engine from cranking or

starting unless the parking brake is engaged, and the

PTO knob/lever is in the disengaged (OFF) position.

The engine will automatically shut off if

1. the operator leaves the seat before engaging the

parking brake;

2. the operator leaves the tractor’s seat with the PTO

knob/lever in the engaged (ON) position,

regardless of whether the parking brake is

engaged; and

3. the PTO knob/lever is moved to engaged (ON)

position with the shift lever in position for reverse

travel.

Setting the Cutting Height

• Select the height position of the cutting deck by

placing the deck lift lever in any of the six different

cutting height notches on the right side of the

fender.

• Adjust the deck wheels so that they are between ¼-

inch and ½-inch above the ground when the tractor

is on a smooth, flat surface such as a driveway.

NOTE: The deck wheels are an anti-scalp feature of the

deck and are not designed to support the weight of the

cutting deck.

Refer to Leveling the Deck on page 16 of this manual

for more detailed instructions regarding various deck

adjustments.

Starting the Engine

NOTE: Refer to page 7 of this manual for gasoline and

oil fill-up instructions.

• Insert the tractor key into the ignition switch.

• Place the PTO knob/lever in the disengaged (OFF)

position.

• Engage the tractor’s parking brake.

• Place the throttle control in the FAST (rabbit)

position.

• Pull the choke control outward.

• Turn the ignition key clockwise to the START

position. After the engine starts, release the key. It

will return to the ON position.

IMPORTANT:

Do not hold the key in the START position

for longer than ten seconds at a time. Doing so may

cause damage to your engine’s electric starter.

• After the engine starts, deactivate the choke control

and place the throttle control in the FAST position.

NOTE: Do not leave the choke control on while

operating the tractor. Doing so will result in a "rich" fuel

mixture and cause the engine to run poorly.

Stopping the Engine

• If the blades are engaged, place the PTO knob/

lever in the disengaged (OFF) position.

• Turn the ignition key counterclockwise to the OFF

position.

• Remove the key from the ignition switch to prevent

unintended starting.

WARNING:

Do not operate the tractor if the

interlock system is malfunctioning. This system

was designed for your safety and protection.

AVOID SERIOUS INJURY OR DEATH

• GO UP AND DOWN SLOPES, NOT ACROSS.

• AVOID SUDDEN TURNS.

• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.

• IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK

DOWNHILL SLOWLY.

• DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.

• NEVER CARRY CHILDREN, EVEN WITH BLADES OFF.

• LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.

• KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN

PLACE AND WORKING.

• REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADE(S).

• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.

• BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE PLAC-

ING HANDS OR FEET NEAR BLADE(S).

• BEFORE LEAVING OPERATOR’S POSITION, DISENGAGE

BLADE(S), PLACE THE SHIFT LEVER IN NEUTRAL, ENGAGE

BRAKE LOCK, SHUT ENGINE OFF AND REMOVE KEY.

READ OPERATOR’S MANUAL

WARNING

WARNING:

Keep hands and feet away from

the discharge opening of the cutting deck.

WARNING:

If you strike a foreign object,

stop the engine, disconnect the spark plug

wire(s) and ground against the engine.

Thoroughly inspect the machine for any

damage. Repair the damage before restarting

and operating.

14

Driving The Tractor

IMPORTANT:

Avoid sudden starts, ex-cessive speed

and sudden stops.

• Depress the brake pedal to release the parking

brake and let the pedal up. Move the throttle lever

into the FAST (rabbit) position.

IMPORTANT:

Do not use the shift lever to change the

direction of travel when the tractor is in motion. Always

use the brake pedal to bring the tractor to a complete

stop before shifting.

• To move forward, place the shift lever in the

FORWARD position, then slowly depress the drive

pedal until the desired speed is achieved.

• To move in reverse, place the shift lever in the

REVERSE position, check that the area behind is

clear then slowly depress the drive pedal.

Engaging the Parking Brake

To engage the parking brake:

• Fully depress the brake pedal and hold it there

while gently pushing the parking brake button

inward.

• Hold the parking brake button in while removing

your foot from the brake pedal.

• Once engaged, the parking brake button and the

brake pedal will lock in the “down” position.

To disengage the parking brake:

• Slightly depress the brake pedal.

NOTE: The parking brake must be engaged if the

operator leaves the seat with the engine running or the

engine will automatically shut off.

Operating the Headlights

To turn the tractor’s headlights on:

• Start the engine following the instructions earlier in

this section.

• Turn the key one notch counterclockwise into the

On/Lights position of the ignition switch. Refer to

figure on page 11.

To turn the tractor’s headlights off:

• Turn the key either into the On position (to leave the

engine running) or the Off position (to shut the

engine off).

NOTE: Never move the key into the Start position while

the engine is running. Doing so may cause damage to

your engine’s electric starter.

Driving On Slopes

Refer to SLOPE GAUGE on page 6 to help determine

slopes where you may operate the tractor safely.

• Mow up and down slopes, never across.

• Exercise extreme caution when changing direction

on slopes.

• Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could overturn the

machine. Tall grass can hide obstacles.

• Avoid turns when driving on a slope. If a turn must

be made, turn downwards on the slope. Turning

upwards on a slope greatly increases the chance of

a roll over.

• Avoid stopping when driving up a slope. If it is

necessary to stop while driving up a slope, start up

smoothly and carefully to reduce the possibility of

flipping the tractor over backward.

Setting the Cruise Control

NOTE: The cruise control feature should only be

utilized while traveling in the forward direction.

Engaging Cruise Control

• Place the shift lever in the FORWARD position,

then slowly depress the drive pedal until the desired

speed is achieved.

• Lightly depress the cruise control button.

• While continuing to hold the cruise button in, lift

your foot from the drive pedal (you should feel the

cruise latch engage).

• Once engaged, the cruise control button and the

drive pedal will lock in the “down” position, and the

tractor will maintain the same forward speed.

NOTE: Cruise control cannot be engaged at the

tractor’s fastest ground speed. If the operator should

attempt to do so, the tractor will automatically

decelerate to the fastest optimal mowing ground speed.

Disengaging Cruise Control

Choose one of the following two methods:

1. Depress the brake pedal to disengage the cruise

control and stop the tractor.

2. Lightly depress the drive pedal.

Changing to Reverse when Cruise Control is Engaged

• Depress the brake pedal to disengage the cruise

control and bring the tractor to a complete stop.

WARNING:

Do not leave the seat of the

tractor without first placing the PTO knob/lever

in the disengaged (OFF) position, depressing

the brake pedal and engaging the parking

brake. If leaving the tractor unattended, also

turn the ignition key off and remove the key.

WARNING:

Do not mow on inclines with a

slope in excess of 15 degrees (a rise of

approximately 2-1/2 feet every 10 feet). The

tractor could overturn and cause serious injury.

15

• Place the shift lever in the REVERSE position, look

to the rear to ensure the path is empty, and depress

the drive pedal.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to the

left, then place it in the notch best suited for your

application. Refer to Setting The Cutting Height earlier in

this section.

Engaging the PTO

Engaging the PTO transfers power to the cutting deck

or other (separately available) attachments. To engage

the PTO, proceed as follows:

• Move the throttle control lever to the FAST (rabbit)

position.

•On models with PTO lever: Pull the PTO lever

outward into the engaged (ON) position.

• Keep the throttle lever in the FAST (rabbit) position

for the most efficient use of the cutting deck or other

(separately available) attachments

NOTE: The operator must remain on the tractor seat at

all times of operation. If the operator leaves the seat

without moving the PTO lever into the disengaged

(OFF) position, the tractor’s engine will automatically

shut off, regardless of whether the parking brake is

engaged or not

•On units equipped with electric PTO, pull the

PTO knob outward to engage power to the cutting

deck. Push the PTO knob inward to disengage

power to the cutting deck

Figure 8

IMPORTANT:

The PTO clutch will automatically shut off

if the PTO is engaged with the shift lever in position for

reverse travel. Refer to Safety Interlock Switches on

page 13.

Mowing

The following information will be helpful when using the

cutting deck with your tractor.

•Do not mow at high ground speed, especially if a

mulch kit or grass collector is installed.

• For best results it is recommended that the first two

laps be cut with the discharge thrown towards the

center. After the first two laps, reverse the direction

to throw the discharge to the outside for the

balance of cutting. This will give a better

appearance to the lawn.

• Do not cut the grass too short. Short grass invites

weed growth and yellows quickly in dry weather.

WARNING:

To help avoid blade contact or a

thrown object injury, keep bystanders, helpers,

children and pets at least 75 feet from the

machine while it is in operation. Stop machine if

anyone enters the area.

WARNING:

Plan your mowing pattern to

avoid discharge of materials toward roads,

sidewalks, bystanders and the like. Also, avoid

discharging material against a wall or

obstruction which may cause discharged

material to ricochet back toward the operator.

ON

OFF

Front View Pull Out Push In

16

SECTION 6: MAKING ADJUSTMENTS

Parking Brake

Adjust the brake if

1. the tractor does not stop completely when the

brake pedal is completely depressed; or

2. the tractor’s rear wheels roll even with the parking

brake applied.

Locate the brake disc on right of the transmission in the

rear of the tractor and adjust as follows:

• Looking at the transmission from the right side of

the tractor, locate the compression spring and

brake disc.

• Loosen, but do not remove, the hex nut found on

the right side of the brake assembly.

• Using a feeler gauge, set the gap between the

brake disc and the brake puck at .011".

• Re-tighten the hex nut loosened earlier.

Seat

• To adjust the position of the seat, move the seat

adjustment lever to the left and slide the seat

forward or rearward. Make sure seat is locked into

position before operating the tractor.

Steering

Adjust the steering drag links if

1. the tractor turns tighter in one direction than the

other; or

2. while the ball joints are being replaced.

Adjust the drag links so that equal lengths are threaded

into the ball joints on the left and the right respectively.

• Loosen the jam nut found on the drag link at the

rear of the ball joint. See Figure 9.

Figure 9

• Remove the hex nut and lock washer on the top of

ball joint. See Figure 9.

• Thread the ball joint toward the jam nut to shorten

the drag link. Thread the ball joint away from the

jam nut to lengthen the drag link.

• Replace hex nut and lock washer and retighten the

jam nut after proper adjustment is achieved.

NOTE: Threading the ball joints too far onto the drag

links will cause the front tires to "toe-in" too far. Proper

toe-in is between 1/16" and 5/16".

Front tire toe-in can be measured as follows:

• Place the steering wheel in position for straight

ahead travel.

• In front of the axle, measure the distance

horizontally from the inside of the left rim to the

inside of the right rim. Note the distance.

• Behind the axle, measure the distance horizontally

from the inside of the left rim to the inside of the

right rim. Note the distance.

• The measurement taken in front of the axle should

be between 1/16" and 5/16" less than the

measurement taken behind the axle. Adjust if

necessary.

Leveling the Deck

NOTE: Check the tractor’s tire pressure before

performing any deck leveling adjustments. Refer to

page 22 for information regarding tire pressure.

Front To Rear

The front of the cutting deck is supported by a stabilizer

bar that can adjusted to level the deck from front to rear.

WARNING:

Never attempt to make any

adjustments while the engine is running,

except where specified in the manual.

WARNING:

Disconnect the spark plug

wire(s) and ground against the engine before

performing any adjustments, repairs or

maintenance.

WARNING:

Never attempt to adjust the

brakes while the engine is running. Always

disengage PTO, move shift lever into neutral

position, stop engine and remove key to

prevent unintended starting.

WARNING:

Before operating this machine,

make sure the seat is engaged in the seat stop,

stand behind the machine and pull back on

seat until fully engaged into stop.

Drag Link

Ball Joint

Axle

Pivot Bar

Hex Nut and

Jam Nut

Lock Washer

17

The front of the deck should be between 1/4-inch and

3/8-inch lower than the rear of the deck. Adjust if

necessary as follows:

• With the tractor parked on a firm, level surface,

place the deck lift lever in the top notch (highest

position) and rotate the blade nearest the discharge

chute so that it is parallel with the tractor.

• Measure the distance from front of the blade tip to

the ground and rear of the blade tip to the ground.

• The first measurement taken should be between

1/4" and 3/8" less than the second measurement.

Determine the approximate distance necessary for

proper adjustment and proceed to the next step.

• Loosen the two jam nuts on the rear side of the

deck stabilizer bracket. See Figure 10A.

• Locate the two lock nuts on the opposite side of the

stabilizer bracket. See Figure 10A. Tighten the lock

nuts to raise the front of the deck; loosen the lock

nuts to lower the front of the deck.

• Retighten the two jam nuts loosened earlier when

proper adjustment is achieved.

Side to Side

If the cutting deck appears to be mowing unevenly, a

side to side adjustment can be performed. Adjust if

necessary as follows:

• With the tractor parked on a firm, level surface,

place the deck lift lever in the top notch (highest

position) and rotate both blades so that they are

perpendicular with the tractor.

• Measure the distance from the outside of the left

blade tip to the ground and the distance from the

outside of the right blade tip to the ground. Both

measurements taken should be equal. If they’re

not, proceed to the next step.

• Loosen, but do NOT remove, the hex cap screw on

the left deck hanger bracket. See Figure 10B.

• Balance the deck by using a wrench to turn the

adjustment gear (found immediately behind the hex

cap screw just loosened) clockwise/up or

counterclockwise/down.

• The deck is properly balanced when both blade tip

measurements, taken earlier, are equal.

• Retighten hex cap screw on the left deck hanger

bracket when proper adjustment is achieved.

Figure 10

Deck Roller Height

(Model 808K only)

To adjust the height of the rollers on the rear of the

mowing deck, proceed as follows:

• Place the deck lift lever in the bottom notch (lowest

position).

• Remove the clevis pins and hairpin clips from the

deck roller brackets on the left and right sides of the

cutting deck. See Figure 11.

• Position the deck roller brackets up or down

through the slots on the rear of the deck until

desired position is reached. Re-attach with clevis

pins and hairpin clips just removed. See Figure 11.

NOTE: Be certain that the left roller bracket and the

right roller bracket are set in the same position

Figure 11

Jam

Deck

Stabilizer

Bracket

Nuts

Lock

Nuts

Deck

A

Hex Cap Screw

Adjustment Gear

B

Hairpin

Clevis

Deck Roller

Clip

Bracket

Pin

18

SECTION 7: MAINTAINING YOUR GARDEN TRACTOR

Engine

Refer to the engine manual for engine maintenance

instructions.

• Check engine oil level before each use as

instructed in the engine manual.

Figure 12

Changing Engine Oil

NOTE: Depending on the engine model found on your

tractor, it may be necessary to remove the tractor’s side

panel in order to replace the oil filter (if so equipped).

• Unscrew oil fill cap and remove dipstick from the oil

fill tube. See Figure 12.

• Pop open the protective cap on the end of the oil

drain valve to expose the drain port. See Figure 12.

• Push the oil drain hose (packed with this manual)

onto the oil drain port. Route the opposite end of

the hose into an appropriate oil collection container

with a capacity great enough to collect the used oil

(approximately 64 oz.).

• Push the oil drain valve in slightly, then rotate

counterclockwise and pull outward to begin

draining oil. See Figure 12.

• Service the oil filter (if so equipped) as instructed

in the engine manual.

• Perform the above steps in the opposite order after

oil has finished draining.

• Refill the engine with new motor oil.

IMPORTANT:

Refer to the engine manual for details

about quantity and proper weight of motor oil.

Air Cleaner

• Service the pre-cleaner, if so equipped, and

cartridge/air cleaner element as instructed in the

engine manual.

Spark Plugs

• Clean the spark plugs and reset the gap once a

season. Spark plug replacement is recommended

at the start of each mowing season. Refer to the

engine manual for correct plug type and gap

specifications.

Cleaning Engine and Deck

• Promptly wipe off any fuel or oil spilled on the

machine.

• Do not allow grass, leaves, and dirt to accumulate

around the cooling fins of the engine or on any

other part of the machine, especially the pulleys

and other moving parts.

IMPORTANT:

The use of a pressure washer to clean

your tractor is not recommended. Direct water pressure

on electrical components and the engine could reduce

life of the tractor and its serviceability.

Lubrication

Engine

Lubricate the engine with motor oil as instructed in the

Briggs & Stratton Operator/Owner Manual packed with

your unit.

Pivot Points & Linkage

Lubricate all the pivot points on the drive system,

parking brake and lift linkage at least once a season

with light oil.

Front Wheels

Each end of the tractor’s front pivot bar is equipped with

a grease fitting. Lubricate with a grease gun after every

25 hours of tractor operation.

WARNING:

Before performing any

maintenance or repairs, disengage PTO, move

shift lever into neutral position, set parking

brake, stop engine and remove key to prevent

unintended starting.

Protective Cap

Oil Drain Hose

Drain Port

Oil Fill Cap

Oil Fill Tube

WARNING:

Before lubricating, repairing, or

inspecting, always disengage PTO, move shift

lever into neutral position, set parking brake,

stop engine and remove key to prevent

unintended starting.

19

SECTION 8: SERVICE

Cutting Deck Removal

To remove the cutting deck, proceed as follows:

• Place the PTO knob/lever in the disengaged (OFF)

position and engage the parking brake.

• Lower the deck by moving the deck lift lever into the

bottom notch on the right fender.

• Remove the PTO belt from around the electric PTO

clutch. Refer to Figure 14.

• Looking at the cutting deck from the left side of the

tractor, locate the deck support pin on the rear left

side of the deck.

• Pull the deck support pin outward to release the

deck from the deck lift arm. See Figure 13.

Figure 13

• Rotate the pin slightly toward the rear of the tractor

and release the pin into the hole provided.

• Repeat the above steps on the tractor’s right side.

• Move the deck lift lever into the top notch on the

right fender to raise the deck lift arms up and out of

the way.

• Gently slide the cutting deck toward the front of the

tractor allowing the hooks on the deck to release

themselves from the deck stabilizer rod.

• Gently slide the cutting deck (from the right side)

out from underneath the tractor.

Changing the Deck Belt(s)

WARNING:

Be sure to shut the engine off,

remove ignition key, disconnect the spark

plug wire(s) and ground against the engine to

prevent unintended starting before removing

the belt(s).

All belts on your tractor are subject to wear and should

be replaced if any signs of wear are present.

IMPORTANT:

The V-belts found on your tractor are

specially designed to engage and disengage safely. A

substitute (non-OEM) V-belt can be dangerous by not

disengaging completely. For a proper working machine,

use factory approved belts.

Figure 14

Support Pin

Left Hand

Double Pulley

Right Hand Pulley

Deck Idler Pulley

(beneath belt guard)

Deck Belt (Bottom)

PTO Belt (Top)

Engine Pulley

Center Pulley

PTO Idler Bracket

(mounted on tractor)

Model 808H

Oil

Drain

Valve

20

To change or replace the deck belts on your tractor,

proceed as follows:

• Lower the deck by moving the deck lift lever into the

bottom notch on the right fender.

• Remove the belt guards by removing the self-

tapping screws that fasten them to the deck.

•Model 808H only: Grasp the PTO idler bracket and

pivot it toward the discharge chute to relieve

tension on the PTO belt.

•Model 808H only: Remove the PTO belt from the

engine pulley and from around the PTO idler

pulleys.

•Model 808K only: Remove the PTO belt from the

electric PTO clutch and from around the PTO idler

pulley, if present.

• Grasp the deck idler pulley and pivot it toward the

left side of the deck to relieve tension on the belt.

• Remove the belt from around all spindle pulleys,

and deck idler pulley(s).

• According to your tractor model, route the new belts

as shown in Figure 14 or Figure 15.

• Remount the belt guards removed earlier.

Figure 15

Changing the Transmission Drive Belt

All belts on your tractor are subject to wear and should

be replaced if any signs of damage are observed.

NOTE: It is recommended that both drive belts be

replaced at the same time.

IMPORTANT:

The V-belts found on your tractor are

specially designed to engage and disengage safely. A

substitute (non-OEM) V-belt can be dangerous by not

disengaging completely. For a proper working machine,

use factory approved belts.

To change or replace the drive belt on your tractor,

proceed as follows:

• Remove the cutting deck as instructed earlier.

• After disconnecting the battery cables, remove the

battery and battery tray from beneath the seat.

IMPORTANT:

When removing the battery, disconnect

the negative (black) wire from its terminal first, followed

by the positive (red) wire. Re-install in reverse order.

Upper Drive Belt

• Locate the transmission idler pulley on the upper

drive belt by looking through the battery tray

opening. See Figure 16.

• Grasp the bracket and pivot the transmission idler

pulley toward the rear of the tractor to release

tension on the upper drive belt.

• Remove the belt from around the transmission idler

pulley.

• Remove the upper drive belt from around the

transmission pulley and the variable-speed pulley.

Left Hand

Pulley

Right Hand

Pulley

Center Pulley

Electric

Deck / PTO belt

Deck Idler Pulleys

PTO Clutch

Model 808K

WARNING:

Be sure to shut the engine off,

remove ignition key, disconnect the spark plug

wire(s) and ground against the engine to

prevent unintended starting before removing

the belt(s).

21

Figure 16

NOTE: Slowly rotate the pulley counter-clockwise to roll

the belt off it.

• Remove the upper drive belt by pulling it up through

the battery tray opening.

• Reroute the new upper drive belt as shown in

Figure 16.

Lower Drive Belt

NOTE: Proper removal of the lower drive belt requires

the removal of several tractor components. Read

through the following procedure prior to attempting it;

determine if you can successfully complete it.

Otherwise, see an authorized service dealer for the job.

IMPORTANT:

Note the routing of the lower drive belt

around both the pulleys and the belt keepers before

performing the following steps.

• Locate the variable-speed pulley through the

battery tray opening. See Figure 16.

• Remove the variable-speed pulley by loosening the

hex bolt that secures it to the transmission. Use a

second wrench to hold the hex nut on the bottom

side of the pulley.

• Slide the belt off the variable-speed pulley as you

lift the pulley up and out through the battery tray

opening.

• Remove rear idler pulley from the double- idler

bracket while loosening the belt from around both

the rear and the front idler pulleys. See Figure 16.

•Model 808H only: Remove the hex bolt from the

center of the engine pulley and gently lower it off

the engine crankshaft. Be careful not to lose any

washers or spacers which may be on top of the

engine pulley.

•Model 808K only: Remove the hex bolt from the

center of the electric PTO clutch and gently lower it

off the engine crankshaft. Be careful not to lose any

washers or which may be found on top of the PTO

clutch.

IMPORTANT:

When remounting the PTO clutch, torque

the center hex bolt to between 38 foot-pounds and 50

foot-pounds.

• Remove the drive belt by feeding it from both ends

toward the front idler pulley on the double-idler

bracket. See figures above.

• Reassemble by following the above steps in

reverse order.

• Reroute the new belt around the pulleys, belt

keepers and keeper pins exactly as the old one was

routed. Refer to Figure 16.

The drive pedal is properly adjusted when the hole

found in the double-idler bracket has approximately

1-3/8" of travel with 10 pounds of pressure applied to

the drive pedal. See Figure 17.

Transmission Idler Pulley

Transmission Pulley

Engine Pulley

Front of Tractor

Rear Idler Pulley

Front Idler Pulley

Variable-speed

Pulley

Drive Belt (Lower)

Drive Belt (Upper)

22

Figure 17

Adjust the drive pedal after replacing the drive belts on

your tractor, if necessary, as follows:

• Locate the speed control assembly on the

underside of the steering support bracket. See

Figure 18.

Figure 18

• Remove both hairpin clips from the pin which is

fastened to the speed control assembly (be careful

not to lose the small flat washers found on the pin).

See Figure 18.

• Remove the drive pedal return spring.

• Using two 9/16" wrenches, remove the pin from the

speed control assembly. See Figure 18.

• Thread the idler adjustment rod inward or outward

to lengthen or shorten the travel of the double-idler

bracket until proper adjustment is achieved.

• Reassemble by following the above steps in

reverse order.

Tires

Refer to the tire sidewall for exact tire manufacturer’s

recommended or maximum psi. Do not overinflate.

Uneven tire pressure could cause the cutting deck to

mow unevenly.

Cutting Blades

• Periodically inspect the blade adapter and/or

spindle for cracks or damage, especially if you

strike a foreign object. Replace immediately if

damaged

.

The blades may be removed as follows:

• Remove the deck from beneath the tractor, (refer to

Cutting Deck Removal on page 19) then gently flip the

deck over to expose its underside.

• Place a block of wood between the center deck

housing baffle and the cutting blade to act as a

stabilizer. See Figure 19.

Figure 19

• Use a 15/16" wrench to remove the hex flange nut

that secures the blade to the spindle assembly. See

Figure 19.

• To properly sharpen the cutting blades, remove

equal amounts of metal from both ends of the

blades along the cutting edges, parallel to the

trailing edge, at a 25° to 30° angle. See Figure 20.

IMPORTANT:

If the cutting edge of the blade has already

been sharpened to within 5/8" of the wind wing radius,

or if any metal separation is present, replace the

blades. See Figure 20.

WARNING:

Never exceed the maximum

inflation pressure shown on the tire sidewall.

Front of Tractor

NOTE:

View shown from above tractor.

Double-idler Bracket

Idler

Adjuster Rod

Hole

1-3/8”

Speed Control

Assembly

Hairpin

Clips

Idler Adj. Rod

Pin

Drive Pedal

Return Spring

Place wrenches here

Neutral

Return

Bracket

WARNING:

Be sure to shut the engine off,

remove ignition key, disconnect the spark plug

wire(s) and ground against the engine to

prevent unintended starting before removing

the cutting blade(s) for sharpening or

replacement. Protect your hands by using

heavy gloves or a rag to grasp the cutting

blade.

Spindle Assembly

Hex Flange Nut

Wood Block

23

• Grind each cutting blade edge equally to maintain

proper blade balance.

• Test the blade by balancing it on a round shaft

screwdriver. Grind metal from the heavy side until it

balances evenly.

• When replacing the blade, be sure to install the

blade with the side of the blade marked ‘‘Bottom’’

(or with a part number stamped in it) facing the

ground when the mower is in the operating position.

IMPORTANT:

Use a torque wrench to tighten the blade

spindle hex flange nut to between 70 foot-pounds and

90 foot-pounds.

Figure 20

Fuses

Two fuses are installed in your tractor’s wiring harness

to protect the tractor’s electrical system from damage

caused by excessive amperage.

• If the electrical system does not function, or your

tractor’s engine will not crank, first check to be

certain that the fuse has not blown. One fuse is

located under the hood mounted behind the top of

the dash panel on the support bar. The other can

be found under the seat mounted to the inside of

the tractor frame next to the battery tray. Pull the

fuse out and inspect it to determine if it is good or

blown. Replace if necessary.

IMPORTANT:

Always use a fuse with the same

amperage capacity for replacement.

Battery

The battery is sealed and is maintenance-free. Acid

levels cannot be checked.

• Always keep the battery cables and terminals clean

and free of corrosive build-up.

• After cleaning the battery and terminals, apply a

light coat of petroleum jelly or grease to both

terminals.

IMPORTANT:

Always keep the rubber boot positioned

over the positive terminal to prevent shorting.

IMPORTANT:

If removing the battery for any reason,

disconnect the negative (black) wire from its terminal

first, followed by the positive (red) wire. When re-

installing the battery, always connect the positive (red)

wire its terminal first, followed by the negative (black)

wire. Be certain that the wires are connected to the

correct terminals; reversing them could change polarity

and damage the engine’s alternating system.

Charging

If the tractor has not been put into use for an extended

period of time, charge the battery with an automotive-

type 12-volt charger for a minimum one hour at 6 amps.

WARNING:

A poorly balanced blade will

cause excessive vibration, may damage the

tractor and cause personal injury.

WARNING:

Before servicing, repairing, or

inspecting, always disengage PTO, move shift

lever into neutral position, set parking brake,

stop engine and remove key to prevent

unintended starting.

Blade Separation

Worn Blade Edge

Wind Wing

Sharpen Edge Evenly

5/8"

minimum

WARNING:

Batteries give off an explosive

gas while charging. Charge battery in a well

ventilated area and keep away from an open

flame or pilot light as on a water heater, space

heater, furnace, clothes dryer or other gas

appliances.

24

SECTION 9: OFF-SEASON STORAGE

Clean and lubricate the tractor as instructed on page 18

of this manual before storing for an extended period.

Follow the instructions in the service, storage &

specifications section of the engine manual for proper

engine care prior to storing your tractor.

SECTION 10: ATTACHMENTS & ACCESSORIES

The following attachments and accessories are compatible for tractor models 808H & 808K. See the retailer from

which you purchased your tractor or phone (866) 840-6483 for information regarding price and availability.

† OEM-190-824 is required for use of this attachment. OEM-190-608 cannot be used in its place.

WARNING:

Drain fuel only into an approved

container outdoors, away from an open flame.

Allow engine to cool. Extinguish cigarettes,

cigars, pipes, and other sources of ignition prior

to draining fuel.

WARNING:

Never store the machine or fuel

container indoors where there is an open

flame, spark or pilot light such as on water

heater, furnace, clothes dryer or other gas

appliance.

MODEL DESCRIPTION

OEM-190-118 Mulch Kit (For 46-inch Decks Only)

OEM-190-603 FastAttach™ Grille Guard (mounts on front of tractor)

OEM-190-604 FastAttach™ Yard-Mate™ Storage Container/Toolbox (mounts on rear of tractor)

OEM-190-607 FastAttach™ Deluxe Tractor Sunshade

OEM-190-608 FastAttach™ Sleeve Hitch, Manual Lift

OEM-190-181 FastAttach™ Triple Bagger Grass Collector (For 46-inch Decks Only)

OEM-190-822 FastAttach™ 46-inch Front Dozer Blade

OEM-190-823 42-inch Two-stage Snowthrower

OEM-190-824 Sleeve Hitch with Electric Lift

OEM-190-841 Mulch Kit (For 54-inch Decks Only)

OEM-190-842 FastAttach™ Triple Bagger Grass Collector (For 54-inch Decks Only)

SLEEVE HITCH ATTACHMENTS (For use with OEM-190-824 or OEM-190-608 )

OEM-190-825 30-inch Hydraulic Tiller†

OEM-190-984 Row Crop Cultivator

OEM-190-980 Single-disc Harrow

OEM-190-978 10-inch Mulboard Plow

OEM-190-804 42-inch Heavy Duty Rear Blade

25

SECTION 11: TROUBLESHOOTING

Trouble Possible Cause(s) Corrective Action

Engine fails to start PTO knob/lever engaged.

Parking brake not engaged.

Spark plug wire(s) disconnected.

Throttle control lever not in correct

starting position.

Choke not activated

Fuel tank empty, or stale fuel.

Blocked fuel line.

Faulty spark plug.

Engine flooded.

Place PTO knob/lever in disengaged (OFF) position.

Engage parking brake.

Connect wire(s) to spark plug.

Place throttle lever to FAST position.

Pull out the CHOKE control (if so equipped).

Fill tank with clean, fresh (less than 30 days old) gas.

Clean fuel line or replace fuel filter, if so equipped.

Clean, adjust gap or replace plug.

Crank engine with throttle in FAST position.

Engine runs erratic Unit running with CHOKE applied.

Spark plug wire(s) loose.

Blocked fuel line or stale fuel.

Vent in gas cap plugged.

Water or dirt in fuel system.

Dirty air cleaner.

Push CHOKE control (if so equipped) in.

Connect and tighten spark plug wire(s).

Clean fuel line; fill tank with clean, fresh (less than 30

days old) gasoline. Replace fuel filter, if so equipped.

Clear vent or replace cap if damaged.

Drain fuel tank. Refill with clean, fresh (less than 30

days old) gasoline.

Replace air cleaner cartridge/element or clean pre-

cleaner, if so equipped.

Engine overheats Engine oil level low.

Air flow restricted.

Fill crankcase with proper capacity and weight of oil.

Clean grass clippings and debris from around the

engine’s cooling fins and blower housing.

Engine hesitates at high RPM Spark plug(s) gap too close. Remove spark plug(s) and reset the gap to .030” .

Idles poorly Spark plug(s) fouled, faulty or gap too

wide.

Dirty air cleaner.

Replace spark plug(s). Set plug(s) gap to .030” .

Replace air cleaner cartridge/element or clean pre-

cleaner, if so equipped.

Excessive vibration Cutting blade loose or unbalanced.

Damaged or bent cutting blade.

Tighten blade and spindle. Balance blade.

Replace blade.

Mower will not mulch grass Engine speed too low.

Wet grass.

Excessively high grass.

Dull blade.

Place throttle in FAST (rabbit) position.

Do not mow when grass is wet; wait until later to cut.

Mow once at a high cutting height, then mow again at

desired height or make a narrower cutting swath.

Sharpen or replace blade.

Uneven cut Deck not balanced properly.

Dull blade.

Uneven tire pressure.

Perform side-to-side deck adjustment.

Sharpen or replace blade.

Check tire pressure in all four tires.

26

SECTION 12: PARTS LIST FOR MODELS 808H & 808K

97

11

(for choke)

13

4

12

6

9

22

18

19

20

8

10

14

10

5

10

5

16

15

1

17

5

24

3

2

21

23

27

Models 808H & 808K

REF.

NO.

PART

NO. DESCRIPTION

1 710-0227 Self-tapping Screw, #8-18 x .5

2 710-0599 Self-tapping Screw, 1/4-20 x .5

3 710-0726 AB Screw, 5/16-12 x .75

4 710-1237 Screw, #10-32 x .625

5 710-1314A Socket Cap Screw, 5/16-18 x .625

6 710-1315 Self-tapping Screw, 3/8-16 x 1.25

7 712-3017 Hex Nut, 3/8-16

8 721-0460 Exhaust Gasket

9 726-0205 Hose Clamp

10 736-0119 Lock Washer, 5/16

11 736-0300 Flat Washer

12 751B221535 Casing Clamp

13 751-0535 Fuel Line Hose

14 751-0564 Muffler Deflector

15 751-0616 Muffler, Twin Inlet

16 751-0650 RH Exhaust Pipe

17 751-0651 LH Exhaust Pipe

18 751-3140 Oil Drain Valve

19 751-3141 Oil Drain Hose

20 751-3142 Oil Drain Cap

21 783-0615B Muffler Heat Shield

22 783-0625C Engine Heat Shield

23 722-0263 Foam (fits over fuel line)

24 746-1086 Throttle Cable

28

1

1

2

3

4

5

6

7

8

9

10

6

11

12

13

14

15

16

17

18

19

20

10

14

9

21

22

23

24

25

5

11

25

26

27

28

31

34

34

44

33

41

38

37

30

42

40

36

39

35

29

1

Models 808H & 808K

46

47

48

45

29

Models 808H & 808K

REF.

NO.

PART

NO. DESCRIPTION

1. 726-3046 Ratchet Clip

2. 731-2247A Hood Shield

3. 747-1184 Support Rod: Air Duct

4. 783-0478A Hood: 8 Style

5. 683-0195 Bracket Assembly

6. 710-0351 Pan Head B Screw #10-16 x 0.5

7. 710-0376 Hex Screw 5/16-18 x 1.0

8. 710-0456 Hex Screw #10-16 x 0.5

9. 710-0599 TT Screw1/4-20 x 0.5

10. 710-0751 Hex Screw 1/4-20 x 0.620

11. 710-0896 AB Screw 1/4-14 x 0.625

12. 710-0924 Machine Screw 1/4-20 x 0.75

13. 712-0271 Sems Nut

14. 712-0292 Nut: Clip

15. 712-0431 Flange Lock Nut

16. 726-0211 U-Nut 5/16-18

17. 731-1854A Lens: 8 Style

18. 735-0126 Rubber Washer

19. 735-0199A Rubber Bumper

20. 736-3039 Flat Washer

21. 783-0475B LH Panel: SD, 8 Style

22. 783-0476C RH Panel: SD, 8 Style

23. 783-0477A Grill: 8 Style

24. 783-0553A Support Bracket: Hood

25. 783-1495 Hinge Bracket: Hood

26. 710-0726 AB Screw 5/16-20 x 0.750

27. 751-0603 Fuel Cap

28. 751-06580 Fuel Tank

29. 710-0599 TT Screw 1/4-20 x 0.5

30. 710-0642 TT SCrew 1/4-20 x 0.75

31. 710-0650 TT Screw 5/16-18 x 0.875

33. 710-0895 Hi-lo Screw 1/4-15 x 0.75

34. 710-1611B TT Screw 5/16-18 x 0.75

35. 710-3217 Machine Screw #8-32 x 0.375

36. 712-0142 Nut 8-32

37. 731-04215 Cruise Lever

38. 731-04217 Brake Lever

39. 731-1857 Control Knob

40. 731-2122C Dash Panel

41. 736-0142 Flat Washer

42. 736-0270 Bell Washer

43. 736-3078 Flat Washer

44. 747-1196 Bent Rod: Lever

45. 749-1087C Support Tube: Dash

46. 768-0010 Bumper Assembly*

47. 714-0145 Internal Cotter Pin*

48. 710-1611B TT Screw 5/16-18 x 0.75*

— 629-0469A Headlight Wire Harness

— 629-1067 Tractor Wire Harness

*Not standard on all tractors.

30

50

14

8

52

17

21

10

20

12

23

21

22

24

6

2

52

14

18

25

19

5

3

4

1

16

9

7

17

15

6

26

Models 808H & 808K

32

57

55

56

49

39

46

6

40

45

41

37

43

42

36

47

48

44

16

30

28

38

33

27

31

34

51

11

28

13

35

54

58

29

59

60

29

61

31

REF.

NO.

PART

NO. DESCRIPTION

1 747-1130B Deck Stabilizer Rod (Model 808H)

747-1324 Deck Stabilizer Rod (Model 808K)

2 683-0197B Lift Shaft Assembly (Model 808H)

683-0462 Lift Shaft Assembly (Model 808K)

3 711-0332 Clevis Pin, .5 x .78

4 712-0206 Hex Nut, 1/2-13

5 712-0431 Flange Lock Nut, 3/8-16

6 712-3004A Flange Lock Nut, 5/16-18

7 712-3083 Hex Nut, 1/2-13

8 714-0104 Internal Cotter Pin

9 714-0145 Internal Cotter Pin

10 716-0106 E-Ring

11 720-0311 Handle Grip

12 732-0874 Torsion Spring

13 732-1184 Extension Spring, .84 x 4.6

14 736-0275 Flat Washer, 5/16

15 736-0921 Lock Washer, 1/2

16 736-3019 Flat Washer, .31 x 1.062 x .134

17 736-3084 Flat Washer, .51 x 1.12 x .06

18 738-0138A Hex Cap Screw, 5/16-18 x .62

19 738-0143 Shoulder Screw, 3/8-16

20 741-0225 Hex Flange Bearing

21 741-0715 Snap Flange Bearing

22 746-0968 Lift Cable, 16.16

23 747-1111A Lift Handle

24 756-1154 Roller Pulley

25 783-0678A Arm Lift

26 783-0720A Deck Stabilizer Bracket

27 710-0260A Carriage Bolt, 5/16 x .62

28 710-0726 AB Screw, 5/16-12 x .75

29 710-0895 Self-tapping Screw, 1/4-15 x .75

30 731-1990 Lift Lever Cover

31 731-1993 Cover w/ Cup Holder

32 736-3078 Flat Washer, .349 x 1.0 x .063

33 783-0677 Lift Adjustment Bracket

34 783-1280 Fender

35 783-1489 Seat Mounting Bracket

36 710-1268 Screw, #10-16 x .375

37 712-3027 Hex Flange Lock Nut, 1/4-20

38 720-0309A Seat Adjuster Grip

39 731-1989 Spacer

40 732-0499 Compression Spring, .41 x 1.5

41 736-0175 Spring Washer, .265 x .562 x .025

42 736-0204 Flat Washer, .344 x .62 x .03

43 738-0137A Shoulder Screw, .340 x .285,1/4-20

44 738-1007 Shoulder Screw, .50 x .50, 3/8-16

45 783-0611 Seat Stop

46 783-0738 Seat Pivot Bracket

47 783-0739 Seat Adjustment Lever

48 783-0753 Seat Adjustment Selector

49 757-04010 High Back Seat, Black

50 735-0656 RH Foot Pad

51 735-0657 LH Foot Pad

— 726-3046 Foot Pad Clips

52 714-0111 Cotter Pin

54 783-0209A LH Seat Lift Bracket

— 17239A RH Seat Lift Bracket

55 710-0924 Phillips Pan Screw, 1/4-20 x .75

56 712-0292 U-type Speed Nut, 1/4-20

57 731-2480 Shift Lever Cover

58 738-0296 Shoulder Screw, .437 x .286

59 731-2618 RH Fender Flare

60 731-2619 LH Fender Flare

61 783-1478 Fender Clips

REF.

NO.

PART

NO. DESCRIPTION

Models 808H & 808K

32

24

23

43

31

29

2

1

2

5

3

9

6

38

7

10

12

13

11

13

14

15

16

17

18

19

21

20

22

20

25

26

27

28

32

30

29

34

30

36

33

37

39

40

11

8

22

4

41

11

Models 808H & 808K

33

Models 808H & 808K

REF.

NO.

PART

NO. DESCRIPTION

1 710-1260A Self-tapping Screw, 5/16-18 x .75

2 710-0604A Self-tapping Screw, 16-18 x .625

3 783-0726B RH Pivot Support Bracket

4 783-0727A LH Pivot Support Bracket

5 783-0728 Pivot Bar Bracket

6 710-0514 Hex Cap Screw, 3/8-16 x 1 (Grade 5)

7 711-1408 RH Drag Link

8 711-1409A LH Drag Link

9 712-0240 Jam Nut, 7/16-20 (Grade 2)

10 712-0241 Hex Nut, 3/8-24 (Grade 2)

11 712-0431 Flange Lock Nut, 3/8-16

12 712-0459 Flange Lock Nut, 7/16-20

13 712-3004A Flange Lock Nut, 5/16-18

14 717-1550D Steering Gear, 11/90 Ratio

15 717-1554 Steering Pinion Gear

16 723-0448A Ball Joint, 7/16-20

17 736-0169 Lock Washer, 3/8

18 736-3084 Flat Washer, .51 x 1.12 x .06

19 738-1001A Steering Shaft, .625 OD x 24.4

20 741-0475 Plastic Bushing, .38 ID

21 741-0656 Hex Flange Bearing, 5/8

22 738-0372B Shoulder Spacer, .38 ID

23 631-04008 Steering Wheel, Three Spoke, Soft Grip

631-04028 Steering Wheel, Three Spoke

24 731-04040 Steering Wheel Cap, Round w/logo

731-04039 Steering Wheel Cap, Round

25 638-0017 LH Axle Assembly, .75 Diameter

26 638-0018 RH Axle Assembly, .75 Diameter

27 719-0525B Cast Iron Pivot Bar w/ Fittings, .75

28 712-0431 Flange Lock Nut, 3/8-16

29 714-0162 Cotter Pin

30 726-0341 Push Cap, .750

31 736-0242 Bell Washer, .34 x .872

32 736-0316 Flat Washer, .78 x 1.59 x .06

33 736-0285 Flat Washer, .635 x 1.589 x .06

34 738-1011 Shoulder Screw, .5 x 2.2, 3/8-16

35 710-0643 Hex Bolt, 5/16-18 X 1

36 634-0183 Wheel Assembly Complete, 16 x 6.5 x 8

634-0182 Rim Only w/ Plastic Bearing

734-0255 Air Valve (Not Shown)

734-1727 Tire Only, Square Shoulder

37 734-2290 Hub Cap

38 783-0653E Steering Support Bracket

39 738-0143 Shoulder Screw, 3/8-16

40 736-0331 Bell Washer, .39 x 1.13 x .062

41 710-04095 Hex Bolt 3/8-16 x 1.0 Special

34

Models 808H & 808K

74

60

8

30

3

21

413

18

16

28

32

8

13

13

73

26

980

55

52

60

50

66 65

22

59

52 57

70 22

30

20

75

22

57

63

46

64

49

53

61

54

52

71

56

67

57

68

63

18

51

52

23

37

48

24

47 64

7

40

36

33

18

45

29

19

14 80

43

17

5

41

6

10

42

34

1

15

20

13

35

20

18

13

1127

20

2

76

77

78

12

12

81

82

83

72

25

13 20

84

85

31

69

44

43

86

35

Models 808H & 808K

REF.

NO.

PART

NO. DESCRIPTION

1 618-0375 Variable-speed Bracket Assembly

2 618-0376 Two-speed Transmission Assembly

3 631-0009A Shfter Knob

4 647-0037 Shift Lever

5 656-0050 Variable-speed Pulley Assembly

6 756-0665 Transmission Pulley, 8.5

7 683-0251 Double-Idler Bracket

8 710-0176 Hex Cap Screw, 5/16-18 x 2.75

9 710-0227 Self Tapping Screw, #8-18 x .5

10 710-0347 Hex Cap Screw, 3/8-16 x 1.75

11 710-0805 Hex Cap Screw, 5/16-18 x 1.5

12 710-0809 Self-tapping Screw, 1/4-20 x 1.25

13 710-0726 AB Screw, 5/16-12 x .75

14 710-3011 Hex Cap Screw, 3/8-16 x 2.25

15 711-0677 Ferrule, 5/16 x .312 Dia.

16 712-0181 Hex Jam Nut, 3/8-16

17 712-0702 Hex Flange Nut, 7/16-20

18 712-0431 Flange Lock Nut, 3/8-16

19 712-0798 Hex Nut, 3/8-16

20 712-3004A Flange Lock Nut, 5/16-18

21 712-3008 Hex Jam Nut, 3/8-16

22 714-0111 Cotter Pin

23 723-3018 Ball Joint, 3/8-24

24 710-1260A LD Screw 5/16-18 x 0.75

25 710-0650 TT Screw 5/16-18 x 0.875

26 732-0384 Extension Spring, .62 Dia. x 6.12

27 732-0716 Extension Spring, .59 OD x 4.0

28 736-0105 Bell Washer, .401 x .870 x .063

29 736-0169 Lock Washer, 3/8

30 736-0275 Flat Washer, 5/16

31 718-0771 Pulley Hub, 1/2 Spline

32 736-0642 Flat Washer, .44 x .75 x .06

33 736-3010 Flat Washer, .407 x .812 x .135

34 738-0322 Shoulder Screw, .625 Dia. x .21

35 747-1122 Brake Rod

36 747-1123A Belt Guard

37 747-1127 Idler Adjustment Rod, 3/8

38 710-1026 Self-tapping Screw, 1/4-20 x 1.75

39 747-1185 Transmission Belt Guard Rod

40 738-0372B Shoulder Spacer, .380 ID

41 754-0468 Variable-speed Belt

42 754-0467 Drive Belt

43 756-0981A Flat Idler, 2.75 OD

44 783-0667B Transmission Torque Bracket

45 783-0669 Idler Bracket

46 647-0031B Brake Control Shaft Assembly

47 647-0032 Speed Control Shaft Assembly

48 683-0266 Drive Pedal Assembly

49 710-1135 Self Tapping Screw, 5/16-18 x 2.5

50 711-0736 Ferrule, 1/4-20

51 711-1363 Pin, 3/8-16 x 2.43

52 714-0104 Cotter Pin

53 732-0437 Compression Spring, .34 OD x 1.0

54 732-0955 Extension Spring, .5 OD x 1.41

55 735-0662 Drive Pedal Pad

56 735-3049 Brake Pedal Pad

57 736-0140 Flat Washer, .281 x .5 x .0625

59 736-0187 Flat Washer, .64 x 1.24 x .06

60 736-0204 Flat Washer, .344 x .062 x .03

61 738-0155 Shoulder Screw, .437 x 1.62

62 738-0507B Shoulder Screw, .5 x .434

63 741-0225 Hex Flange Bearing

64 741-3065B Split Hex Flange Bearing

65 747-04096 Cruise Control Rod

66 747-04093 Brake Lock Control Rod

67 748-0413 Cruise Latch

68 748-0415B Spacer, 5/16 x 1.54

69 783-0653F Steering Support Bracket

70 783-0732 Drive Lockout Bracket

71 783-0773 Brake Pedal

72 736-3008 Flat Washer, .344 x .750 x .120

73 783-0693 Axle Bracket

74 683-0304A Lower Frame Assembly

75 732-0963 Extension Spring, .5 OD x 6.37

76 731-2290 Hub Cap

77 712-3050 Lug Nut, 7/16-14

78 634-0132 Wheel Assembly Complete, 23 x 9.5 x 12

634-0182 Rim Only

734-0255 Air Valve

734-1728 Tire Only, Square Shoulder

79 750-0768 Split Spacer, .25 x .37 x 1.32

80 750-0566A Spacer, .372 x .26 x 1.03

81 712-3026 Jam Nut, 3/4-16

82 736-0316 Flat Washer, .78 x 1.59 x .06

83 710-1611B TT Screw, 5/16-18 x .75

84 747-1185 Transmission Belt Guard Rod

85 710-0599 Self Tapping Screw,1/4-20 x .5

86 756-0639A Engine Pulley, 3.56”

REF.

NO.

PART

NO. DESCRIPTION

IMPORTANT:

For a proper

working machine, use

Factory Approved Parts.

V-belts are designed to

engage and disengage

safely. A substitute (non

OEM) V-belt can be

dangerous by not

disengaging completely.

36

49

48

44*

47

11

34

37

43 15

42

41

23

40

13

10

36

8

12

9

18

20

6

36

21

17

27

14

31

31

36

29

7

12

9

18

38

30

5

28

4

35

22

26

2

25

24

16

1

19

4

32

3

33

46

15

Models 808H & 808K

37

Models 808H & 808K

NOTE: Transmission has a grease capacity of 32 oz. Order part number 737-0148.

NOTE: Upon reassembling transmission input shaft for any reason, refill its cavity with approximately 2/3 oz. of grease.

Order part number 737-0289.

REF.

NO.

PART

NO. DESCRIPTION

1 618-0225 Reverse Collar Assembly

2 618-0226 Hi-Lo Collar Assembly

3 618-0227A Shift Fork Assembly

4 618-0284 Detent Block Assembly

5 618-0285 Output Bearing Block Assembly

6 618-0286 Output Seal Bearing Block Assembly

7 618-0287 Inboard Sealed Axle Block Assembly

8 618-0302 Inboard Sealed Axle Block Assembly

9 618-0365 Wheel Hub Assembly

10 618-0368 Differential Axle Assembly

11 719-0379A Upper Housing

12 641-0002A Axle Bearing Block Assembly

13 661-0012 Brake Assembly

14 710-0642 Self-tapping Screw, 1/4-20 x .75

15 710-0788 Self-tapping Screw, 1/4-20 x 1.0

16 711-1051A Drive Shaft

17 711-1216 Output Shaft

18 712-1329 Nut, 3/4-16

19 713-0446 9-tooth Sprocket

20 713-0447 16-tooth Sprocket

21 713-0448 22-link Chain, .625

22 716-0131 External Snap Ring

23 717-0678 Brake Pad

24 717-1438 41-tooth Bevel Gear

25 717-1439 20-tooth Spur Gear

26 717-1440 10-tooth Spur Gear

27 717-1441 27-tooth Spur Gear

28 717-1442 37-tooth Spur Gear

29 718-0500 Inner Axle Bearing Block

30 718-0504 Shifter Insert

31 718-0505 Shifter Cover

32 718-0537 Shifter Bearing Block

33 719-0385 Lower Housing

34 718-0540 Lockout Plate

35 736-0337 Flat Washer, 5/8 x 1.0

36 736-3046A Flat Washer, 1.01 x 1.86 x .060

37 711-1235 Input Shaft

38 747-1140 Shift Lever

39 750-1033A Spacer, 1.13 x 1.38 x 1.968

40 761-0215 Disc Brake

41 716-0114 Retaining Ring, .56

42 717-1463 13-tooth Bevel Gear

43 736-0335 Flat Washer

44 736-0336 Flat Washer, 5/8 x 1.0 x .030*

736-0337 Flat Washer, 5/8 x 1.0 x ..040*

736-0349 Falt Washer,5/8 x 1.0 x .020*

46 741-0335 Needle Bearing

47 741-0696 Needle Bearing

48 716-0231 E-ring, .75

49 618-0376 Transmisssion Assembly Complete

*Use applicable flat washer (12a, 12b or 12c) in this application allowing proper end-play as instructed in Service Manual.

38

Model 808H

31

6

27

20

21

22

19

37

33

26

34

32

36

35

32

29

24

25

23

30

30

36

35

41

42

41

42

(For reference only) Ground Wire

25

43

32 44

40

45

46

47

48

A

A

1

2

3

47

5

7

8

10

11

12

13

14

16

17

18

28

46

51

52

53

54

55

56

58

59

60

13

57

58

61

63

64

65

11

15

45

4

49 68

67

69

62

70

66

(Note: PTO belt shown in detail

38

with deck assembly)

39

Model 808H

REF.

NO.

PART

NO. DESCRIPTION

1. 783-0653E Steering Support Bracket

2. 647-0064 PTO Lever Engagement Assembly

3. 683-04060 Engagement Plate Assembly

4. 710-1002 Hex Bolt 7/16-20 x 2.0

5. 710-0276 Carriage Screw 5/16-18 x 1.0

6. 710-0344 Hex Screw 3/8-16 x 1.5

7. 710-1238 Hex Head Washer Screw, 5/16-18 x .875

8. 710-3261 Hex Screw 3/8-16 x 7.0

10. 712-0431 Flange Lock Nut

11. 712-3004A Flange Lock Nut

12. 712-3010 Hex Nut

13. 714-0470 Cotter Pin

14. 726-0201 Speed Nut

15. 710-3025 Hex Cap Screw 5/16-18 x .625

16. 732-0944 Extension Spring

17. 732-0991A Belt Guard

18. 732-1013 Belt Guard

19. 725-1706 12 V Battery

20. 710-0751 Hex Cap Screw, 1/4-20 x .62

21. 712-0271 Hex Sems Nut, 1/4-20

22. 712-3087 Wing Nut, 1/4-20

23. 725-1426 Solenoid, 12-Volt, 100 Amp

24. 710-0599 Self Tapping Screw, 1/4-20 x .5

25. 736-0222 Lock Washer, 1/4

26. 783-1033A Hitch Plate

27. 748-0415B Spacer

28. 741-0708 Hex Split Flange Bearing

29. 783-0349 Battery Tray

30. 712-0459 Flange Lock Nut, 7/16-20

31. 783-0891B Deck Stop

32. 710-0604A Self Tapping Screw, 5/16-18 x .625

33. 732-3080 Compression Spring, 1.28 x 3.5

34. 723-0444 Battery Strap

35. 738-1020 Shoulder Screw, .625 x .5, 7/16-20

36. 736-0407 Bell Washer, .45 x 1.0 x .062

37. 738-1132 Shoulder Screw

38. 754-0228 PTO Belt (shown on next page)

40. 783-0693 Axle Bracket

41. 712-3006 Hex Nut 1/4-20

42. 736-0329 Lock Washer

43. 710-0607 TT Screw 5/16-18 x 0.5

44. 710-0642 TT Screw 1/4-20 x 0.75

45. 725-1657A Switch

46. 17962 Switch Plate

47. 710-0224 AB Screw #10-16 x 0.5

48. 683-0304C Lower Frame Assembly

49. 711-1428 Belt Guard Pin

50. 712-0229 Push Nut Retainer

51. 731-2111A PTO Knob

52. 736-0108 Flat Washer

53. 736-0119 Lock Washer

54. 736-0140 Flat Washer

55. 736-0242 Bell Washer

56. 736-0258 Flat Washer

57. 736-0275 Flat Washer

58. 736-0300 Flat Washer

59. 736-3072 Flat Washer

60. 738-0372B Shoulder Spacer

61. 747-1112D Deck Engagement Handle

62. 747-1243 Belt Keeper Rod

63. 756-0487 Idler Pulley

64. 756-0627B Idler Pulley

65. 783-0744A Bracket

66. 736-0119 Lock Washer

67. 736-0171 Lock Washer

68. 736-0322 Flat Washer

69. 750-0956 Spacer

70. 756-1182A Engine Pulley

REF.

NO.

PART

NO. DESCRIPTION

40

9

1

4a

3a

2*

28

5

7

12

11

8

10

13

16

17

18

14

Model 808K

31

6

27

20

21

22

19

37

38

4b

3b

39

32

33

26

34

32

36

35

32

29

24

25

23

30

30

36

35

41

42

41

42

(For reference only) Ground Wire

25

43

32 44

40

45

46

47

48

9

9

15

41

REF.

NO.

PART

NO. DESCRIPTION

1 783-0653E Steering Support Bracket

2 754-0476 PTO Belt

3 717-1774 Elec. PTO Clutch

4 783-1487 PTO Clutch Anti-rot. Brakt.

5 710-0859 Hex Cap Screw, 3/8-16 x 2.5

6 710-1238 Hex Head Washer Screw, 5/16-18 x .875

7 712-0431 Flange Lock Nut, 3/8-16

8 732-0978 Extension Spring, .62 x 5.62

9 712-3004A Flange Lock Nut, 5/16-18

10 710-3180 Hex Cap Screw, 5/16-18 x 1.75

11 712-3010 Hex Nut, 5/16-18

12 683-0294 Idler Bracket Assembly

13 738-3056 Shoulder Screw, 1/2 x 2.5

14 710-3144 Hex Cap Screw, 3/8-16 x 2.0

15 710-3025 Hex Cap Screw, 5/16-18 x .625

16 738-0785 Shoulder Spacer, 1.38 x .445 x .36

17 736-0171 Lock Washer, 7/16

18 710-3157 Hex Cap Screw, 7/16-20 x 3.25

19 725-1706 12-volt Battery, 270 CCA

20 710-0751 Hex Cap Screw, 1/4-20 x .62

21 712-0271 Hex Sems Nut, 1/4-20

22 712-3087 Wing Nut, 1/4-20

23 725-1426 Solenoid, 12-Volt, 100 Amp

24 710-0599 Self Tapping Screw, 1/4-20 x .5

25 736-0222 Lock Washer, 1/4

26 783-1033A Hitch Plate

27 748-0415B Spacer, 3/8 x 1.54

28 756-0627B Idler Pulley, 3.5

29 783-0349 Battery Tray

30 712-0459 Flange Lock Nut, 7/16-20

31 783-0891B Deck Stop

32 710-0604A Self Tapping Screw, 5/16-18 x .625

33 732-3080 Compression Spring, 1.28 x 3.5

34 723-0444 Battery Strap

35 738-1020 Shoulder Screw, .625 x .5, 7/16-20

36 736-0407 Bell Washer, .45 x 1.0 x .062

37 738-1132 Shoulder Screw, 1/4-20, .25 x .15

38 736-0322 Flat Washer, .45 x 1.25 x .164

39 629-04047 Harness Assembly, Electric PTO Clutch

40 783-0693 Axle Bracket

41 712-3006 Hex Nut 1/4-20

42 736-0329 Lock Washer

43 710-0607 TT Screw 5/16-18 x 0.5

44 710-0642 TT Screw 1/4-20 x 0.75

45 725-1657A Switch

46 17962 Switch Plate

47 710-0224 AB Screw #10-16 x 0.5

48 683-0304C Lower Frame Assembly

REF.

NO.

PART

NO. DESCRIPTION

IMPORTANT:

For a proper

working machine, use

Factory Approved Parts.

V-belts are designed to

engage and disengage

safely. A substitute (non

OEM) V-belt can be

dangerous by not

disengaging completely

.

Model 808K

42

Model 808H

29

13

10

27

42

25

53

52

2

13

59

5

44

35

55

21

9

25

45

4

12

38

40

41

30

26

34

49

47

1

43

29

33

50

7

30

48

36

27

42

32

4

6

51

39 46

42

29

28

26

37

19

8

11

3

14

24

24

15

17

57

18

20

23

16

24

58

23

29

15

56

18

60

61

62

63

64

65

66

65

25

67

68

69

70

71

43

IMPORTANT:

For a proper

working machine, use

Factory Approved Parts.

V-belts are designed to

engage and disengage

safely. A substitute (non

OEM) V-belt can be

dangerous by not

disengaging completely.

Model 808H

REF.

NO.

PART

NO. DESCRIPTION

1. 17116 Brake Assembly: Deck

2. 17258C Deck Belt Cover

3. 17982 Spindle Reinforcement Plate

4. 618-0430A Spindle Assembly, 5.0 Dia.

756-1187 Pulley Only

5. 618-0595 Double Pulley Spindle Assembly

756-0603 Double Pulley Only

6. 683-0199C SD Deck Assembly: 46 inch

7. 683-0254 Deck Adjustment Bracket Assembly

8. 710-0167 Carriage Screw, 1/4-20 x .50

9. 710-0344 Hex Cap Screw, 3/8-16 x 1.5

10. 710-0501 Hex Cap Screw, 1/4-20 x 2.0

11. 710-0514 Hex Cap Screw, 3/8-16 x 1.0

12. 710-0528 Hex Cap Screw, 5/8-18 x 1.25

13. 710-0599 Self-tapping Screw,1/4-20 x .5

14. 710-0650 Self-tapping Screw,15/16-18 x .875

15. 710-0703 Hex Screw, 1/4-20 x .75

16. 710-0751 Hex Cap Screw, 1/4-20 x .62

17. 710-0805 Hex Bolt 5/16-18 x 1.5

18. 710-1260A Self-tapping Screw, 5/16-18 x .75

19. 710-3180 Hex Bolt 5/16-18 x 1.75

20. 711-04069 Grasscatcher Pin

21. 711-0993 Belt Guard Pin

22. 711-1554 Pin

23. 712-0271 Hex Sems Nut, 1/4-20

24. 712-0417A Hex Flange Nut, 5/8-18

25. 712-0431 Flange Lock Nut, 3/8-16

26. 712-3004A Flange Lock Nut

27. 712-3006 Hex Nut, 1/4-20

28. 712-3010 Hex Nut 5/16-18

29. 712-3027 Hex Flange Lock Nut, 1/4-20

30. 714-0470 Cotter Pin, 1/8 x 1.25

31. 717-1553B Deck Adjustment Gear

32. 726-0233 Push Nut. .25 x .5

33. 732-0306 Compression Spring, .406 x .531 x 1.75

34. 732-0429A Extension Spring

35. 732-0594A Extension Spring, .91 x 7.3

36. 732-0934 Extension Spring

37. 732-1165 Extension Spring

38. 734-0973 Deck Wheel

39. 734-3058B Deck Wheel

40. 736-0119 Lock Washer, 5/16

41. 736-0140 Flat Washer

42. 736-0270 Bell Washer, .265 x .75 x .062

43. 736-0418A Flat Washer

44. 738-0347 Shoulder Spacer

45. 738-0373 Shoulder Screw

46. 738-3056 Shoulder Screw

47. 746-1107 Bracket Cable

48. 747-1116 Deck Release Pin

49. 748-0234 Shoulder Spacer

50. 750-1320 Spacer

51. 754-0228 V-Belt

52. 754-0349 Deck Belt, Poly

53. 756-0627B Idler Pulley, 3.5

55. 783-0139A Idler Bracket

56. 783-0141 Center Deck Skirt

57. 783-0142 RH Deck Skirt

58. 783-1025 Chute Stop

59. 783-1347A LH Belt Cover

60. 731-1032B Chute Deflector: Side Discharge

61. 726-0106 Speed Nut

62. 711-0792 Hinge Pin

63. 703-1693A Mounting Bracket

64. 732-0602 Torsion Spring

65. 742-0611 Blade: 16.28” Star

66. 742-0612 Blade: 14.88” Star

67. 731-1636 Mulch Plug†

68. 712-3087 Wing Nut†

69. 712-3006 Hex Nut†

70. 710-0578 Machine Screw†

71. 736-0173 Flat Washer†

REF.

NO.

PART

NO. DESCRIPTION

† If equipped

44

Model 808K

2

34

18

29

27

23

11

23

2729

29 829

22

27

9

49

50

61

26

45

14

22

27

29 74

23

16

64

53

4453

64

37

29

72

25

20

57

68

56 29

73

29

69

5

68

60

57

20

29

36

46

63 4

15

51

40

29

66

6

17

17

75

3

67

3

7

14

16

29

47

58

32

14

30

54

31

29

24

71

1

35

39

59 38

52

65

43

52

65

52 39

23

27

38

10

23

27

29

19

A

A

55

33 62

28

22

76

13

23

22

77

23

23 14

78

70

45

REF.

NO.

PART

NO. DESCRIPTION

1. 12650 Bracket, Adjustment, Height

2. 16606 Bracket, Hook, Retainer

3. 618-0671 Spindle Assembly, Pulley, 5.39 Dia x .5625

4. 683-0254 Bracket Assembly, Deck, Hanger LH

5. 683-0459 Idlr Assembly, 54"

6. 683-0608 Bracket Assembly, Lift, 54"

7. 683-0609 Bracket Assembly, LH-Front

8. 683-0610 Bracket Assembly, RH-Front

9. 683-0617 Stop Assembly, Chute

10. 703-2093 Baffle, RR, Inner

11. 703-2392 Bracket

12. 703-3511 Guard, Finger

13. 710-0216 Hex Screw 3/8-16 x 0.75

14. 710-0514 Hex Screw 3/8-16 x 1.0

15. 710-0528 Hex Screw, 5/16-18 x 1.25

16. 710-0602 Screw, Self-tapping, 5/16-18 x 1.000

17. 710-0726 Screw, AB, 5/16-12 x 0.75

18. 710-0751 Hex Screw, 1/4-20 x .620

19. 710-1644 Screw, Carriage, 3/8-16 x 5.00

20. 710-3011 Hex Screw, 3/8-16 x 2.25

21. 710-3073 Hex Screw, 5/16-18 x 2.25

22. 710-3168 Bolt, Carriage, 3/8-16 x 1.0

23. 710-3178 Short Neck Carriage Bolt 3/8-16 x .75

24. 711-0332 Pin, Clevis, .50 Dia x .78

25. 711-1737 Pin, Roller, .5" Dia x 10.06 .

26. 711-1762 Pin, Hinge, Dia .375 x 14.06

27. 712-0229 Push Nut Retainer

28. 712-0417A Nut, Hex Flange, 5/8-18

29. 712-0431 Nut, Flange Lock, 3/8-16

30. 712-0641 Hex Nut M16

31. 712-3004A Nut, Flange Lock, 5/16-18, Gr5

32. 712-3010 Nut, Hex, 5/16-18, Gr5

33. 712-3022 Nut, Hex Lock, 1/2-13

34. 712-3027 Nut, 1/4-20, Hexflg, Lock

35. 714-0145 Pin, Click, .092 x 1.64

36. 714-0470 Pin, Cotter, 1/8 x 1.25

37. 714-3004 Pin, Cotter, 3/32 x 1.25

38. 715-0108 Pin, Sprg, 1/4 Dia x 1.00

39. 715-0246 Pin, Spring, 3/16 x 1.25

40. 717-1553B Adjustment, Deck, Gear

41. 721-04041 Water Nozzle Adaptor

43. 731-0335 Roller, Deck

44. 731-3005 Front Roller

45. 731-3131A Deflector, Chute

46. 732-0306 Spring, Compression, .406 x .531 x 1.75

47. 732-0459 Spring, Extension, .94 Dia x 6.74

48. 732-0934 Spring, Extension, 1.15 Dia x 5.99

49. 732-3070 Torsion Spring .44 I.d. x 2.10

50. 734-3058B Deck Wheel, 5" Dia.

51. 736-0119 Lock Washer

52. 736-0134 Flat Washer, .812 ID x 1.38 OD x .1

53. 736-0208 Flat Washer, .51 ID x 1.5 OD x .07

54. 736-0760 Lock Washer

55. 736-0921 Washer, Lock, 1/2 , Regular Duty

56. 736-3039 Flat Washer .406 ID X 1.5 x 11ga

57. 736-3072 Washer, Flat .38 ID x.93 OD x.110

58. 737-04003 Water Nozzle: Deck Wash-Out System

59. 738-0295 Shoulder Screw, .750 x .47.12

60. 738-1229A Shoulder Screw

61. 738-3056 Shoulder Screw, 1/2 Dia x 2.50 .

62. 742-0677 Blade, 18.50"

63. 747-1116 Deck Release Handle Rod, .375 Dia

64. 750-0151 Spacer .550 ID x .755 OD x 1.1

65. 750-0212 Spacer, .82 ID x 1.00 OD x .53

66. 750-3213 Spacer, .405 x .75 x 3.875

67. 754-0642 Belt, V-Type, B Section

68. 756-3105 Pulley, Idler, 5.0 Dia.

69. 783-04013A Bracket, Stabilizing

70. 783-04232 Deck: SD w/Water Nozzle Ftg.

71. 783-1453 Bracket, Mounting, 54" Roller

72. 783-1454 Bracket, Roller, Front

73. 783-1455 Bracket, Idler

74. 783-1470 Cover, Spindle RH

75. 783-1471 Cover, Spindle LH

76. 783-1482 RH Skirt

77. 783-1483 LH Skirt

78. 783-1484 LH Extension Skirt

REF.

NO.

PART

NO. DESCRIPTION

IMPORTANT:

For a proper

working machine, use

Factory Approved Parts.

V-belts are designed to

engage and disengage

safely. A substitute (non

OEM) V-belt can be

dangerous by not

disengaging completely.

Model 808K

46

YOUR NOTES

Date Comments

47

YOUR NOTES

Date Comments

48

MANUFACTURER’S LIMITED WARRANTY FOR:

The limited warranty set forth below is given by MTD LLC with

respect to new merchandise purchased and used in the

United States, its possessions and territories.

MTD LLC warrants this product against defects for a period of

two (2) years commencing on the date of original purchase

and will, at its option, repair or replace, free of charge, any

part found to be defective in materials or workmanship. This

limited warranty shall only apply if this product has been

operated and maintained in accordance with the Operator’s

Manual furnished with the product, and has not been subject

to misuse, abuse, commercial use, neglect, accident,

improper maintenance, alteration, vandalism, theft, fire,

water, or damage because of other peril or natural disaster.

Damage resulting from the installation or use of any

accessory or attachment not approved by MTD LLC for use

with the product(s) covered by this manual will void your

warranty as to any resulting damage.

Normal wear parts or components thereof are subject to

separate terms as follows: All normal wear parts or

component failures will be covered on the product for a period

of 90 days regardless of cause. After 90 days, but within the

two year period, normal wear part failures will be covered

ONLY IF caused by defects in materials or workmanship of

OTHER component parts. Normal wear parts and

components include, but are not limited to: batteries, belts,

blades, blade adapters, grass bags, rider deck wheels, seats,

snow thrower skid shoes, shave plates, auger spiral rubber,

and tires.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE, through your local authorized

service dealer. To locate the dealer in your area, check your

Yellow Pages, or contact MTD LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-

330-220-4683 or log on to our Web site at

www.mtdproducts.com.

This limited warranty does not provide coverage in the

following cases:

a. The engine or component parts thereof. These items

carry a separate manufacturer’s warranty. Refer to

applicable manufacturer’s warranty for terms and

condition.

b. Log splitter pumps, valves, and cylinders have a sepa

rate one year warranty.

c. Routine maintenance items such as lubricants, filters,

blade sharpening, tune-ups, brake adjustments, clutch

adjustments, deck adjustments, and normal

deterioration of the exterior finish due to use or

exposure.

d. MTD LLC does not extend any warranty for products

sold or exported outside of the United States, its

possessions and territories, except those sold through

MTD LLC’s authorized channels of export distribution.

e. Parts that are not genuine MTD parts are not covered

by this warranty.

f. Service completed by someone other than an

authorized service dealer is not covered by this

warranty.

g. Transportation charges and service calls are not

covered.

No implied warranty, including any implied warranty of

merchantability of fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty, whether written or oral, except as

mentioned above, given by any person or entity,

including a dealer or retailer, with respect to any product,

shall bind MTD LLC. During the period of the warranty,

the exclusive remedy is repair or replacement of the

product as set forth above.

The provisions as set forth in this warranty provide the

sole and exclusive remedy arising from the sale. MTD

LLC shall not be liable for incidental or consequential

loss or damage including, without limitation, expenses

incurred for substitute or replacement lawn care services

or for rental expenses to temporarily replace a warranted

product.

Some states do not allow the exclusion or limitation of

incidental or consequential damages, or limitations on how

long an implied warranty lasts, so the above exclusions or

limitations may not apply to you.

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration

of safety features of the product shall void this warranty.

You assume the risk and liability for loss, damage, or injury to

you and your property and/or to others and their property

arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser or to the person for whom it was purchased

as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This

limited warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683