MTD OEM 190 032 User Manual To The A230627a 0322 67a4 Dd5c A8569032f7db

User Manual: MTD OEM-190-032 to the manual

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty

OPERATOR’S MANUAL

Model
OEM-190-032
190-032-101

42-inch Two-Stage Snow Thrower Attachment
For FastAttach™ Compatible Lawn Tractors & Garden Tractors

PRINTED IN U.S.A.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

FORM NO. 769-01933F
11/8/07

This Operator’s Manual is an important part of your snow thrower attachment. It will help you assemble,
prepare and maintain the unit for best performance. Please read and understand what it says.

TABLE OF CONTENTS
1. Rider Model Identification................................. Page 3
2. Important Safe Operation Practices................. Page 4
3. Carton Contents............................................... Page 8
4. Assembly & Attaching Undercarriage............... Page 10
5. Assembling Controls......................................... Page 12
6. Mounting Auger Housing................................. Page 13
7. Belt Routing...................................................... Page 14

8. Controls.......................................................... Page 15
9. Operation........................................................ Page 16
10. Adjustments................................................... Page 17
11. Maintenance................................................... Page 18
12. Parts List......................................................... Page 19
Warranty......................................................... Back Cover

Finding and Recording Model Number
BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT,
please locate the model plate and copy the information from it in this Operator’s Manual for future reference. The information on
the model plate is very important if you need help from our Customer Support Department or your authorized dealer. You can
locate it by looking on the top rear portion of the auger housing:

Model Number

Serial Number

*Locate the model plate on your snow thrower attachment and copy the information from it in the space provided above for future reference.

Customer Support
Please do NOT return the unit to the retailer from which it was
purchased, without first contacting Customer Support.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this
unit, you can seek help from the experts. Choose from the options below:
• Visit www.mtdproducts.com. Click on the Service & Support menu option.
• Phone a Customer Support Representative at 1-800-800-7310.
• Please have your unit’s model number and serial number ready when you call. See above to locate this information. You will
be asked to enter the serial number in order to process your call.

To The Owner

Model Plate

Assistance may be needed to complete the installation of
this attachment.

.ccotsm 800-800-7310
w td p ro d u
w w .m

MTD LLC
P. O. BOX 361131
44136
CLEVELAND,OH
330-220-4683

Determine The Model
of Your Rider
This manual is designed for installation of your new snow
thrower attachment on several different tractors. It is
important for you to determine which model of tractor that
you have.

Rider Model
Identification

To determine the model of tractor, locate the model plate
found underneath the seat. The model plate consists
of an 11 digit/letter model number and a serial number.
For ease in this installation and for future use, copy your
tractor’s model number & serial number below now:

Figure 1-1

Rider Model Number:__ __ __ __ __ __ __ __ __ __ __
Rider Serial Number:_________________________
The 5th, 6th & 7th numbers from the left in your model
number determine your rider’s model series. See Fig. 1-2.

Sample Model Number
13AM 7 9 0 G000

When you fill in your model number in the space above,
the actual model series number should fall into the gray
shaded area.

Indicates Model Series 700

If you have a 700 model series rider, you will need to
acquire the service kit number 753-05097A to complete
this installation. Call a customer support representative
as instructed on Page 2 of this manual. For other models
follow the instructions in this manual.

Figure 1-2

NOTE:
References to LEFT
and RIGHT indicate the
left and right sides of
the tractor when facing
forward in the operator’s
position. Reference to
the FRONT indicates the
grille end; to the REAR,
the rear end of the rider.

Important Safe Operation Practices

WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!

California Proposition 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.

Training

Preparation

Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.

Thoroughly inspect the area where the equipment is to be
used. Remove all door mats, newspapers, sleds, boards, wires
and other foreign objects which could be thrown by the
auger/impeller.

Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.

Always wear safety glasses or eye shields during operation and
while performing an adjustment or repair to protect your eyes.
Thrown objects which ricochet can cause serious injury to the
eyes.

Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.

Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other loose
clothing which could become entangled in moving parts. Wear
footwear which will improve footing on slippery surfaces.

Never allow adults to operate this machine without proper
instruction.

Adjust collector housing height to clear gravel or crushed rock
surfaces.

Thrown objects can cause serious personal injury. Plan
your snow throwing pattern to avoid discharge of material
toward roads, bystanders and the like.

Disengage all clutches and shift into neutral before starting the
engine.

Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.

Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual(s).

Let tractor engine and attachment adjust to outdoor
temperature before starting to clear snow.

Exercise caution while operating tractor with this
attachment, especially when traveling in reverse.

Do not operate machine while under the influence of
alcohol or drugs.

Muffler and engine become hot and can cause a burn. Do
not touch.

Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic. Do
not carry passengers.

Exercise caution when changing direction and while
operating on slopes.

Do not clear snow across the face of slopes; go up and
down. Exercise extreme caution when operating on slopes.
Do not attempt to clear steep slopes.

Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times, until refueling is
complete. Do not use a nozzle lock-open device.

Plan your snow throwing pattern to avoid discharge
towards windows, walls, cars etc. To avoid property
damage or personal injury caused by a ricochet.

10.

Extinguish all cigarettes, cigars, pipes and other sources
of ignition.

Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.

11.

Never fuel machine indoors.

Do not overload machine capacity by attempting to clear
snow at too fast of a rate.

Never remove gas cap or add fuel while the engine is hot
or running.

12.

Never operate this machine without good visibility or light.

13.

Allow engine to cool at least two minutes before
refueling.

Disengage power to the auger/impeller when transporting
or not in use.

14.

Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.

Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when in reverse.

15.

If the machine should start to vibrate abnormally, stop
the engine, disengage the power take-off, lower the
attachment and set the parking brake. Inspect thoroughly
for damage. Repair any damage before starting and
operating.

16.

After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, thoroughly inspect
the snow thrower for any damage, and repair the damage
before restarting and operating the snow thrower.

17.

Disengage the power take-off, lower attachment, set
the parking brake and stop engine before you leave the
operating position. Wait until the auger/impeller comes to
a complete stop before unclogging the discharge chute,
making any adjustments, or inspections.

18.

Do not carry passengers.

To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
a.

Use only an approved gasoline container.

Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on
the ground, away from your vehicle, before filling.

When practical, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this is
not possible, then refuel such equipment on a trailer
with a portable container, rather than from a gasoline
dispenser nozzle.

Replace gasoline cap and tighten securely.

If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.

Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).

m. Allow machine to cool at least 5 minutes before storing.

Operation
1.

Do not put hands or feet near rotating parts, in the auger/
impeller housing or discharge chute. Contact with the
rotating parts can amputate hands and feet.

Never operate with a missing or damaged discharge chute.
Keep all safety devices in place and working.

19.

Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).

When cleaning, repairing or inspecting the snow thrower,
make certain the collector/impeller and all moving
parts have stopped. Disconnect the spark plug wire and
keep the wire away from the plug to prevent someone
from accidentally starting the machine. Do not run the
engine indoors, except when starting the engine and for
transporting the snow thrower in or out of the building.
Open the outside doors; exhaust fumes are dangerous.

20.

If situations occur which are not covered in this manual,
use care and good judgment. Contact your dealer or
telephone 1-800-800-7310 for assistance and the name of
your nearest servicing dealer.

Section 2 — Important Safe Operation Practices

Clearing A Clogged Discharge Chute

Maintenance And Storage

Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.

Never tamper with safety devices. Check their proper
operation regularly.

Disengage power take-off, lower the attachment, set the
parking brake, stop engine and remove key to prevent
unintended starting. Wait until the auger/impeller comes to a
complete stop before cleaning, repairing, or inspecting.

Check bolts, and screws for proper tightness at frequent
intervals to keep the machine in safe working condition. Also,
visually inspect machine for any damage.

Do not change the engine governor setting or over-speed the
engine. The governor controls the maximum safe operating
speed of the engine.

Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (O.E.M.) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”

Check clutch controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the PTO
and safety interlock system in your tractor’s operator’s manual
for instructions.

Maintain or replace safety and instruction labels, as necessary.

Observe proper disposal laws and regulations for gas, oil, etc.
to protect the environment.

Prior to storing, run machine a few minutes to clear snow from
machine and prevent freeze up of auger/impeller.

10.

Never store the machine or fuel container inside where there
is an open flame, spark or pilot light such as a water heater,
furnace ,clothes dryer etc.

11.

Always refer to the operator’s manual for proper instructions
on off-season storage.

To clear the chute:
1.

SHUT THE ENGINE OFF!

Wait 10 seconds to be sure the impeller blades have
stopped rotating.

Always use a clean-out tool, not your hands.

warning! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Section 2 — Important Safe Operation Practices

NOTES:
Use this page to make
notes and write down
important information.

Undercarriage Assembly

Self-Adhesive
Reflectors

Carton
Contents

Cable Ties

Belt Keeper &
Lock Nut

If you are missing
any parts, please
do not contact the
retailer where you
purchased this unit,
call MTD directly at
1-330-220-4MTD or
toll free at
1-800-800-7310.

Extension
Spring

Quick
Release Pins

Extension
Spring

Shoulder Bolts
& Lock Nuts

Upper Chute
Crank Rod

Cotter Pin

Lift Handle
Assembly

Spare Shear Bolts
& Cotter Pins

Auger Housing
Assembly w/
Linkage

Figure 3

CONTENTS OF CARTON
Before beginning installation, remove all parts from the carton to make sure everything is present. Carton
contents are listed below and shown in Figure 3. Hardware part numbers are shown in parentheses.
• One Auger Housing Assembly w/ Lower V-belt
• One Undercarriage Assembly w/ Upper V-belt
• One Lift Handle Assembly (with mounting hardware attached)
• One Upper Chute Crank Rod (with mounting hardware attached)
• Three Cable Ties (725-0157)
• Two Spare Shear Pins (738-04124) & Cotter Pins (714-04040)
• One Cotter Pin (714-0507)
• Two Self-adhesive Reflectors (730-3000)
• Extension Spring (732-0594A)
• Extension Spring (732-04237)
• Two Quick Release Pins (714-04061)
• Two Shoulder Bolts & Lock Nuts (738-0143 & 712-04065)
• One Belt Keeper Pin & Flange Lock Nut (711-1000 & 712-04065)

Carton
Contents

If you are missing
any parts, please
do not contact the
retailer where you
purchased this unit,
call MTD directly at
1-330-220-4MTD or
toll free at
1-800-800-7310.

Assembly
& Attaching
Undercarriage

WARNING: Before installing attachment, place tractor on a firm and level surface. Place the
PTO in the disengaged (OFF) position, set the parking brake, shut engine off and remove key
to prevent unintended starting.
NOTE: References to LEFT and RIGHT indicate the left and right sides of the tractor when facing forward in the
operator’s position. Reference to the FRONT indicates the grille end; to the REAR the drawbar end.
IMPORTANT: You must first figure out which model of rider you are attaching this snow thrower to. Refer to Determine
Your Model of Rider on page 3 of this manual to determine what model rider you are attempting to install this attachment
to. Then proceed to the applicable instructions for your model of rider.
Your tractor’s cutting deck, PTO belt and front deck stabilizer bracket must be removed prior to mounting the snow
thrower attachment. Refer to your tractor’s Operator’s Manual for detailed instructions. If your tractor is equipped with
any front-end accessory (i.e. front bumper kit), it must also be removed.

Do you have an Electric PTO or Manual PTO?
If you engage your tractor’s cutting deck by using your left hand to pivot a lever forward, your tractor has a Manual
PTO. If you engage your tractor’s cutting deck by pulling outward on a small knob located on the tractor’s dash, your
tractor has an Electric PTO.

WARNING
Before installing
attachment, place
tractor on a firm
and level surface.
Place the PTO in
the disengaged
(OFF) position, set
the parking brake,
shut engine off and
remove key to prevent
unintended starting.

Mounting the Idler Assembly
Electric PTO Undercarriage
Assembly Setup
Proceed as follows when mounting this snow thrower
attachment to a tractor equipped with a 42, 46, 50 or
54-inch deck with electric PTO:
1. Attach one end of the extension spring (732-0594A)
to the hole in the idler assembly. Mount the opposite
end of the extension spring to the belt keeper pin as
illustrated in Fig. 4-1.
2. Refer to Fig. 4-2 for correct position.

Manual PTO Undercarriage
Assembly Setup
1. Install belt keeper pin as seen in Fig. 4-3.
2. Attach the PTO cable to the idler bracket, then fit the
cable into the slotted fitting as seen in Fig. 4-3.
NOTE: The PTO cable should be hanging down under
you tractor after you removed the mowing deck. You will
need to slide the undercarriage unit under your tractor in
position for which it will be mounted. The slanted side
should be pointed towards the front of your tractor.
2. Refer to Fig. 4-4 for correct position.

Extension Spring

PTO Cable

Belt Keeper
Idler Pulley &
Idler Bracket

Idler Pulley &
Idler Bracket

Belt Keeper Pin
Slotted Fitting

Figure 4-1

Flange Lock Nut
Figure 4-3

Figure 4-2

Figure 4-4

Mounting The
Undercarriage Assembly
1. Remove and retain the four hairpin clips from the
weld pins found on the top side of the undercarriage
assembly. Remove and retain the two clevis pins with
hairpin clips. This hardware is for later installation.
See Fig. 4-5.
2. With the undercarriage assembly beneath the tractor,
see Fig. 4-6, lift the undercarriage assembly up
against the frame of the tractor. The weldpins on the
top of the undercarriage assembly should go through
the aligning holes found along the tractor’s frame.
See Fig. 4-7.

Figure 4-7

3. Fasten the undercarriage assembly to the frame with
the hairpin clips removed in step 1. See Fig. 4-8
4. Route the upper drive belt around the engine pulley.
See Fig. 4-7.
NOTE: Proceed to the Assembling Controls section of
this manual if you have an Electric PTO.

Assembly
& Attaching
Undercarriage

WARNING

5. Attach the extension spring to the idler pulley. See Fig.
4-9. Connect the other end to tractor’s frame rail. See
Fig. 4-10.
Figure 4-8

Figure 4-5
Figure 4-9

Figure 4-10

Figure 4-6

Before installing
attachment, place
tractor on a firm
and level surface.
Place the PTO in
the disengaged
(OFF) position, set
the parking brake,
shut engine off and
remove key to prevent
unintended starting.

Assembling
Controls

Attaching Chute
Directional Control
1. Attach the chute directional control assembly to the
upper lift link on the left side of the auger housing.
Assemble with two hex screws as illustrated in
Figure 6-1. Secure with two flange nuts.

Attaching Lift Handle
1. Attach lift handle to lift bracket on the right side of
auger housing assembly with two hex screws and two
flange nuts provided. See Fig. 6-3.
2. Fasten lift cable to the lift handle with two of the cable
ties provided. Pull cable ties until snug and trim excess.
Lift Handle

1. Secure the upper chute crank rod to the joint block
(A) on the lower chute crank rod with the cotter pin
(B) provided. See Figure 6-2.
3. Fasten chute tilt cables to chute directional control
with two of the cable ties provided. Pull cable ties
until snug and trim excess.

Upper Lift Link

NOTE:
All references to left
or right side of the
snow thrower is
from the operating
position only.

Chute Directional
Control Assembly

Auger Housing Assembly
Figure 6-3

Mounting Auger Assembly
WARNING: Before installing
attachment, place tractor on a firm
and level surface. Place PTO in the
disengaged (OFF) position, set the
parking brake, shut engine off and remove key to
prevent unintended starting.

Figure 6-1

IMPORTANT: If you are installing this snow thrower
attachment on any tractor model with a side discharge
muffler, See Fig. 6-4, then the heat shield on the auger
housing must be removed. See Fig. 6-5. To remove the
heat shield remove the four lock nuts and bolts (two on
either side of the unit) securing the heat shield to the lift
linkage. See Fig. 6-5.

B
A

Figure 6-2

Figure 6-4

Attaching Reflectors
Peel off the backing from each of the reflectors to
expose the adhesive surface. Adhere the reflectors to
the rear of the tractor’s fender (one on the left and one
on the right) so that the reflectors simulate taillights.

Mounting
Auger
Housing

Heat Shield

Figure 6-5
IMPORTANT: It will be necessary to have a second
person assist you to complete the following steps.
1. Install a shoulder bolt on each side of the tractor and
secure with a lock nut, as seen in Fig. 6-7
Shoulder Bolt

2. Position the auger housing assembly in front of the tractor
as seen in Fig. 6-6. Lay the belt and support tubes on the
installation surface.

Figure 6-7

3. Carefully move the tractor forward (by pushing, NOT
driving it) so that support tubes found on the rear of
the auger housing assembly are positioned between
the tractor’s front tires. Set the parking brake.
4. With the help of an assistant, lift up the auger housing
and move it so that it rests over the shoulder bolts
installed in Step 1 of this section. See Fig. 6-7.
5. Maneuver the auger housing until the mounting holes
line up. Insert the two quick release pins from your
hardware pack into the top hole on each side as seen in
Fig. 6-8.

Attaching Support Tubes
1. Secure the left support tube to the front of the
undercarriage assembly with the clevis pin and hairpin
clip removed earlier. See Fig. 6-9.

Quick Release Pin
Figure 6-8

2. Repeat the previous step on the right side.

Belt
Support Tube
Figure 6-9

Figure 6-6

WARNING
Before installing
attachment, place
tractor on a firm and
level surface. Place
the PTO in the disengaged (OFF) position,
set the parking brake,
shut engine off and
remove key to prevent
unintended starting.

Routing the Upper Drive Belt (Tractors Models with an Electric PTO)
Engine Pulley

Spindle Pulley

All electric PTO
Decks 42, 46, 50, 54

Belt
Routing

Various Models

PTO Idler Pulley
Figure 8-1
1. Attach and route upper drive belt around spindle pulley and idler pulley found on undercarriage, electric PTO
clutch and PTO idler pulley as illustrated in Fig. 8-1. Make sure that the belt is routed to the INSIDE of the belt
keeper on the undercarriage idler pulley and the remaining keeper pins found around the spindle pulley.

WARNING
Before installing
attachment, place
tractor on a firm and
level surface. Place
the PTO in the disengaged (OFF) position,
set the parking brake,
shut engine off and
remove key to prevent
unintended starting.

IMPORTANT: Make certain that the flat side of the belt is facing outward as it sits against both the electric PTO
clutch and spindle pulley. This allows the “V” side of the belt to ride snugly in both pulleys.

Routing the Upper Drive Belt (Tractor Models with a Manual PTO)
Spindle Pulley

Engine Pulley

All Manual PTO
Decks 38, 42, 46
PTO Idler Pulley
Figure 8-2

IMPORTANT:
Make certain that the
flat side of the belt is
facing outward. This
allows the “V” side of
the belt to ride snugly
in both pulleys.

1. Attach and route the upper drive belt around the engine pulley and spindle pulley, routed to the INSIDE of the
PTO idler pulley on the undercarriage. Make sure the belt is routed inside of the belt keeper pins found around
the spindle pulley and engine pulley. See Fig. 8-2.
IMPORTANT: Be certain flat side of belt is facing outward. This allows “V” side of belt to ride snugly in both pulleys.

Routing the Lower Drive Belt (All Tractors Models)
Left Side
Spindle Pulley

Undercarriage
Double-Idler Bracket

Snow Thrower Drive Pulley

Right Side
Figure 8-3
1. Attach and route the lower drive belt around the lower pulley on the spindle assembly, both pulleys on the doubleidler bracket found beneath the undercarriage, and the drive pulley found on the rear of the snow thrower housing
as illustrated in Fig. 8-3.
2. Attach tension spring (found on undercarriage double-idler bracket) to the hex screw if it is not already attached.

WARNING: Be familiar with all controls
and their proper operation. Know how
to stop the machine and disengage
them quickly.

Engaging the Augers
and Impeller
Power to the snow thrower attachment is activated by
engaging the tractor’s PTO.
1. Place the tractor’s throttle control in the FAST (rabbit)
position and allow it to remain there for efficient snow
removal.
2. Move the PTO knob or PTO lever (on tractor’s so
equipped) into the “ON” position to engage the augers
and impeller.
3. Move the PTO knob or PTO lever (on tractor’s so
equipped) into the “OFF” position to disengage the
augers and impeller.
NOTE: The PTO knob (on units so equipped) cannot be
in the engaged (ON) position when the tractor is driving
in the reverse direction. The PTO knob must be in the
disengaged (OFF) position when the shift lever is placed
in REVERSE or the electric PTO clutch will automatically
shut off.
Refer to your tractor’s Operator’s Manual for more
information regarding your tractor’s PTO and safety
interlock system.
Trigger Control

Lift Handle
The lift handle is located on the right side of tractor and
is used to raise and lower snow thrower attachment.
1. To raise snow thrower attachment off of the ground,
pull rearward and down on the lift handle until
you feel the lift latch on the right side of the snow
thrower engage, locking the snow thrower in a raised
position See Fig. 9-1.

Controls

2. To lower the snow thrower, push downward on the
lift handle until there is enough slack in the lift cable
so that you may squeeze the trigger control. With
the trigger control squeezed, gently allow the snow
thrower to lower until it reaches the ground.

Chute Directional
Control
The chute directional control assembly is found on
the left side of the tractor and includes both the chute
tilt lever as well as the chute crank. Both affect the
direction that the discharged snow is thrown.
To pivot upper section of discharge chute, affecting the
distance and angle which the snow is thrown, move
the chute tilt lever forward or rearward into a desired
position.

WARNING
Be familiar with all
controls and their
proper operation.
Know how to stop
the machine and
disengage them
quickly.

The direction which snow is thrown can be changed
by rotating the discharge chute with the chute crank.
Turn the chute crank clockwise to rotate the chute and
discharge snow to the left. Crank it counterclockwise to
rotate the chute and discharge snow to the right.

Chute Directional Control

Lift Handle

Figure 9-1

NOTE:
The PTO knob (on
units so equipped)
cannot be in the
engaged (ON) position
when the tractor is
driving in the reverse
direction. The PTO
knob must be in the
disengaged (OFF)
position when the
shift lever is placed
in REVERSE or the
electric PTO clutch
will automatically
shut off.

Operation

OPERATION

15. If the augers become jammed with a chunk of ice or a
foreign object, move the PTO into the disengaged (OFF)
position immediately and turn off the tractor’s engine
and remove the ignition key. Examine the auger area
thoroughly for damage and do NOT operate the snow
thrower attachment until any damage is repaired.

WARNING: Read, understand, and
follow all instructions and warnings
on the tractor, attachment, and in the
Operator’s Manuals before operating.
Your snow thrower attachment is capable of displacing
snow and clearing a path a width of 42 inches.

IMPORTANT: The augers are secured to the spiral
shaft with two shear bolts and hex lock nuts. If you hit
a hard foreign object or an ice jam, the snow thrower is
designed so that the bolts may shear. Two replacement
shear bolts and hex lock nuts are provided for your
convenience. Store in a safe place until needed. NEVER
replace the auger shear bolts with standard hex bolts.
Any damage to the auger gearbox or other components
as a result of doing so will NOT be covered by your snow
thrower’s warranty.

Observe the following operating instructions for efficient
snow removal.
1. Become familiar with and comfortable using all of
your tractor’s controls as instructed in your tractor’s
Operator’s Manual before operating it with the snow
thrower attachment.

WARNING
Read, understand,
and follow all
instructions and
warnings on the
tractor, attachment,
and in the Operator’s
Manuals before
operating.
IMPORTANT:
The augers are secured
to the spiral shaft with
two shear bolts and hex
lock nuts. If you hit a
hard foreign object or
an ice jam, the snow
thrower is designed
so that the bolts may
shear. Two replacement
shear bolts and hex
lock nuts are provided
for your convenience.
Store in a safe place
until needed. NEVER
replace the auger shear
bolts with standard hex
bolts. Any damage to
the auger gearbox or
other components as a
result of doing so
will NOT be covered
by your snow
thrower’s warranty.

2. Make certain the correct weight (and volume) of
motor oil in is your tractor’s engine as instructed in
the engine Owner’s Guide packed with the tractor’s
Operator’s Manual.

16. Whenever possible, discharge snow downwind.
17. Do NOT attempt to remove ice or hard-packed frozen snow.
18. When the tractor (with the snow thrower attachment
mounted) is not in service, use the lift lever to lower
the auger housing assembly to the ground to relieve
strain on the tractor’s front end between uses.

3. Always operate the snow thrower with the tractor’s
engine at maximum RPM (full throttle).
4. NEVER override any safety features on either your
tractor or the snow thrower attachment.

19. Always use tire chains and rear wheel weights on your
tractor where extra traction is needed. Refer to the
table below to determine which kits will fit your tractor
(tire dimensions are can be found on the sidewalls of
your tractor’s tires).

5. Make certain that all nuts, bolts, and hardware are
fastened securely and tight on both the tractor and
the snow thrower attachment prior to use.
6. Make certain snow thrower is assembled
properly and mounted to the tractor as instructed
in this manual.

20. Use drift cutters to aid in displacing snow through
deep, drifted areas.

8. Test all controls (tractor PTO, snow thrower lift
handle, chute tilt lever & chute crank) for smooth
operation prior to operating snow thrower in snow.

Attachments & Accessories
Garden Tractors

9. Make all adjustments (i.e. skid shoes, lift latch)
before operating your snow thrower attachment.
Follow instructions in the Adjustments section of this
manual when doing so.

23” x 9.5” tires
22” x 7.5” tires

Lawn Tractors

10. Engage the tractor’s PTO to activate power to the
augers and impeller BEFORE driving the tractor
forward and into snow.

20” x 10.0” tires
20” x 8.0” tires
18” x 9.5” tires
18” x 6.5” tires

11. Keep your tractor’s ground-speed slow. The slower
your tractor is traveling, the more effectively the
snow thrower attachment can displace snow.
12. Adjust ground speed for snow conditions and
become familiar with different snow applications.
Your snow thrower attachment will operate differently
in wet heavy snow than it will it light, fluffy snow.
13. Overlap a previously cleared path when necessary
(deep snow) so as not to overload the auger housing
with snow.
14. NEVER drive the tractor into a snow bank. The
snow thrower attachment is not a dozer plow. The lift
linkage and/or the snow thrower drive system can
be damaged as a result of “plowing” with the snow
thrower attachment.

OEM-190-964
OEM-190-974

OEM-190-916
OEM-190-658
OEM-190-657
OEM-190-664

Weight Kit Number

All Garden Tractors OEM-190-784
All Lawn Tractors 19A-218-000

Drift Cutter Kit Number
All Tractors

OEM-390-679

NOTE: None of the kits in the table are included as
standard equipment with snow thrower attachment OEM190-032 and 190-032-101. Call our Customer Support
Department as instructed on page 2 of this manual for
availability and information regarding these kits.

Making Adjustments

Lift Cable

Hex Nuts

WARNING: Never attempt to make any
adjustments while the engine is running,
except where specified in the Operator’s
Manual. Place tractor on a firm and
level surface. Place the PTO in the disengaged (OFF)
position, set the parking brake, shut engine off, and
remove key to prevent unintended starting.

Adjustments

Lift Adjustment
If the lift index rod doesn’t latch securely or the pivot
release has too much slack in it, an adjustment can be
made as follows:
1. Loosen the upper hex nut a few turns, then tighten the
lower hex nut to shorten the cable length. See Fig. 11-1.
Lift Index Rod

2. Loosen the lower hex nut a few turns, then tighten the
upper hex nut to lengthen the cable. See Fig. 11-1.

WARNING

Figure 11-1

Lower Chute Crank
Support Bracket Adjustment
If the spiral at the base of the lower chute crank isn’t fully
engaging with the notches in the lower chute assembly,
the support bracket can be adjusted inward or outward as
follows:
1. Loosen, but do NOT remove the two hex nuts which
secure the support bracket to the snow thrower
housing. See Fig. 11-2.

Spiral

2. Adjust the support bracket inward or outward so that
the spiral is fully engaged in the notches on the chute
before retightening the hex nuts.

Hex Nuts

Skid Shoe Adjustment
The space between the shave plate and the ground can
be adjusted by repositioning the skid shoes found on
either side of the snow thrower’s auger housing. For close
snow removal, place skid shoes in the low position. Use
a middle or high position when the area to be cleared is
uneven.
IMPORTANT: It is NOT recommended that this snow
thrower be operated on a gravel surface, as loose stones
can be easily picked up and thrown by the machine. If
you must operate on a gravel surface, ALWAYS adjust the
skid shoes into the HIGH position to allow the shave plate
maximum clearance.

Support
Bracket
Figure 11-2

Adjust skid shoes as follows:
1. Loosen, but do NOT remove, the three hex nuts which
fasten the skid shoe to the auger housing.
See Fig. 11-3.

Skid Shoe

2. Raise or lower the skid shoe to desired position.
NOTE: Make certain the entire base of both skid shoes
are against the ground to avoid uneven wear on the skid
shoes. When one side does wear out, the skid shoes are
reversible.
Hex Nut

3. Retighten the hex nuts loosened earlier.
4. Repeat this adjustment on the skid shoe found on the
opposite side of the snow thrower.

Figure 11-3

Never attempt
to make any
adjustments while
the engine is running,
except where
specified in the
Operator’s Manual.
Place tractor on a
firm and level
surface. Place
the PTO in the
disengaged (OFF)
position, set the
parking brake,
shut engine off,
and remove key
to prevent
unintended starting.

Maintenance

Lube Spiral
and Chute Base

WARNING: Before lubricating, repairing, or inspecting, place tractor on a
firm and level surface. Place the PTO
in the disengaged (OFF) position, set
the parking brake, shut engine off, and remove key
to prevent unintended starting.

Lubrication of
Chute Directional Control
The spiral on the end of the lower chute crank, the base
of the discharge chute itself and the joint blocks which
connect the lower and upper chute cranks should be
lubed with multi-purpose automotive grease once a
season. See Fig. 12-1.

Joint Block

WARNING
Before lubricating,
repairing, or
inspecting, place
tractor on a firm
and level surface.
Place the PTO in
the disengaged
(OFF) position, set
the parking brake,
shut engine off, and
remove key to prevent
unintended starting.

Figure 12-1

Auger Shaft
1. At least once a season, remove the shear bolts on
the auger shaft. Oil or spray lubricant inside and
on the plastic bearings on the shaft and near the
holes where the shear bolts were removed before
reattaching them. See Fig. 12-2.

Shear Pin

Spacers

Figure 12-2

Bearing

BB
6

Part List:

Snow
Thrower
Attachment

14
7

16
9

18
12

17
8
2

11
10

For parts and/or
accessories
please call
1-800-800-7310, or
1-330-220-4683.

www.mtdproducts.com
15

REF

PART No.

DESCRIPTION

REF

PART No.

DESCRIPTION

736-3072

Flat Washer, .38 x .93 x .11

741-0919

Ball Bearing

710-0151

Hex Cap Screw, 3/8-24 x 2

750-1096

Spacer

710-0521

Hex Cap Screw, 3/8-16 x 3

619-0044

Deck Spindle Housing

711-0242

Spacer

756-0999

Deck Pulley 7”

712-0241

Hex Nut, 3/8-24

756-1173

Pulley 3.75”

732-0978

Extension Spring, .620 x 5.62

738-0976

Spindle Shaft

736-0169

Lock Washer, 3/8

756-0627D

Idler Pulley 3.50 dia.

756-0487

Idler pulley, 4” Diameter

738-0347

Shoulder Spacer, .625 x .169

784-5727

Idler Pivot Arm

712-0417

Flange Nut 5/8-18

712-0417

Flange Nut 5/8-18

NOTE:
For painted parts, please
refer to the list of color
codes below. Please add
the applicable color code,
wherever needed, to the
part number to order a
replacement part.
For instance, if a part
numbered 700-xxxx is
painted powder black, the
part number to order would
be 700-xxxx-0637.
Yardman Green - 0665
Black - 0637

1
6

16
2
52

5
8

4
3

7
74

57
58

54
61

14
22

28
33

85
87

100
30

38
43
33

32
32

34
39

46
64

91
94

C
49

23 29

100

68
66
44

73
4
67

65
37

REF

PART No.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49

720-04039
784-5604A
731-1313C
712-04063
603-0302
710-0262
736-0451
741-0475
735-0234
747-0697
736-0242
750-04467
714-0507
784-5149
747-1201
746-1108
746-1109
715-0138
720-0201A
726-0100
747-04400
715-0129
611-0132A
783-0880C
783-0879C
683-04150
710-0805
710-0964A
710-3008
714-04061
712-0386A
712-3000
712-3022
714-0470
714-0474
716-0102
784-0402
736-0272
736-0366
736-0452
783-1014A
738-0234
741-0170
756-1181A
747-1192
783-0876
783-0877
783-0878
783-1274B

Knob
Chute Tilt Handle
Chute Tilt Cable Guide
Nylon Hex Lock Nut, 5/16-18
Chute Tilt Bracket Assembly
Carriage Bolt, 5/16-18 x 1.5
Saddle Washer, .32 x .93
Plastic Bushing
Rubber Grommet , .44 x .94 x .5
Eye Bolt
Bell Washer, .340 x .872
Support Chute Tube
Cotter Pin, 3/32 x .75
Joint Block Assembly
Chute Crank Rod, .375 x 33
Chute Cable, 62”
Chute Cable w/ Clip, 62”
Rolled Pin, 1/8 x .63
Crank Knob
Push Cap, 3/8 ID
Rod, .375 x 11.375
Spirol Pin, .125 x .82
Rod Assembly
RH Support Plate Assembly
LH Support Plate Assembly
Lift Bracket Assembly
Hex Cap Screw, 5/16-18 x 1.50
Hex Cap Screw, 5/8-18 x 1.31
Hex Cap Screw, 5/16-18 x .75
Quick Release Pin
Slotted Hex Nut, 5/8-18
Hex Lock Nut, 3/8-16
Hex Lock Nut, 1/2-13
Cotter Pin, 1/8 x 1.25
Cotter Pin, .125 x .75
Snap Ring
Skid Plate
Flat Washer, .51 x 1.0 x .060
Flat Washer, .64 x 1.12 x .125
Bell Washer, .396 x 1.14 x .095
Drive Mounting Bracket
Shoulder Screw, .5 x .29, 3/8-16
Flange Bearing w/ Flats
Drive Pulley, 7”
Rod, 1/2 x 11.55
Link, 5.875
Link, 15.4
Link, 13.35
Heat Shield

790-00110

Snow Thrower Lift Bracket

710-1268

Hex Index Washer Screw #10-16

710-3143

Pan Phillips Screw, #10-24 x .75

REF

PART No.

DESCRIPTION

53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70

710-3180
715-0114
720-0274
725-0157
732-0306
736-0140
736-0400
746-1103A
747-1203
750-1221
05931A
703-2736
710-0514
710-3251
712-04065
714-0122
714-0126
717-1714A

Hex Cap Screw, 5/16-18 x 1.75
Heavy Duty Spirol Pin, 1/4 x 1.5
Handle Grip
Cable Tie
Compression Spring
Flat Washer, .385 x .62 x .063
Flat Washer, .194 x .62 x .063
Lift Cable, 42” w/ Trigger Control
Lift Index Rod
Lift Handle Tube
Bearing Housing, 1.85 ID
Belt Cover
Hex Cap Screw, 3/8-16 x 1.0
Socket Head Cap Screw
Flange Lock Nut, 3/8-16
Square Key, 3/16 x .75
Hi-pro Key, 3/16 x .75
Right Angle Drive

71
72
73
74

718-0691
741-0309
747-1257
712-3010

Coupling
Flange Ball Bearing, .75 x 1.85
Belt Keeper Rod
Flange Nut, 5/16

618-0411

Spindle Assembly

683-04210

Pulley Mounting Bracket

684-0149

Double Idler Bracket Assembly

710-0347

Hex Cap Screw, 3/8-16 x 1.75

710-04511

Pin 5/16-18

710-1260A

Carriage Bolt, 5/16-18 x .62

711-0310

Clevis Pin, .5 x 1.18

711-1000

Belt Keeper Pin

712-04064

Nylon Hex Lock Nut, 1/4-20

712-04100

Wing Nut 5/16-18

714-0145

Click Pin, .092 x 1.64

714-0147

Internal Cotter Pin, .125 x 1.75

730-3000

Reflector

732-04237

Extension Spring .50 x 12.00

732-0594A

Extension Spring .91 x 7.33

736-0192

Flat Washer, .531 x .93 x .09

736-3072

Flat Washer, .38 x .93 x .11

738-0145

Shoulder Screw, 3/8-16

738-0347

Shoulder Spacer, .625 x .169

749-1103

LH Support Tube

749-1104

RH Support Tube

754-0125A

V-Belt

754-0498

V-Belt

756-0627D

Idler Pulley 3.50 dia.

783-1291

Idler Bracket

100

738-0143

Shoulder Bolt

12
Part List:

Snow
Thrower
Attachment

For parts and/or
accessories
please call
1-800-800-7310, or
1-330-220-4683.

www.mtdproducts.com

52
61
58

15
46

54
50

62
44

52
57

A
9
51
2
16
9
63

10
20
15

7
41
6

38
25

37
36

A
7

30
27

11
18

REF

PART No.

DESCRIPTION

REF

PART No.

DESCRIPTION

618-04315

Auger Gear Box (Incl. Ref. 23-41)

721-0327

Grease Seal

684-0158

Impeller Assembly, 12”

736-0351

Flat Washer, .76 x 1.5 x .030

684-0148

Housing Assembly

736-0369

Flat Washer, .508 x 1.0 x .020

703-2734

Housing Brace Bracket

736-0617

Thrust Washer, .75 x 1.25 x .0615

684-04163

LH Spiral Auger

741-0150

Thrust Bearing, .75 x 1.25 x .078

684-04164

RH Spiral Auger

748-0108

Flange Bearing, .503 x .75

710-0157

Hex Cap Screw, 5/16-24 x .75

741-0700

Flange Bearing, .75 x 1.0 x .59

710-0260A

Carriage Bolt, 5/16-18 x .62

721-0179

Grease Seal

710-0276

Splined Carriage Screw

684-0061

Chute Crank Assembly

710-0726

Self Tapping Screw

703-2735A

Chute Crank Bracket

714-04040

Bow-Tie Cotter Pin

705-5226

Chute Reinforcer

712-3010

Hex Nut, 5/16-18

710-0276

Splined Carriage Screw

712-3057

Hex Nut, 5/16-24

710-0262

Carriage Bolt, 5/16-18 x 1.5

715-0114

Spirol Pin, 1/4 x 1-1/2

710-04071

Carriage Screw, 5/16-18 x 1.0

736-0231

Flat Washer, .344 x 1.125 x .12

710-0703

Screw, 1/4-20 x .75

736-0242

Bell Washer, .340 x .872

710-0896

Hex Index Washer Screw

741-0245

Hex Flange Bearing, .75 ID

710-3015

Hex Cap Screw, 1/4-20 x .75

741-0493A

Flange Bushing, .80 x .91

712-04064

Nylon Hex Lock Nut, 1/4-20

784-0396A

Skid Plate Bracket, 42”

712-04063

Nylon Hex Lock Nut, 5/16-18

784-5038B

Slide Shoe

715-0129

Spirol Pin, .125 x .82

711-0469

Spacer, .75 x .125 x .5

731-0851A

Chute Flange Keeper

784-5618A

Hex Bearing Housing, 1.0

731-1300E

Lower Chute

618-0123A

RH Reducer Housing

731-1320

Upper Chute

618-0124A

LH Reducer Housing

731-1379D

Adapter Chute

703-2733A

Housing Brace Plate

731-1313C

Chute Tilt Cable Guide

710-0642

Self Tapping Screw, 1/4-20 x .75

741-0475

Plastic Bushing

711-04468

Spiral Axle, 41.5”

784-5149

Joint Block Assembly

714-0161

Hi-Pro Key, 3/16 x 5/8

784-5594

Cable Bracket

715-0143

Spring Spirol Pin, .25 x 1.25

784-5647

Chute Crank Bracket

717-0528A

Worm Gear, 20-tooth

712-3004A

Flange Lock Nut, 5/16-18

717-3320

Worm Shaft

731-04870

Spacer 1.25 x .75 x 1.00

718-0513

Thrust Collar

731-1086A

Sleeve .758 x 1.00 x 2.70

721-0325

Grease Plug

738-04124

Shear Pin, .25 x 1.50

12
Part List:

Snow
Thrower
Attachment

For parts and/or
accessories
please call
1-800-800-7310, or
1-330-220-4683.

www.mtdproducts.com

MANUFACTURER’S LIMITED WARRANTY FOR

The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the United States
and/or its territories and possessions, and by MTD Products Limited
with respect to new merchandise purchased and used in Canada and/
or its territories and possessions (either entity respectively, “MTD”).
“MTD” warrants this product (excluding its Normal Wear Parts and
Attachments as described below) against defects in material and
workmanship for a period of one (1) year commencing on the date
of original purchase and will, at its option, repair or replace, free of
charge, any part found to be defective in materials or workmanship.
This limited warranty shall only apply if this product has been
operated and maintained in accordance with the Operator’s Manual
furnished with the product, and has not been subject to misuse,
abuse, commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of other
peril or natural disaster. Damage resulting from the installation or use
of any part, accessory or attachment not approved by MTD for use
with the product(s) covered by this manual will void your warranty as
to any resulting damage.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: batteries, belts, blades, blade adapters, tines, grass bags,
wheels, rider deck wheels, seats, snow thrower skid shoes, friction
wheels, shave plates, auger spiral rubber and tires.
Attachments — MTD warrants attachments for this product against
defects in material and workmanship for a period of one (1) year,
commencing on the date of the attachment’s original purchase or
lease. Attachments include, but are not limited to items such as:
grass collectors and mulch kits.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service dealer.
To locate the dealer in your area:
In the U.S.A.
Check your Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-800-800-7310, 1-330-2204683 or log on to our Web site at www.mtdproducts.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following
cases:
a. Log splitter pumps, valves, and cylinders have a separate oneyear warranty.

b. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
c. Service completed by someone other than an authorized service
dealer.
d. MTD does not extend any warranty for products sold or exported
outside of the United States and/or Canada, and their respective
possessions and territories, except those sold through MTD’s
authorized channels of export distribution.
e. Replacement parts that are not genuine MTD parts.
f. Transportation charges and service calls.
g. MTD does not warrant this product for commercial use.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose, applies after
the applicable period of express written warranty above as to the
parts as identified. No other express warranty, whether written or
oral, except as mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product, shall
bind MTD. During the period of the warranty, the exclusive remedy
is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. MTD shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn
care services or for rental expenses to temporarily replace a
warranted product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
In no event shall recovery of any kind be greater than the amount of
the purchase price of the product sold. Alteration of safety features of
the product shall void this warranty. You assume the risk and liability
for loss, damage, or injury to you and your property and/or to others
and their property arising out of the misuse or inability to use the
product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
IMPORTANT: Owner may be required to present proof of purchase to
obtain warranty coverage.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100167 REV. A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract, Print high-res
XMP Toolkit                     : 3.1.1-111
About                           : 6cadc1e6-aed0-11da-b6a5-984e20bd5f7d
Create Date                     : 2007:11:08 10:53:56-05:00
Metadata Date                   : 2007:11:08 10:54:11-05:00
Modify Date                     : 2007:11:08 10:54:11-05:00
Creator Tool                    : Adobe InDesign CS2 (4.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8226 bytes, use -b option to extract)
Instance ID                     : uuid:1a4acf37-1896-4b86-bbc9-756b4f4a3fff
Document ID                     : adobe:docid:indd:633c81d9-dec0-11db-a67a-a4d49cbc0d33
Rendition Class                 : proof:pdf
Derived From Instance ID        : 67539f03-7f0d-11db-a434-f0abeb2949e3
Derived From Document ID        : adobe:docid:indd:0453bad4-b726-11d9-969a-d1fe4cc75c48
Manifest Link Form              : ReferenceStream
Manifest Placed X Resolution    : 72.00
Manifest Placed Y Resolution    : 72.00
Manifest Placed Resolution Unit : Inches
Manifest Reference Instance ID  : uuid:f403aff4-8d5d-496a-9977-96fd2cf8e3c8
Manifest Reference Document ID  : uuid:5a074916-1c8c-4f81-9e1d-d1cc9f789e68
Format                          : application/pdf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Page Count                      : 24
Creator                         : Adobe InDesign CS2 (4.0)

EXIF Metadata provided by EXIF.tools

MTD OEM 190 032 User Manual To The A230627a 0322 67a4 Dd5c A8569032f7db

Navigation menu

Versions of this User Manual:

Views

Navigation