MUNIC 4G1VZLV6 Telematics embedded system User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3582458
Application ID	3OKShpYhcfqH6jxZCCr0Fw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	208.85kB (2610611 bits)
Date Submitted	2017-09-27 00:00:00
Date Available	2018-03-26 00:00:00
Creation Date	2017-09-08 13:49:44
Producing Software	doPDF Ver 7.2 Build 373 (Windows XP Professional Edition (SP 3) - Version: 5.1.2600 (x86))
Document Lastmod	2017-09-27 09:40:42
Document Title	User manual

C4D-4G1VZL_V6 - INSTALLATION GUIDE
V 1.2
08/09/2017
Table of contents
Preface ...................................................................................................................................3
Warnings and notices ............................................................................................................3
FCC Regulations .................................................................................................................... 3
FCC RF Exposure Information (SAR) ...................................................................................... 4
1. Hardware features .............................................................................................................5
2. Hardware description ........................................................................................................6
2.1. External view ...............................................................................................................6
2.2. Internal view ...............................................................................................................6
2.3 OBD connector pin out ...............................................................................................7
3. Preparing/installing the device ..........................................................................................8
3.1. Open the device to insert a SIM card ........................................................................8
3.2. Properly close the device ............................................................................................9
3.3. Install the OBD Dongle ............................................................................................ 11
4. LED sequences................................................................................................................. 11
5. Support ............................................................................................................................ 11
Preface
The information contained in this installation guide is subject to changes in order to improve the reliability,
design or features without prior notice. Mobile Devices Ingénierie reserves the right to make changes in the
content without obligation to notify any person or organisation of such changes or improvements. Mobile
Devices Ingénierie can in no event be held liable for technical or editorial errors or omissions herein, nor for
incidental, special or consequential damages from the furnishing, performance or use of this installation
guide.
Please contact our technical support for current updates and supplemental information concerning the use
and operation of this or other Mobile Devices Ingénierie products.
Warnings and notices
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
Please read the installation guidelines, as well as the safety and operating instructions before operating your
device. Follow all instructions and heed all warnings in the installation guide.
There is a risk of explosion if the battery is replaced by a wrong battery type. Please discard empty battery
according to local regulations.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
FCC RF Exposure Information (SAR)
This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission of the United States.
During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency
bands, and placed in positions that simulate RF exposure in usage near the body with the separation of 15
mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the while
operating can be well below the maximum value. This is because the device is designed to operate at
multiple power levels so as to use only the power required to reach the network. In general, the closer you
are to a wireless base station antenna, the lower the power output.
The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6W/kg.
The FCC has granted an Equipment Authorization for this model device with all reported SAR levels
evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is
on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after
searching on FCC ID: A6G-4G1VZLV6.
For this device, the highest reported SAR value for usage near the body is 0.64 W/kg.
While there may be differences between the SAR levels of various devices and at various positions, they all
meet the government requirement.
SAR compliance for body operation is based on a separation distance of 15mm between the unit and the
human body.
1. Hardware features
OBD Dongle
Performance
Power supply
Processor
RAM
NAND Flash
External power supply range
External voltage
measurement
Li-pol battery
Modem
Modem antenna
GNSS receiver
GNSS antenna
USB (2.0 Host)
3D Accelerometer
3 axis Gyroscope
OBD protocols
Additional CAN interface
Connectors
Cortex A5 - 500MHz
128 Mbytes
256 Mbytes
8-18V
●
450mA.h
Communication
4G Cat1verizon data module (LE910-SVL)
Internal
Positioning
U-blox M8 (GPS, GLONASS, BeiDou)
Internal
Interface & Telematics features
powered (100mA on 5V minimum) optional
±2g, ±4g, ±6g, ±8g, ±16g
Optional, please contact us
CAN, KWP2000, VPW, PWM
Optional, please contact us
Environmental
OBD connector
Mini USB
Operating temperature *
-25/+60°C
Dimensions
With OBD connector: 27x60,5x49,5 mm
Without OBD connector: 27x48x49,5 mm"
SIM card
slot
* Please read warnings section at the beginning of the installation guide
2. Hardware description
2.1. External view
1.
2.
3.
ODB connector
microUSB connector
LED
2.2. Internal view
4.
5.
6.
7.
Modem antenna
GNSS antenna
SIM holder
Internal battery*
* Please read warnings section at the beginning of the installation guide
2.3 OBD connector pin out
Pin #
10
14
15
16
Comment
J1850+ (PWM/VPW)
Chassis ground
Signal ground
CAN High
K line
J1850- (PWM)
CAN low
L line
Battery voltage
3. Preparing/installing the device
3.1. Open the device to insert a SIM card
3.2. Properly close the device
First, check that the hole of the electronic card is correctly inserted in the plastic part.
If it’s not inserted proceed as shown below.
GOOD
Second, insert the GPS antenna as shown below.
NOT GOOD
Third, check that the micro USB port is correctly inserted on its place.
If it’s not inserted proceed as shown below.
GOOD
Finally, insert the battery and place the screw.
NOT GOOD
3.3. Install the OBD Dongle
Connect the OBD Dongle on your vehicle OBD connector.
4. LED sequences
The Dongle has a two-coloured LED, green and red.
When both colours are brightened, you can see an orange light.
Sequence
Green LED
Meaning
No Modem
/No GNSS
No Modem
/Fix GNSS
Modem OK
/No GNSS
Modem OK
/Fix GNSS
3 times (50ms ON/100ms OFF)
3550ms OFF
2 times (50ms ON/100ms OFF)
3700ms OFF
1 time (50ms ON/100ms OFF)
3850ms OFF
2000ms ON
2000ms OFF
Sequence
Dongle OFF
Red LED
Meaning
OFF
Ext. Power/Run
ON
Shutdown/Hibernate
Idle/Sleep
30ms ON / 1 s OFF
30ms ON / 1 s OFF
5. Support
For all questions not related in this installation guide, please contact the support team by email at
support@mobile-devices.fr

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Create Date                     : 2017:09:08 13:49:44+01:00
Modify Date                     : 2017:09:27 09:40:42+08:00
Producer                        : doPDF Ver 7.2 Build 373 (Windows XP Professional Edition  (SP 3) - Version: 5.1.2600 (x86))
Has XFA                         : No
Page Layout                     : OneColumn
Page Mode                       : UseNone
Page Count                      : 11

EXIF Metadata provided by EXIF.tools