Macdev Cyborg V1 02 Users Manual
2015-09-01
: Macdev Macdev-Cyborg-V1-02-Users-Manual-804553 macdev-cyborg-v1-02-users-manual-804553 macdev pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
MacDev 2004 Find us on the web at: www.macdev.net Please post warranty cards to: Users Manual Australia/New Zealand MacDev PO Box 584 Gymea, NSW AUSTRALIA 2227 USA/Canada Europe Paintball Kingdom 2407 Ansonville Rd Marshville NC USA 28103 OPB Sandgärdsgatan 20 352 30 Växjö SWEDEN Mac Developments - Australia www.macdev.net Info@macdev.net Cyborg Limited Factory Warranty The Cyborg marker is covered by the MacDev 12 month warranty against manufacturing defects. The Cyborg is guaranteed free of manufacturing defects for a period of twelve (12) consecutive months beginning immediately after purchase from a registered Cyborg retailer. If a manufacturing defect is detected, the defective part will be either repaired or replaced at no cost to the owner. The Cyborg warranty is not transferrable in the event of 2nd hand sales - the warranty may only be claimed by the original Cyborg retail purchaser. The Cyborg warranty does not cover damage due to theft, misadventure or operator error/abuse. Cyborg Users Manual Version 1.02 Copyright Mac Developments Pty. Ltd. 2003 All rights reserved No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Mac Developments Pty. Ltd. MacDev, Cyborg, Conquest, Gladiator, MatchStick and Sonic are all registered trademarks of Mac Developments Pty Ltd. Statement of Liability Mac Developments Pty. Ltd. Makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability or fitness for a particular purpose. The information in this document is subject to change without notice. Mac Developments Pty. Ltd. assumes no responsibility for its resale or safe handling. Mac Developments Pty. Ltd. assumes no responsibility for physical injury or property damage resulting from its use. Caution! This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by user and persons within range. Recommend 18 years or older to purchase. Persons under 18 must have adult supervision. READ OWNER’S MANUAL BEFORE USING. 2 To become eligible for the Cyborg Factory Warranty the purchaser must complete and return this warranty page to the MacDev representative in your area as listed over the page. To activate your warranty, this card must be completely filled out and returned within 14 days of the date of purchase. Cut here and send to MacDev for warranty - address overleaf Notice is hereby given that this manual is part of the article owned in whole by Mac Developments Pty. Ltd., known as indicated in this manual and drawings. All rights of manufacture and reproduction of such articles or any part thereof are reserved by Mac Developments Pty Ltd. Neither said article nor any part thereof may be manufactured or reproduced without the written authorization from Mac Developments Pty. Ltd. All proprietary rights and information are the sole property of Mac Developments Pty. Ltd. Full Name: _____________________________________________________ Address: _______________________________________________________ ______________________________________________________________ Country: _____________________________ Zip Code: ________________ Phone number_________________________ Email address: _________________________ Store purchased from: ____________________________________________ Date of Purchase: ___________________ Other MacDev products owned (if any): _______________________________ ______________________________________________________________ -------------------------------------------MacDev use only---------------------------------------Cyborg Serial #:_________________ Tested: _________________________ 15 MacDev 2004 Find us on the web at: www.macdev.net Please post warranty cards to: Australia/New Zealand MacDev PO Box 584 Gymea, NSW AUSTRALIA 2227 USA/Canada Europe Paintball Kingdom 2407 Ansonville Rd Marshville NC USA 28103 Introduction The Cyborg is an open bolt, electropneumatic marker designed specifically for accuracy and speed. The Cyborg is built from precision machined components manufactured on some of the most sophisticated computer controlled machinery in the world today. This high quality construction, coupled with careful design by qualified engineers, results in a fast, accurate and reliable marker. Specifications Weight: 2.1lbs Length: 9.25” (no barrel) Height: 8.66” (no air source) Width: 1.18” Calibre: 0.68” Power source: 9V battery Gas source: Compressed air/N2 only Barrel threads: Standard AutoCocker Detent threads: Standard Autococker Inline regulator: 04 Gladiator Solenoid: Custom 5-way, 5V Fire rate: true 30bps Anti chop system: CyberSense Software with IR beam eye Fire modes: Semi auto only Operating pressure: 200psi Processor speed : 12MHz (1 million trigger updates/sec) OPB Sandgärdsgatan 20 352 30 Växjö SWEDEN Proudly designed and manufactured in Australia 14 3 Getting Started Accessories Your Cyborg requires a source of Compressed air to be installed before use. The best air system to use with your Cyborg is the Conquest air system. However, thanks to the 04 Gladiator inline regulator, your Cyborg can accept air input from any air system supplying 400-900psi of compressed air (DO NOT USE CO2). Use genuine MacDev accessories or factory approved aftermarket upgrades for best results. For the latest list of approved aftermarket products visit www.macdev.net Rebuild Kit Mounting an air system Two mounting holes are provided on the base of the Cyborg grip frame for the purpose of attatching your air system. Please see your air system users manual for details on how to attatch your air system to these mounting points. The Cyborg rebuild kit contains all the most important parts of your Cyborg. This kit is good for peace of mind, especially when entering an important tournament. Connecting the gas Now that your air system is mounted, you will need to connect the gas to the base of the Gladiator inline regulator. This is best achieved using MacLine (if you are using a air system output of 400-700psi) or braided hose (700psi+). The Gladiator gas thru grip gives you a high volume chamber on the front of your gun for lower operating pressures. The grip features the 03 Gladiator milling. Your Cyborg comes from the factory with a MacLine fitting installed in the Gladiator. If you intend to use MacLine, then you can plumb your gun by pushing the MacLine from your air system into the fitting at the bottom of your Gladiator. Your Cyborg is now ready to use. Screw the barrel into the Cyborg and carefully push a paintball hopper into the feed neck. Your Cyborg is now ready to operate. Never operate your Cyborg without eye, ear, mouth and neck protection for yourself and anybody within range. If you need to change the fitting in the bottom of your Gladiator, please follow the instructions below. Unscrew the bottom cap from your Gladiator (by hand). Use a wrench to hold the Gladiator bottom cap in place as you change the air fitting (as shown below). Do not over tighten the air fitting, and use a snug wrench on the Gladiator to prevent scratching. Now screw the Gladiator bottom cap back into the inline regulator. Gas Thru Grip Conquest Air/Nitro System The Conquest air/nitro system is the highest quality compressed air delivery system available. The Conquest will deliver high volume, clean consistent air to your Cyborg in a lightweight compact unit - the ultimate accessory to your Cyborg. MatchStik Kit Your Cyborg was supplied bundled with a 2-piece MatchStik barrel. Own the 5 piece kit to allow good paint to barrel match with the barrel designed for your Cyborg. MacLine Kit The Macline kit includes 3 fittings (1 straight, 1 fixed elbow and 1 swivel elbow) as well as 1” of hose to ensure easy plumbing to any popular marker. Ram Gauge Check your LPR precisely for creep and recharge problems. Takes the guesswork out of tuning. Sonic LPR Cap and Thumb Adjuster The thumb adjuster eliminates the need for tools to adjust your velocity, while the LPR cap locks the adjuster off for tourney play as well as protecting your LPR system from paint hits. 4 13 Troubleshooting Setting the Velocity Some common difficulties are detailed in this section, for the latest troubleshooting information, please visit www.macdev.net. If you require more assistance with troubleshooting related issues, please contact your local macdev/Cyborg tech. Your Cyborg has been factory set to between 275 and 300fps. The Cyborg should be adjusted to comply with local legal velocities. The Cyborg velocity can be adjusted over the chronograph using a standard 1/8” allen wrench. First gas up your marker and check the gauge on the side (above the front grip) This gauge indicates the pressure setting of your inline regulator (Gladiator) and should be set to 200psi at all times. LED is flashing red or showing red at all times The red LED indicates a low battery alarm. Replace the battery with a fresh one. The marker is on, but will not cycle Ensure that the paint is loaded correctly. If paint is loaded correctly, deactivate the CyberSense and try to cycle the marker. If the marker cycles with the CyberSense off, then paint was not loaded correctly. Check that the trigger actuator adjustment is not set too far in or too far out (always back the adjustment out before trying to screw it in, because screwing it in too far may damage your circuit board. There is a leak from the marker Check the gauge on the side of the gun. It should be set to approximately 200psi. If the Gladiator needs adjustment, then adjust the pressure (using a 3/32” allen wrench on the bottom of the Gladiator - counterclockwise increases pressure). Then re-chrono the marker - the leak should disappear when the velocity is set correctly. If the leak will not disappear, please contact tech. support. The marker breaks paint Ensure that the top tube, bolt and barrel of your Cyborg are completely clean. Check to make sure that the paint is not too large for the Cyborg barrel. Ensure that your CyberSense is turned on and the barrel is screwed in completely. The marker shoots down under rapid fire Check to make certain that your air system is set to 400psi or above. When firing the gun ensure that the gauge on the side of the gun recharges quickly (if this recharges slowly, perform routine Gladiator inline reg maintenance). If the air system is set correctly and the gauge on the side of the gun recharges well, perform routine maintenance on the Cyborg ram and LPR. 12 Now chrono the marker, to increase the velocity turn the LPR adjuster clockwise, or turn the adjuster counter-clockwise to reduce the velocity. Never set the velocity over 300fps, or use/chrono your Cyborg without first ensuring that you and all other people in range are wearing appropriate protective clothing. Operating Your Cyborg Turning the power on and off To turn your Cyborg marker on, simply press and hold the on/off button for 2 seconds. You will see the indicator LED flash red once and hear a single soft chime. If you release the button at this point the Cyborg will be set to active mode, with CyberSense activated (at this point the indicator LED should shine green). If you have a paintball in the Cyborg ready to fire, the Cyborg will operate normally, however if you attempt to fire without a paintball in the Cyborg it will not cycle. To turn your Cyborg off, simply press and hold the on/off button until the indicator LED flashes red twice and chimes twice - then release the button. The indicator LED should extinguish. Deactivating the CyberSense Your Cyborg should always be operated with the CyberSense active. However, there are instances where it may be necessary to deactivate this function (for example if you need to fire the Cyborg without paintballs). To deactivate the CyberSense you can either: - Hold the on/off button down until the indicator LED flashes 3 times or - Change dip switch 6 to the off position 5 Fine Tuning and Customising your Cyborg Your Cyborg can be adjusted in many ways to suit your individual playing style. You can adjust the trigger feel, sensitivity and speed. Trigger Adjustment There are 3 set screws around the trigger area to use for fine tuning the trigger. The lower screw on the front of the trigger is used to adjust the length of the trigger pull - screw it clockwise to reduce the trigger pull length. The second, higher screw on the front of the trigger is used to adjust the actuation position. Screw this screw clockwise toactuate the microswitch earlier in the trigger pull. CAUTION: be cautious when adjusting this screw - adjusting the screw too far in may cause damage to your circuit board! The final adjustment screw is located on the inside top of the trigger guard winding this screw in a clockwise direction will increase the trigger pull tension. Trigger Sensitivity Adjustment The sensitivity of the trigger system can be adjusted via the dip switches located under your wrap around grip. CAUTION! Take great care when switching the dip switches - use a very small screwdriver and take care not to push downwards on the switch (only across) - damage to the dip switches can result in board malfunction. The trigger sensitivity settings are: Switch 1 Switch 2 Trigger Sensitivity ON ON Lowest OFF ON Low ON OFF High OFF OFF Highest Gladiator Inline Regulator Maintenance To keep your Gladiator working well you should clean and lubricate the piston regularly (at least every 20,000 shots or so, you may perform this maintenance more often if desired). To do this follow these easy steps: 1. Degas the Cyborg of all pressurised gas, then remove the Gladiator from the Cyborg. Unscrew the Gladiator bottomworks and put it aside. 2. Place a clean rag on the tabletop and push the piston assembly out from the top. Separate the piston from the o-ring retainer and spring washers. 3. Clean the piston and o-ring retainer of old grease using a clean rag, do not leave any lint or cotton strands on or between the o-rings. Re-apply Dow 33 to the o-rings. 4. Clean the piston bore using a Q-tip to remove all old grease. 5. Using a clean Q-tip, apply silicon grease to the piston bore. Do not over apply grease - all you need is a thin film. 6. Slide the spring washers back onto the piston and lubricate the shaft with Dow 33. Now slide the o-ring retainer back onto the shaft. 7. Slide the piston etc back into the Gladiator topworks and screw the bottom and topworks back together before re-installing the Gladiator onto your Cyborg. LPR Maintenance The LPR should be cleaned and re-lubricated at the same time as the Gladiator inline regulator. Remove the adjuster cap by unscrewing it from the LPR (counter-clockwise), and remove the spring under the adjuster. Use a pair of needle nosed pliers to remove the LPR piston. Clean and relubricate the piston bore using a q-tip then clean and re-lubricate the piston itself before replacing it back in the LPR body. Replace the LPR spring and adjuster cap. You will need to re-chrono your marker after doing this. Trigger Filter The Cyborg has a built in trigger filter to help eliminate trigger bounce. Depending on your trigger sensitivity setting, you may find it necessary to turn the filter off. Dip switch 3 is used to control the trigger filter - when switch 3 is in the “on” postion, the trigger filter is set to low (minimal filtering), conversely if switch 3 is off, the filter is in high (maximum filtering) mode. The filter is set to low as a default - you should only switch it to high if you are experiencing excessive trigger bounce. 6 11 Caring for your Cyborg The Cyborg is a very low maintenance marker, however there are some things that you can do to keep it running at optimum performance. Always use Dow 33 to lubricate your Cyborg, do not use Silicone spray or oil of any kind. Bolt Maintenance The Cyborg bolt is made from a very high quality self lubricating plastic. For this reason the bolt should always be used dry - never lubricate the bolt. During normal usage, the Cyborg bolt can become dirty. To remove the bolt, gently pull the pull pin upwards until it clicks. The bolt and pull pin should then slide freely out of the gun. Clean the bolt with a clean, dry soft cloth. If you notice scratches along the bolt, it is likely that you have not cleaned it often enough - it is a good idea to clean the bolt after evey days play, or if it gets excessive paint/dirt in it during the course of play. When replacing the bolt, it is critical to ensure that the bottom of the pull pin is located correctly in the slot on the ram inside the gun. If the bolt is incorrectly installed your Cyborg will not operate correctly and damage may result. Ram Maintenance The ram of your Cyborg does the most work of any part of the gun. For this reason the ram system needs to be kept clean and well lubricated. Before removing your ram ensure that there is no gas in the gun. First remove the bolt (as described above in bolt maintenance) and unscrew the ram cap (counterclockwise) and remove it from the gun. Then grasp the ram end and pull it out of the Cyborg. Now remove the hammer from the ram housing. Clean the old grease off the ram housing bore using a clean q-tip, and clean the old grease from the ram housing and hammer using a clean lint free cloth. Use a clean q-tip to re-lubricate the bore of the ram housing with Dow 33, and use your finger to re-lubricate the o-rings on the hammer as well as the hammer shaft. Slide the hammer back into the ram housing and re-lubricate the o-rings on the outside of the ram housing. Now your ram is ready to be replaced back into the marker - slide it back in carefully before securing it in place with the ram nut. Take care that the bolt is replaced correctly as described above in bolt maintenance. Maximum Cycle Rate The maximum cycle rate of the Cyborg can be adjusted. As long as you are using the CyberSense (paint detection) system, you will not require this setting (because your Cyborg will only fire as fast as your hopper). However, if you would like to limit the speed of Your Cyborg, you can do it by changing Dip switches 4 and 5 as shown: Switch 4 Switch 5 Maximum cycle rate ON ON 30 cycles/sec OFF ON 25 cycles/sec ON OFF 20 cycles/sec OFF OFF 17 cycles/sec Dip Switch Settings The dip switches are located under the left hand grip plate. Take great care when switching the switches as they are small and fragile. Avoid changing the switches often as careless use may cause damage. Your Cyborg is factory set with the trigger sensitivity set to highest, the trigger filter set to low, the maximum cycle rate at 30cycles/sec and the CyberSense enabled. This will give you the fastest, easiest rate of fire available - if you have no problems, do not change the dip switch settings! Dip switches 7&8 are used by the MacDev factory There is no use switching them. A switch summary is provided: Dip Switch Number Setting 1 2 3 4 5 6 ON ON - - - - Lowest sensitivity ON OFF - - - - Low sensitivity OFF ON - - - - High sensitivity OFF OFF - - - - Highest sensitivity - - ON - - - Low filter - - OFF - - - High filter - - - ON ON - 30 cycles/sec Ram maintenance can be performed as often as you like, and should be done at least every 20,000 cycles. - - - OFF ON - 25 cycles/sec - - - ON OFF - 21 cycles/sec Regulator Maintenance Your Gladiator inline regulator and LPR should be kept clean and lubricated for best results. - - - OFF OFF - 17 cycles/sec - - - - - ON CyberSense ON - - - - - OFF CyberSense OFF 10 7 Cyborg Schematic This schematic does not show all Cyborg parts. Some parts have been omitted for clarity.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2004:09:02 15:00:49+10:00 Create Date : 2003:12:26 14:31:55Z Producer : Adobe PDF Library 5.0 Creator : Adobe InDesign 2.0.1 Trapped : False Page Count : 8 Creation Date : 2003:12:26 14:31:55Z Mod Date : 2004:09:02 15:00:49+10:00 Metadata Date : 2004:09:02 15:00:49+10:00 Document ID : adobe:docid:indd:0da61b81-3754-11d8-8e97-b2f16f310c53 Version ID : 1 Rendition Class : proof:pdf Rendition Of Document ID : adobe:docid:indd:0da61b81-3754-11d8-8e97-b2f16f310c53 Rendition Of Version ID : 1 Rendition Of Rendition Class : default Format : application/pdf Title : Tagged PDF : YesEXIF Metadata provided by EXIF.tools