Mackie Art500 Users Manual Quick Start Guide

Mackie ART500 Quick Start Guide art500_qs Mackie - ART500 - Quick Start Guide

ART500 to the manual 12c63dca-5290-409d-8cf0-cbced1386a67

Mackie ART500 Quick Start Guide art500_qs Mackie - ART500 - Quick Start Guide

: Mackie Mackie-Art500-Users-Manual-436580 mackie-art500-users-manual-436580 mackie pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

Specifications

ART500

System:

Transducers:

Freq. Range (–10 dB):
50Hz-20kHz

Low Frequency:
15" (380 mm) diameter woofer

Freq. Response (±3 dB):
70Hz-17kHz

High Frequency:
2" (51 mm) compression driver,
horn loaded

Horz. Coverage Angle (–6 dB):
80° nominal
Vert. Coverage Angle (–6 dB):
60° nominal

Physical:
Enclosure:
Asymmetrical trapezoidal,
reinforced polypropylene

Directivity Factor Q (DI):
10.7 (10.3), averaged 1kHz-10kHz
System Sensitivity:
100 dB, 1W@1m
Rated Maximum SPL:
133 dB @ 1 m (3.3ft) peak
HF Protection:
Over-voltage dampening
System Input Power Rating:
500W RMS
2000W Peak
Recommended Amplifier Power:
700W RMS
System Nominal Impedance:
8 ohms

Mounting:
Lockable 1-3/8" (35mm) stand
mount
Rigging Inserts:
6 points, accepts M10 threaded
hardware
Input/Output Connectors:
2 Neutrik Speakon
Dimensions HxWxD:
29.1" x 17.9" x 14.8"
(740 mm x 454 mm x 375 mm)

Passive Speaker System
The ART500 is a full-range two-way
professional passive speaker system that
combines high power, wide bandwidth, and
the reduced weight of a special hybrid
construction for fixed-installation systems. The
15" low-frequency transducer, in combination
with a 2" titanium compression driver coupled
to an integral 80º x 60º constant directivity
polynomial horn, form an extremely powerful
package for any small to medium-sized sound
reinforcement application.
It features dual Neutrik Speakon® input
and output connectors for cascading multiple
speakers. The passive crossover is designed
to reduce heat dissipation and optimize the
power response of the loudspeaker.
The enclosure is constructed of highstrength polypropylene and multilayer wood,
with M10 threaded inserts on all four sides for
rigging, and an integral locking 1-3/8" socket
in the bottom for mounting on a standard
speaker stand.

Net Weight:
72.7 lb (33.0 kg)

Crossover Frequency and Slope:
1.8kHz; 24 dB/octave

Safety First!
Before connecting and using the
equipment, please read this Quick-Start Guide
carefully and keep it for future reference.

HF Protection:
Dynamic

WARNING! This equipment has been
designed to be installed by qualified
professionals only! There are many factors to
be considered when installing professional
sound reinforcement systems, including
mechanical and electrical considerations, as
well as acoustic coverage and performance.
Mackie Industrial strongly recommends that
this equipment be installed only by a
professional sound installer or contractor.
industrial@mackie.com
16220 Wood-Red Road NE Woodinville, WA 98072
TEL +888.337.7404, FAX +425.487.4337
UK +44.1268.570.808, FAX +44.1268.570.809 +industrial@rcf-uk.com
ITALY +39.0522.354.111, FAX +39.0522.332.294 +industrial@rcf.it
FRANCE +33.3.8546.9160, FAX +33.3.8546.9161 +industrial@rcf.fr
GERMANY +49.2572.96042.0, FAX +49.2572.96042.10 +industrial@mackie.de
Part No. 910-171-20 Rev. A 2/00
© 2000 Mackie Industrial. All Rights Reserved. Printed in the USA.

Quick-Start Guide

ART 500

Rear Panel Features

Connections

1. INPUT is a Neutrik Speakon connector for
connecting a speaker-level signal.

The Speakon connectors use the following
wiring standard:
Pin 1+ = Signal (+)
Pin 1– = Ground (–)

SPEAKER SYSTEM

CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL • MADE IN ITALY • COPYRIGHT ©1999
THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "MACKIE INDUSTRIAL", & THE "RUNNING MAN" FIGURE

2. OUTPUT is a Neutrik Speakon connector
that is paralleled with the INPUT jack, for
daisy-chaining speakers together.

1–
1+

COLD
HOT

1–
1+

2+
2–

Installation
A 1-3/8" (35mm) socket is provided in the
bottom of the cabinet for mounting the
loudspeaker on a speaker stand.
The ART500 can be suspended with
approved rigging hardware. Always use at
least two M10 threaded inserts located
on opposite sides of the enclosure. The
speaker must be positioned so that the
weight of the enclosure is equally distributed
over the two inserts.

SERIAL NUMBER
(SIGNAL)1+

2– (N.C.)
ALL CONTACTS
PARALLEL WIRED

(GROUND)1–

MANUFACTURING DATE

2+ (N.C.)

IMPEDANCE: 8

POWER: 500W

WARNING: Never attempt to suspend the
ART Series loudspeakers by their handles.
Consult a professional rigger or structural
engineer prior to suspending loudspeakers
from a structure not intended for that use.
Always know the working load limit of the
structure supporting the loudspeaker array.
Always make sure that the rigging hardware
minimum rating is at least five times the
actual load.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2000:03:11 20:33:10
Producer                        : Acrobat Distiller 4.0 for Macintosh
Modify Date                     : 2000:12:04 16:58:04-07:00
Title                           : ART500 Quick-Start Guide
Subject                         : Mackie Industrial ART500 Passive Speaker System
Author                          : David Franzwa
Keywords                        : ART500, Mackie Industrial, Passive Speaker, Installed Sound, Contractor
Page Count                      : 2

EXIF Metadata provided by EXIF.tools