Mackie M2000 Users Manual M Series High Efficiency Power Amplifiers Owner's
Mackie M1400 M-Series Owner's Manual mseries_om Mackie - M1400 - M-Series Owner's Manual
Mackie M1400i M-Series Owner's Manual mseries_om Mackie - M1400i - M-Series Owner's Manual
M4000 to the manual 87174237-d0b9-41c0-8d76-1f7ec8315409
Mackie M1400 M-Series Owner's Manual mseries_om Mackie - M1400 - M-Series Owner's Manual
Mackie M1400i M-Series Owner's Manual mseries_om Mackie - M1400i - M-Series Owner's Manual
2015-02-02
: Mackie Mackie-M2000-Users-Manual-436597 mackie-m2000-users-manual-436597 mackie pdf
Open the PDF directly: View PDF .
Page Count: 28
![](asset-1.png)
M-SERIES
HIGH EFFICIENCY POWER AMPLIFIERS
M•2000
M•3000
M•4000
OL
-3
-6
-9
-20
SIG
OL
-3
-6
-9
-20
SIG
2
INTERNAL
STATUS
INTERNAL
STATUS
PROTECT
SHORT
OVER TEMP
PROTECT
SHORT
OVER TEMP
OO
MAXMAX
OO
1
M.4000
POWER
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-2.png)
2
M-Series
M-Series
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
WARNING — The speaker output terminals, marked with ( ) can
pose a shock hazard to the user. Speaker cables should be purchased
ready-made from a qualified supplier. If the user decides to construct
speaker cabling (using the instructions provided later in this manual), it is
recommended that the construction be reviewed by a qualified electrician.
15.
This apparatus has been designed with Class-I construction and must
be connected to a mains socket outlet with a protective earthing con-
nection (the third grounding prong).
16.
This apparatus has been equipped with a single pole rocker style AC
mains power switch. This switch is on the front panel and should
remain readily accessible to the the user. Note that when the power
switch is not in the “ON” position, the apparatus is still energized, and
internal hazardous voltages are still present.
17.
This apparatus does not exceed the Class A/Class B (whichever is
applicable)
limits for radio noise emissions from digital apparatus as
set out in the radio interference regulations of the Canadian Department
of Communications.
ATTENTION — Le présent appareil numérique n’émet pas de bruits
radioélectriques dépassant las limites applicables aux appareils numériques de
class A/de class B (selon le cas) prescrites dans le réglement sur le brouillage
radioélectrique édicté par les ministere des communications du Canada.
18.
Exposure to extremely high noise levels may cause permanent hearing
loss. Individuals vary considerably in susceptibility to noise-induced
hearing loss, but nearly everyone will lose some hearing if exposed to
sufficiently intense noise for a period of time. The U.S. Government’s
Occupational Safety and Health Administration (OSHA) has specified
the permissible noise level exposures shown in the following chart.
According to OSHA, any exposure in excess of these permissible limits
could result in some hearing loss. To ensure against potentially danger-
ous exposure to high sound pressure levels, it is recommended that all
persons exposed to equipment capable of producing high sound pres-
sure levels use hearing protectors while the equipment is in operation.
Ear plugs or protectors in the ear canals or over the ears must be worn
when operating the equipment in order to prevent permanent hearing
loss if exposure is in excess of the limits set forth here.
Important Safety Instructions
WARNING — To reduce the risk of fire or
electric shock, do not expose this apparatus
to rain or moisture.
Duration Per Day Sound Level dBA, Typical
In Hours Slow Response Example
8 90 Duo in small club
6 92
4 95 Subway Train
3 97
2 100 Very loud classical music
1.5 102
1 105 Tami screaming at Adrian about deadlines
0.5 110
0.25 or less 115 Loudest parts at a rock concert
PORTABLE CART WARNING
Carts and stands - The
Component should be used
only with a cart or stand
that is recommended by
the manufacturer.
A Component and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the Component and cart
combination to overturn.
CAUTION AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
ATTENTION: POUR EVITER LES RISQUES DE CHOC
ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE. AUCUN
ENTRETIEN DE PIECES INTERIEURES PAR L'USAGER. CONFIER
L'ENTRETIEN AU PERSONNEL QUALIFIE.
AVIS: POUR EVITER LES RISQUES D'INCENDIE OU
D'ELECTROCUTION, N'EXPOSEZ PAS CET ARTICLE
A LA PLUIE OU A L'HUMIDITE
The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure, that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
Le symbole éclair avec point de flèche à l'intérieur d'un triangle
équilatéral est utilisé pour alerter l'utilisateur de la présence à
l'intérieur du coffret de "voltage dangereux" non isolé d'ampleur
suffisante pour constituer un risque d'éléctrocution.
The exclamation point within an equilateral triangle is intended to
alert the user of the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Le point d'exclamation à l'intérieur d'un triangle équilatéral est
employé pour alerter les utilisateurs de la présence d'instructions
importantes pour le fonctionnement et l'entretien (service) dans le
livret d'instruction accompagnant l'appareil.
![](asset-3.png)
Part No. 0017576 Rev. A 2/06
©2006 LOUD Technologies Inc. All Rights Reserved.
3
Owner’s Manual
Owner’s Manual
Don’t forget to visit our website at www.mackie.com for more
information about this and other Mackie products.
R
Table of Contents
Introduction ................................................................................................................4
Getting Started ..........................................................................................................5
Connections and Settings ........................................................................................................................5
Hookup Diagrams ......................................................................................................7
M-Series Features ....................................................................................................10
Front Panel .................................................................................................................................................10
Rear Panel ...................................................................................................................................................12
General Precautions and Considerations ..........................................................16
Rack Mounting ..........................................................................................................................................16
Thermal Considerations .........................................................................................................................16
AC Power Considerations .......................................................................................................................16
Input Wiring ...............................................................................................................................................17
Output Wiring ...........................................................................................................................................18
Appendix A: Service Information ........................................................................21
Warranty Service ......................................................................................................................................21
Troubleshooting .......................................................................................................................................21
Repair ......................................................................................................................................................... 22
Appendix B: Technical Info ....................................................................................23
M-Series Specifications ..........................................................................................................................23
M-Series Dimensions ..............................................................................................................................24
M-Series Block Diagram ........................................................................................................................26
M-Series Limited Warranty ..................................................................................27
![](asset-4.png)
4
M-Series
M-Series
Introduction
Thank you for choosing a Mackie high-efficiency
power amplifier. We appreciate your vote of confidence
for the folks in Woodinville who specialize in awesome
and affordable professional audio designs.
The Mackie M-Series power amplifiers have a wide
variety of features that set them apart from any other
amplifier in their price range.
• More Output Devices
The more output devices that are used in a power am-
plifier, the more reliably the amplifier will operate over
the long-term at high power levels into low-impedance
loads. The M-Series amplifiers typically use more output
devices for the same output power than our competitors
amplifiers. This means the output devices are required
to handle less power, thus drastically extending the life-
expectancy of our amplifiers.
• True 2-ohm Power Capability
Some amplifier manufacturers present their power
ratings into 2-ohms at 1 kHz. Because our M-Series pow-
er amplifiers use more output devices, they can provide
full-power into 2-ohms over the entire audio frequency
range, from 20 Hz to 20 kHz, all night long!
• Higher Efficiency
The M•2000 uses a highly efficient two-rail Class-H
topology, while the M•3000 and M•4000 use an even
more efficient three-rail Class-H topology. This allows
the amplifiers to run cooler, even in high-ambient
temperatures, while improving their long-term reliability.
• Lower Distortion
Our design engineers have paid particular attention
to reducing distortion in the M-Series amplifiers. From
triple darlington output stages to a fully complementary/
differential design from input to output, to the Mackie
exclusive adaptive slew Class-H switching design that
allows the amplifiers to pass the fastest transient peaks
while minimizing Class-H switching distortion. The
bottom line is the M-Series amplifiers achieve some of
the lowest distortion numbers in the business without
resorting to substantial amounts of negative feedback.
• That’s Not All!
There are plenty more features that make your selec-
tion of a Mackie M-Series power amplifier a good invest-
ment, from the Fast Recovery design pioneered in our FR
Series amplifiers, to the quiet fans and constant thermal
gradient heatsinks to dissipate heat away from the output
devices evenly and efficiently, to the extensive protec-
tion circuits designed to protect the amplifier and your
loudspeakers.
HOW TO USE THIS MANUAL
We know that many of you can’t wait to get your new
amplifier hooked up, and you’re probably not going to
read the manual first (sigh!). So the next section is a
Quick-Start Guide to help you get the amplifier set up
fast so you can start using it right away. Right after that
are the ever popular hook-up diagrams that show typical
setups for live sound applications.
Then, when you have time, read the Features Descrip-
tion section. This describes every knob, button, and
connection point on the M-Series amplifiers.
Throughout this section you’ll find illustrations with
each feature numbered. If you want to know more about
a feature, simply locate it on the appropriate illustra-
tion, notice the number attached to it, and find that
number in the nearby paragraphs.
This icon marks information that
is critically important or unique to
the M-Series amplifiers. For your
own good, read them and remember
them. They will be on the final test.
This icon leads you to in-depth
explanations of features and practi-
cal tips. While not mandatory, they
usually have some valuable nugget of
information.
More resources on our website at
www.mackie.com.
Click on Support to find answers to many of your ques-
tions. The FAQ (Frequently Asked Questions) section is
filled with answers to many of the questions our Techni-
cal Support staff has fielded over the years.
Check out the glossary for explanations of many of the
pro-audio terms used in our manuals.
Visit our forums to seek help from our online commu-
nity of Mackie users.
Please write your serial number here for
future reference (i.e., insurance claims, tech
support, return authorization, etc.)
Purchased at:
Date of purchase:
![](asset-5.png)
5
Owner’s Manual
Owner’s Manual
Getting Started
READ THIS PAGE!!
Even if you’re one of those people
who never read manuals, all we ask
is that you read this page now before
you begin using the M-Series power
amplifier. You’ll be glad you did!
IMPORTANT: The amplifier draws
its ventilation air in from the rear
and out through the front panel. It
needs plenty of fresh air to stay cool.
DO NOT BLOCK THE VENTILATION
PORTS!
Connections and Settings
1. Turn down the channel Gain controls.
2. Set the 150 Hz X-OVER switches to FULL.
3. Set the LIMIT switches ON.
4. Turn the POWER switch off.
5. Determine which AMP MODE is best for your ap-
plication.
• STEREO mode (separate left and right inputs,
separate left and right outputs) is the typical setup
for amplifying stereo signals.
• MONO mode (sometimes called Dual-Mono mode
— one mono input, two mono outputs) is for send-
ing a mono signal to two different speaker sets, with
separately-adjustable level controls.
• BRIDGE mode (sometimes called Bridged-Mono
— one mono input, one mono output) uses both sides
of the amp to double the power to one speaker set.
Note: 4 ohms is the minimum impedance you
should connect to the amplifier in BRIDGE mode (2
ohms in MONO or STEREO modes). If you connect
a lower impedance load, the SHORT LEDs may
light, putting the amplifier into PROTECT mode.
Set the AMP MODE switch accordingly.
6.
In STEREO mode, connect line-level cables from
your signal source to the M-Series amplifier’s INPUT
jacks, either XLR, TRS, or screw terminals:
• All the inputs and thru jacks for each channel
are wired in parallel.
• The balanced XLR inputs are wired
pin 2 = hot (+), pin 3 = cold (–) and
pin 1 = shield (ground).
• The 1/4" TRS inputs are wired tip = hot (+),
ring = cold (–) and sleeve = shield (ground), and
can accept either balanced (TRS) or unbalanced
(TS) cables.
• The screw terminal inputs are wired as indicated:
hot (+), cold (–), and ground (GND).
7. In MONO and BRIDGE modes, the signals appear-
ing at Channel 1 and Channel 2 inputs are summed
together to create a mono signal.
8. In STEREO and MONO modes, connect speaker
cables to the SPEAKER OUTPUTS, either binding
posts or Speakons®:
• The binding post connectors are wired red = hot
(+) and black = cold (–).
• The Speakon connectors are wired as follows:
Channel 1
pin 1+ = Ch 1 hot (+) and pin 1– = Ch 1 cold (–)
pin 2+ = Ch 2 hot (+) and pin 2– = Ch 2 cold (–)
Channel 2
pin 1+ = Ch 2 hot (+) and pin 1– = Ch 2 cold (–)
pin 2± = unused
BRIDGE
pin 1+ = hot (+) and pin 1– = cold (–)
pin 2± = unused
9. In BRIDGE mode, connect the binding post cable
like this: the hot (+) side goes to the CHANNEL 1
SPEAKER OUTPUTS red post and the cold (–) side
goes to the CHANNEL 2’s red post. Connect nothing
into the black posts.
10. Connect the other ends of the speaker cables to
your loudspeakers.
11. Plug the amplifier’s power cord into an outlet prop-
erly configured with the correct voltage for your
amplifier, and capable of delivering enough current
to reach full power.
12.
Make sure your signal source (feeding the amplifier’s
inputs) is powered up and delivering signal to the amp.
13. Turn the amplifier’s POWER switch on and verify
that the signal present (SIG) LEDs are blinking.
14. Slowly turn both Gain controls up:
You should hear the music and see the SIG and
meter LEDs flashing. If the topmost LEDs (named
OL, for OverLoad) are flashing, turn down either
the Gain controls on the amp or the source signal’s
output level controls (i.e., master faders). The point
is: The OL LEDs should only occasionally light up.
Frequent lighting of the the OL LEDs indicates that
the amplifier is being driven too hard and clipping
distortion is likely audible.
![](asset-6.png)
6
M-Series
M-Series
15. For quieter listening, it is preferable to adjust the
amplifier’s gain controls rather than the source
signal’s output level (unless you have the source’s
control all the way up!).
Other Nuggets of Wisdom
• For optimum sonic performance, the channel and
main mix faders on your mixer should be set near
the “U” (unity gain) markings. Then adjust the
amplifier’s gain control to attain the desired volume
through the loudspeakers.
• Never plug amplifier outputs into anything except
speakers (unless you have an outboard box specifi-
cally designed to handle speaker-level signals).
• Before making connections to an amp or recon-
figuring an amp’s routing, turn the amp’s level
(Gain) controls down, turn the power off, make the
changes, turn the power back on, and then turn the
level controls back up.
• When you shut down your equipment, turn off the
amplifiers first. When powering up, turn on the
amplifiers last.
• Never listen to loud music for prolonged periods.
Please see the Safety Instructions on page 2 for
information on hearing protection.
• Save the shipping box! You may need it someday,
and you don’t want to have to pay for another one.
That’s it for the “Getting Started” section. Next comes
the “Hookup” section that shows you some typical ways
that you might use the M-Series amplifier in real ap-
plications. After that, take the grand tour of the ampli-
fier, with descriptions of every knob, button, input, and
output. We encourage you to take the time to read all of
the feature descriptions, but at least you know it’s there
if you have any questions.
![](asset-7.png)
7
Owner’s Manual
Owner’s Manual
Hookup Diagrams
M-Series Power Amplifier: Biamp Connection Using Built-in X-over
This drawing shows a typical stereo hookup, connecting
two speakers to the Speakon® outputs. The Amp Mode
switch is set to STEREO, and the X-over switches are set
to FULL. The binding posts can also be used to connect
the speakers (shown as an optional connection).
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
FROM MIXING CONSOLE
MAIN OUT
Biampable Two-Way Speaker
Ch 1 and 2 on single
4-conductor
speaker cable AMP MODE SWITCH
STEREO
X-OVER SWITCHES
CH 1: LPF CH 2: HPF
1+/–
2+/–
COLD
COLD
AMPLIFIER
END
SPEAKER
END
HOT
CHANNEL 1
CHANNEL 2
1+
1–
2–
2+
1+
1–
2–
2+
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
BRIDGE
+
++
SPEAKER OUTPUTS
FROM MIXING CONSOLE
LEFT AND RIGHT MAIN OUT
AMP MODE SWITCH
STEREO
Passive Speakers (Mackie S408)
TO SPEAKERS
OPTIONAL CONNECTION USING BINDING POSTS
M-Series Power Amplifier: Stereo Mode Connection
The Channel 1 Speakon output connector
has four conductors and carries both
channels (1± is Channel 1 out and 2± is
Channel 2 out). This is ideal for driving
a biampable two-way speaker cabinet.
The Amp mode switch is set to STEREO,
Channel 1’s input is jumpered over to Channel 2 using
the Thru connector on Channel 1. The X-over switch on
Channel 1 is set to LPF while Channel 2 is set to HPF.
Channel 1 carries the low frequencies (below 150 Hz) to
the low-frequency driver, and Channel 2 carries the high
frequencies (above 150 Hz) to the high-frequency driver.
Many biampable cabinets are configured to accept both
LF and HF signals on a single Speakon connector.
![](asset-8.png)
8
M-Series
M-Series
M-Series Power Amplifier: Bridge Mode Connection
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
BRIDGE
+
++
SPEAKER OUTPUTS
FROM MIXING CONSOLE
MAIN OUT
AMP MODE SWITCH
MONO
Passive Speakers (Mackie S408)
TO SPEAKERS
OPTIONAL CONNECTION USING BINDING POSTS
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
BRIDGE
+
++
SPEAKER OUTPUTS
FROM MIXING CONSOLE
MAIN OUT
AMP MODE SWITCH
BRIDGE
Passive Speaker
(Mackie S408)
TO SPEAKER
+ –
OPTIONAL CONNECTION USING BINDING POSTS
M-Series Power Amplifier: Mono Mode Connection
![](asset-9.png)
9
Owner’s Manual
Owner’s Manual
M-Series Power Amplifier: Two Amps Using Built-in X-over
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
BRIDGE
+
++
SPEAKER OUTPUTS
FROM MIXING CONSOLE
LEFT AND RIGHT MAIN OUT
Passive Speakers (Mackie S408)
Passive Subwoofers
(Mackie S410s)
TO SPEAKERS
OPTIONAL CONNECTION USING BINDING POSTS
AMP MODE SWITCH
STEREO
X-OVER SWITCH
HPF
AMP MODE SWITCH
STEREO
X-OVER SWITCH
LPF
This drawing shows how to use the X-over switches to power a stereo two-way system without using
an external crossover. The X-over switches on Amplifier 1 are set to HPF and both channels pass
frequencies above 150 Hz to the loudspeakers.
The Thru connections pass the full-range signals on to Amplifier 2. The X-over switches on
Amplifier 2 are set to LPF and both channels pass frequencies below 150 Hz to the subwoofers.
![](asset-a.png)
10
M-Series
M-Series
M-Series Features
Front Panel
Much of the front panel of the M-Series amplifiers is
comprised of ventilation slots for expelling warm air from
the inside of the amplifier. Be sure to leave space in front
of the amplifier for proper ventilation to occur.
1. Gain Control
These knobs control the levels to the output section of
the M-Series amplifiers. You’ll notice that their travel is
detented, meaning there are 21 built-in “resting points”
so you can easily set both controls to the same level.
Usually, these controls are set all the way up.
The gain structure of the amplifier is designed so that
a +4 dBu (1.23V rms) input signal drives the amplifier
to full power into 4 ohms.
M•2000 = 525 watts/channel into 4 ohms
M•3000 = 800 watts/channel into 4 ohms
M•4000 = 1050 watts/channel into 4 ohms
This is how the sensitivity of an amplifier is defined
(the input voltage required to attain maximum output
power into a specified load impedance). In this case,
it
equates to a voltage gain of 31.4 dB for the M•2000,
33.3 dB
for the M•3000, and 34.4 dB for the M•4000).
With the Gain control all the way up (fully clockwise),
the input sensitivity is 1.23V, which works well with
professional equipment operating at a nominal +4 dBu
level.
On the other hand, you may want your listening level
to be quieter than the M-Series amplifier’s maximum
level. For instance, if you’re using the amplifier as a
control room amp, and your control room is the size of a
telephone booth, you’ll probably never want to hear the
amp at its maximum level.
You can set the Gain controls as low as you like. How-
ever, reducing the Gain controls requires an increased
input level to reach full power at the amplifier’s output.
Like all amplifier controls, you’ll typically determine
the optimal settings during installation or sound check,
then leave them alone, using your signal source (usually
a mixer) to control listening levels as you work. Or play.
2. Meters
The M-Series amplifier’s meters indicate the relative
output level of the amplifier referenced to full power.
The numbers next to the meter’s LEDs are in dB below
full power.
Ideally, the –20, –9, –6, and –3 LEDs will light and
blink at normal signal levels, while the OL LED may
flicker occasionally during peak moments.
OL is short for Overload. Overloading, or clipping,
occurs
when the output voltage no longer linearly fol-
lows the input voltage and simply stops. This causes a
sine wave to “square off,” or get “clipped off.” Thus, the
term clipping. Fear not — this scenario is quite unlike-
ly.
Even with the Gain controls fully up, the M-Series
amplifier easily accepts professional “+4 dBu” operat-
ing levels.
If the OL (Overload) LED is blink-
ing frequently or continuously, turn
down the amplifier’s Gain control or
the source signal (i.e., the mixer’s
master faders).
OL
-3
-6
-9
-20
SIG
OL
-3
-6
-9
-20
SIG
2
INTERNAL
STATUS
INTERNAL
STATUS
PROTECT
SHORT
OVER TEMP
PROTECT
SHORT
OVER TEMP
OO
MAXMAX
OO
1
M.4000
POWER
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-b.png)
11
Owner’s Manual
Owner’s Manual
3. PROTECT Indicator
If the PROTECT LEDs are on, the amplifier’s output
section has shut down. That, of course, means you won’t
hear anything until you rectify the situation. Three
things can cause the PROTECT circuit to engage:
1. Powering up the amplifier. A built-in delay circuit
saves your speakers (and ears) from the thumps or
pops that can sometimes occur when powering up a
system. During this three-second delay, the PRO-
TECT LEDs light up.
2. A short circuit (or near short) in either of the
outputs. Both the PROTECT and the SHORT LEDs
light up.
3. The temperature in the amplifier has risen to an
unsafe level. The PROTECT and the OVER TEMP
LEDs light up.
The M-Series amplifier draws its ventilation air in
from the rear and out through the front. The amp needs
plenty of fresh air to stay cool. DO NOT BLOCK THE
VENTILATION PORTS. See “Thermal Considerations” on
page 16 for more details.
Note: In the unlikely event that the power transformer
overheats (in general, this cannot happen during nor-
mal use — but could occur when bench testing at high
power levels for an extended period of time), the PRO-
TECT LED will light, but not the OVER TEMP LED. It
takes from one to two hours for the transformer to cool
to a safe temperature, when normal operation resumes.
4. SHORT Indicator
If this LED comes on, the amplifier has detected a
short circuit (or near short) in either of the outputs,
meaning that the hot (+) and cold (–) speaker wires
are touching, or a speaker itself is shorted out. Such
a condition causes the amplifer to engage its Protect
mode, muting all signals at the amp’s outputs.
This short-circuit LED is a Mackie exclusive and can
save precious minutes of your troubleshooting time.
Without it, you’d still have speaker and amp protection
(via the PROTECT circuit), but you wouldn’t be able
to determine the source of the problem. But with the
SHORT LED, the M-Series amplifier comes right out and
tells you!
WARNING: The SHORT LEDs
indicate an unsafe condition for the
power amplifier. When the short-
circuit protection is activated, the
SHORT LED lights, then the PRO-
TECT LED lights and the SHORT LED turns off. After
about four seconds, the protection circuit turns off and
the amplifier resumes normal operation. If it senses the
shorted condition again, the cycle repeats until you fix
the problem.
Typical causes for a “short” indication would be either
a shorted speaker cable or too many speaker cabinets
connected to the amplifier (i.e., the load impedance
is too low). If a “short” is indicated, please check your
cables. If the cabling is OK, then reduce the number of
cabinets driven by the amplifier.
Note: When using the amplifier in BRIDGE mode, one
or both SHORT LEDs may light under shorted or low im-
pedance conditions. Regardless of whether one or both
LEDs light, it’s an indication of a problem that requires
further investigation.
5. OVER TEMP Indicator
OVER TEMP (short for over-temperature) is another
feature designed to keep your mind at ease. Under
extreme conditions the amplifier may overheat. You may
ask, “What kind of extreme conditions?”
Overheating problems are usually caused by one of
the following situations: improper ventilation, high
ambient temperatures, overdriving the amplifier into
clipping, driving the amplifier hard into low-impedance
loads, frayed or partially shorted speaker cables, or
defective or internally shorted speakers.
The heaviest load the M-Series amplifier can toler-
ate is 2 ohms per channel (4 ohms in bridged mode). If
you’ve got a set of speakers wired in parallel, be sure the
load isn’t adding up to less than 2 ohms. Anything below
2 ohms can cause the SHORT LED to light and trigger
the PROTECT mode, or cause the amplifier to overheat,
which also triggers the PROTECT mode.
Note: Since each channel has its own
temperature sensor and protection
circuit, it is possible for only one
channel to go into PROTECT mode
while the other channel continues to
operate.
As the internal temperature of the amplifier rises, the
fans turn on at 50°C (122°F), and they kick into high
speed at 65°C (149°F). More air moves through the
constant temperature gradient cooling tunnel to remove
additional heat from the output transistors. However, if
the internal temperature of the amplifier should exceed
85°C (185°F), the OVER TEMP LED turns on, and both
PROTECT LEDs shine. The output of the amplifier is
muted — at this point the amplifier is in Protect mode
and remains there until the internal temperature cools
off to a safe level (60°C or 140°F). When this occurs,
the OVER TEMP and PROTECT LEDs turn off, and nor-
mal operation resumes.
![](asset-c.png)
12
M-Series
M-Series
Be Aware: If the OVER TEMP LED comes on fre-
quently, something is overworking the amplifier or it’s
not properly ventilated. Look at each of the “extreme
conditions” described above and try to determine what
is causing the amplifier to overheat. Refer to “Thermal
Considerations” on page 16 or to the “Troubleshooting”
section in Appendix A for more help.
You may ask, “Why don’t the fans just
go fast all the time?” Well, if it did,
you might actually hear it whirring
during your quiet moments (there
are quiet moments in your life,
aren’t there?). While this whirring
would be of no concern in most live-sound situations, it
could become annoying in a control room environment.
So, when the M-Series amplifier is not working hard, the
fans are off (or they go slow); when the music gets loud
and puts the amp to work, the fans go fast.
6. POWER Switch
To make the amp operate, push the top half of the
POWER switch. It clicks into place and the light in the
switch illuminates. To turn the amp off, push the lower
half. It’ll click again and the light will extinguish.
When you power up the M-Series amplifier, a built-in
delay circuit prevents any pops or thumps from being
transmitted to the speakers due to turn-on instability
in the system. Be sure the signal driving the amplifier is
turned down when you first power up the system. There
are few things as rude as 3 seconds of silence followed
by 250 watts of full-blast stereo sound! (Well, maybe 250
watts of accordian music...)
If you shut down your system, turn off your amplifiers
first. When powering up, turn on your amplifiers last.
This way, equipment feeding the amp won’t “pop” or
“thud” when it’s powered up or down.
Rear Panel
The rear panel of the M-Series amplifiers is comprised
of the fans, the input and output connectors, and a num-
ber of cool extra features.
7. SPEAKER OUTPUTS
There are two methods for connecting your speakers
to the M-Series amplifier, binding posts and Speakon®
connectors.
To use the binding post outputs, you can terminate
your speaker cables with single or double banana plugs,
spade lugs, or leave them unterminated with bare wire.
Unscrew the amp’s binding posts enough to reveal the
holes on their sides, then insert your stripped wires
(stripped about 3/8" back) into the holes and retighten
the posts (finger tight is fine — please don’t reef on
them with a wrench!). Be careful that no runaway
strands touch the chassis or other terminals.
The red posts are labeled “+,” which means positive.
The black posts are labeled “–” for negative. You prob-
ably know the importance of getting these terms correct
— if one side is hooked up “in phase” and the other side
is “out of phase,” you’ll be “out of work.” (By the way,
although everyone says “phase” in this situation, the cor-
rect word is “polarity”... but it’s not as much fun to say.)
Using high-quality stranded speaker cable (16 gauge
or thicker), connect the positive outputs of the ampli-
fier to the positive inputs of your speakers, and the
negative outputs to the negative inputs. The exception:
If you’re using the amplifier in BRIDGE mode, this does
not apply, (see Bridge Mode on page 19).
In addition to the binding posts, the M-Series ampli-
fier also has Speakon SPEAKER OUTPUTS. These have
the advantage of locking into place, and many profes-
sional loudspeakers are equipped with Speakon connec-
tors. There are three Speakon connectors, for channel 1,
channel 2, and for a bridged connection.
OL
-3
-6
-9
-20
SIG
OL
-3
-6
-9
-20
SIG
2
INTERNAL
STATUS
INTERNAL
STATUS
PROTECT
SHORT
OVER TEMP
PROTECT
SHORT
OVER TEMP
OO
MAXMAX
OO
1
M.4000
POWER
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-d.png)
13
Owner’s Manual
Owner’s Manual
See “Output Wiring” on page 18 for more info on mak-
ing the speaker output connections.
8. AMP MODE
This three-way switch, along with the X-OVER
switches, determines what kind of amplifier you want
the M-Series amplifier to be (or not to be — what was
the question?).
The AMP MODE switch determines the input signal
routing within the amplifier. Shipped from the factory,
the switch is set to STEREO. This is correct for about
90% of the applications using an amp like this. But you
may be in the 10% bracket, requiring special input rout-
ing within the amp.
The AMP MODE should be configured before opera-
tion — if you must change it during performance, turn
down the Gain controls as a precaution to protect the
speakers from any inadvertent pops or thumps.
STEREO mode (separate left and right inputs,
separate left and right outputs) is the typical setup for
amplifying stereo signals.
MONO mode (sometimes called Dual-Mono – one
mono input, two mono outputs) is for sending a mono
signal to two different speaker sets, with separately-
adjustable Gain controls.
BRIDGE mode (sometimes called Bridged-Mono – one
mono input, one mono output) uses both sides of the
amp to double the power to one speaker set. With two
M-Series power amplifiers, each set to BRIDGE mode,
you can deliver as much as 4000 watts per amplifier for
the M•4000 (2000 watts for the M•2000 and 3000 watts
for the M•3000).
If you set the AMP MODE switch to MONO or
BRIDGE, normally you would use just the Channel 1
input. You can connect a stereo input to Channels 1 and
2, but the M-Series amplifier sums the two inputs and
delivers a mono signal to the amplifier stage.
9. INPUTS
The M-Series amplifiers give you a choice — it has
combination XLR and 1/4" inputs, as well as screw
terminal balanced input connectors. Sonically (and
electrically) they’re identical. Since these inputs are
all in parallel (the Thru jacks are in parallel with the
inputs as well), you shouldn’t connect more than one
source to the INPUT connectors. Each can be used with
either balanced or unbalanced signals. See “Input Wir-
ing” on page 17 for more information about making the
input connections.
The M-Series amplifier expects to see a nominal sig-
nal level anywhere between the –10dBV “semipro” and
+4 dBu “pro” standards, meaning almost any line-level
mixer or other device can be plugged into the amp’s
INPUTs. Use the Gain controls to adjust the gain of the
amplifier to match the signal level you’re using.
10. Thru Connectors
Someday you’ll do a show and realize that one M-Series
amplifier is just not going to do the job — you’ll need a
six-foot-high rack full of ’em. That’s what the Thru jack
is for. Simply plug the signal source outputs into the
first amp’s INPUTs, patch from that amp’s Thru
jacks
to the next amp’s INPUTs, and so on, daisy-chaining as
many amps as you can afford (assuming your console has
low-impedance outputs).
A general rule of thumb is to maintain a load imped-
ance 10 times or more than the source impedance to
prevent excessive loading. If your console has an output
impedance of 100 ohms, then you can daisy-chain up to
twenty-four M-Series amplifiers, which presents a load
of 1000 ohms to the console (input impedance of 24
kohms divided by 24 amplifiers = 1000 ohms).
The Thru jacks can also be used to relay the signal on
to other devices such as a DAT or cassette recorder, en-
abling you to record exactly what the audience is hear-
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-e.png)
14
M-Series
M-Series
ing. The Thru jacks are wired straight from the XLR and
TRS INPUTs — there is no electronic circuitry between
— so the signal going into the amp is exactly the same
as the signal coming out of the Thru jacks.
You can use the Thru jack as an input, if necessary,
since it’s wired in parallel with the other input con-
nectors. You can also use the 1/4" TRS INPUT jacks as
Thru jacks. Simply connect the 1/4" TRS INPUT jacks
on the first amplifier to the TRS 1/4" INPUT jacks on the
second amplifier using 3-conductor shielded cables with
TRS plugs on both ends.
Warning: If you use a regular guitar cord with 2-
conductor TS plugs, you’ll unbalance the signal at the
screw terminal input by grounding the low side (–) of
the signal (pin 3).
11. 150 Hz X-OVER
This switch allows you to turn your M-Series ampli-
fier into a combination two-way crossover and power
amplifier. You can use one channel to power a woofer or
subwoofer, and the other channel to power the mid and
high frequencies.
For normal operation, leave the switch in the FULL
position. This allows full-range operation for that chan-
nel (no crossover filter).
With the switch in the LPF (low-pass filter) position,
all the frequencies below 150 Hz are allowed through
the channel, and all the frequencies above 150 Hz are
rolled off with a 2nd-order Butterworth filter.
With the switch in the HPF (high-pass filter) position,
all the frequencies above 150 Hz are allowed through
the channel, and all the frequencies below 150 Hz are
rolled off with a 2nd-order Butterworth filter.
To use the X-OVER switches in a two-way or bi-amplified
system:
1. Connect the same input signal to Channel 1 and
Channel 2 inputs. If you are using the screw termi-
nal inputs, you could jumper the signal over from
Channel 1 to Channel 2 as shown below.
GND
CHANNEL 1
GND
CHANNEL 2
GND
CHANNEL 1
GND
CHANNEL 2
JUMPERS
SHIELD
SHIELD
HOT (+)
COLD (--)
If you are using the combination input, you could
use the Thru connector from Channel 1 to connect
to the input of Channel 2.
2. Set the AMP MODE switch to STEREO.
Note: You cannot use the AMP
MODE switch set to MONO to ac-
complish this because the X-OVER
switches are located before the AMP
MODE switch in the signal path.
3. Set the X-OVER switch on Channel 1 to LPF and the
X-OVER switch on Channel 2 to HPF.
4. Connect the Speaker Output for Channel 1 to the
woofer or subwoofer speaker cabinet.
5. Connect the Speaker Output for Channel 2 to the
full-range or mid/high speaker cabinet.
You could also use the X-OVER switch as a high-pass
filter for both channels. For example, in a monitor sys-
tem, many monitor speakers don’t reproduce frequen-
cies below 100 Hz or 150 Hz. By rolling off the lower
frequencies, you can preserve the amplifier’s power for
the frequencies that count, and the system will sound
louder and cleaner.
12. LIMIT
The LIMITER is not designed to alter your sound — it’s
just there to protect your speakers from clipping. Its ef-
fect is virtually transparent, meaning you probably won’t
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
++
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-f.png)
15
Owner’s Manual
Owner’s Manual
14. Power Receptacle
This is a standard 3-prong IEC power connector.
Connect the detachable linecord (included in the box
with your M-Series amplifier) to the power receptacle,
and plug the other end of the linecord into an AC outlet
properly configured with the correct voltage for your
particular model.
The power cord that comes packed
with your amplifier may look like the
same one that plugs into your mixer
or computer, but it’s not! An IEC
power cord that you find on a typical
product will likely have tiny 18 gauge wire inside. The
power cord that comes with our amplifier has 14 gauge
wire inside, 250% larger than that of an 18 gauge cord. If
you use one of these lighter gauge cords on your ampli-
fier it may, quite literally, melt! So don’t lose that power
cord, but if you do, contact Mackie for a replacement.
For current-delivery purposes, the amplifier’s voltage
source (wall outlet, extension cords, or power strips)
must be capable of continuously delivering the following
AC current (for 120V version):
M•2000 9 amps
M•3000 12 amps
M•4000 15 amps
And for safety reasons, that source must be a “3-prong”
outlet with hot, neutral, and ground terminals. We’re
dealing with some big-time electricity here — don’t
mess with it. See “AC Power Considerations” on page 16
for more details.
15. Fans
There are two fans, one for each amplifier channel.
They pull air in from the rear, move it through the con-
stant thermal gradient heatsinks, and exhaust the warm
air through the front.
When the amplifier is first turned on, the fans are off.
They remain off until the inside of the amplifier warms
to 50º C (122º F). The fans start up at a slow speed until
the inside of the amplifier warms to 65º C (149º F),
when they kick into high speed.
In a live sound application, the sound of the fans is
usually not a problem. But in a control room or quiet
listening situation, it may be of a concern. When the am-
plifier is idling or operating at a low power, the fans are
off so you don’t hear the constant whirring of the fans.
At moderate power levels, the fans turn on at a slow
speed, so they probably still won’t be audible above the
program that you are listening to. At high power levels,
the fans may kick into high speed, but the high volume
level will certainly cover the sound of the fans.
It is important to leave space in front of and behind
the amplifier so the air can flow freely. See “Thermal
Considerations” on page 16 for more information.
even notice any audible difference. We recommend that
you leave it engaged, hence the TYPICAL label above it.
If you’re working at quiet levels all the time, or you’ve
already placed a compressor/limiter in the signal path,
or if you just hate compression, you can leave the LIM-
ITER out of the circuit (OFF).
The LIMITER works independently on each channel.
It
senses when the amplifier channel is about to be over-
driven and attenuates the overall level just enough to keep
the signal from clipping. Clipping occurs when the output
voltage no longer linearly follows the input voltage and
simply stops. This causes a sine wave to “square off,” and
the average power going into the speaker is roughly double
that of a sine wave. Square waves sound awful, and could
possibly damage your speakers and/or your reputation.
The LIMITER is especially handy when you’re working
with loud output levels. Having the signal spikes (kick
drum, for instance) attenuated a bit can actually in-
crease the apparent loudness of the overall mix without
diminishing the “power” behind the spikes.
Also, if you are driving the amplifier quite hard in
an adverse environment (high heat) and under heavy
loading, turning on the LIMITER will help to prevent the
amplifier from going into “OVER TEMP” protection. This
is much more preferable to lightening the load on the
amplifier by reducing the number of speakers connected.
Be Forewarned: With the LIMITER engaged, you can
still overdrive the amplifier into clipping and cause
distortion. It just takes a stronger signal to do it. So
even with the LIMITER turned on, you should still pay
attention to the OL LEDs.
13. AC LINE BREAKER
This is a resettable circuit breaker that monitors the
amount of current being drawn by the amplifier. Under
normal operating conditions, this should never pop. An
unusual condition may cause the breaker to pop, such
as a mains voltage surge occurring at the same time as a
peak amplifier output.
Turn the POWER switch off, and push the BREAKER
button to reset the circuit breaker. Turn the POWER
switch back on and the amplifier should resume normal
operation. If the circuit breaker pops again, something
probably isn’t right.
• Make sure the total impedance of the speakers
connected to the outputs is 2 ohms or greater (per
channel) in stereo mode, or 4 ohms or greater in
bridged mode.
• If the breaker pops right away, even with the Gain
controls turned down and the speakers discon-
nected, there may be something wrong inside the
amplifier. Refer to “Appendix A: Service Info.”
![](asset-10.png)
16
M-Series
M-Series
General Precautions and Considerations
AC Power Considerations
Be sure the amplifier is plugged into an outlet that
is able to supply the correct voltage specified for your
model.
If the line voltage should drop below about 97% of
the rated voltage, the amplifier will no longer be able to
supply rated power. (It will continue to operate down to
65% of the rated line voltage, but it just won’t be able to
reach full rated power.)
Be sure the AC outlet can supply enough current to
allow full power operation of all the amplifiers plugged
into it. The outlet should be a socket that matches the
power cord.
WARNING: Bypassing the plug’s
ground pin can be dangerous. Don’t
do it!
The AC current demand of an amplifier varies depend-
ing on several factors, including the crest factor and
the duty cycle of the program material. Under typical
conditions reproducing rock music where musical peaks
are just below clipping, the M-Series amplifiers require
the following average currents:
Average
Current
M•2000 Amplifier Loading Required
120V 240V
2 ohms per side or 4 ohms bridged 8.6A 4.3A
4 ohms per side or 8 ohms bridged 5.6A 2.8A
8 ohms per side or 16 ohms bridged 3.7A 1.9A
M•3000 Amplifier Loading
120V 240V
2 ohms per side or 4 ohms bridged 11.1A 5.6A
4 ohms per side or 8 ohms bridged 7.4A 3.7A
8 ohms per side or 16 ohms bridged 4.8A 2.4A
M•4000 Amplifier Loading
120V 240V
2 ohms per side or 4 ohms bridged 14.2A 7.1A
4 ohms per side or 8 ohms bridged 9.3A 4.7A
8 ohms per side or 16 ohms bridged 6.0A 3.0A
Rack Mounting
The M-Series amplifiers require two rack space units
(2 IU = 3.5"). The M•2000 requires 17.0" depth inside
the rack, including the rear supports. The M•3000 and
M•4000 require 19.5" depth inside the rack, includ-
ing the rear supports. When designing your rack, put
the heavier items at the bottom and the lighter items
toward the top.
Secure the front panel of the amplifier to the front of
the rack using four screws with soft washers to prevent
scratching the panel. In addition, because of the weight
of the amplifier, you must secure the rear support brack-
ets of the amplifier to the back of the rack. You could
use a support rail or shelf across the back of the rack,
or angle brackets attached between the rear support
brackets and the rear rails of the rack. This is recom-
mended for all components mounted in a rack that is
going to be moved frequently (or thrown in the back of a
pickup truck and transported down a bumpy gravel road
to that outdoor festival!).
Thermal Considerations
The M-Series amplifier is fan-cooled and brings air in
through the rear and out through the front. Make sure
that cool air is available at the rear of the amplifier, and
that there is room at the front for the warm air to exit
from the amplifier and dissipate. If rack-mounted, make
sure the amplifier is not pulling warm (or hot) air in
from the rack.
The M-Series amplifier’s unique Constant Thermal
Gradient heatsinks provide substantially better cool-
ing for the output transistors than conventional de-
signs that simply blow air through the chassis, getting
dust and other contaminants over all the internal
components. The heatsinks contain a cooling tunnel
that provides a shorter, more directed path for the air,
with the air moving faster toward the end of the tunnel
to balance the temperature along the entire length of
the heatsink. This results in increased reliability and
longevity for the amplifier because the output transis-
tors are kept cooler.
![](asset-11.png)
17
Owner’s Manual
Owner’s Manual
AC Power Distribution
In order to minimize ground loops, the safety grounds
for all the outlets should be connected to a common
(“star”) grounding point, and the distance between the
outlets and the common grounding point should be as
short as possible.
If lighting is used in a show, it is preferable to power
the lights from a different AC circuit than the one
powering the audio equipment. This will help minimize
noise from the lights coupling into the audio (particu-
larly if SCRs are used).
Input Wiring
Use a high-quality 3-conductor shielded cable to
connect the signal between the signal source (mixing
console, equalizer, etc.) and the balanced inputs to the
amplifier. If you’re making an unbalanced connection,
use a high-quality 2-conductor shielded cable. Your
Mackie Dealer can recommend a suitable cable for your
application.
Refer to “Inputs” [9] on page 13 for more information
about making the input connections.
When connecting a balanced line-level signal using
XLR plugs, they’re wired thusly, per AES (Audio Engi-
neering Society) standards:
Pin 2 = Hot (+)
Pin 3 = Cold (–)
Pin 1 = Shield (Ground)
2
2
31
1
SHIELD
COLD
HOT
SHIELD
COLD
HOT
3
SHIELD
COLD
HOT
3
2
1
Balanced XLR Connectors
Balanced TRS (tip-ring-sleeve) plugs can be con-
nected to the combination jacks as well. They are wired
as follows:
Tip = Hot (+)
Ring = Cold (–)
Sleeve = Shield (Ground)
SLEEVE
TIPSLEEVE
TIP
RING
RING
TIP
SLEEVERING
Balanced TRS Connectors
It is recommended that a stiff supply of AC power be
used because the amplifier places high current demands
on the AC line. The more power that is available on the
line, the louder the amplifier will play and the more
peak output power will be available for cleaner, punch-
ier bass.
Under typical conditions, reproducing rock music
where musical peaks are just below the clipping point,
you can safely connect one or more amplifiers to an AC
service. Use the table below as a guideline:
The M-Series amplifiers are equipped with an in-rush
limiting circuit to minimize startup current and pre-
vent tripping the breakers when two or more amplifiers
are turned on at the same time, on the same breaker.
Sequencing is not required.
If you use an extension cord to supply power to the
“amp rack,” it should have a third wire safety ground to
avoid presenting a safety hazard. We also recommend
using a cord that has conductors large enough to avoid
severely limiting the amplifier’s ability to supply high
currents on transients.
Power amplifiers can have momentary peak current
requirements many times above the nominal average
current draw. According to Ohm’s Law, the greater the
resistance of the linecord, the more input power is lost
between the AC outlet and the power amplifier (across
the linecord). And to further aggravate the matter,
this relationship is nonlinear. The amount of power
lost across the linecord increases exponentially as the
current demand increases. So if the current demand
doubles momentarily because of an exceptionally loud
bass note, the amount of AC input power lost across
the linecord increases four times. You can see that it
is very important to keep the resistance of the line-
cord to a minimum. That’s why we recommend using a
heavy gauge extension cord (like 14 gauge or bigger).
Remember, wire gets thicker as the gauge number gets
smaller (10 gauge is thicker than 14 gauge).
Maximum Number of Amplifiers
on a 120V/15A Service
M•2000 Amplifier Loading (or 240V/7.5A Service)
2 ohms per side or 4 ohms bridged 2
4 ohms per side or 8 ohms bridged 3
8 ohms per side or 16 ohms bridged 4
M•3000 Amplifier Loading
2 ohms per side or 4 ohms bridged 1
4 ohms per side or 8 ohms bridged 2
8 ohms per side or 16 ohms bridged 3
M•4000 Amplifier Loading
2 ohms per side or 4 ohms bridged 1
4 ohms per side or 8 ohms bridged 1
8 ohms per side or 16 ohms bridged 2
![](asset-12.png)
18
M-Series
M-Series
Unbalanced TS (tip-sleeve) signals can be accom-
modated via the combination jack. Make sure the cord
terminates with a TS plug (like a guitar plug), or if it’s a
TRS plug (like a headphone plug), make sure the ring is
tied to the shield, preferably at the source.
SLEEVE
TIP
TIP
SLEEVE
TIP
SLEEVE
Unbalanced TS Plug
The screw terminal connections are clearly marked,
indicating “+”, “–”, and GND. You can use bare wire to
wrap around the screws, or spade lugs connected to the
wires.
GND
CHANNEL 1
GND
CHANNEL 2
GND
CHANNEL 1
GND
CHANNEL 2
SHIELD
SHIELD
HOT (+)
COLD (--)
Balanced Screw Terminal Connection
If connecting an unbalanced line-level input to the
screw terminals, connect a jumper between the “–” and
GND screws.
GND
CHANNEL 1
GND
CHANNEL 2
GND
CHANNEL 1
GND
CHANNEL 2
SHIELD
SHIELD
HOT (+)
JUMPER
Unbalanced Screw Terminal Connection
Output Wiring
Use heavy gauge, stranded wire for connecting speak-
ers to the M-Series amplifier’s SPEAKER OUTPUT
terminals. As the distance between the amplifier and
the speakers increases, the thickness of the wire should
also increase. Speaker wire has resistance, and when
electricity passes through a resistor, power is lost. The
thicker the wire, the less resistance it offers, and the
more power actually gets to the speakers.
The thickness of wire is rated in gauges. Use the chart
below to determine the correct gauge of wire to use
according to the distance between the speakers and the
amplifier, and the impedance of the load the amplifier
is driving. This ensures that the power lost across the
speaker wire is less than 0.5 dB.
Stereo and Mono Modes
Binding Posts
When using the binding post outputs in stereo or
mono modes, you can terminate your speaker cables
with single or double banana plugs, spade lugs, or leave
them unterminated (bare wires): unscrew the amp’s
binding posts enough to reveal the holes on their sides,
then insert your stripped wires (stripped about 3/8"
back) into the holes and retighten the posts (finger
tight is fine). Be careful that no runaway strands touch
the chassis or other terminal.
Up to 25 ft. 2Ω 14 gauge
4Ω 16 gauge
8Ω 18 gauge
Up to 40 ft. 2Ω 12 gauge
4Ω 14 gauge
8Ω 18 gauge
Up to 60 ft. 2Ω 10 gauge
4Ω 12 gauge
8Ω 16 gauge
Up to 100 ft. 2Ω 8 gauge
4Ω 10 gauge
8Ω 14 gauge
Up to 150 ft. 2Ω 6 gauge
4Ω 8 gauge
8Ω 12 gauge
Up to 250 ft. 2Ω 4 gauge
4Ω 6 gauge
8Ω 10 gauge
Load Gauge of
Wire Length Impedance Wire
![](asset-13.png)
19
Owner’s Manual
Owner’s Manual
Bridge Mode
Binding Posts
When using the binding posts in bridge mode, connect
the positive side of the speaker cable to the CHANNEL
1 red (+) binding post, and connect the negative side
of the speaker cable to the CHANNEL 2 red (+) bind-
ing post. No, that’s not a typo. You only use the red
binding posts in Bridge mode. Do not use the black
posts.
TO SPEAKER
+ –
BRIDGE
+
+ +
SPEAKER OUTPUTS
Bridge Binding Post Connection
Speakon
When using bridge mode, wire the Bridge Speakon
connector the same as the stereo and mono connectors:
Bridge Speakon Connection
The red posts are labeled “+,” which means positive.
The black posts are labeled “–” for negative. Be sure
to connect the positive speaker output terminal to the
positive connection on the speaker cabinet, and the
negative speaker output terminal to the negative con-
nection on the speaker cabinet.
Speakons
When using the Speakon outputs in stereo or mono
modes, wire the Speakon connectors as shown below:
Stereo and Mono Speakon Connection
G
N
D
Bare Wire
Double Banana Plug
1/4"
Spade Lug
COLD
HOT
1+
1+
1–
1–
2–
2+
COLD
HOT
1+
1+
1–
1–
2–
2+
![](asset-14.png)
20
M-Series
M-Series
Dual-Channel Connection
The Channel 1 Speakon connector has the added
feature of providing both speaker outputs on a single
connector. This allows you to use a single cable to carry
both channels from the amplifier to the speakers. Refer
to the hookup diagram on page 7 for a typical applica-
tion using the dual-channel connection.
Many speakers with Speakon connectors provide an
Input connector and a “Thru” connector for connecting
a second speaker in parallel. You can use the Thru con-
nector on the speaker cabinet to connect the Channel 2
amplifier output to the Channel 2 speaker.
For the cable connecting the amplifier to the first
speaker, wire all four pins in the Speakon connector, as
shown below, at both ends of the cable. For the cable
connecting the “Thru” connector to the second speaker,
you need to use a “crossover” cable that connects pins
2+ and 2– on the “Thru” connector to pins 1+ and 1– on
the second speaker input end.
Stereo Dual-Channel Speakon Connection
M.4000
AC LINE
BREAKER
(PUSH TO RESET)
SERIAL / DATE CODE
BRIDGE
+
+ +
1 2
BRIDGE
PIN 1 = CH1
PIN 2 = CH2
PIN 1 = BRIDGE
PIN 2 = UNUSED
PIN 1 = CH2
PIN 2 = UNUSED
LETHAL
VOLTAGES
MAY APPEAR
AT OUTPUT
TERMINALS.
CLASS 3 WIRING
IS REQUIRED.
SPEAKER OUTPUTS
12
ON/
TYPICAL
LIMIT
OFF
STEREO
AMP
MODE
MONO
BRIDGE
CAUTION
GND
CHANNEL 1
GND
CHANNEL 2
ON/
TYPICAL
LIMIT
OFF
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA
MANUFACTURED IN CHINA • FABRIQUE EN CHINE
©2005 LOUD TECHNOLOGIES INC. • “MACKIE” AND
THE “RUNNING MAN” FIGURE ARE REGISTERED
TRADEMARKS OF LOUD TECHNOLOGIES INC.
1300W / CH
4Ω LOAD MIN
2600W BRIDGE
8Ω LOAD MIN
~120VAC 60Hz 1600W
INPUT INPUT
LPF
HPF
FULL
LPF
HPF
FULL
150Hz
X-OVER
150Hz
X-OVER
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION
HIGH EFFICIENCY POWER AMPLIFIER
FROM MIXING CONSOLE
LEFT AND RIGHT MAIN OUT
AMP MODE SWITCH
STEREO
Passive Speakers (Mackie S408)
Crossover Cable
(Pin 2+ to Pin 1+
Pin 2– to Pin 1–)
COLD
COLD
AMPLIFIER
END
SPEAKER
END
HOT
CHANNEL 1
CHANNEL 2
1+
1–
2–
2+
1+
1–
2–
2+
COLD
FROM "THRU"
OUTPUT
TO SECOND
SPEAKER INPUT
FROM "THRU"
OUTPUT
TO SECOND
SPEAKER INPUT
TO FIRST
SPEAKER INPUT
HOT
CHANNEL 2
1+
1–
2–
2+
1+
1–
2–
2+
![](asset-15.png)
21
Owner’s Manual
Owner’s Manual
Appendix A: Service Information
• Is the SHORT [4] LED lit? Turn the POWER off,
check the speaker connections and make sure that
there are no strands of wire shorting across the
speaker terminals.
• Is the OVER TEMP [5] LED lit? Make sure there is
cool air available at the rear of the amplifier. Make
sure there is room at the front of the amplifier for
warm air to exit. Allow the amplifier to cool off.
• Is the PROTECT [3] LED lit? The power trans-
former may have overheated and shut down the
amplifier. Turn the amplifier off and wait until
the transformer cools down (it could take several
hours).
• Are there fuses in the speaker or in-line fuses in the
speaker wire? Check ’em to see if they’re blown.
• Make sure the speakers are working properly.
One side is way louder than the other!
• Do the amplifier’s meters [2] read the same on both
sides? If not, your source signal may be delivering
an out-of-balance stereo signal.
• Are both Gain [1] knobs set to the same position?
• Are the speaker(s) impedances matched?
• Try swapping sides: Turn off the amp, swap the
speaker cables at the amp, turn the amp back on.
If the same side is still louder, the problem is with
your speakers or speaker cabling. If the other side
is louder now, the problem is with the mixer, the
amp, or the line-level cabling.
The stereo music sounds kind of sideways,
and the bass frequencies diminish when
standing center, but get louder as you ap-
proach one side!
• Check the polarity of the speaker cable connec-
tions. You may have your positive and negative con-
nections reversed at one end of one speaker cable.
As soon as the music gets loud, the amp
shuts down!
• Check the amplifier’s meters [2]. Be sure that OL is
not lighting up frequently or continuously.
• Can the amp breathe? The M-Series amplifier draws
its ventilation air in from the rear and out through
the front. It needs plenty of fresh air to stay cool.
Do not block the ventilation ports.
• Is the SHORT [4] LED lit? If so, you’ve got a dead
short somewhere in your speaker setup, or the total
impedance of the load is too low. Turn the amp off
and rectify that right away.
Warranty Service
Details concerning Warranty Service are spelled out in
the Warranty section on page 27.
If you think your M-Series amplifier has a problem,
please do everything you can to confirm it before calling
for service. Doing so might save you from the depriva-
tion of your amplifier and the associated suffering.
These may sound obvious to you, but here are some
things you can check. Read on.
Troubleshooting
No Power
• Our favorite question: Is it plugged in? Make sure
the AC outlet is live (check with a tester or lamp).
• Our next favorite question: Is the POWER [6]
switch on? If not, try turning it on.
• Is the light in the power switch illuminated? If not,
make sure the AC outlet is live. If so, refer to “No
Sound” below.
• The AC line breaker on the rear panel has popped.
To reset the breaker, turn the power switch off,
push in the button on the breaker, and turn the
power switch back on.
If the breaker pops again, disconnect the speakers
from the amplifier and repeat the above procedure.
If the breaker pops again, there may be a problem
with the amplifier. Refer to “Repair” on the next
page to find out how to proceed.
No sound!
• Are the Gain [1] controls turned all the way down?
Slowly turn them up and see if you hear anything.
• Is the signal source turned up? Make sure the
signal level from the mixing console (or whatever
device immediately precedes the amplifier) is high
enough to produce sound in the amplifier. The SIG
LEDs [2] should be blinking to indicate that signal
is present.
• If the speakers are wired for BRIDGE mode, make
sure the AMP MODE [8] switch is set to BRIDGE.
• Is the X-OVER [11] switch set to LPF? If so, you are
only getting the lowest frequencies (below 150 Hz)
through the speakers. Set the X-OVER switch to the
FULL position to verify sound is present.
![](asset-16.png)
22
M-Series
M-Series
It hurts when I touch my arm, or my leg, or
even my head!
• You have a broken finger.
Bad sound!
• Is it loud and distorted? Turn down the signal com-
ing from the mixer or signal source.
• Is the input connector plugged completely into the
jack? Check the speaker connections and verify
that all connections are tight and that there are no
stray strands of wire shorting across the speaker
terminals.
• If possible, listen to the signal source with head-
phones plugged into the console. If it sounds bad
there, the problem’s not in the amplifier.
Noise/Hum
• Check the signal cable between the mixer and the
amplifier. Make sure all connections are good and
sound.
• Make sure the signal cable is not routed near AC
cables, power transformers, or other EMI-inducing
device.
• Is there a light dimmer or other SCR-based device
on the same AC circuit as the amplifier? Use an AC
line filter or plug the amplifier into a different AC
circuit.
• If possible, listen to the signal source with head-
phones plugged into the console. If it sounds noisy
there, the problem’s not in the amplifier.
For additional up-to-date information please visit our
website at www.mackie.com.
Repair
Service for Mackie products is available at a factory-
authorized service center. Service for Mackie products
living outside the United States can be obtained through
local dealers or distributors.
If your M-Series amplifier needs service, follow these
instructions:
1. Review the preceding troubleshooting suggestions.
Please.
2. Call Tech Support at 1-800-898-3211, 7 am to 5 pm
PST, to explain the problem and obtain a Service
Request Number. Have your serial number ready.
You must have a Service Request Number before
you can obtain warranty service.
3. Keep this owner’s manual and the detachable line-
cord. We don’t need them to repair the amplifier.
4. Pack the amplifier in its original package, includ-
ing endcaps and box. This is VERY IMPORTANT.
Mackie is not responsible for any damage that
occurs due to non-factory packaging.
5. Include a legible note stating your name, shipping
address (no P.O. boxes), daytime phone number,
Service Request Number, and a detailed description
of the problem, including how to duplicate it.
6. Write the Service Request Number in BIG PRINT
on top of the box. Units sent without the Service
Request Number will be refused.
7.
Tech Support will tell you where to ship the amplifier
for repair. We suggest insurance for all forms of cartage.
8.
You will need to contact the authorized service cen-
ter for their latest turn-around times. The amplifier
must be packaged in its original packing box, and
must have the Service Request Number on the box.
Once it’s repaired, the authorized service center will
ship it back, pre-paid (if it was a warranty repair).
Note: Under the terms of the warranty, you must
ship or drop-off the unit to an authorized service
center. The return ground shipment is covered for
those units deemed by us to be under warranty.
Note: You must have a sales receipt from an Autho-
rized Mackie Dealer to qualify for a warranty repair.
Need Help?
You can reach a technical support representative
Monday through Friday
from 7 AM to 5 PM PST at:
1-800-898-3211
After hours, visit www.mackie.com and click Support,
or email us at: techmail@mackie.com
![](asset-17.png)
23
Owner’s Manual
Owner’s Manual
Appendix B: Technical Info
Maximum Input Level:
9.75 volts (+22 dBu)
Rise Time (8 ohms):
< 6 µs
Slew Rate:
M•2000
Voltage Slew Rate 50V/µs
Current Slew Rate 25A/µs at 2Ω
H-Switch Slew Rate 10-50V/µs (program dependent)
M•3000
Voltage Slew Rate 55V/µs
Current Slew Rate 27.5A/µs at 2Ω
H-Switch Slew Rate 16-70V/µs (program dependent)
M•4000
Voltage Slew Rate 60V/µs
Current Slew Rate 30A/µs at 2Ω
H-Switch Slew Rate 16-70V/µs (program dependent)
CMRR:
> 34 dB, 20Hz to 20kHz
Load Angle:
8(±jx) time independent at 8Ω
4(±jx) time dependent, T > 6 min. at 4Ω
2(1±jx) time dependent, T > 2 min. at 2Ω
Transient Recovery:
< 1µs for 10 dB overdrive @ 1kHz
Maximum Output Offset Voltage:
±50 mV
M-Series Specifications
M•2000 M•3000 M•4000
Continuous Average Output Power in watts, both channels driven
20 Hz-20 kHz into 8 ohms per channel
325
475
650
20 Hz-20 kHz into 4 ohms per channel 525 800 1050
40 Hz-20 kHz into 2 ohms per channel 800 1200 1600
Bridge Mono: 20 Hz-20 kHz into 8 ohms 1050 1600 2100
Bridge Mono: 40 Hz-20 kHz into 4 ohms 1600 2400 3200
Maximum Output Power in watts, both channels driven
1 kHz @ 1% THD into 8 ohms per channel
400
600
800
1 kHz @ 1% THD into 4 ohms per channel 650 1000 1300
1 kHz @ 1% THD into 2 ohms per channel 1000 1500 2000
Bridge Mono: 1 kHz @ 1% THD into 8 ohms 1300 2000 2600
Bridge Mono: 1 kHz @ 1% THD into 4 ohms 2000 3000 4000
Note: Power ratings are specified at 120VAC (U.S. and Canada) and 240VAC (Export) line voltages.
The M-Series power amplifiers draw large amounts of current from the AC line with continuous sine wave testing. Accurate mea-
surement of power requires a steady and stable AC supply. This means the line impedance must be very low to insure that the peak
AC line voltage does not sag to less than 97% of its value.
If driving highly reactive loads, we recommend that the limiter circuit be engaged.
Power Bandwidth (rated power into 4 ohms):
20 Hz to 20 kHz
(Output power typically –3 dB at 50 kHz. Amplifier protection cir-
cuits typically mute the output signal above 40 kHz at full power.)
Frequency Response (1 watt into 8 ohms):
< 10 Hz to 55 kHz (+0, –3 dB)
Distortion:
THD, SMPTE IMD < 0.05% @ 8Ω
< 0.10% @ 4Ω
< 0.20% @ 2Ω
Signal-to-Noise Ratio:
> 107 dB below rated power into 4 ohms
Channel Separation:
> 80 dB @ 1 kHz
Damping Factor:
> 500 (8 ohms @ 400 Hz)
Input Impedance:
24 kΩ balanced
12 kΩ balanced
Input Sensitivity:
1.23 volts (+4 dBu) for rated power into 4 ohms
Gain:
M•2000 31.4 dB (37.3 V/V)
M•3000 33.3 dB (46.0 V/V)
M•4000 34.4 dB (52.7 V/V)
![](asset-18.png)
24
M-Series
M-Series
High Frequency Overload and Latching:
No latch up at any frequency or level.
High Frequency Stability:
Unconditionally stable driving any resistive or reactive load.
Turn On Delay:
3 seconds
High-Pass Filter:
150 Hz, 2nd-Order Butterworth
Low-Pass Filter:
150 Hz, 2nd-Order Butterworth
Limiter Section:
Complementary Positive and Negative Peak Detecting
Indicators:
Power ON LED (in power switch)
6 meter LEDs per channel
SIG (Signal Present), –20, –9, –6, –3, OL (Overload)
CH 1 & 2
PROTECT LEDs, SHORT LEDs, OVER TEMP LEDs
AC Line Power:
U.S./Canada 120VAC, 60Hz
Europe 240VAC, 50Hz
Japan 100VAC, 50/60Hz
Korea 220VAC, 60Hz
(Factory configured)
AC Drop-out Voltage:
At approximately 65% of rated line voltage
Physical:
M•2000
Height 3.5 in/89 mm
Width 19.0 in/483 mm
Depth 15.7 in/398 mm
Overall Depth 17.0 in/432 mm
Weight 41 lb/18.6 kg
M•3000
Height 3.5 in/89 mm
Width 19.0 in/483 mm
Depth 18.1 in/460 mm
Overall Depth 19.5 in/494 mm
Weight 48 lb/21.8 kg
M•4000
Height 3.5 in/89 mm
Width 19.0 in/483 mm
Depth 18.1 in/460 mm
Overall Depth 19.5 in/494 mm
Weight 53 lb/24.0 kg
LOUD Technologies Inc. is always striving to improve our prod-
ucts by incorporating new and improved materials, components,
and manufacturing methods. Therefore, we reserve the right to
change these specifications at any time without notice.
“Mackie.” and the “Running Man” are registered trademarks of
LOUD Technologies Inc. All other brand names mentioned are
trademarks or registered trademarks of their respective hold-
ers, and are hereby acknowledged.
©2006 LOUD Technologies Inc. All Rights Reserved.
M-Series Dimensions
M•2000
WEIGHT
36 lbs.
(16.3 kg)
17.1 in/435 mm
3.5 in/89 mm
19.0 in/483 mm
17.6 in/446 mm
OL
-3
-6
-9
-20
SIG
OL
-3
-6
-9
-20
SIG
2
INTERNAL
STATUS
INTERNAL
STATUS
PROTECT
SHORT
OVER TEMP
PROTECT
SHORT
OVER TEMP
OO
MAXMAX
OO
1
M.2000
POWER
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-19.png)
25
Owner’s Manual
Owner’s Manual
R
M•3000
WEIGHT
47 lbs.
(21.3 kg)
19.5 in/495 mm
3.5 in/89 mm
19.0 in/483 mm
17.6 in/446 mm
OL
-3
-6
-9
-20
SIG
OL
-3
-6
-9
-20
SIG
2
INTERNAL
STATUS
INTERNAL
STATUS
PROTECT
SHORT
OVER TEMP
PROTECT
SHORT
OVER TEMP
OO
MAXMAX
OO
1
M.3000
POWER
HIGH EFFICIENCY POWER AMPLIFIER
M•4000
WEIGHT
53 lbs.
(24.0 kg)
19.5 in/495 mm
3.5 in/89 mm
19.0 in/483 mm
17.6 in/446 mm
OL
-3
-6
-9
-20
SIG
OL
-3
-6
-9
-20
SIG
2
INTERNAL
STATUS
INTERNAL
STATUS
PROTECT
SHORT
OVER TEMP
PROTECT
SHORT
OVER TEMP
OO
MAXMAX
OO
1
M.4000
POWER
HIGH EFFICIENCY POWER AMPLIFIER
![](asset-1a.png)
26
M-Series
M-Series
M-Series Block Diagram
CH 1
BALANCED
LINE INPUT
(TRS)
CH 1
BALANCED
LINE INPUT
(XLR-F)
LIMITER
ON
OFF
HIGH PASS
FILTER
+
–
VDC
++
– –
VDC
+++
– – –
VDC
(M•3000/M•4000
ONLY)
TOROIDAL POWER
TRANSFORMER
MILLENIUM SPACE STATION
LAMP
MACKIE
M•2000/M•3000/M•4000
BLOCK DIAGRAM
(#022106DF)
AMP
MODE
SWITCH
LOW PASS
FILTER
CH 1
GAIN
STEREO
MONO
BRIDGE
CH 2
GAIN
INVERTING
UNITY GAIN
AMPLIFIER
150Hz
X-OVER
HPF
LPF
FULL
NC
POWER
AMPLIFIER
VOLTAGE
AMPLIFIER
CLASS-H
SWITCHING
CONTROL
METER
DRIVE
OL
–3
–6
–9
–20
SIG
CH 1
SIG
+V
SIG
(TO CH 1
METER DRIVE)
TEMP
SENSOR
(ON HEATSINK)
CH 2
AMP OUT
PROGRAM
DETECT
AND
OR
HI FAN SPEED
DETECTOR
65ºC TRIP
LO FAN SPEED
DETECTOR
50ºC TRIP
FAN
SPEED
CONTROL
HI DCV
LO DCV
OFF
BREAKER
AC IN-RUSH
LIMITER
POWER
SWITCH
TRANSFORMER
OVERTEMP
(TO CH 1/CH 2
PROTECTION)
THERMAL
PROTECT
UNDER-VOLT
(TO CH1/CH2
PROTECTION)
SUPPLY
UNDERVOLTAGE
DETECTOR
(65% OF NOMINAL)
THRU
(XLR-M)
CH 1
SCREW
TERMINAL
LINE INPUT
+
–
GND
FAN
2
3
1
2
3
1
CH 2
BALANCED
LINE INPUT
(TRS)
CH 2
BALANCED
LINE INPUT
(XLR-F)
THRU
(XLR-M)
CH 2
SCREW
TERMINAL
LINE INPUT
+
–
GND
2
3
1
2
3
1
SIG
(TO CH 2
METER DRIVE)
(TO CH 2
PROTECTION)
LIMITER
ON
OFF
HIGH PASS
FILTER
LOW PASS
FILTER
150Hz
X-OVER
HPF
LPF
FULL
++V
+++V (M•3000/M•4000 ONLY)
–V
– –V
– – –V (M•3000/M•4000 ONLY)
VOLTAGE
AMPLIFIER
POWER
AMPLIFIER
CLASS-H
SWITCHING
CONTROL
METER
DRIVE
OL
–3
–6
–9
–20
SIG
TEMP
SENSOR
(ON HEATSINK)
CH 1
AMP OUT
PROGRAM
DETECT
AND
OR
HI FAN SPEED
DETECTOR
65ºC TRIP
LO FAN SPEED
DETECTOR
50ºC TRIP
FAN
SPEED
CONTROL
HI DCV
LO DCV
OFF
FAN
(TO CH 1
PROTECTION)
CH 2
SIG
+V
PROTECTION
SHORT
OVER TEMP
SHORT
PROTECT
DC FAULT
X-FORMER OVERTEMP
HEATSINK OVERTEMP
OVER-VOLT
PROTECTION
SHORT
OVER TEMP
SHORT
PROTECT
DC FAULT
X-FORMER OVERTEMP
HEATSINK OVERTEMP
OVER-VOLT
++V
+++V (M•3000/M•4000 ONLY)
–V
– –V
– – –V (M•3000/M•4000 ONLY)
1+
1–
2–
2+
1+
1–
2–
2+
CHANNEL 1
SPEAKER
OUT
BRIDGED
SPEAKER
OUT
1+
1–
2–
2+ CHANNEL 2
SPEAKER
OUT
+
–
+
–
+
–
+
–
+
–
![](asset-1b.png)
27
Owner’s Manual
Owner’s Manual
A. LOUD Technologies Inc. warrants all materials, workmanship
and proper operation of this product for a period of five years
from the original date of purchase. If any defects are found
in the materials or workmanship or if the product fails to
function properly during the applicable warranty period, LOUD
Technologies, at its option, will repair or replace the product.
This warranty applies only to equipment sold and delivered
within the U.S. by LOUD Technologies Inc. or its authorized
dealers.
B. Failure to register online or return the product registration
card will not void the five-year warranty.
C. Service and repairs of Mackie products are to be performed
only at a factory-authorized facility (see D below). Unauthorized
service, repairs, or modification will void this warranty. To obtain
repairs under warranty, you must have a copy of your sales receipt
from the authorized Mackie dealer where you purchased the
product. It is necessary to establish purchase date and determine
whether your Mackie product is within the warranty period.
D. To obtain factory-authorized service:
1. Call Mackie Technical Support at 800/898-3211, 7 AM
to 5 PM Monday through Friday (Pacific Time) to get a
Service Request Number. Products returned without a Service
Request Number will be refused.
2. Pack the product in its original shipping carton. Also
include a note explaining exactly how to duplicate the
problem, a copy of the sales receipt with price and date
showing, and your return street address (no P.O. boxes or
route numbers, please!). If we cannot duplicate the problem
or establish the starting date of your Limited Warranty, we
may, at our option, charge for service time.
3. Ship the product in its original shipping carton, freight
prepaid to the authorized service center. The address of
your closest authorized service center will be given to you by
Technical Support.
IMPORTANT: Make sure that the Service Request Number
is plainly written on the shipping carton.
E. LOUD Technologies reserves the right to inspect any products
that may be the subject of any warranty claims before repair
or replacement is carried out. LOUD Technologies may, at our
option, require proof of the original date of purchase in the form
of a dated copy of the original dealer’s invoice or sales receipt.
Final determination of warranty coverage lies solely with LOUD
Technologies.
F. Any products returned to one of the LOUD Technologies
factory-authorized service centers and deemed eligible for repair
or replacement under the terms of this warranty will be repaired
or replaced within thirty days of receipt. LOUD Technologies
and its authorized service centers may use refurbished parts for
repair or replacement of any product. Products returned to LOUD
Technologies that do not meet the terms of this Warranty will be
not be repaired unless payment is received for labor, materials,
return freight, and insurance. Products repaired under warranty
will be returned freight prepaid by LOUD Technologies to any
location within the boundaries of the USA.
G. LOUD Technologies warrants all repairs performed for 90
days or for the remainder of the warranty period. This warranty
does not extend to damage resulting from improper installation,
misuse, neglect or abuse, or to exterior appearance. This
warranty is recognized only if the inspection seals and serial
number on the unit have not been defaced or removed.
H. LOUD Technologies assumes no responsibility for the quality
or timeliness of repairs performed by an authorized service
center.
I. This warranty is extended to the original purchaser and to
anyone who may subsequently purchase this product within the
applicable warranty period. A copy of the original sales receipt is
required to obtain warranty repairs.
J. This is your sole warranty. LOUD Technologies does not
authorize any third party, including any dealer or sales
representative, to assume any liability on behalf of LOUD
Technologies or to make any warranty for LOUD Technologies Inc.
K. THE WARRANTY GIVEN ON THIS PAGE IS THE SOLE
WARRANTY GIVEN BY LOUD TECHNOLOGIES INC. AND IS IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS AND IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE WARRANTY
GIVEN ON THIS PAGE SHALL BE STRICTLY LIMITED IN
DURATION TO FIVE YEARS FROM THE DATE OF ORIGINAL
PURCHASE FROM AN AUTHORIZED MACKIE DEALER. UPON
EXPIRATION OF THE APPLICABLE WARRANTY PERIOD, LOUD
TECHNOLOGIES INC. SHALL HAVE NO FURTHER WARRANTY
OBLIGATION OF ANY KIND. LOUD TECHNOLOGIES INC.
SHALL NOT BE LIABLE FOR ANY INCIDENTAL, SPECIAL, OR
CONSEQUENTIAL DAMAGES THAT MAY RESULT FROM ANY
DEFECT IN THE MACKIE PRODUCT OR ANY WARRANTY
CLAIM. Some states do not allow exclusion or limitation of
incidental, special, or consequential damages or a limitation on
how long warranties last, so some of the above limitations and
exclusions may not apply to you. This warranty provides specific
legal rights and you may have other rights which vary from state
to state.
Please keep your sales receipt in a safe place.
M-Series Limited Warranty
![](asset-1c.png)
16220 Wood-Red Road NE • Woodinville, WA 98072 • USA
United States and Canada: 800.898.3211
Europe, Asia, Central and South America: 425.487.4333
Middle East and Africa: 31.20.654.4000
Fax: 425.487.4337 • www.mackie.com
E-mail: sales@mackie.com