Makita 6805Bv Users Manual
6805BV to the manual b0baef06-a1e9-41f5-b126-6bd386ab1307
2015-02-05
: Makita Makita-6805Bv-Users-Manual-405534 makita-6805bv-users-manual-405534 makita pdf
Open the PDF directly: View PDF 
.
Page Count: 12
Screwdriver
Self drilling screw
MODEL
6805BV
Variable speed
I
Reversing
Machine screw Wood screw
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC
IF
I
CAT
I
0
N
S
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country
to
country.
WARNING: For your personal safety, READ and UNDERSTAND before using
SAVE THESE INSTRUCTIONS
FOR
FUTURE REFERENCE.
IMPORTANT
SAFETY INSTRUCTIONS
(For
All
Tools)
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK
OF
FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp
or wet locations. Keep work area well
lit.
Don't expose power tools to rain.
Don't use tool
in
presence of flammable liquids
or
gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not
in
use, tools should be stored in dry, and high
or locked-up place
-
out of reach of children.
DON'T FORCE TOOL.
It
will do the job better and safer at the rate for which
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in
moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
DON'T ABUSE CORD. Never carry tool
by
cord or yank
it
to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it
frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing acces-
sories. Inspect tool cords periodically and if damaged, have repaired by autho-
rized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not in use, before servicing, and when chang-
ing accessories, such
as
blades, bits, cutters.
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch.
Be sure switch is OFF when plugging in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
so
marked.
17.
STAY ALERT. Watch what you are doing, use common sense. Don’t operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of
the
tool, a guard or other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Don‘t
use tool if switch does not turn
it
on and off.
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
21.
POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way.
If
the plug does not
fit
fully in the outlet,
reverse the plug. If
it
still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result
in
SERIOUS INJURY to the user
-
as well as damage to
the tool.
If
in doubt,
DO
NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
ADDITIONAL SAFETY RULES
1.
2.
Hold the tool firmly.
3.
4.
Always be sure
you
have a firm footing.
Be sure no one is below when using the tool
in
high locations.
Keep hands away from rotating parts.
When driving into walls, floors or wherever "live" electrical wires may be
encountered,
DO
NOT TOUCH ANY METAL PARTS
OF
THE TOOL!
Hold the tool only by the insulated grasping surfaces to prevent electric shock
if
you
drive into a "live" wire.
Do
not touch the bit or the workpiece immediately after operation: they may
be extremely hot and could burn your skin.
5.
SAVE THESE INSTRUCTIONS.
4
Removing
or
installing bit
CAUTION
:
Always be sure that the tool
is
switched off and unplugged before removing or installing
the bit.
To remove the bit, first pull the front cap
off and then pull the bit firmly. To install
the bit, insert
it
into the tool
as
far
as
it
will go and then replace the front cap.
Depth adjustment
When you wish to drive self drilling screws,
etc.,
adjust the depth
as
follows. Turn the
locator to adjust the depth.
Initially, adjust the locator to create
a
dis-
tance of approximately
1
mm
(3/64”)
from
the tip of the front cap (which works in
conjunction with the locator) to the base
of the screw head. One full turn of the
locator equals
1
mm
(3/64“)
change in
depth. After adjusting the locator, turn
the adjusting ring
so
that the
6”
mark
is
aligned with the pointer on the gear hous-
ing. Drive
a
trial screw into your material
or
a
piece of duplicate material. If the
depth
is
not
suitable
for the screw, con-
tinue adjusting until the proper depth
set-
ting
is
obtained.
I
Adjusting ring-
\\
1
mm
(3/64”)
1
mm
(3/64”)
1
mm
(3/64”)
5
Adjusting fastening torque
When you wish to drive machine screws,
wood screws, hex bolts etc. with the pre-
determined torque, adjust the fastening
torque
as
follows.
The fastening torque may be adjusted by
turning the adjusting ring. Before turning
the adjusting ring, turn the locator in the
direction of the arrow
as
far
as
it
will go
without forcing. The torque
is
increased
by turning the adjusting ring in the direc-
tion of the arrow and decreased by turn-
ing
it
in the opposite direction. Align the
I
number
1
on the adjusting ring with the pointer on the gear housing. Drive
a
trial screw
into your material or
a
piece of duplicate material. If the fastening torque
is
not suitable
for the screw, continue adjusting until the proper torque
is
obtained.
CAUTION
:
The adjusting ring should be turned only within the numbered range.
It
should not be
forced beyond this range.
Switch action
Tool speed
is
increased by increasing
pressure on the trigger. To start the tool,
simply pull the trigger.
Release
the trigger
to stop. For continuous operation, pull the
trigger and then push in the lock button.
To stop the tool from the locked position,
pull the trigger fully, then release
it.
I
Trigger
switch
Lock
button
I
CAUTION
:
Before plugging in the tool, always check to
see
that the trigger switch actuates properly
and returns to
the
"OFF"
position when released.
NOTE
:
Even with the switch on and motor running, the bit will not rotate until you fit the point
of
the bit in the screw head and apply forward pressure to engage the clutch.
6
Reversing switch action
This tool has
a
reversing switch to change
the direction
of
rotation. Move
the
revers-
ing switch lever to the
&?
position for
clockwise rotation or the position for
counterclockwise.
Reversing
switch
lever
1
CAUTION
:
Always check the direction of rotation before operation.
*Use the reversing switch only when the tool comes to
a
complete stop. Changing the
direction of rotation before the tool stops may ruin the tool.
Operation
Fit the screw
on
the point of the bit and
place the point
of
the screw on the surface
of the workpiece to be fastened. Apply
pressure to the tool and start
it.
Withdraw
the
tool
as
soon
as
the clutch cuts in.
Then release the trigger.
CAUTION
:
0
Use the proper bit for the head of the screw that you wish to use.
When fitting the screw onto the point of the bit, be careful not to push in on the screw.
If the screw
is
pushed in, the clutch will engage and the screw will rotate suddenly. This
could damage
a
workpiece or cause an injury.
Do
not continue unnecessary clutching operation.
7
NOTE
:
0
Make sure that the driver bit
is
inserted straight in the screw head, or the screw and/or
When driving wood Screws, predrill pilot
bit may be damaged.
holes to make driving
easier
and to pre-
vent splitting of the workpiece.
See
the
chart.
of
wood screw of
pilot
hole
1
1/64"
13/64"
7/32"
3/16"
1/8"
9/64"
5/32"
iia"
15/64"
I
1
1/64"
114"
11
164''
MAINTENANCE
CAUTION
:
Always be sure
that
the
tool
is
switched off and unplugged before attempting to perform
inspection or maintenance.
To
maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and
replacement, any other maintenance or adjustment should be performed by Makita
Authorized or Factory Service Centers, always using Makita replacement parts.
8
ACCESSORIES
Part
No.
CAUTION
:
These accessories or attachments are recommended for
use
with your Makita tool specified in this
manual. The use
of
any other accessories or attachments might present
a
risk
of
injury to persons.
The accessories or attachments should be used only in the proper and intended manner,
0
Magnetic socket bit Front cap
Size
Part
No.
I
Size
784803-7 114"
784805-3
I
7/16"
0
Phillips bit
Part
No.
I
Size
3221 24-5 114''
,
3221 20-3
Slotted bit
~~
.
I
-
784215-0A
I
#3
Part
No.
I
Size
784010-OA
1
#5F
784011-0A
I
#7F
Square drill bit
Part
No.
784606-0A
Steel carrying case
Part
No.
181 853-7
9
May-28-'93
US
SCREWDRIVER
Model
6805BV
Note: The switch, noise suppressor and other part configurations
may differ from country
to
country.
10
MODEL
6805BV
DESCRIPTION
May-28-'93
US
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
1
1
1
1
1
1
1
1
1
1
2
1
1
I
1
1
1
1
1
1
1
1
1
1
1
1
26
1
1
16
Front
Cap
12
0
Ring
20
AdiuSf
Sleeve
Ring
Spring
22
Clutch Cover
0
Ring
34
Flat Washer
36
Ring
36
Steel
Ball
4
Compression Spring
4
Pan
Head Screw
M5x50
[With Washerl
Gear
Housing
Leaf
spring
Steel
Ball
3
5
Spindle
Compression Spring
6
Clutch
Cam
Hook
Leaf
Spring
Name
Plate
Gear
Housing
Cover
Urethane Washer
10
Thrust
Needle
Bearing
1023
Pl"
3
5
Pan
Head
Screw
M5x40
(With Washer1
Gear
Steel
Ball
3
2
Flat
Washer
14
Sleeve
Steel
Ball
3 2
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
57
58
59
60
61
62
-
1
1
3
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
1
3
1
1
1
1
2
1
1
-
Flat
Washer
14
Compression Spring
13
6
Steel Ball
5
6
Urethane Washer
14
Flat
Washer
14
Ball
Rearing
608LB
Fan
52
ARMATURE ASSEMBLY
lWlth Item
37 401
Ball
Bearing
627LB
Rubber
Pin
4
Flat
Washer
14
Baffle
Plate
FIELD ASSEMBLY
Motor
Housing
Brush Holder
Carbon
Brush
Pan
Head
Screw
M4x14
[With Washer1
Switch
Cover
Hex
Bolt
M4x55
IWith Washerl
Rubber
Pin
4
Handle Cover
Pan Head Screw
M4x28
[With Washerl
Switch
Cord Guard
Cord
Strain
Relief
Pan
Head Screw
M4x18
(With Washerl
Reversing
Switch
0
Rinq
24
Note
The
switch
and other part
specifications
may
differ from
country
to
country
11
P
MAKlTA
LIMITED
ONE
YEAR
WARRANTY
Warranty
Policy
Every Makita tool
is
thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, return the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
This Warranty does not apply where:
0
repairs have been made or attempted by others:
0
repairs are required because
of
normal wear and tear:
0
The tool has been abused, misused or improperly maintained
;
0
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL
OR
CON-
SEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages,
so
the above limitation or exclusion may not apply to you. Some states do not allow
limitation on how long an impl~ed warranty lasts,
so
the above limitation may not apply to you.
Makita
Corporation
3-11
-8,
Sumiyoshi-cho,
Anjo, Aichi
446
Japan
8835870067
PRINTED IN JAPAN
1993
-
7
-
N
