Makita Cordless Driver Drill 6012Hd Users Manual
6012hdw e4e3b206-1ee4-4a5e-9ade-0e23cda4bfe7 Makita Cordless Drill 6012HDW User Guide |
2015-02-05
: Makita Makita-Cordless-Driver-Drill-6012Hd-Users-Manual-404869 makita-cordless-driver-drill-6012hd-users-manual-404869 makita pdf
Open the PDF directly: View PDF .
Page Count: 16
Download | |
Open PDF In Browser | View PDF |
Cordless Driver DriII MODEL 6012HD MODEL 6012HDW With Fast Charger and Carrylng Case INSTRUCTION MANUAL S PEClFICAT10NS Model 6012HD Steel Wood Wood screw Machine screw 6 5 mm 1114"l 1 5 mm 5 . 1 mm x 55 mm 13/16" x 2-118") 6 mm 1114") 1518") Battery Cartridge 9 0 0 0 Voltage 9 Nuts I :Em) 1 400 ' lrloo 1 261 mm 110-114") 1 1.6 kg 13.5 lbsl Model DC9700 Fast Charger Input output * Manufacturer reserves the right to change specifications without notice * Note: Specifications may differ from country to country. Charging time IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain. Don't use tool in presence of flammable liquids or gases. 3. KEEP CHILDREN AWAY. All visitors should be kept away from work area. Don't let visitors contact tool or extension cord. 4.STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place - out of reach of children. 5. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was intended. 6 . USE RIGHT TOOL. Don't force small tool or attachment t o do the job of a heavy-duty tool. Don't use tool for purpose not intended. 7 . DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering t o contain long hair. 8. USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. 9. DON'T ABUSE CORD. Never carry tool by cord or yank it t o disconnect from receptacle. Keep cord from heat, oil, and sharp edges. IO. SECURE WORK. Use clamps or a vise t o hold work. It's safer than using your hand and it frees both hands t o operate tool. 11. DON'T OVERREACH. Keep proper footing and balance at all times. 12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. 2 13. DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger o n switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked t o determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Don't use tool if switch does not turn it on and off. 19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. 20. REPLACEMENT PARTS. When servicing, use only identical replacement parts. VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. 3 1. SAVE THESE INSTRUCTIONS - This manual 2. 3. 4. 5. 6. 7. 8. Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger w i t h damaged cord or plug - replace them immediately. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it t o a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it t o a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 4 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5O0F1 or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. (1) Do not touch the terminals w i t h any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3)Do not expose battery cartridge t o water or rain. 6. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 5OoC (122OF). 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. ADDITIONAL SAFETY RULES 1. Be aware that this tool is always in an operating condition, because it does not have t o be plugged into an electrical outlet. 2. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 3. Hold the tool firmly. 4. Keep hands away from rotating parts. 5. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the insulated grasping surfaces t o prevent electric shock if you drill into a "live" wire. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Do not touch the drill bit or the workpiece immediately after operation: they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. 5 Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. 0 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. I Set plate To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. I f the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the batbutton tery cartridge are on the same sides as their respective markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. Press the start button (red). The charging light will come on and charging will begin. I f the charging light does not come on, press the reset button (yellow) first, then the start button (red). I f the charging light goes out within 10 seconds even after pressing the reset button and start button a couple of times, the battery cartridge i s dead. (CAUTION: Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cabridge. After charging, unplug the charger from the power source. CAUTION: .Your new battery cartridge is not charged. You will need to charge it before use. .Do not keep the button pressed in with tape, etc. or the circuit will not function properly. Also, a malfunction of the charger may result possibly causing overheating, etc. 0 6 I f you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, l e t the cartridge cool off for a while. Then re-insert it and try to charge it once more. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This i s a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Bit installation & removal CAUTION : Always set the Forward-Reverse switch lever to NEUTRAL when installing, removing or adjusting bits or accessories. 0 Chuck When installing a drill bit, notice that there are three holes in the chuck a t which you must use the key for tightening. Insert the chuck key in any of the 3 holes and turn to the l e f t (counterclockwise) to release jaws of chuck. Insert the bit and tighten with chuck key to the right. Tighten evenly a t all three holes in sequence. Tigbtten .After use, re-attachthe clip-on chuck key in the hole for it on top of the tool. / Clip-on chuck key Switch operation CAUTION : When releasing the trigger, check to be sure that it springs out to i t s original released position. The tool starts when the trigger is pulled and stops when it i s released. To reverse the rotation, use the reversing switch lever equipped just above and in front of the trigger switch. However, when changing the rotational direction, be sure the trigger switch is released (OFF) and check the rotational direction. Keep the reversing switch lever in the neutral position whenever you are not using the tool. NEUTRAL Trigger switct Drill *Punch a small hole in the metal to prevent the bit from skitterring when starting to drill a hole. 0 Use machine oil on the bit to facilitate drill ing. .Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve t o damage the tip of your drill bit, decrease your drilling performance and shorten the service of the tool. 0There is a tremendous force exerted on the tool/bit a t the time of hole break through. Grip the drill firmly and exert care when the bit begins to break through the materials. 8 Screw Match vour bit to vour screw. Phillips bits Phillips bit No. 2-65 mm is standard equipped. Select your screws and nominal diameter with the chart on the right. Item I Bit No. I No. 3 I I Nominal diameter (mm) Wood screw I I Machine screw 2.1 - 2.7 M2 - M2.6 3.1 - 4.8 M3 - M5.5 5.1 (13/64") I M6 (1/4") Slotted bits Unless you use a bit that fits properly the slot on the head of the screw, the slot will be damaged and the screw will not fasten. If the bit fails to match the slot, use a grinder or some such tool to trim the bit to fit the slot. NOTE : Rest the tool for 15 minutes when changing battery for continuous operation. 9 Speed changeover .To change the speed, turn the speed change knob 180" while the drill is running. Be sure that the speed change knob i s turned to the correct speed setting before you begin operation. See arrow indication. Use the right speed for the job. Fastening torque adjustment Just turn the fastening torque adjust knob on the tool in order to select any of 5 different fastening torques. Make sure that the arrow points to the right torque before you begin the job. Torques are numbered from 1 to 5 in the order of strength. Set to 5 for use as a drill. The torque setting for number 5 is designed for drilling, and to protect the motor from burn out, so it can slip when a very high torque is applied. Grip .The grip shown on the right is recommended. However, grip the tool firmly with both hands when drilling a largediameter hole. 10 Fastening torque adjust knob I Arrow *The hole on the heel of the tool is a convenient way to carry it by a cord, hook or other means. I 11 ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Fast charger Model DC9700 0 Makita Battery cartridge 9000 (9.6 V) 1 hour fast charge nickel cadmium battery Part No. 632007-4 0 Bits 1 I I #5F #7F Square drill b i t 0 Battery holster Holds with extra battery Part No. 823033-3C 12 Charger 1 2 V for car Model DC9112 0 Chuck key S10 Part No. 763419- 1 0 Rubber pad assembly Part NO. 123001 - 2 0 Wool bonnet Part No 743401 -6 I I Slotted 0 I 784010-0A 784011-0A 784606-0A 0 Foam polishing pad Part No. 743023-2 0 Tool holster has some bits storage space. Use holster t o carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-36 Part No. 823033-3E (Genuine leather) 0 Tool carrying case Part No. 823085-7 (Steel case) Part No. 824145-8 (Plastic case) 13 Feb 19 86 EN CORDLESS DRIVER DRILL Model 6012HD Note: The switch and other part configurations may differ f r o m country to country 14 MODEL 6012HD Feb-19-86 EDDESCRIPTION EN DESCRIPTION ",',;I MACHINE ______ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Pan Head Screw M5x18 Drill Chuck S 1 0 Spindle Pi" 3 Ball Bearinq 6000LLB STOPRing E 9 Compresslo" Spr,ng 10 Thin Washer 1 0 Spur Gear 7 8 Ring 16 Spur Gear 9 3 Thin Washer 1 0 Compression Spring 1 0 Flat Washer 5 Plane Bearing 5 Shift Knob Supporler compress~o" spr ny 3 S ~ e e Ball l 4 8 Shift Knob Retaining Ring S 6 Flat Washer 1 4 Ball Bear ng 626LLB F l a t Washer 6 Spur Gear 8 9 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 54 55 - 4 1 1 Steel Ball 4 8 Clutch Cam Conical Compression Spring 1 6 - 2 1 I 08% 1 1 1 1 1 1 Thrust Needle Gauge 1 0 2 3 Flat Washer 8 Slider P," 3 Gear 1 2 - 2 8 I 1 1 1 1 1 1 1 8 1 1 1 1 Plane Bearing 4 Shifter Leaf S p m g Holder 6 DC Motor 9 6 V Switch Housing Set lWith Item 551 Battery 9000 Name Plate Pan Head Screw M 4 x 2 2 IWith Washer1 Sleeve 5 set Plate Compression Spring 8 Housing Set l W i f h Item 401 - Now The Switch and other part specifications may differ from c o u n t r y to Country 15 The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under ”Tools-Electric’: MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not apply where: e repairs have been made or attempted by others: e repairs are required because of normal wear and tear: e The tool has been abused, misused or improperly maintained, e alterations have been made to the tool. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE O F THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES O F “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE.” AFTER THE ONE-YEAR TERM OF THIS WARRANTY. This Warranty gives Y O U specific legal rights, and you may also have other rights which vary from state to state. Some states d o not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply t o you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446 Japan 883544IO65 PRINTED IN JAPAN 1993 - 7 - N
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Modify Date : 2002:07:03 12:30:45-07:00 Create Date : 2002:07:03 12:30:28-07:00 Producer : Adobe PDF Library 4.0 Creator : Acrobat Capture 3.0 Style : Searchable Image (Exact) Page Count : 16EXIF Metadata provided by EXIF.tools