Manco 606C 14 User Manual MASTER OF MOTION GO CART Manuals And Guides L0411313
SEARS Gokarts/Minibikes Manual L0411313 SEARS Gokarts/Minibikes Owner's Manual, SEARS Gokarts/Minibikes installation guides
User Manual: Manco 606C-14 606C-14 MANCO MASTER OF MOTION GO-CART - Manuals and Guides View the owners manual for your MANCO MASTER OF MOTION GO-CART #606C14. Home:Toys & Games Parts:Manco Parts:Manco MASTER OF MOTION GO-CART Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Assembly Instructions Model 6XX The following instructions are to complete the assembly of your Manco Fun Kart using the component parts and hardware that were packaged with the kart. Carefully read these instructions completely before starting the assembly. torque to be applied to tighten them securely. Safety Make sure that the nuts and heads of the bolts are fully engaged with the sarface of the bushings. Then apply a final tightening torque. Insert the special flag mounting bolt (PN 11361) into the motmting tab on the rear loop of the frame placing a 1/2 inch washer (PN 9022) under Tools Seat and Headrest the head of the bolt. Place a 1/2 inch nut (PN1012) on the end of the bolt and hand tighten. Insert the flag mounting shaft through the mounting bolt allowing approximately 1/2 inch of the shaft to protrude past the end of the bolt. Use wrenches to required for assembly Pad Assembly (2) (2) (2) (1) i_ 9/16 inch wrenches 3/4 inch wrenches 7/16 inch wrenches 3/8 inch wrench Warning: Risk of death or Bodily Injury. The Brush Bars, and the Seat and Shoulder Belt are critical Operator / Passenger on this kart. operate of the satbty Do not attempt system Bar have been Shoulder Read and :follow instructions the engine manual. Engine Fluids Belt Assembly in Position the shoulder belt Assembly the over head bar assembly on the kart using four 3/8 x 16 x 3.5 inch long bolts (PN 2386) and 3/8 inch nuts (PN 9085). Fully tighten all of the brush bar and headrest mounting bolts at this time. These fasteners use locking nuts and require a high level of PN 13472 securely tighten the nut and bolt to fix the position of the flag properly Position the rear bar assembly on the frame using four 3/8 x 16 x 3.5 inch long bolts (PN 2386) and 3/8 inch nuts (PN 9085) to hold it in place. Do not tighten these fasteners completely at this time. Position support bar using four 114 x 20 x 5/8 inch long bolts (PN 1876). Tighten these fasteners securely at this time. to the kart until these components installed. Brush parts Assemble the rear pad of the seat to the seat frame using two 1/4 x 20 x 5/8 inch long bolts (PN 1876). Assemble the head rests to the Fla_ Assembly mounting tab against the support tab on the rear bar assembly with a 1/2 washer (PN 9022) between the tabs. Use a 1/2 x 13 x 1.5 inch long bolt (PN 9188) and 1/2 inch nut (PN 1012) to secure these two tabs together. Tighten the bolt and nut until the two tabs make contact with the washer between them but do not over tighten. When properly assembled, the belt tab should be able to rotate freely on the mounting bolt. Follow this process for both the Operator and Passenger belts. Remove oil fill plug and fill the engine crankcase with 20 oz of 30W type SF or higher motor oil. Replace and securely tighten the oil fill plug. Fill the fuel tank with regular grade clean, unleaded gasoline. Do not use premium grade gasoline, gasohol or diesel fuel. 2386 "7 / 2386 \ 8188 1876 \ 11361 9022-- 8 9028 QTY (3) 9085 I012 QTY E 8386 QTY (8) 3/8-16 X 3,500 QTY (3) 9103 X 2,00 9057 (8) 3 3 QTY (3) 1/4-20 8 11361 QTY FLAG (i) BOLT 9188 QTY (2) 1/8-13 X 1,50 QTY (3) 1876 QTY (6) i/4-20 X ,625 13472
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Apr 20 15:28:06 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools