Mandolyn Electronic Technology RC270 Indoor Switch Receiver for Appliances User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	161676
Application ID	oUQsG1s3OHZLZ7BfqI/t/w==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.17kB (577111 bits)
Date Submitted	2001-07-26 00:00:00
Date Available	2001-07-26 00:00:00
Creation Date	2017-12-25 14:11:17
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-25 14:11:17
Document Title	users manual
Document Creator	C:SCANDALLSCANDALL.EXE

MARSTECH LIMITED
EXHIBIT A
(FCC Ref. 2.1033(b)(5))
"Installation and Operating Instructions
Fumished to the User"
Mandolyn/RC270 and RC27OD EXHIBIT A
FCC ID: PLJRC270
Marstech Report No. 21 163D
WIRELESS REMOTE CONTROL USER MANUAL
TR300 Transmitter
RC270 Indoor Receiver for Appliance
Introduction
The TIUOO Transmitter is designed to control our lndoor Receiver RC270. You can use this
Transmitter to control the Receivers RC270 for any plug-in electrical appliances as Well as
lighting devices.
The Transmitter has 4 channels, which can control up to 4 receivers.
intelligent Code setting and Learning function means there is no complicated setting of code
switches and interference by other remote control system is nearly impossible.
Operation of this Remote control is simple and easy. To obtain fullest utilization out of this
product, please read and follow the instructions listed below carefully.
TRANSMITTER TR300 RECElVER RC270
Menutl
own K-Y
I_=D lNDiCA70R
LED mum.
RC-402
FCC ID: PLIRCZ7O
Marstech Report No. 21 163D
EXHIBIT A(l)»1
The system code and channel number of the Receivers will be retained if they are unplugged from
the power outlet for less than 10 minutes. If the Receivers have been unplugged for too long
duration, the above learn ’ procedures needs to be performed againr
DO NOT press the RESET button of the transmitter again after setting up the Receivers unless
you suspect that the Remote Control is interfered by other signals. This will generate a new
system code, and all Receivers needs to perform the learn 'procedure again.
To avoid interference, do not put the Receivers along side one another. A minimum distance of
18 inches (05 meter) is recommended.
OUTPUT INDICATOR OF RECEIVER
' For RC270 appliance receiver, the green LED will light ifthe output is turn on.
OPERATION
Control using button on the Receivers
- A short press ofthe ON/OFF button will toggle the plugged—in appliance/ lamp on and off.
Remote Control Operation
With the TR300 Transmitter, you can control up to 4 Receivers using RF remote control.
. To turn on or off the output of the Receiver(s), press the ON or OFF button of the assigned
channel respectively.
Notes:
Please note that there is a data backup circuitry inside the Receiver to remember the code setting
during the period without AC power. Therefore, there is a possibility that, in some rare
circumstances, the Receiver may become unable to operate after AC failure. To solve this
problem,just remove the Receiver from the AC power for 6 hours and try the setup procedures
again.
Technical Specifications
RC27O Appliance Receiver
Ratings: 120V 60Hz
Transmission Range: 25 meters in open area
Maximum Load: ISOOW (15A) resistive
Transmitter
Power Source: 9V Battery
System Code: 4,096 combinations
This device complies with Part 15 ofthe FCC Rules Operation is subjected to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interence recived, including interference that may cause undesired operation.
EU 1 [ON CONFIGURATION
Transmitter TR300
ON The 4 ON button will turn on the receiver of the respective channel
OFF The 4 ON button will turn on the receiver of the respective channel
BRIGHT Increase the brighmess of the plugged-in lamps (only applicable for our other
UPM "Brand Dimmer Receivers RC270D)
DIM Decrease the brightness of the plugged-in lamps (only applicable for our other
UPM " Brand Dimmer Receivers RC270D)
RESET (located inside the battery compartment) Generate a new System code
Appliance Receiver RC27O
LEARN Learn the System Code and Channel number assigned by the Transmitter
ON/OFF Turn on/ofl" the plugged-in devices manually
Note: LEARN pracedwe as described below must be performed before the remote central/“auction
will work.
Batterv Installation & Setting Up of Remote Transmitter TR300
- Open the battery cover at the back of the Transmitter.
0 Install one 9V battery (included) into the battery compartment. Make sure the battery is in
the right polarities. Otherwise, it may result in short-circuit and damage the device.
0 If you wish, press the RESET button once to generate a unique System code so that this set of
remote control will not be interfered by other similar systems nearby.
- Put the battery cover back onto the Transmitter.
- Press any button to ensure that it is working properly (which is indicated by the flashing
LED).
Setting Up oflndoor Receiver RC270
- Plug the Receiver into the wall socket.
0 Plug an electrical appliance or a lamp into the output socket of the Receiver. Make sure the
plugged-in device is turned on.
o Press the ON/OFF button on the Receiver. The plugged-in appliance or lamp should turn on,
indicating everything is ready. Push the button again to turn ofi‘the appliance.
c To match the system code and assign a channel to the Receiver, press and hold the LEARN
button on the Receiver while pressing and holding the ON button ofyour desired channel
(e.g., CH.l ON) ofthe Remote Transmitter TRJOO. The Receiver will 1‘eam"the assigned
channel automatically and the appliance/ lamp will turn on, Release the LEARN button.
0 To check whether the Receiver is now responding to the assigned Channel, try turning on/off
the plugged-in device by pressing the ON or OFF button of the assigned channel on the
Transmitter.
Repeat the above procedures if you have more than I Receiver.“ The Receivers can be set to same
channel or different channels, depending on whether you want to control the Receivers together
or separately.
Period of Keyed Modulated RF - Carrier
Model : TR300
RC270/RC270D
Carrier Frequency: 433.92MHz
Bit Rate: 521 bits / second
Encoding: Pulse width modulation
1 pulse of 1.28 ms low, 0.64 ms high for logic I
l pulse of 0.64 ms low, 1.28 ms high for logic 0
Word Format: l/3bit + 20 bits / word
Operating Period: One transmission of 4 words each time (depends on user)
Specification:
Tl M
Frequency Range : 433 .92MHZ 433.92MHZ
Number of Channel : 1 1
Antenna : Printed Antenna Printed Antenna
Power Supply : 9V 120V AC
Transmitter Duty : Intermittent N/A
(User Controlled)
WIRELESS REMOTE CONTROL USER MANUAL
TR300 Transmitter
RC270D Indoor Dimmer Receiver for Lighting
Introduction
The TR300 Transmitter is designed especially to control all our Indoor Dimmer Receiver
RC27OD. With its dual mode (on/off and dimmer functions), you can use this Transmitter to
control the Receivers for switching on or off, dim or bright the pluggedAin lamp.
The Transmitter has 4 channels. which can control up to 4 receivers.
intelligent Code setting and Learning function means there is no complicated setting of code
switches and interference by other remote control system is nearly impossible.
Operation of this Remote control is simple and easy. To obtain fullest utilization out of this
product, please read and follow the instructions listed below carefully.
TRANSMITTER TR300 RECEIVER RCZ70D
mmKIy
LE: INmCATDR
LED mania
RC-402
rcc ID: PLJRC270
Marslech Report No. 21 163D
EXHIBIT A(l)-2
BUTTON CONFIGURATION
Transmitter TR-SOZS
ON The 4 ON button will turn on the receiver ofthe respective channel
OFF The 4 ON button will turn on the receiver ofthe respective channel
BRIGHT Increase the brightness of the plugged~in lamps (only applicable for Dimmer
Receivers RC27OD)
DIM Decrease the brightness ofthe plugged-in lamps (only applicable for Dimmer
Receivers RC270D)
RESET (located inside the battery companment) Generate a new System code
Dimmer Receiver RC270D
LEARN Learn the System Code and Channel number assigned by the Transmitter
ON/OFF DIM Control the on/offand brightness ofthe plugged-in lamps
SYSTEM SETUP
Note: LEA RN procedure as described below must be performed before the remote control/auction
will work.
Batterylnstallation & Settinc'= Up of Remote Transmitter TR300
0 Open the battery cover at the back of the Transmitter.
- Install one 9V battery (included) into the battery compartment. Make sure the battery is in
the right polarities. Otherwise, it may result in short-circuit and damage the device.
0 If you wish. press the RESET button once to generate a unique System code so that this set of
remote control will not be interfered by other similar systems nearby.
. Put the battery cover back onto the Transmitter.
- Press any button to ensure that it is working properly (which is indicated by the flashing
LED).
Setting Up of Indoor Receiver RC270D
- Plug the Receiver into the wall socket.
. Plug a lamp (with a wattage of300W or less) into the output socket ofthe Receiver. Make
sure the s“. itch ofthe lamp is turned on. '
- Press the ON/OFF button on the Receiver. The lamp should turn on, indicating everything is
ready. Push the button again to turn offthe lamp.
0 To match the system code and assign a channel to the Receiver, press and hold the LEARN
button on the Receiver while pressing and holding the ON button ot'your desired channel
(e.g., CH.1 ON) of the Remote Transmitter TR300.. The Receiver will feam " the assigned
channel automatically and the lamp will turn on. Release the LEARN button.
- To check whether the Receiver is now responding to the assigned Channel, try turning on/off
the plugged-in lamp by pressing the ON or OFF button ofthe assigned channel on the
Transmitter.
Repeat the above procedures if you have more than i Receiver. The Receivers can be set to same
channel or different channels, depending on whether you want to control the Receivers together
or separately.
The system code and channel number of the Receivers will be retained if they are unplugged from
the power outlet for less than IO minutes. [fthe Receivers have been unplugged for too long
duration, the above l‘earn ’procedures needs to be performed again.
DO NOT press the RESET button of the transmitter again afier setting up the Receivers unless
you suspect that the Remote Control is interfered by other signals. This will generate a new
system code. and all Receivers needs to perform the learn ’procedure again.
To avoid interference. do not put the Receivers along side one anotherr A minimum distance of
18 inches (0.5 meter) is recommended.
OUTPUT INDICATOR OF RECEIVERS
~ The orange indicator lamp will glow if the light is connected and turned ont and the Dimmer
Receiver itself is turned ofi'. When you turn on the Dimmer Receiver, the orange indicator
will turn off.
OPERATION
Control usino button on the Receivers
- A short press ofthe ON/OFF button will toggle the plugged-in lamp on and off.
- Press and hold the ON/OFF button ofthe Receiver will cycle the lamp through various
intensity
Remote Control Operation
0 With the TR300 Transmitter, you can control Dimmer Receiver RC27OD using RF remote
control.
- To turn on or offthe plugged-in lamp(s) ofthe Dimmer Receiver, press the ON or OFF
button of the assigned channel respectively.
a To dim or bright the plugged~in lamp(s) ofthe Dimmer Receiver, first press the ON or OFF
button ofthe assigned channel once. Then, press the DIM or BRIGHT button to adjust the
brightness.
If you want to adjust the brightness of the channel that you havejust used previously, you can
use the DIM or BRIGHT button directly to adjust the brightness without pressing the ON or
OFF button in advance
Notes:
Please note that there is a data backup circuitry inside the Receiver to remember the code setting
during the period without AC power. Therefore, there is a possibility that, in some rare
circumstances, the Receiver may become unable to operate afier AC failure. To solve this
problem,just remove the Receiver from the AC power for 6 hours and try the set-up procedures
again.
The Dimmer Receiver RC270D is only intended to control lightings only (max. 300W). Do not
plug any electrical appliances other than lamps into the Dimmer Receiver RC27OD. Otherwise, it
may result in damages to the Receiver as well as the plugged-in appliances.
Tech I S ecifiearions
RC270D Dimmer Receiver
Ratings: 120V 60Hz
Transmission Range: 25 meters in open area
Maximum Load: 300W incandescent lamp or Halogen lamp (120V)
Transmitter
Power Source: 9V Battery
System Code: 4,096 combinations
This device complies with Part 15 of the FCC Rules Operation is subjected to the following two conditions:
1. this device may not cause harmful interference, and
Zr this device must accept any interence recived, including interference that may cause undesired operationr

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.1
Linearized                      : No
Page Count                      : 9
Create Date                     : Thu Jun 28 13:17:27 2001.
Producer                        : Pixel Translations (PIXPDF Ver.1.38)
Creator                         : C:SCANDALLSCANDALL.EXE

EXIF Metadata provided by EXIF.tools