Mandolyn Electronic Technology TR300 Wireless Remote Control Transmitter User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	161686
Application ID	4Hn1MufuRplJgDMbPzF7jQ==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.27kB (290937 bits)
Date Submitted	2001-07-26 00:00:00
Date Available	2001-07-26 00:00:00
Creation Date	2017-12-25 14:10:57
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-25 14:10:57
Document Title	users manual
Document Creator	C:SCANDALLSCANDALL.EXE

MARS TECH LIMITED
EXHIBIT A
(FCC Ref. 2.1033(b)(5))
"Installation and Operating Instmctions
Furnished to the User"
Mandolyn/TR300 EXHIBIT A
FCC ID: PLJTR300
Marstech Report No. 21245D
WIRELESS REMOTE CONTROL USER MANUAL
TR300 Transmitter
RC270D Indoor Dimmer Receiver for Lighting
Introduction
The TRSOO Transmitter is designed especially to control all our Indoor Dimmer Receiver
RC270D. With its dual mode (on/offand dimmer functions). you can use this Transmitter to
control the Receivers for switching on or off, dim or bright the plugged-in lamp.
The Transmitter has 4 channels, which can control up to 4 receivers
Intelligent Code setting and Learning function means there is no complicated setting of code
switches and interference b) other remote control system is nearly impossible,
Operation ofthis Remote control is simple and easy. To obtain fullest utilization out ofthis
product, please read and follow the instructions listed below carefully.
TRANSMITTER TR300 RECEIVER RCZ7OD
mm m
_E: "\§lCATC~i
LED lndicaw'
FCC ID: PLJTR300
Marstech Report No. 2I245D
EXHIBIT A-I
BUTTON CONFIGURATION
___________________—
Transmitter TR-SOZS
ON The 4 ON button will turn on the receiver ofthe respective channel
OFF The 4 ON button will turn on the receiver ofthe respective channel
BRIGHT Increase the brightness ofthe plugged-in lamps (only applicable for Dimmer
Receivers RC270D)
DIM Decrease the brightness ofthe plugged-in lamps (only applicable for Dimmer
Receivers RC270D)
RESET (located inside the battery compartment) Generate a new System code
Dimmer Receiver RC270D
LEARN Learn the System Code and Channel number assigned by the Transmitter
ON/OFF DIM Control the on/offand brightness ofthe plugged-in lamps
SYSTEM SETUP
Note: LEA RN procedure as described below must be per/armed before the remute contlalfuncrion
will work.
Batten Installation & Settinu Up of Remote Transmitter TR300
a Open the battery cover at the back ofthe Transmitterl
. Install one 9V battery (included) into the battery compartment. Make sure the battery is in
the right polarities. Otherwise, it may result in short-circuit and damage the device.
0 Ifyou wish. press the RESET button once to generate a unique System code so that this set of
remote control will not be interfered by other similar systems nearby.
0 Put the battery cover back onto the Transmitter.
o Press any button to ensure that it is working properly (which is indicated by the flashing
LED).
Setting U9 oflndoor Receiver RC27OD
- Plug the Receiver into the wall socket.
0 Plug a lamp (with a wattage of300W or less) into the output socket ofthe Receiver. Make
sure the snitch of the lamp is turned on ~
- Press the ON/OFF button on the Receiver. The lamp should turn on, indicating everything is
ready. Push the button again to turn offthe lamp.
To match the system code and assign a channel to the Receiver. press and hold the LEARN
button on the Receiver while pressing and holding the ON button ofyour desired channel
(e.g., CHll ON) ofthe Ramote Transmitter TR300.. The Receiver will Tearn"the assigned
channel automatically and the lamp will turn on. Release the LEARN button.
To check whether the Receiver is now responding to the assigned Channel, try turning on/off
the plugged-in lamp by pressing the ON or OFF button ofthe assigned channel on the
Transmitter.
Repeat the above procedures if you have more than 1 Receiver. The Receivers can be set to same
channel or different channels. depending on whether you want to control the Receivers together
or separately.
The system code and channel number ofthe Receivers will be retained ifthey are unplugged from
the power outlet for less than l0 minutes. lfthe Receivers have been unplugged for too long
duration. the above learn 'procedures needs to be performed again.
DO NOT press the RESET button of the transmitter again afier setting up the Receivers unless
you suspect that the Remote Control is interfered by other signals, This will generate a new
system code. and all Receivers needs to perform the learn 'procedure again,
To avoid interference, do not put the Receivers along side one another. A minimum distance of
18 inches (05 meter) is recommended.
OUTPUT INDICATOR OF RECEIVERS
o The orange indicator lamp will glow ifthe light is connected and turned on, and the Dimmer
Receiver itself is turned off. When you turn on the Dimmer Receiver, the orange indicator
will turn off.
OPERATION
Control using button on the Receivers
. A short press ofthe ON/OFF button will toggle the plugged—in lamp on and oft".
0 Press and hold the ON/OFF button ofthe Receiver will cycle the lamp through various
intensity.
Remote Control Operation
- With the TR300 Transmitter, you can control Dimmer Receiver RC270D using RF remote
control.
- To turn on or offthe plugged-in lamp(s) ofthe Dimmer Receiver. press the ON or OFF
button of the assigned channel respectively.
a To dim or bright the plugged-in lamp(s) ofthe Dimmer Receiver, first press the ON or OFF
button ofthe assigned channel once. Then, press the DlM or BRIGHT button to adjust the
brightness,
lfyou want to adjust the brightness ofthe channel that you havejust used previously, you can
use the DlM or BRIGHT button directly to adjust the brightness without pressing the ON or
OFF button in advance.
Notes:
Please note that there is a data backup circuitry inside the Receiver to remember the code setting
during the period without AC power. Therefore, there is a possibility that, in some rare
circumstances, the Receiver may become unable to operate afler AC failure, To solve this
problem,just remove the Receiver from the AC power for 6 hours and try the set-up procedures
again.
The Dimmer Receiver RC270D is only intended to control lightings only (max. 300W), Do not
plug any electrical appliances other than lamps into the Dimmer Receiver RC270D, Otherwise. it
may result in damages to the Receiver as well as the plugged-in appliances.
Technical Specific-ad ns
RC270D Dimmer Receiver
Ratings: 120V 60Hz
Transmission Range: 25 meters in open area
Maximum Load: 300W incandescent lamp or Halogen lamp (lZOV)
Transmitter
Power Source: 9V Battery
System Code: 4,096 combinations
This device complies with Pan 15 ofthe FCC Rules Operation is subjected to the following two conditions:
1. this device may not cause harmful interference, and
1 this device must accept any interence recived, including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.1
Linearized                      : No
Page Count                      : 5
Create Date                     : Thu Jun 28 14:14:03 2001.
Producer                        : Pixel Translations (PIXPDF Ver.1.38)
Creator                         : C:SCANDALLSCANDALL.EXE

EXIF Metadata provided by EXIF.tools