Mandolyn Electronic Technology WS2635 Weather Station Receiver User Manual WS635 MANUAL two

Mandolyn Electronic Technology Inc. Weather Station Receiver WS635 MANUAL two

Users Manual

P.14P.9P.13 P.15P.12P.10P.11  RAINFALL & ANEMOMETER DISPLAY  WEATHER FORECAST & DISPLAY PRESSURE HISTORICAL BAR GRAPH FCC STATEMENT  MOON PHASES   TEMPERATURE & HUMIDITY DISPLAY  TEMPERATURE & HUMIDITY TREND  TEMPERATURE ALARMThroughout the 28 days of the lunar month, the aspect of the moon changes. Indeed, the moon, being spherical, is always half lightened up by the sun. As the moon rotates around the Earth, the appearance of its lightened side changes continuously. This phenomenon creates moon phases. The moon phase on your MeteoClock is automatically updated according to the year/ month/day.1.  New Moon     2.  Young Crescent    3.  First Quarter    4.  Waxing Gibbous    5.  Full Moon     6.  Waning Gibbous    7.  Last Quarter    8.  Old CrescenCheck Inside Temperature and humidityAfter inserting the batteries, the local temperature and humidity will be displayed [*].Check Outside Temperature & Humidity1. Press CHN [4] to toggle between the data of your various remote sensors: Outside 1 (channel 1), Outside 2 (channel 2) and Outside 3 (channel 3). Temperature and humidity readings will alternate on the receiver.Note: if you do not have any additional sensors, please disregard this function. °C or °F Temperature Display2. Toggle between °C and °F by pressing Snooze [5] in Clock 2 mode. Min and Max Temperature & Humidity            3. Press MINUTE/- [3] in Clock 1 mode to display minimum temperature and humidity records. 4. Press HOUR/+ [2] in Clock 1 mode to display maximum temperature and humidity records.Display HI & LO"Hi" and "Lo" displayed onscreen mean that the temperature or humidity is outside the range of specication.Insid e/ Outside  Temperature  Humidity   Display  Insid e   > +55°C  > 95%  HI  Insid e   < - 20°C  < 15%  LO  Outside   > +70°C  > 95%  HI   Outside   < -  30°C  < 15%  LO  The trend indicator shows the trend of temperature & humidity determined by the particular sensor in the past half hour interval.You can set high temperature or low temperature alarms for one local channel and for one remote channel.Local temperature alarm1.  Scroll to temperature alarm mode by using MODE (Inside).2.  The default value 14°C or existing preset will ash.3.  Press Hour/+[2] or Minute/– [3] keys to set the temperature limit value.4.  Press Snooze [5] key continuously to scroll and select the high temperature alarm , low temperature alarm (      )   or disable the alarm (      ) function (blank).5.  Press mode [1] to save your settings.Outdoor temperature alarm1.  Scroll to remote channel temperature alarm mode by using mode [1].2.  Press CHN [4] to select the channel of the desired transmitter.3.  The default value 14°C or existing preset will ash.4.  Press Hour/+[2] or Minute/– [3] keys to set the temperature limit value.5.  Press Snooze [5] key continuously to scroll and select the high temperature alarm (       ) , low temperature alarm (      )   or disable the alarm function (blank).6.  Press mode [1] to save your settings.When the temperature alarm soundsThe icon        signals that the temperature has exceeded the preset temperature limit.a.  Press any key to stop temperature alarm.b.  If no key is pressed, the temperature alarm will automatically stop itself after one minute.c.  Once triggered, temperature alarm comes on as a distinctive sound, dierent to that of Alarm1 and Alarm2.RainfallThe rainfall can be displayed in mm or in, moreover it can show the rainfall record in total, at last hour, today & yesterday.Change the display unitPress the Min key at clock 1 can change the display unit of rainfall and wind speed.Display the rainfall recordTo display the last hour, today &yesterday’s rainfall Press the Hour key at clock 1 to change the rainfall recordWind speedThe wind speed can be displayed in km/h, mph. Change the display unitPress the Min key at clock 1 can change the display unit of rainfall and wind speed.Animated weather forecast symbolsThis weather station is capable of detecting barometric pressure changes, and based on the data collected, can predict the weather for the next 12 to 24 hours. The eective range covers an area of 30 – 50km.Storm Alert* The storm symbol will ash to warn of a thunderstorm.* It is activated when pressure falls/rises and temperature plunges.About Snow and Freeze Warning* The snow symbol will ash to warn that it might snow.* Activated when the temperature of Channel 1 is between -1.9 °C & +2.9 °C.* The snow symbol will appear solid when the temperature of channel 1 falls below - 1.9 °C, and it is freezing.Note:* The remote sensor set at channel 1 displays the weather forecast icons (as well as the trend indication). Please place it outdoors. REMARKS:After having completed the settings of your weather station, please discard the readings of the weather forecast for the next 12-24 hours. This will allow sucient time for the Weather Station to operate at a constant altitude and therefore result in a more accurate forecast.Absolute accuracy cannot be guaranteed regarding weather forecasting.The weather forecasting feature is estimated to have an accuracy level   of about 75% due to the varying areas the Weather Station has been   designed to be used in.If the Weather Station is moved to another location signicantly higher or lower than its initial standing point (e.g. from ground oor to 1st oor of a house), remove the batteries and reinsert them after about 30 seconds. By doing this, the Weather Station will mistakenly consider the new location as a possible change in air pressure. Again, discard the weather forecasts for the next 12-24 hours as to allow time for operation at a constant altitude.Pressure trend The trend pointer displayed at  indicates the trend of the barometric pressure.Indicates that the barometric pressure trend is increasing.  Indicates that the barometric pressure trend is steady.Indicates the barometric pressure trend is decreasing.Altitude settingThe altitude setting can calibrate the pressure reading of main unit to it’s position. It is because the exact pressure reading will be aected with the altitude of the main unit.1After Alarm setting, and then press mode key can go to Altitude setting mode2 Press Max and Min key to increase and decrease the altitude reading one at a time3 SNOOZE key is to select pressure (hPa & inchHg) altitude (m & feet) units in altitude setting mode.NoteSince the default altitude is zero (sea level), after reset pressure display shows absolute pressure. To see the relative pressure, user must enter the altitude for his/her current location.  The bar graph lets you see the pressure trend over a period of 12 hours. The bar graph will show the pressure trend.Note: The weather forecast, by the means of the animated icons, depends on the evolution of the barometric pressure. By consulting the barometric pressure historical graph you can evaluate the likeliness or the strength of the weather forecast currently displayed. For example, if the pressure has steadily increased over the past 12 hours but decreases slightly in the next 3 hours, the weather station might forecast rain, but you could expect the probability of rain to remain low. On the other hand, if you observe a sudden and large shift in pressure, the weather forecast is more likely to be extreme. For example, if the forecast is rain, and you observe a large and sudden downward shift of pressure, the rain is likely to be heavy. The statement required by 15.105 is as follows:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Moon Phase Display 23Sunny Cloudy Raining Snowing Freeze Warning Storm Alert SPECIFICATIONSWeather Station Receiver WS635Battery Type: 3 X1.5V AA batteriesMeasurument  Range  Resolution  Temperature Inside -20 oC to +70 oC0.1 oCTemperature Outside -30 oC to +70 oC 0.1 oC Humidity Inside/Outside  15% to 95%   1% Pressure 800mbar to 1100mbar 1mbar Wind Direction  16 directions  22.5° Wind speed    0km/h-127.5km/h  0.5 km/h Rain Volume   -  0.2mm Weather Station Transmitter WT460Battery Type:                       2 X1.5V AA batteries Temp. Range:                    -30 oC to + 70 oCHumidity Range:                15% to 95%Transmission Frequency:  433.92MHzTransmission Range:         Up to 40 meters in open area.Statement required by 15.19 and RSS210This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.Operation is subject to the following two conditions:(1)  this device may not cause harmful interference, and (2)  this device must accept any interference received, including interference that may cause undesired operation. FCC STATEMENTWarning: Any changes or modications made to this equipment not expressly approved by Mandolyn Electronic Ltd. may void the FCC authorization to operate

Navigation menu