Mandolyn Electronic Technology WS928 Weather Station Receiver User Manual WS928 WT440H UPM Manual ENG

Mandolyn Electronic Technology Inc. Weather Station Receiver WS928 WT440H UPM Manual ENG

User Manual

Press and hold MODE for 3 seconds to Clock Setting mode Press MODE again to Month/Date setting mode Press HOUR/+/MAX to set month Press MINUTE/-/MIN to set date Press MODE to enter Year setting Press HOUR/+/MAX or MINUTE/-/MIN to adjust Year Weekday is automatically determined from the year/month/day settingMONTH & DATE, YEAR SETTINGabcdfP.6WS928+WT440HWireless Weather Station KNOW YOUR PRODUCT button placement162345Minute/-/Min: shows minimum temperature; adjusts clock, alarm, date & year and temperature alarm valuesSnooze/Mode: scrolls through Clock 1 & 2, Alarm 1 & 2, Date & Year, and Temperature Alarm(high & low) mode; snooze for alarmLCD displayON/OFF /(C/F): toggles between C and F, 12 and 24 hour format, Alarm 1 & 2 on and off; disables (resets) high & low temperature alarmsChannel: scrolls through remote channels Outside, Outside 2 and Outside 3); scrolls through local and remote channels (Outside, Outside 2 and Outside 3) in (high & low) temperature alarm mode; activate learn processHour/+/Max: shows maximum temperature; adjusts clock, alarm, date & year and temperature alarm valuesP.1P.5 P.7P.4P.8Inside temperature / humidity trend symbolP.2 or will flash, and the sound volume will gradually from low to highPress SNOOZE to snooze the alarm for 5 minutes, after that the alarm will sound again Press ANY other key will shut off the alarm. Without interruption, the alarm will shut off automatically after one minuteALARM SETTINGabcP.37101189SET: enter to House code and Channel setting modeC/F: change between °C or °F, change channel and house code Battery compartmentLCD displayWall mount holder &table stand7899Scroll to Alarm1 mode (Alarm2 mode) using MODEPress HOUR to set hourPress MINUTE to set minutePress ON/OFF/(C/F) to set alarm on or offWhen the alarm is set ON, the bell symbol / will appear1234511Press and hold MODE for 3 seconds to enter the clock setting mode (the CLOCK 1 symbol appears and the time will flash)Press HOUR to set the hour and MINUTE to set the minute; Press ON/OFF(C/F) during clock setting, to change between 12 and 24 hour display. Do not press any key for 1 minute to finish clock settingScroll to Clock 2 mode using MODEPress + or - key to change the timeiiiiiiivviv 61234511ivviiiiii21OUT134OUT141234b#eWS928 receiverInside temperature / humidity readingOutside temperature readingOutside humidity readingOutside temperature trend symbolOutside humidity trendPressure trend symbolPressure readingMoon phase Comfort level iconWeather forecastsymbolsMonth/Day, YearAlarm clock ClockWeekdayTemperature/ pressure historicalbar graphClock 1 SettingClock 2 SettingAlarm 1and Alarm 2 settingWhen alarm soundsdebfcf#aThe colon symbol " " appears if date value is 2-digit (e.g. 13, 26...) **MANUAL CLOCK SETTINGREAD THIS BEFORE YOU BEGINInsert batteries into the remote transmitter(s) first, and then the receiver.For the best operation, Although remote transmitters are weather resistant, it is recommended to place it away from direct sunlight, rain or snow. This will help to make condition readings more accurate. Place the receiver and remote transmitter(s) close together. This will ensure that the receiver synchronizes with remote transmitter(s).Place the remote transmitter(s) outdoors within an effective transmission range.31*2The transmission range can be affected by the dense walls or electronic interference in between the receiver and transmitter. Try various set-ups for best results. #2463 5 71111%18GETTING STARTEDRemove battery cover and insert 2 AA size batteries. Insert between terminals observing proper polarity then replace cover.1Remove battery cover and insert 2 AA size batteries to start setup. The HOUSE CODE will flash for 8 secondsSelect the HOUSE CODE by pressing C/FSelect CHANNEL(1-4) by pressing C/F. This number will be confirmed upon pressing the SET button, or if no key is pressed for 10 seconds. If only one transmitter is available, it is recommended to leave the CHANNEL be "01”The range of House Codes are from "01" to "15". Make sure all transmittersin your system are set to the same House Code.Humidity & Temperature will displaySelect °C or °F of Temperature by pressing C/F and pressing SET. Once setup of remote transmitter is completed, it will start transmitting at one minute intervalsSTEP 1 : setting the remote transmitters* Use a different house code if your weather station detects other signals from neighboring sources* Factory default: house code = 01 and channel = 01STEP 2 : setting the receiver8234567112234SYNCHRONIZATIONAutomatic Learn Function:Manual-Learn Function (Searching for Remote Signals):The Learn function begins automatically and runs for 3 minutes when receiver batteries are first installed. Press and hold Channel for 3 seconds in clock display modeIf a new transmitter is added or if signal is lost (outdoor display blinking), the learn function must be executed again.Within these 3 minutes, the receiver will beep and displaythe temperature & humidity signals from transmitter(s).A beep sound indicates that learn function has startedThe Outside the symbol will flash and unit will beep as each remote sensor is detectedTemperature & humidity readings of the remote sensor will display on the receiver.If the signals are not received within this 3 minutes, the outside temperature and humidity will show " ". If this is the case, bring the units closer togther or try a different location. Then restart the auto learning function by temporarily removing the batteries from receiver.*Moon Phase DisplayMOON PHASEThe moon phase is automatically updated according to the year/month/day. New MoonYoung CrescentFirst QuarterWaxing GibbousFull MoonWaning GibbousLast QuarterOld Crescent12876543WT440H Transmitter1OWNERS MANUALSET C/ F-AA 1.5V+-AA 1.5V +110SET C/F-AA 1.5 V+-AA 1.5 V +SET C/F-AA 1.5V+-AA 1.5V +TEMPERATURE / PRESSURE HISTORICAL BAR GRAPH Note: If you have multiple transmitterspress CHANNEL to scroll through below sequence:The bar graph lets you see the pressure trend over a period of 24 hours. (automatically resets at midnight). The bar graph will show the Pressure Trend (Default), or the Local or RemoteTemperature by pressing ON/OFF(C/F) in Clock1 mode. The sequence is: Pressure Trend Inside Temperature Trend Outside Temperature Trend ( , , ) Pressure TrendInside Temperature TrendOutside Temperature TrendChannel 1Channel 2Channel 3
BSPECIFICATIONSWeather Station Receiver WS928Battery Type: 2 X 1.5V AA batteriesTemp. Range: -20Temp. Range: -4 °C to +55°C°F to +131°FMeasurement Accuracy: +/- 1°C within measuring range of 0° to 40°CResolution: 0.1°CHumidity Range: 15% to 95% RHMeasurement Accuracy: +/- 5%Resolution: 1%TROUBLESHOOTINGP.9 P.10P.16P.12P.13 P.14 P.15P.11Check Remote Temperature & HumidityCheck Inside Temperature & Humidity°C or °F Temperature DisplayMin and Max Temperature & HumidityA*BCDTEMPERATURE & HUMIDITY DISPLAYAfter insert batteries, inside temperature and humidity readings will ing the the display alternately on the receiver.Toggle between °C and °F by pressing C/F in Clock2 mode.Press MIN in Clock1 mode to display minimumtemperature and humidityPress MAX in Clock1 mode to display maximum temperature and humidityNote:Min/Max temperature history readings are automatically cleared daily at 00:00The trend indicator shows the trend of inside/outside temperature, inside/ outside humidity and pressure determined by the particular sensor in the past half hour interval.Arrow IndicatorRising Steady FallingTrendTemperature, humidity & pressure trendPress ON/OFF key continuously to scroll and select the high temperature alarm ( ), low temperature alarm ( ) or disable (blank) the alarm functionPress + or - key to set the temperature limit valuePress MODE to finish The default value 14°C or the existing preset will flasha*2b5c34When temperature alarm soundsPress any key to stop temperature alarm; or If no key is pressed, the temperature alarm will automatically stopitself after one minute. The temperature alarm will sound again 5 minutes later.Once triggered, the temperature alarm comes on as a distinctive sound, different to that of Alarm1 and Alarm2. This alert indicates that the temperature has exceeded the preset temperature limit. The symbol will also flashRemote temperature alarm1 5Scroll to the remote channel temperature alarm mode by using MODE Press + or - key to set the temperature limit valuesPress CHANNEL to select a transmitter channel The default value 14°C or the existing preset will flash125634*Scroll to local temperature alarm mode by using MODE 1TEMPERATURE ALARMYou can set the high or low temperature alarms for the local reading and for one remote channelLocal temperature alarm This weather station is capable of detecting barometric pressure changes, and based on the data collected, can predict the weather for the next 12 to 24 hours. The effective range covers an area of 30 – 50km.Wind Alert* Wind Symbol will display if the pressure has greatly changed in the past 3 hours.Storm Alert* Storm symbol will flash to warn of a potential thunderstorm.About Snow Freeze Warning* Snow symbol will flash to warn of 'snowing'.* Activated when Outside channel (Channel 1) temperature is between -1.9 °C and +2.9 °C* Snow will appear solid if and when Outside channel (Channel 1) temperature falls below -1.9 °C: the point of moisture freezing.Note:* Transmitter Channel 1 will be used for snow indication and freeze warning. Animated weather forecast symbolsWEATHER FORECASTRainingFreeze Warning Storm AlertSnowingSunny CloudyOR ORWeather Station Transmitter WT440HBattery Type: 2 X 1.5V AA batteriesTemp. Range: -30Temp. Range: -22°C to +55°C°F to +131°FHumidity Range: 15% to 95%Transmission Frequency: 433.92 MHzTransmission Range: up to 40 meters in open areawww.upm-marketing.com*ACD43512453612Wind AlertCOMFORT LEVEL ICONThe comfort level will be shown based on the data collected from inside temperature / humidity. An indicator will display to show if the level is Comfortable, Normal or Uncomfortable.Comfort LevelPress Channel to toggle between outside channels :Outside (channel 1) Outside 2 (channel2) Outside 3 (channel3) Temperature and humidity readings will display on the receiver.Press ON/OFF key continuously to scroll and select the high temperature alarm ( ), low temperature alarm ( ); or to disable the alarm function wait for the ( ) blank display.Press MODE to finish<flash ing snow> flashing thun derstorm and rain toge ther< >DescriptionIt shows that the current environment is at the ideal range for the inside temperature and relative humidity It shows that the current environment is acceptable It shows that the current environment contains excessive or inadequate moisture;or is too hot or coldIf the outside temperature falls below -30°C or the outside relative humidity falls below 15%, the symbol "LO" will appear on the screen respectively; If the humidity rises above 95%, the symbol "HI" will appear on the screen. Both events are quite normal and do not mean that your weather station is defective.iiiiiiivWait for about 1-2 minutes to ensure the units are not in a phase change. Otherwise, re-synchronize receiver by holding Channel button for 3 seconds until a beep is heard.Ensure the remote sensor is out of direct sunlight, and away from other sources of heat.- Repeat the learn procedures. (see sychronization section)- Temperature may be below -30°C.- Batteries in transmitter may need changing. - Move the transmitter closer to the receiver.- Make sure transmitter is away from sources of electrical disturbance.Reset the unit (to default mode) by removing the batteries in both the receiver and transmitter(s). Then re-insert the batteries and re-enter your settings.The temperature measurement of transmitter and receiver do not match.Transmitter temperature readingsseem to high.Receiver is no longer receiving remote data or the displayis incorrect. Operation is not normal or certain functions do not perform Problem SolutionREMARKS:* After set up, allow 12-24 hours for the Weather Station to operate at a steady state as this will result in a more accurate forecast.* Common to weather forecasting, absolute accuracy cannot be guaranteed. * If the Weather Station is moved from a location to another location, which is significantly higher or lower than its initial standing point (e.g from the ground floor to 1st floor of a house), remove the batteries and reinsert them after about 30 seconds. Then re-synchronize with the transmitter with the receiver (see synchronization section) A change in location may affect the transmitter readings of heat and air pressure. Also readings may be inaccurate due to heat escaping from areas of your home with less insulation.WEATHER FORECASTLOW BATTERY INDICATIONIf the low battery symbol " " displays (in the Inside weather display area) then the receiver batteries are low. A low battery may affect the units performance, for example:- the LCD display appears faint;- the transmission range is reduced;- the data may not display from remote transmitter(s)RECEIVER:You will need 2 x AA batteries for the receiver.* Note: Changing the batteries in the reciever will cause all settings to be erased.TRANSMITTER:If the low battery symbol " " is displayed in LCD display of transmitter, then the remote transmitter batteries are low. The low battery symbol " " for the transmitter will also display on the reciever (in the Outside weather area)The transmitter takes 2 x AA batteriesIf a transmitter is exposed to very low or high temperatures for an extended period of time, the batteries may lose power, which may causereduced transmission range.31425*OUT11431OUTWARRANTYLimited 5-year WarrantyThis product carries a five (5) year repair warranty against defects in workmanship and materials. At their discretion, retailers may replace the unit within the stated warranty period, when returned with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.If the product is defective,(i) return it, with a dated proof of purchase, to the retailer from which you purchased it.FCC / Industry Canada COMPLIANCEThis device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.Operation is subject to the following two conditions:(1) this device my not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Navigation menu