Manitowoc Ice G 0600 Users Manual

J-0600 to the manual 0f415ec4-f908-43e6-aa2a-9e4e569e2fbf

: Manitowoc-Ice Manitowoc-Ice-G-0600-Users-Manual-553179 manitowoc-ice-g-0600-users-manual-553179 manitowoc-ice pdf

Open the PDF directly: View PDF .
Page Count: 3

Download
Open PDF In Browser	View PDF

J/B/G-0600 COMPRESSOR REPLACEMENT
Installation Instructions
NOTE:

THIS REPLACEMENT IS ONLY FOR THE J, B, AND G-SERIES ICE MACHINES. START AND RUN
COMPONENT CHANGES VARY WITH THE TYPE OF MACHINE. FOR J-SERIES MACHINES ONLY, THE
RUN CAPACITOR NEEDS TO BE REPLACED WITH THE ONE INCLUDED IN THE KIT. B AND G-SERIES
MACHINES NEED ALL OF THE START AND RUN COMPONENTS REPLACED WITH THE ONES
INCLUDED IN THE KIT.

1. Disconnect power to the ice machine at the electrical
disconnect (moving the toggle switch to the off
position will not disconnect line voltage).
2. Remove panels (top, front, left and right sides).
3. Recover refrigerant from ice machine.
4. Remove right side corner post (when facing the front
of the machine) and back panel.

6. Unsweat suction line at compressor port. Unsweat
discharge and process lines at the T fitting and
swage joint (or after “T” fitting, if remote)
respectively.
NOTE:

IF REPLACING COMPRESSOR IN A
REMOTE ICE MACHINE, BE SURE TO
UNSWEAT THE CONNECTION BETWEEN
THE HPR VALVE AND THE PROCESS
TUBING AT THE “T” FITTING.

Swage Joint

“T” Fitting

5. Remove wiring from compressor terminals.
7. Remove compressor from machine. Make sure to
crimp and braze shut ports to compressor.
8. Insert new compressor into the machine, as shown.

Manitowoc Ice, Inc.
2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA
Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879
Web Site - www.manitowocice.com

8006183
Sheet 1 of 3

06/25/01

9. Fit tubing provided into the proper place, as shown.
Cut ice machine suction line to fit new tubing.
Deburr suction line before fitting new tubing in.

11. Braze all tubing into place. Purge system with
nitrogen during all brazing operations on the ice
machine.
NOTE: IF REPLACING COMPRESSOR INTO A
REMOTE ICE MACHINE, MAKE SURE TO
FIRST FOLLOW INSTRUCTIONS A, B, AND C
BELOW,
BEFORE
PROCEEDING
TO
INSTRUCTION #10.

12. Use electrical tape to seal suction line insulation.

A. Replace elbow with “T” fitting.

13. Reattach the wiring harness to the compressor.

B. Replace HPR valve and L-shaped tube that was
removed earlier. Adjust to fit without rubbing
against any other parts of the machine.

14. Replace the filter/dryer before evacuating the
machine. Make sure that the filter/dryer tubing is
not rubbing against the compressor.
15. Evacuate machine to 500 microns.
C. Return to instruction #10.
10. Place armaflex insulation provided in kit on suction
line, as shown in picture below. Slide insulation up
tubing and secure while brazing.

8006183
Sheet 2 of 3
06/25/01

16. Charge the machine with the nameplate charge.

17. Make sure that all the tubing is not rubbing against
anything else in the machine.
18. Reinstall the corner post that was removed earlier
and place electrical cover on compressor.
19. Reinstall back panels of ice machine.

20. Make sure to replace start and run components
according to the machine you are replacing the
compressor in. See note in the beginning of
instructions for designation.
21. Reinstall all other panels.
22. Reconnect power and test run ice machine.

8006183
Sheet 3 of 3

06/25/01



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Sandy R. Scheer
Comments                        : 
Company                         : Manitowoc Ice, Inc.
Create Date                     : 2009:05:18 09:02:06-05:00
Modify Date                     : 2009:05:18 09:02:17-05:00
Source Modified                 : D:20010817205918
Subject                         : 
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2009:05:18 09:02:17-05:00
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Document ID                     : uuid:7f7b9d82-979e-4ef4-b875-f48817963618
Instance ID                     : uuid:37fe7879-2f78-40c7-b110-b859e3c13fda
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : Sandy R. Scheer
Producer                        : Adobe PDF Library 9.0
Keywords                        : 
Page Layout                     : OneColumn
Page Count                      : 3

EXIF Metadata provided by EXIF.tools