Manley Toys 34822-27 RC Robot User Manual

Download:
Mirror Download [FCC.gov]
Document ID	813788
Application ID	3onl71tClOyzUgjgwnUFCQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	64.59kB (807364 bits)
Date Submitted	2007-07-09 00:00:00
Date Available	2007-07-09 00:00:00
Creation Date	2007-07-05 16:29:15
Document Lastmod	2007-07-05 16:36:56
Document Title	User Manual

IM for i-Que personal robot
Introduction:
The i‘Que personal robot is the world’s most intelligent robot. It is designed to move
around your home, learn about you, and give you information on subjects such as
biographies, Word definitions, math, sports, and even animals. i-Que will learn about
you, your friends and family, even you pets and favorite TV shows and adjust his
programming to your needs. In short, i-Que will be your new best friend and mentor.
Installing the batteries:
i-Que runs on a 9.6 rechargeable battery pack. The first thing to do is to take the pack
and install it into the bottom of the inue robot. Open the battery door with a small
screwdriver, snap the battery clips together, place the battery pack in the compartment,
and reinstall the door and screw.
While on the bottom, check to see that the frequency switch is set to CH 04
Take i-Que’s communicator and open up the rear battery comparhnent. Install 3 AAA
batteries and replace the battery door The LCD screen should come on.
Check to see that the frequency switch is set to CH 0 (the same as the switch on the
bottom of the i-Que robot)
Place i~Que’s eommunicator in the back of the robot so that it can be easily found.
Battery Warnings: (Adults assembly required)
Battery charging must be done by ADULTS only.
Use alkaline battery recommended.
Do not use rechargeable battery.
Non-rechargeable battery is not to be recharged.
Only battery of the same or equivalent type as recommended is to be used.
Battery is to be inserted with the correct polarity.
Exhausted battery is to be removed from the toy.
The supply terminals are not to be short-circuited.
Please keep this information for future reference.
Remove battery from the product before extended storage.
Model No.34822
loflS
Setting up the charging base:
Find the charging base and the power adaptor Place the charging base near the
baseboard of the wall and within distance of the wall socket. Plug the power adaptor into
the port in the side of the charging base. You should see the LED called “POWER” light
up. This means that the base has power. If the LED is not lit, cheek to see that the wall
switch is set to ON to get electricity to the wall socket you have selected.
Charging i-Que:
Look under the base of the i~Que robot and find the ON/OFF switch. Turn the switch to
ON. Place i—Que directly on the charging base If the robot is properly positioned on the
charging base, the “CHARGE” LED will be lit. If it is not, try to move i-Que round on
the base until it the LED comes on.
Leave i~Que for about 8 to 10 hours to allow him to fully charge.
Master ON/OFF switch
i—Que is programmed to work 24 hours a day, seven days a week. If you want to tum him
off, use the Master On/Off switch on the bottom of the robot
Using the i-Que communicator:
The communicator transmits to inue by radio waves. It works best from a distance no
greater than about 10 feet.
To use the communicator, you must have BOTH i-Que and the communicator set to the
SAME FREQUENCY. There are two choice of frequencies in case that you should
have 2 i-Que’s in the same area. This way, each communicator can be tuned so that it
cannot accept entries of anotheri
Take the controller and type in the word “i»Que”. This will wake him up for the first
time.
i-Que will remove himself from the charging base, raise his head, and introduce himself
to you.
i~Que will show you some of his capabilities. He will also ask you some questions. The
answers to these questions will be permanently stored in i you can take control of his movements in
Drive mode.
60f15
Press the MENU button. Press the SPACE button until the words “Drive Mode” appear
in the LCD screen. Press the ENTER button to begin Drive mode.
In Drive mode, you control 1— Que’ s motors. You can make him move forward,
backward, or turn left and right Press and hold the “Y” button to move forward the “B”
button to move backward the “Q’ button to rotate Lefl, and the “P” button to rotate
Right.
Once i-Que is where you want him to be, press the Menu button to exit control of i—Que’s
motors.
Programming i-Que to make a speech:
You can program i-Que to make a speech that you compose. Use Speech Mode to do
this.
Press the MENU button. Press the SPACE button until the word “speech” comes on the
LCD screen. Press the ENTER button to go into Speech mode.
Type any thing that you want i-Que to say. It can be a speech up to about 100 words.
When you have finished your speech, press the ENTER button. i-Que will store you
Speech into his memory.
TIP: i—Que is programmed to check against objectionable words. If you try to use these
words, he will not allow this speech to be stored or replayed.
To hear i»Que say your speech, Press the MENU button to get to SPEECH mode. Press
the SPACE button until the words “play speech” appear on the LCD. Press the ENTER
button and i-Que will start to say your speech.
TIP: You can change i—Que’s voice for your speech. Go to the SET UP section of this
manual to find out how. Your speeches may be even more effective or funnier!
Using i-Que's phonebook:
i—Que can store phone numbers and contacts for you. Use PHONE BOOK mode.
Press MENU. Press the SPACE button until the words “ phone book” appear on the
LCD screen.
i-Que will ask you for the entry name and the phone number. Follow his directions to
enter names, phone numbers or to retrieve them.
7of15
Using Memo minder:
i-Que can be programmed to warn you about special events of occasions. Use Memo
Minder mode.
i-Que will tell you how to enter the time, date, and a name of the event, When the time
comes up, i-Que will let you know.
Customizing i—Que by using SET UP mode:
When you first used i-Que, he asked you for many pieces of information. These included
setting the clock and the date. But, there are many other things that you can enter or
customize i-Que to your liking. Use SET UP mode for this.
Press the MENU button until you see the words “SET UP" appear on the LCD screen.
Press the ENTER button to go into Set up mode.
Use the SPACE button to select the various modes: The go in the following order:
Voice Select (allows you to change i-Que’s voice)
Set Time (lets you set or adeSt his clock)
Set Date (lets you set the date)
Read Time (in using this, i-Que will tell you the time of day and date)
Set Birthday (use this to enter your birthday)
Alarm set (use this to set i-Que to wake you up)
Alarm on/off (this mode will let you turn the alarm on or off easily)
Quiet set (this mode lets you tell i—Que when not to bother you or move around)
Quiet on/off (this mode turns quiet time on and off)
TV time set (this mode lets you enter your favorite TV show times)
TV TM on/off (this mode turns the TV announce on or off)
VR on/off (this mode allows you to use Voice Recognition — NOTE: i-Que is preset with
voice recognition OFF until you get used to his programming. It is an advanced mode.)
Check status (this mode will let you check the status of various inputs of i-Que)
Reset (this mode is a way for you to CLEAR all inputs in the flash memory of i»Que.
WARNING. Use this ONLY if you want to clear all entries and begin i-Que as if he
were turned on for the first time).
Changing i-Que’s voice:
The words “voice select” will appear on the LCD screen.
You can change i-Que‘s voice anytime you want. Maybe one type of voice is easier for
you to undersmnd. Or maybe you just want something different. It’s your choice,
Press the MENU button and use the SPACE button to get to Set Up. Press ENTER to go
into Set Up mode. The words “voice select" will be on the LCD screen. Press ENTER to
go into Voice Select mode.
80f15
1- -Que will make a statement in a voice and ask you if you like this particular voice. If you
like the voice, press the YES Button If you don’ t, press the NO button and 1 Que will
give you another choice. When all choices are given,1'-Que will repeat them again from
the beginning.
As soon as you press the YES button, i-Que will return to his normal mode and use that
voice until you change him again,
Set time mode:
i-Que will ask you for the time and date when you first turn him on. But, it may be
necessary to reset this information, make adjustments, or re-enter it if his batteries
become completely discharged. Use SET TIME mode for this.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Set time” on fire LCD
display. Press the ENTER button to go into Set time mode.
The LCD screen will show four “symbols”. Enter the numbers that correspond to the
current time For example, 0812) for Eight Twelve. If you enter the wrong number, use
the BACKSPACE button to erase it (the backspace button 1s the button on the 2“‘1 row of
the far right that also is the “DEL”).
When all four numbers are shown on the screen, press the ENTER button.
The letters “AM” will appear on the screen. If the time is AM, press ENTER. If the time
is PM, press the SPACE button. Press ENTER when the proper setting is on the LCD
screen. The words “Finished" will appear briefly on the LCD screen.
Set Date:
Just like Setting time, it may be necessary to reset the date. Use Set Date mode for this.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Set date” on fire LCD
display. Press the ENTER button to go into Set date mode.
The words “enter mon " and two symbols will appear on the LCD screen. Enter the
month in digits (for example, January would be 01, December would be 12), Press
ENTER when the digits are correct. The words “enter date” and two symbols will
appear.
Enter the correct date. (for example, 05 for the fifth, 21 for the twenty-first). Press
ENTER when the digits are correct. The words “Enter Year" and four digits will appear.
90f15
Enter the year and press the ENTER button when correct. The words “finished" will
appear briefly on the LCD screen.
READ TIME;
Read time lets i-Que tell you the current time and date.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Read time” on the
LCD display. Press the ENTER button to go into READ TIME mode. i-Que will state
the time and date for you.
Set Birthday:
In the event that i-Que is reset, you may need to reset the birthday. Use Set Birthday for
this entry.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Set birthday” on the
LCD display. Press the ENTER button to go into Set birthday mode.
The words “enter month” and two symbols will appear on the LCD screen Enter the
month in digits (for example, January would be 01, December would be 12). Press
ENTER when the digits are correct. The words “enter date” and two symbols will
appear.
Enter the correct date. (for example, 05 for the fifth, 21 for the twenty-first). Press
ENTER when the digits are correct. The words “Enter Year” and four digits will appear.
Enter the year and press the ENTER button when correct. The words “finished” will
appear briefly on the LCD screen.
10 of 15
Alarm set:
This mode tells i-Que what time you would like him to wake you up,
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Alarm set” on the
LCD display Press the ENTER button to go into Alarm Set mode.
The LCD screen will show four “symbols". Enter the numbers that correspond to the
current time For example, 0812) for Eight ~ Twelve. If you enter the wrong number, use
the BACKSPACE button to erase it (the backspace button is the button 011 the 2nd row of
the far right that also is the “DEL”).
When all four numbers are shown on the screen, press the ENTER button.
The letters “AM” will appear on the screen. If the time is AM, press ENTER. If the time
is PM, press the SPACE button. Press ENTER when the proper setting is on the LCD
screen. The words “Finished” will appear briefly on the LCD screen.
NOTE: The ALARM IS NOT SET YET! YOU MUST TURN THE ALARM ON. Go
to the next step:
Alarm 0n/Off:
This allows you to easily turn i-Que’s alarm function on or off.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Alarm On/Oft" on the
LCD display. Press the ENTER button to go into Alarm On/Off mode. You will see the
word “ON”. Press ENTER to turn the alarm on. Use the SPACE button to select OFF
and press ENTER if you want the alarm to not go off.
TIP: You can check to see if the alarm in i-Que is set but pressing the CHECK STATUS
button located just to the left of i-Que’s cartridge slot. i-Que will give you his status and
let you know if the alarm is set or not.
Quiet time:
This mode tells i—Que when he should not disturb you. For example, you probably don’t
want him rooming around your house all night. So, you can tell him to be still from 10
PM until some time in the morning. This way, he won’t disturb you.
NOTE: i-Que has been preset to be quiet from 10 PM to 7 AM in the factory. You can
use Quiet time to adjust this to your liking. In addition, if you use the communicator, i-
Que will ignore Quiet time automatically and return to it after some time of inactivity by
you.
lloflS
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Moder Use the SPACE button until you see the words “Quiet set” on the
LCD display. Press the ENTER button to go into Quiet Set mode.
The LCD screen will show four “symbols”. Enter the numbers that correspond to the
time you want i~Que to START his period ofinactivity. For example, 0812) for Eight -
Twelve. If you enter the wrong number, use the BACKSPACE button to erase it (the
backspace button is the button on the 2“d row of the far right that also is the “DEL’fil
When all four numbers are shown on the screen, press the ENTER button.
The letters “AM” will appear on the screen If the time is AM, press ENTER. If the time
is PM, press the SPACE button. Press ENTER when the proper setting is on the LCD
screen.
The words “Quiet End” will next appear on the screen. This refers to the time that you
want i~Que to start to be active again Enter the time and AM or PM exactly as the first
entry. The word “finished” will appear briefly on the LCD screen.
NOTE: The default setting for Quiet time is ON. So, if you want you i-Que to ignore
quiet time, you must set it to OFF in the next mode:
Quiet Oil/Off:
This mode allows you to ignore any setting for Quiet time. If you turn quiet time off, i—
Que will continue to wander and move around 24 hours a day.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Quiet On/Oft” on the
LCD display. Press the ENTER button to go into Quiet On/Otfmode. You will see the
word “ON”. Press ENTER to turn Quiet time on Use the SPACE button to select OFF
and press ENTER if you want no Quiet time for your i-Que.
TV time:
TV time allows you to tell i~Que when you want him to remind you of your favorite TV
shows. Enter this mode and i-Que will tell you how to make the entries
TV Time Off.
TV time off will tell i~Que that you don’t want to be bothered with this information.
Press the MENU button. Use the SPACE button to get to Set Up‘ Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “TV TM Orr/Off” on
the LCD display. Press the ENTER button to go into TV time On/Off mode. You will
12 of 15
see the word “ON”. Press ENTER to turn TV Time on. Use the SPACE button to select
OFF and press ENTER if you want your i-Que to ignore your TV time entries.
Voice Recognition ON/OFF (advanced mode)
VR ON/OFF enables or disables i-Que’s Voice Recognition. i-Que is preset at the
factory with this mode OFF. It is advised that you understand i-Que’s functions well
before trying this advanced mode.
i~Que has the ability to recognize almost anyone’s voice. It can recognize four words.
1) i-Que (used to call him or wake him up)
2) Yes
3) No
4) Repeat (used in the same way the repeat button on the communicator works)
To turn the Voice Recognition ON, Press the MENU button. Use the SPACE button to
get to Set Up. Press ENTER to go into Set up Mode. Use the SPACE button until you
see the words “VR On/Ofi” on the LCD display. Press the ENTER button to go into
Voice Recognition On/Off mode. You will see the word “ON”. Press ENTER to turn
Voice Recognition on. Use the SPACE button to select OFF and press ENTER if you
want not to use Voice Recognition for your i-Que.
HOW TO USE VOICE RECOGNITION:
If you use voice recognition, remember to stand within about 3 feet of your i-Que.
Speak clearly. If you say “i-Que”, he should wake up or give you a response. If he asks
you a question, you can respond with a “yes” or “no” answer without using the
communicator. And, if you didn’t hear what he said, say “repeat" after he stops talking
and he will say the last statement again.
SPECIAL NOTES about Voice Recognition:
i—Que will ONLY listen to Voice recognition when he is not talking or not moving. The
reason is that the noise he generates will distort you voice into his microphones.
Although i-Que is programmed to understand almost all kinds of voices, it may be that
your particular voice or accent is not reliable to him. In this case, do not use Voice
Recognition mode and rely solely on the communicator for direct communication with
your robot,
13 oflS
CHECK STATUS:
Check Status tells i-Que to give you a report on various entries in his memory. He will
tell you the time, the date, if the alarm is set or not, eto‘
Press the MENU button. Use the SPACE button to get to Set Up, Press ENTER to go
into Set up Mode. Use the SPACE button until you see the words “Check Status” on the
LCD display. Press the ENTER button to go into Check Status mode. You will see the
word “Check Status". i-Que will tell you the status of himself.
RESET:
WARNING: Using RESET will set i‘Que back to all of his factory settings. All of the
infonnation you have entered or he has learned will be erased. i-Que will become as he
was when you first turned him on.
Press the MENU button. Use the SPACE button to get to Set Up. Press ENTER to go
into Setup Mode. Use the SPACE button until you see the words “RESET” on the LCD
display. Press the ENTER button to go into Reset mode. i-Que will walk you through the
steps on how to complete Reset mode.
USING I QUE ON A TABLE TOP:
i—Que is designed to work on a surfaces other than the floor. He can be placed on a table
top. i-Que has sensors in his chassis that wams him to not fall off the table.
I Que’s collision avoidance sensors.
inue has sensor in his front that allow him to detect object in front of him If he should
find a object in his path, he will attempt move around it our out of a comer.
i—Que’s head height sensor:
i-Que was programmed to roam around his environment If he finds an object that may be
blocked because his head is elevated, i‘Que will automatically lower his head and attempt
to travel under it.
14 of15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
0 Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC ID: NS634822-27
TOYQUEST
LOS ANGELES, CA 90064
www.tquuest.com
Model No‘34822
150f15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2007:07:05 16:29:15Z
Modify Date                     : 2007:07:05 16:36:56+08:00
Metadata Date                   : 2007:07:05 16:36:56+08:00
Format                          : application/pdf
Document ID                     : uuid:da92e87e-3d00-4ab5-b286-322dbabb4212
Instance ID                     : uuid:4a8da849-42fa-42f8-9dd2-c0da18472469
Page Count                      : 15

EXIF Metadata provided by EXIF.tools