Pdf Dss3C Installation Manual DS3 Series Door StationManualREVB User

Pdf Dsf3Bz Installation-Manual pdf_DSF3BZ_installation-manual pdf_DSF3BZ_installation-manual DSF3BZ products

Pdf Dsf3C Installation-Manual pdf_DSF3C_installation-manual pdf_DSF3C_installation-manual DSF3C products

Pdf Dss3Bz Installation-Manual pdf_DSS3BZ_installation-manual pdf_DSS3BZ_installation-manual DSS3BZ products corebrands-resources

User Manual: Manual Pdf Dss3C Installation-Manual pdf_DSS3C_installation-manual DSS3C products

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

Specifications

Introduction

Introduction

DS3 Series Door Station
Installation Manual
DSS3/DSC3/DSF3
Getting Help
You can get support via the Internet at
www.elanhomesystems.com, or call
Tech Support at (800) 622-3526

Specifications

ELAN’s new DS3 Series Door Station and the COM2
Communications Controller provide you with full twoway communications and door latch control from your
touch-tone telephones. A simple #-D (for Door) from any
touch-tone phone allows you to speak with visitors at the
door. Another simple button press (“0”) activates the
door latch to let them in. The door latch must be installed
and is not included. The DSC3, with its on-board color
camera, gives you the option of seeing who's there
before you even pick up the phone. The door stations
must be utilized with ELAN’s COM2 Communications
Controller.

Door Station Speaker

8 ohm, sealed back mylar cone

Microphone

Hi-gain omni-directional condenser

Door Latch Relay

12VDC coil, 2A contact rating

Wiring Requirements

Cat-5, 1000 ft. max

Dimensions (H/W/D)

5 3/8" X 3 7/8" X 3/8" (1" D for DSS3)

Door Station Models

DSC3 Color Camera Specifications

ELAN’s two-wire door station models include the DSS3
Surface Mount Door Station, the DSF3 Flush Mount Door
Station, and DSC3 Flush Mount Door Station with Color
Camera. Designed to be installed in a variety of locations,
each door station allows custom installation in areas
such as the front door, back door, guest house, or gates.
Each model allows independent conversation with visitors at up to four locations. With the Door Latch Activation feature, you can remotely unlock a door or gate and
let the visitor enter, if desired (a third-party door latch
must be installed and is not included with ELAN door
stations)

Imager

NOTE: The new DS3 Series Door Stations are only
compatible with ELAN’s COM2 Communications
Controller and will not work with the Z•600
Communications Contoller or HDC1050/HDC2050
Telephone Interface Cards used with ELAN HD systems.

© ELAN Home Systems 2006 • All rights reserved.
Part Number 9900826 Rev A

PreWiring

Item

Description

1/3 in. CCD

Auto Iris

1/50-1/100,000 sec.

Lux

.05 min.

Resolution

480 TV lines

Horiz. Viewing Angle

120°

Vert. Viewing Angle

100°

Swivel

+15°/-15° left to right

Video Output

1V peak-to-peak

Video Output Impedance

75 Ohms

Power Requirements

12VDC @ 130 mA (included)

Video Balun Connections

Setting DIP Switches

VBRM Video Balun

PreWiring
The DSF3 and DSS3 Door Stations require two conductors to achieve full functionality. The DSC3
requires six conductors in order to utilize the camera
functionality (eight for long runs over 500 feet). Cat-5
network cable is recommended in each instance.
Route Cat-5 from the head-end location to each Door
Station location.
To mount DSF3 and DSC3 Door Stations, use an
ELAN DBK1000 Rough-In Bracket during construction. The DSS3 Door Station is designed to be surface
mounted and utilizes four wall anchors and screws,
(included).
For best aesthetics and audio quality, (and viewing
angle when positioning the DSC3), mount the unit
approximately 4-1/2 to 5-1/2 feet from the ground. It
is strongly recommended to test the view from the
camera before finalizing installation!

DS1

DS2

DS3

ON

ON

ON

ON

1 2
1 2

3

1 2

3

1 2

The DSC3 Door Station with color camera requires a video balance/
unbalance (balun) to properly pass video thru Cat-5 network cable at
any significant distances. Figure 3 shows the wiring connections using
Cat-5 network cable and the VBRM Video Balun (included).

DS4
3

3
VIDEO
OUTPUT

Door
Station

DIP Switch Setting

1

1 - ON, 2 - ON, 3 - ON

2

1 - OFF, 2 - ON, 3 - ON

3

1 - ON, 2 - OFF, 3 - ON

PWR3 PS INPUT
JACK
(12VDC 1.5 Amp)

QUICK LOCK
CONNECTOR

VBRM VIDEO BALUN

DSDS+
PWR
GND
VIDVID+
DSDS+

Quick Lock connection
used for runs up to
1000 feet.

Figure 1: Door Station DIP Switch Settings

NOTE: See the back page of this instruction for door
station pinouts.
+ +

CONNECTED
TO DSC3
DOOR STATION

1 2

3

RJ45
CONNECTOR
8
7
6
5
4
3
2
1

1 2

3

DSDS+
PWR
GND
VIDVID+
DSDS+

WARNING: The COM2 must be powered down during
DIP switch adjustments to ensure proper operation
and implementation of the new switch settings..

+DB- -DS+ 1RL2

Each door station has DIP switches that must be set
to allow the COM2 to differentiate between door
stations, and assign unique door chimes (see Figure
1). Locate and adjust the DIP switches to indicate the
desired door station for your location (see Figure 2),
i.e., front door = Door Station 1, back door = Door
Station 2 etc. (see Figure 2).

OUT
TO COM2

NOTE: Installer can use either the
Quick Lock Connector for runs from
0-1000 feet, or the RJ45 Connector
for runs from 0-500 feet to connect
the DSC3 with camera, but not both.

RJ45 connection
used for runs up to
500 feet.

DIP Switch Settings

1
2
3
4
5
6
7
8

DIP
SWITCHES

DSC3

-DS+

1RL2

CONNECTED TO
DSC3 DOOR STATION

Figure 3: VBRM Video Balun

DSF3 OR DSS3

Figure 2: DIP Switch Locations

Non Balun Application

DSF3 or DSC3 Installation

Non VBRM Applications

DSF3 & DSC3 Installation

In the rare instance that an ELAN VBRM Video Balun is not
used, the installer can still connect the DSC3 Door Station
and camera using Cat-5 for the door station, RG59/RG6
for the camera and 18/2 AWG stranded wire for power.
ELAN recommends using Cat-5 wire for the DS+ and DSconnections from the door station to the COM2 Door
Station Bus.
To connect the camera:
1. Unplug the power connector and RCA video connector
from the video balun on the DSC3 circuit board.
2. Remove the camera power connector, then strip back
the insulation on the red and black camera power
wires and connect the corresponding red and black
conductors of the 18/2 AWG wire as shown in Figure 4.

Both the DSF3 and DSC3 Door Stations are installed using the
DBK1000 Door Station/Camera Rough-In Bracket (sold separately).
In order to install the DSC3 or DSF3 Door Station in the DBK1000
the door station trim brackets must be mounted to the front of the
DBK1000, (see Figure 5). Note the orientation of the trim bracket’s
inner flanges.

4. Once the camera has been repositioned, tighten the
bracket screw to secure the camera at the desired
position.

Camera
Module

Camera
Module

+DB- -DS+ 1RL2

1 2

3
+ -

+

3

-

+ -

-

1 2

+

+DB- -DS+ 1RL2

Screw

Camera
Bracket

NOTE: DO NOT remove the DSC3's yellow (video) RCA
jack connector!

3. Remove the connector from the PWR3 Power Supply.
Figure 4.
4. Tie the red wire of the 18/2 AWG to the black/white
wire of the PWR3. Tie the black wire of the 18/2 AWG
to the black wire of PWR3 Power Supply (see Figure 4.)
5. Splice camera power to PWR3 using 18/2 wire.
6. Connect “F-to-RCA” barrel connector (included)
between the RG-6 or RG-59 coax cable and the DSC3
RCA composite video connector (yellow).
(Splice)

3

+

2

+ -

1

-

18/2
(for Power)
PWR3
POWER
SUPPLY
+DB- -DS+ 1RL2

To ELAN V883, S12,
or MOD4000 Video Controller

Normally located
at the equipment
head end.

Figure 4: DSC3 Without VBRM

Camera
Wire
DBK 1000
DOOR STATION
ROUGH-IN BRACKET

TRIM BRACKETS

Figure 5: DSC3 or DSF3 Trim Brackets

The DSC3 ships ready for horizontal installation. Should you
choose to mount the DSC3 vertically, the DBK1000 must also be
mounted vertically and the camera module must be rotated 90
degrees to orientate the camera display (see Figure 6.
Whether mounted horizontally or vertically, the camera wire
should always protrude from the UPPER-RIGHT corner of the
camera module when the DSC3 is viewed from the rear (see
Figure 6). To rotate the camera:
1. Use a 7/16 wrench to loosen the Screw and rotate the camera.
2. Make sure the Camera Wire is located in the upper right
corner of the camera module when the DSC3 is viewed from
the rear.
3. Adjust the viewing angle by carefully twisting the Camera
Bracket.

Figure 6: Camera Orientation
NOTE: Regardless of the DSC3’s orientation, always
make sure the wire protruding from the rear of the
camera module is located in the UPPER-RIGHT corner
when viewed from the rear.

DSC3 Doorbell Button

DSS3 Door Station Installation

The DSC3 Door Station is designed with a separate matching
doorbell button from the door station assembly. This enables
the button to be installed in a conventional doorbell location,
and the door station mounted higher up for optimum camera
viewing.

Orange
Brown
Black
Red
White
Green
COLOR
DOOR
NEW
CCTV
DSC2000
STATION
CAMERA /

To Video Balun
via Cat-5
To Door
Latch

{
{

For best viewing angle when positioning the DSC3, mount
the unit approximately 4-1/2 to 5-1/2 feet from the ground.
ELAN strongly recommends testing the view from the camera before finalizing installation.
Additionally, ELAN provides a matching doorbell button with
each DSC3 Door Station. Please be advised that all ELAN
DSC3 Door Station pre-wires should be wired for remote
placement of the doorbell button.
NOTE: Be sure to pull the doorbell push button wires through
the back of the DBK1000 Doorstation Rough-in Box.
NOTE: If the doorbell push button does not light after
connecting the db+ and db- leads from the door station,
reverse the leads, proper polarity must be maintained in
order for the doorbell light to function properly.

+DB- -DS+ 1RL2

NOTE: ELAN recommends using the provided doorbell only.
A non ELAN doorbell button has not been tested and is not
covered under ELAN’s Door Station Warranty.

DSC3
Door Station/
Color CCTV

3. Connect DS+ and DS- using a butt splice or some
other appropriate connector.
4. Mount the door station to the surface bracket, as
illustrated in Figure 8. Note the orientation of the
Mounting Plate flanges.

To Video Balun
via Cat-5

DSC3 Doorbell Button Installation

Recommended
Mounting Height:
4.5ft. to 5.5 ft.
-

Doorbell
Button

+

Figure 7: Recommended Camera Height

DSS3 Door Station Installation
The DSS3 Door Station is a surface mount door station
designed to work with the COM2, ELAN's next-generation inhome communications controller. Connect the DSS3 Door
Station using Cat-5 network cable as shown in the
COM2-To-Door Stations Wiring Diagrams below.
The DSS3 has a surface mounting plate that attaches to most
surfaces with 4 wall anchors and 4 screws (included). Attach
the door station and surface bracket as shown in Figure 8.

Figure 8: DSS3 Mounting Plate

To install the DSS3 Door Station:
1. Using the surface bracket as a template, mark and drill the
four corner holes. Insert a wall anchor in to each hole
2. Attach the surface bracket using the four surface mounting
screws.
NOTE: Make sure to make your electrical connections prior to
mounting the door station.

COM2 To Door Stations Wiring Diagrams
VID PWR

DSF3 or DSS3
DOOR STATION

DSC3 DOOR STATION

To
Door
To
Latch Doorbell

Cat-5
PWR
GRD
PWR
GRD
VIDVID+
DS DS+

-DS+ 1RL2

Black
Red
White
Green

*White/Brown
*Brown
*White/Green
*Green
White/Orange
Orange
White/Blue
Blue

DS+
Blue
White/Blue DS Orange
White/Orange
Green
White/Green
Brown
White/Brown

DS -

Door Station
Bus

Blue
White/Blue
Orange
White/Orange
Green
White/Green
Brown
White/Brown

COM2

DSF3 or DSS3
Option

Door Station
Bus

Blue
White/Blue
Orange
White/Orange
Green
White/Green
Brown
White/Brown

Cat-5

Cat-5

Blue
White/Blue
Orange
White/Orange
Green
White/Green
Brown
White/Brown

Snap lock
connector
DS+

RJ-45

Use for run from
0 to 500 feet max.

Butt Splice

External 12VDC
Power
Video

Power

VBRM Video Balun
To Video
Switcher

COM2

Door Station
Bus

* Splice White/Green with White /Brown
VID + and Green with Brown VID - for
camera runs between 500 &1000 feet.

Cat-5
Blue
White/Blue
Orange
White/Orange
Green
White/Green
Brown
White/Brown
+

+

COM2

White
Green

-

DSC3
Option 2

Use for run from
0 to 1000 feet max.

White/Brown
Brown
White/Green
Green
White/Orange
Orange
White/Blue
Blue
Blue
DS+
White/Blue
DS Orange
White/Orange
Green
White/Green
Brown
White/Brown

Video

Snap Lock
Connector

External
12VDC
Power

Orange
Brown

-

-

-

+

To
Video
Switcher

Butt Splice

VID PWR

DSC3 DOOR STATION

Butt Splice

To
Door
To
Latch Doorbell

Cat-5
PWR
GRD
PWR
GRD
VIDVID+
DS DS+

White
Green

+

Power

Orange
Brown

Black
Red

+DB- -DS+ 1RL2

VBRM Video Balun

Black
Red

BALUN

Purple
Blue
Gray
Yellow

+

Purple
Blue
Gray
Yellow

+DB- -DS+ 1RL2

-

-

DSC3
Option 1

*White/Brown
*Brown
*White/Green
*Green
White/Orange
Orange
White/Blue
Blue

BALUN

+

*White/Brown
*Brown
*White/Green
*Green
White/Orange
Orange
White/Blue
Blue

Limited Warranty
ELAN HOME SYSTEMS L.L.C. (“ELAN”) warrants the DSS3/DSF3/DSC3 Door Stations to be free from defects in materials and workmanship for the period of two
years (2 years) from date of purchase. The CCTV Color Camera in the DSC3 Door Station is warranted to be free from defects in materials and workmanship for
the period of one year (1 year) from date of purchase. If within the applicable warranty period above purchaser discovers that such item/s was not as warranted
above and promptly notifies ELAN in writing, ELAN shall repair or replace the item at the company's option. This warranty shall not apply (a) to equipment not
manufactured by ELAN, (b) to equipment which shall have been installed by other than an ELAN authorized installer, (c) to installed equipment which is not
installed to ELAN's specifications, (d) to equipment which shall have been repaired or altered by others than ELAN, (e) to equipment which shall have been subjected to negligence, accident, or damage by circumstances beyond ELAN's control, including, but not limited to, lightning, flood, electrical surge, tornado,
earthquake, or other catastrophic events beyond ELAN's control, or to improper operation, maintenance or storage, or to other than normal use of service. With
respect to equipment sold by, but not manufactured by ELAN, the warranty obligations of ELAN shall in all respects conform to the warranty actually extended to
ELAN by its supplier. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be
incurred in connection with repair or replacement.
Except as may be expressly provided and authorized in writing by ELAN, ELAN shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured by ELAN or services rendered by ELAN.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE, INCLUDING BUT NOT
LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CONSUMERS
To ensure that consumers obtain quality pre-sale and after-sale support and service, ELAN Home Systems products are sold exclusively through authorized dealers. ELAN products
are not sold online. The warranties on ELAN products are NOT VALID if the products have been purchased from an unauthorized dealer or an online E-tailer. To determine if your
ELAN reseller is authorized, please contact ELAN Home Systems at (859) 269-7760.

P/N 9900826 REV:B