Pdf LX XAP 1440 Quick Install Guide
2018-07-20
: Manual Pdf Lx-Xap-1440 Quick Install Guide pdf_LX-XAP-1440_Quick_Install_Guide LX-XAP-1440 products
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Fold Technical Support 801-822-5450 support@luxul.com READ ME FIRST Sales 801-822-5450 sales@luxul.com Fold READ ME FIRST - CONTROLLER COMPATIBILITY QUICK INSTALL GUIDE This XAP-1440 is compatible with the Luxul Wireless Controller for fast, easy configuration and deployment of wireless networks with multiple APs. 2. Thread the Ethernet cable through the cable gland assembly as shown, connect it to the Ethernet connector, secure the cable gland to the threaded recess on the access point, then tighten the cable gland nut to secure and seal the cable gland. nn Note: If you’ll be using this AP with a Wireless Controller, refer to the Quick Install Guide included with the Wireless Controller for setup instructions. AP SETUP AND CONFIGURATION 1 Physical Installation The XAP-1440 access point is designed for simple and efficient installation. However, due to the inherent complexity of outdoor installation, installation should be be performed only by experienced professionals. AC1200 Dual-Band Outdoor Wireless Access Point XAP-1440 Copyright and Trademark Notices No part of this document may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product. © Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and registered trademarks are property of their respective holders. LUX-QIG-XAP-1440-v1 05121709 Fold Includes: XAP-1440 Wireless Access Point PoE Injector and Power Cord Mounting Bracket and Hardware Ethernet Cable Because the signal generated by the XAP-1440 is directional, the unit should be located at the perimeter of the desired coverage area, with the large flat surface aimed toward the center. Mounting the Access Point Mounting the access point is a simple process outlined in the following steps. 1. Refer to the included Mounting Guide leaflet to assemble the mount and secure the AP to a pole or wall mount. Cable gland exploded view 3. Adjust the access point for best performance. The vertical elevation angle can be adjusted with the four hex screws on the mount, while the horizontal angle can be adjusted by loosening the clamp and rotating the assembly on the pipe. cc CAUTION: To comply with RF regulations, the AP should be adjusted from 0 to -20 degrees (horizontal to downward-facing). ww Warning: Do not locate the access point where it can come into contact with overhead power lines or other electric circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. nn Note: For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.: NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 280. Fold Fold Fold AP SETUP AND CONFIGURATION CONT. 2 3 Connecting Ethernet and Power Preparing for Access 4 Access and Setup IP Addressing Getting Connected The XAP-1440 is PoE ready and supports 802.3at PoE. A PoE injector is included with the device. To apply power, simply connect the end of the Ethernet cable to which the access point is connected to the provided PoE injector or other PoE switch. An Ethernet cable length of up to 300 feet can be used. If the XAP-1440 is connected to a network with a 192.168.0.X address scheme, and your computer shares a similar address on the same network, you can skip to the next step, Access and Setup. XX Connecting Via an Ethernet Device: Use Ethernet cable to connect your computer to the PoE switch or PoE injector to which the XAP-1440 is connected. Ethernet is the preferred method of connection. XX Connecting Via a Wireless Device: Connect your client device to the XAP-1440 default wireless network named Luxul_XAP-1440. The wireless network will run in Open Security mode, so no passphrase is required until Wireless Security is configured. nn Note: Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP) cabling. To ensure best performance and stable data transmission at 1000 Mbps, use Category-6 unshielded twisted pair (CAT6 UTP). PoE Injector Setup If your network uses an address scheme other than 192.168.0.X, you’ll need to set a temporary static IP address on the computer you’re using for configuration. To do so, set the IP address of your computer to an address in the 192.168.0.X range. Once you’re finished configuring the AP, you can return your computer’s IP configuration to normal, typically “Obtain Automatically/DHCP.” XX Data In: Connect an Ethernet cable from your router or switch to the Data In port of the included PoE Injector XX Data & PWR Out: Connect an Ethernet cable from the Data & PWR Out port of the included PoE Injector to the PoE Port of the XAP-1440 nn Note: Visit http://luxul.com/ip-addressing to learn more about changing your computer’s IP address and getting connected. XX AC Power: Connect the included AC Cord to the Power Input of the Included Injector first and then to the AC outlet. nn Note: The XAP-1440 is not a router and will need to be connected to a network with a router in order to deliver Internet access. Luxul AP From your Router or Switch OUT IN POE Injector PoE injector Power Source Hardware Operation LED Indicators Ethernet and Power nn Note: If another device on your network shares the 192.168.0.10 address, you’ll need to temporarily reassign or remove that device while you configure the XAP-1440. 5 Logging In To access the AP’s web configuration, open your web browser and enter the AP’s default 192.168.0.10 IP address in the address field. Log in to the AP using the default user name and password: Default IP: 192.168.0.10 Username: admin Password: admin Once logged in, use Quick Setup and follow the online help to configure the access point as desired. The LED indicators are located on the bottom portion of the enclosure, near the cable gland. PWR: If the green Power LED is On, the XAP-1440 is powered. If the Power LED is Off, the XAP-1440 is not receiving power. The Power LED blinks when the XAP-1440 is booting. WLAN: If the blue LED is On, the wireless radio is active and wireless access is enabled. Off indicates the wireless radio is not active and wireless access is disabled. PoE Injector: If the Green ON LED is illuminated, power is connected to the injector. If the ON LED is not lit, the injector is not receiving power. Reset Button: The Reset button is located inside the cable gland opening of the XAP-1440 and is used to restore factory default settings. To Restore Default Settings, with the XAP-1440 powered on, press and hold the Reset button for approximately 10 seconds, then release. cc CAUTION: Holding the Reset button for more than a few seconds will restore the AP to factory default and remove any custom configuration.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01 Create Date : 2017:05:12 09:43:42-06:00 Metadata Date : 2017:05:12 09:43:48-06:00 Modify Date : 2017:05:12 09:43:48-06:00 Creator Tool : Adobe InDesign CC 2017 (Macintosh) Instance ID : uuid:b7f80f7b-4914-e54b-ae57-084c7ecf065c Original Document ID : xmp.did:f0edc94a-00b7-40ae-81f2-7908dc521841 Document ID : xmp.id:29bee6c4-4d62-48f8-a1dd-63bfd9169dcd Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:b1bed71f-0b93-4b78-a1b7-39136810b0b5 Derived From Document ID : xmp.did:589ef922-dfbb-46f4-bd69-af42b53d5f36 Derived From Original Document ID: xmp.did:f0edc94a-00b7-40ae-81f2-7908dc521841 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Macintosh) History Changed : / History When : 2017:05:12 09:43:42-06:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Slug Family : Agenda Slug Version : 1.000 Slug Outline File Size : 0 Slug Kerning Checksum : 0 Slug Foundry : The Font Bureau Slug Font Kind : OpenType - PS Slug Checksum : 1084419514 Slug Post Script Name : Agenda-Light Slug Font Sense 12 Checksum : 1084419514 Page Count : 2 Creator : Adobe InDesign CC 2017 (Macintosh)EXIF Metadata provided by EXIF.tools