Marantec America D211315 Remote Control Transmitter User Manual Transmiters Inst w logo

Marantec America Corporation Remote Control Transmitter Transmiters Inst w logo

Users Manual

Instructions for Models: ML-143(1,2,4), ML-243(1,2,4), ML-343(1)ML-140(1,2,4), ML-240(1,2,4), ML-139(1,2,4), ML-239(1,2,4)TransmittersFEATURESA family of state-of-the-art transmitters is tailored for discerninghomeowner’s. Each transmitter is custom encoded and ergonomi-cally designed to be an integral part of your garage door openersystem. Offering 3 styles to suit your personal preference: theMidi (1-, 2- or 4-channel), the Mini (1-, 2- or 4-channel), and theMicro (1-channel), the smallest transmitter of its kind.1. Installing the BatteryMidi (Figure 1.A) and Mini (Figure 1.B)■Remove battery compartment cover (back of transmitter) byusing small screwdriver.■Insert the provided 12V battery (type 23A) as shown.■Replace battery compartment cover.Micro (Figure 1.C)Micro transmitters come with batteries already installed. Whenreplacing batteries follow the steps below:■Remove battery compartment cover (front of transmitter).■Insert two 3V batteries (type CR1025) as shown.■Replace battery compartment cover.Note: Replace batteries with same type only.2. Using the Transmitter■To open or close garage door, press and hold button (Midi andMini transmitters have indicator lights that will start blinking).When garage door begins to move, release button.■To stop garage door during travel, press and hold button untildoor stops, then release button.■To continue garage door travel after stopping it, press and holdbutton. Once pressed, the door will travel in the opposite direction.3. Transmitter MountingThe transmitters can be conveniently mounted inside your carusing the mounting plate, or the mounting plate and visor clip(Midi and Mini Transmitters only).Mounting Plate (Figure 2.)The mounting plate enables you to mount the transmitter easilyto the dashboard or other convenient area.■Secure the mounting plate to area of preference using velcro(not provided) or other means.■Snap the transmitter into the mounting plate, which will hold itfirmly in place.Visor Clip (Midi and Mini Transmitters: Figure 2.)The visor clip permits easy mounting of the transmitter to a visor.■Attach visor clip to mounting plate.■Snap transmitter into mounting plate.■Affix complete assembly to visor.ProgrammingCable3-hole TerminalProgrammingCable3-hole TerminalB. Micro TransmitterA. Midi or Mini TransmitterFigure 2. Mounting Plates & Visor ClipsC. MicroTransmitterB. MiniTransmitterA. MidiTransmitterFigure 1. Battery CompartmentBatteryCompartmentCover3V (type CR1025)BatteryProgrammingCable3-holeTerminalMicro TransmitterMicro Mounting PlateTransmitter—MidiMounting PlateVisor ClipMiniTransmitterBatteryCompartmentCover12V (type 23A)BatteryBatteryCompartmentCover12V (type 23A)Battery
4. Multiple TransmittersEach transmitter comes factory programmed with random codes.1-channel transmitters have one random code, 2-channel trans-mitters have 2 different random codes, one per button, and 4-channel transmitters have 4 different random codes, one per but-ton. Transmitters that accompany a power head have at leastone code that already matches that power head. Transmittersthat are purchased separately as accessories have random codesthat must be changed in order to match the code of the “active”transmitter you are already using. Below are instructions fortransferring an active code from a button on one transmitter toa button of your choice on another transmitter.■Remove battery compartment covers (as shown previously inFigure 1) of both transmitters, the one with the active codeand the new transmitter that needs to receive the active code.■Connect programming cable to both transmitters. Line upeither end of the stripped cable so 3 wires align with 3-holeterminal, then firmly insert cable. See Figure 3.■Press and hold button on transmitter with the active code ((L)in Figure 3). Midi and Mini transmitters have indicator lightsthat will blink to show that code transfer is ready.■While keeping the transmitter (L) button pressed, press andhold the button on the new transmitter (R) that you want totransfer the active code to.■Code transfer will occur in approximately 2 seconds. If the new transmitter (R) is a Midi or a Mini, the indicator light willilluminate continuously to show that transfer is complete.■All buttons can be released. Code transfer is completed.■Cable can be removed and the covers replaced.■Both transmitters can now be used to operate the same door.Note: For multi-button transmitters, be sure to carry out this procedure for all the buttons you desire to use. For micro transmitters, follow the same steps only there willbe no LED light indication.5. Changing the Code on TransmittersThe transmitter factory preset code can be changes as follows:FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.8030012 © 2001 All rights reserved. 01/01 Marantec America Corporation, 675 Heathrow Dr., Lincolnshire, IL 60069 1-888-622-2489Transmitterwith ActiveCodeNewTransmitterFigure 3. Multiple Transmitters—CodeTransferLRLRLRLightBlinks LightBlinksLightOff LightIllunimatesContinuouslyPress Firstand hold Press Secondand hold Keep Pressed Release whenLight IllunimatesContinuouslyTransmittersInstructions (continued)■Remove battery cover from compartment.■Connect the programming 3-prongcable to programming terminal intransmitter. Fig. 3A.■Cross any two wires of the program-ming cable, one of them must be thecenter wire.■Press and hold the button on thetransmitter.■Code will change in approximately 2seconds.■Release the button after the light illu-minates continuously then remove thecable and replace the cover.Note: For multi-button transmitters, be sure to carry out this procedure for all the buttons you desire to use. For micro transmitters, follow the same steps only there willbe no LED light indication.LIMITED WARRANTY: Transmitters (model #’s ML-143(1,2,4), ML-243(1,2,4), ML-343(1), ML-140(1,2,4), ML-240(1,2,4), ML-139(1,2,4), ML-239(1,2,4) - (1) Year Warranty(Labor not included)COVERAGE: Any defect in material and or workmanship from personal,normal household use in accordance with the Owner‘s Manual.WARRANTY OWNERSHIP: The warranty is limited to the consumer whooriginally purchased and/or registered the product.MARANTECAMERICA CORPORATION COMMITMENT: If the Marantec®product is found to be defective, we will repair or, at our option, replaceit at no charge to the customer. We may elect to use new or recondi-tioned replacement parts or product of the same or similar design atthat given time.LIMITATIONS: Marantec®will not be liable for loss or damage to prop-erty or any incidental or consequential loss or expense from propertydamage due directly or indirectly from the use of this product otherthan in the States that do not allow such exclusion of limitation.Marantec®will not cover batteries, unauthorized repair parts, installa-tions, commercial use, damage while in transit, defects resulting fromaccidents, or resulting from alterations, lack of proper maintenance,unauthorized repair or modification of product, misuse or abuse ofproduct, fire, flood, or acts of God, or other failures due to not properlyfollowing the Marantec® Owner‘s Manual. No labor costs are covered.This warranty applies only to Marantec®’sAccessories purchased andused in the United States, Canada, or Mexico. Marantec® under no cir-cumstances will be liable for consequential, incidental or special dam-ages arising in connection with the use, or inability to use, this product.In no event shall Marantec®’s liability for breach of warranty, breach ofcontract, negligence or strict liability exceed the cost of the productcovered hereby. No person is authorized to assume for MarantecAmerica Corporation any other liability in connection with the sale ofthis product. WARRANTY SERVICE: Service from Authorized Dealers: Contact thesource that sold you and/or installed your Garage Door Opener unit.Self-Service: Call Marantec®’s Toll Free Helpline at: 1-888-622-2489 wherea trained Marantec®representative will assist you in diagnosing and providing you with directions and parts to repair it yourself if possible.Figure 3A. Code Changing

Navigation menu