Marantec America D304315 Remote Control Transmitter User Manual 65895

Marantec America Corporation Remote Control Transmitter 65895

Users Manual

Transmitters Instructionsfor models: M3-2312, M3-2314, M3-3313 FEATURESMini (2- or 4-channel) Micro (3-channel), the smallest transmitter of its kind.3. Battery Replacement (fig. 2)Open the transmitter by using small coin. The installation of the battery for Mini and Micro is the same. When replacing batteries follow the steps below:Close the transmitter. Note: Replace batteries with same type only.Insert a 3V battery (type CR2032) as shown. 1. Using the Transmitter2. Transmitter Mounting (fig. 1)Mounting Plate (fig. 1A)The mounting plate enables you to mount the transmitter easilyto the wall or other area.Secure the mounting plate to area using screw and anchor(not provided).Visor Clip (fig. 1B)Key Ring Attachment (fig. 1C)The transmitters can be convenietly mounted on the wall (fig. 1A) using the mounting plate (optional) or inside your car using the visor clip (fig. 1B). These two mounting alternatives (fig. 1a and fig. 1B) are available with Mini models only. The Micro can be used with the key ring attachment (fig. 1C).Slide the transmitter into the mounting plate, which will hold it firmly in place. Open the Micro by using small coin.Snap in the key ring attachment.Close the transmitter.To open or close garage door, press and hold the button (Mini and Micro transmitters have indicator lights). When garage door begins to move release button.To stop the garage door during travel, press and hold button until door stops, then release button.To continue the garage door travel after stopping it, press and hold the button. Press button once, the door will travel in the opposite direction.The visor clip allows for easy mounting of the transmitter to a car visor.The key ring attachment permits easy mounting of the Micro to a key ring.Snap visor clip into transmitter.Note: If you do not need the visor clip, install the visorcompartment cover. Figure 2. Battery CompartmentCoinBatteryFigure 1. Mounting Plate & Visor Clipfig. 1Afig. 1Bfig. 1C Key Ring Attachment for Micro Transmitter A family of state-of-the-art transmitters, each transmitter is custom encoded and ergonomically designed to be an integral part of your garage door opener system, with two styles to suit your personal preference:Visor Compartment CoverVisor ClipKey RingAttachmentAll transmitters come with batteries already installed. Mounting Plate (optinal)
4. Multiple TransmittersEach transmitter comes factory programmed with random codes. 2-channel transmitters have 2 different random codes, one per button, 3-channel transmitters have 3 different random codes and 4-channel transmitters have 4 different random codes, one per button. Transmitters that are purchased separately as accessories have random codes that must be changed in order to match the code of the "active" transmitter, which you are alredy using. Below are instructions for transferring an active code from a button on one transmitter to a button of your choice on another transmitter. Connect the transmitter with active code to the new transmitter using the programming connector (fig. 3A).Press and hold the selected channel button on the transmitter with the active code (fig. 3B). The light in the transmitter illuminates.Press and hold the respective channel button on the new transmitter (fig. 3C). The light in the transmitter initially starts blinking and then illuminates continuously after 1-2 sec. Code transfer is completed.Programming conn ector can be removed and both transmitters can now be used to operate the same door.Note: For multi-button transmitters, be sure to carry out this procedure for all the buttons you desire to use.5. Changing the Code on TransmittersThe transmitter factory preset code can be changes as follows:Connected the programming connector into the lateral socket of the transmitter to be changing the code (fig. 4).Short one of the outer pins of the programming connector with the middle pin.Press and hold the respective channel button. The light will blink rapidly for approx. 5 sec. Release the button after the light illuminates continuously. Then remove the programming connector. Note: For multi-button transmitters, be sure to carry out this procedure for all the buttons you desire to use.Figure 3. Multiple Transmitters-Code TransferTransmitter with active Codenew TransmitterProgramming Connectorfig. 3Afig. 3Bfig. 3CFigure 4. Code ChangingFCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.65895 2003 All rights reserved. 05/03 Marantec America Corporation, 675 Heathrow Dr., Lincolnshire, IL 60069 1-888-622-2489©Transmitters Instructions(continued)

Navigation menu