Marantz Rx8001 Users Manual RX8001_SG_EFS
RX8001 to the manual f79f2671-dd17-4006-8656-efe402e2ab8b
2015-02-03
: Marantz Marantz-Rx8001-Users-Manual-466496 marantz-rx8001-users-manual-466496 marantz pdf
Open the PDF directly: View PDF 
.
Page Count: 20
Model RX8001 User Guide
Wireless Extender
ENGLISH
FRANÇAIS
ESPAÑOL
Concept and realisation of the Guide:
Concept et réalisation du guide :
Concepto y realización de la Guía:
Human Interface Group, De Regenboog 11, 2800 Mechelen (Belgium)
www.higroup.com
3104 205 3442.1
WARNINGS
• Do not expose the equipment to rain or moisture.
• Do not remove the cover from the equipment.
• No naked flame sources, such as lighted candles, should be placed on the equipment.
• No objects filled with liquids, such as vases, shall be placed on the equipment.
AVERTISSEMENTS
• Ne pas exposer l’appareil à la pluie ni à l’humidité.
• Ne pas essayer de retirer le boîtier de l’appareil.
• Ne placer aucune source de flamme nue, comme une bougie allumée, sur l'appareil.
• Aucun objet rempli de liquide, un vase par exemple, ne doit être placé sur l'appareil.
ADVERTENCIAS
• No exponga el equipo a la lluvia ni a la humedad.
• No extraiga la tapa del equipo.
• No deben colocarse sobre el equipo elementos con fuego, por ejemplo velas encendidas.
• No se deben colocar sobre el aparato recipientes que contengan líquidos, como por ejemplo
jarrones.
EN
FR
ES
ENGLISH
RX8001 User Guide
FRANÇAISESPAÑOL
RX8001 User Guide
1
RX8001 User Guide
RX8001 User Guide
Contents
Before You Start..............................................2
Unpacking the Extender ...................................3
Configuring the Extender ..................................4
Stand-alone Connection ...............................4
Network Connection....................................4
Installing the Extender .....................................6
Connecting the Extender to A/V equipment .......6
Support..........................................................7
Troubleshooting..........................................7
Firmware Update ........................................9
Specifications ...............................................10
IFU Approbation / Safety Content RX8001 ............i
FCC Compliancy ..........................................i
Regulations According to R&TTE. . . . . . . . . . . . . . . . . . . . . ii
Stand-alone Mode
Network Mode
ENGLISH
2
RX8001 User GuideRX8001 User Guide
Before You Start
The Wireless Extender is an important element of the RC9001 and makes it possible to
control A/V equipment via RF in the entire house.
In order to use the Extender in a wireless Network:
•Configure the Extender: connect it to the PC and use the Configuration Tool.
•Install the Extender: connect it to external A/V equipment, like a TV or receiver.
The Extender can be used in two ways:
Stand-alone Mode
This is the so-called ‘Ad-Hoc Mode’: a router is not required.
Stand-alone Advantages:
• The Extender is easily configured and installed.
• It operates independently from other networks and network settings.
Refer to the chapter
‘Stand-alone Connection’
on page 4 to configure the Extender in Stand-alone
Mode.
Note If you want to use a Multimedia server, like the Escient Fireball, in combination with one or
more Extenders, the Extenders have to be configured in Network Mode.
Network Mode
This is the so-called ‘Infrastructure Mode’: the Extender is used in a network with a router.
Network Advantages:
• A network allows the use of repeaters, which enlarges the range of the RC9001 System.
• When using a dedicated Network, the Extender can operate independently from settings
in other networks.
• The Extender in Network Mode can be given a fixed IP address, which increases reliability.
• The network connection can be encrypted.
Refer to the chapter ‘
Network Connection’
on page 4 to configure the Extender in Network Mode.
Note An Extender that has been configured in Stand-alone Mode can always be reconfigured for use
in Network Mode and vice versa.
You can use up to 16 different Extenders in the same Network.
3
RX8001 User Guide
Unpacking the Extender
Wireless Extender
Front Panel
Antenna
Configuration switch
• In Stand-alone Mode:
changes the RF
channel.
• In Network Mode:
indicates the
connection type.
IP address
Power input
4 IR outputs
4 dipswitches for
the IR outputs
Back Panel
Extender ID switchEthernet input
(RJ45)
Stand-alone/
Network switch
2 Dual IR Emitters 2 Mini-jack IR Cables
Power Adapter Configuration Cable
Crossed Ethernet cable
WiFi LED
Ethernet LED
Busy LED
Power LED
ENGLISH
4
RX8001 User Guide
Configuring the Extender
Note Before you start configuring the Extender, check for firmware updates in the Downloads section
on http://www.marantz.com in the Home Entertainment section of your region.
Refer to the chapter ‘Firmware Update’ on page 9 for further details.
Stand-alone Connection
To configure the Stand-alone Extender:
1Plug in the Extender’s power adapter.
The Extender will start up. When start-up has finished, the Power and WiFi LEDs are green.
2Use the default switch settings of the Extender:
Note • If there is already an Extender with ID 0, set the Extender ID switch to an ID that is not
used yet.
• If there is any interference with other products in or around the house, the
Configuration switch can be set to a different RF channel.
• Make sure the same Extender ID and RF channel are used on the Extender and the
Control Panel.
3Configure the Control Panel’s configuration file so that the Control Panel can work
with the Extender. For more details, refer to the Wizz.it Ex Online Help.
Network Connection
In the case of a network connection, the Extender is made part of the wireless Network.
There are two ways to use the Extender in a network:
•Wired connection
•Wireless connection
Stand-alone/Network Stand-alone
Configuration switch 1
Extender ID 0
Extender
Router
Wireless
Access Point
Straight Ethernet Cable
Extender
Wireless
Access Point
Control Panel
Control Panel
Note When you set up a Wireless Network connection, make sure the Control Panel
always shows minimal one bar of WiFi connectivity. If this is not the case, you may need
additional Wireless Access points in your network.
5
RX8001 User Guide
To configure the Network Extender:
1Connect the Extender to the PC with the
configuration cable (this is the crossed
Ethernet cable enclosed).
2Set the switches correctly:
Note • If there is already an Extender with ID 0, set the Extender ID switch to an ID that is not
used yet.
• Make sure the same Extender ID is used on the Extender and the Control Panel.
3Plug in the Extender’s power adapter.
The Extender will start up. After startup, the Power and Ethernet LEDs are green and the Busy
LED is red/green blinking.
4Open the browser.
5Type the IP address of the Extender 192.168.8.80 (printed on the back of the Extender)
in the address bar of the browser.
The Configuration Tool opens in the browser.
6Follow the onscreen instructions and make sure you have the following information at
hand:
• If the Extender will be connected wirelessly to the Network: the SSID and
encryption settings (WPA encryption is currently not supported.)
• If the Extender will be operating with a fixed IP address: the IP address,netmask and
default gateway.
Tip To ensure optimal performance, use a dedicated network for all communication.
This makes the Network independent from other network traffic and changes in
network settings.
7Disconnect the Extender from the PC.
8Connect the Extender to the Network:
• For a wired connection, connect the Extender to the router by means of a straight Ethernet
cable.
• For a wireless connection, you do not need to connect any more cables.
9Set the switches correctly:
The Extender will restart. After startup,
• In a wired network connection, the Power and Ethernet LEDs are green and the Busy LED
blinks green when it’s processing a code or a macro from the Control Panel.
• In a wireless network connection, the Power and WiFi LEDs are green and the Busy LED
blinks green when it’s processing a code or a macro from the Control Panel.
Extender Configuration
cable
Stand-alone/Network Network
Configuration switch 2
Extender ID 0
Stand-alone/Network Network
Configuration switch 1
Extender ID 0
ENGLISH
6
RX8001 User Guide
Configuring the Extender through a Router
When the Extender is already installed and connected to external A/V equipment, it is possible to
configure it through a router via a straight Ethernet cable. It is not possible to configure the
Extender wireless via the router.
1Connect the Extender to the router, and the router to the PC, as indicated below.
2Set the Extender’s Configuration switch to 3.
3Open the Wizz.it Ex on the PC.
4In the Tools menu, select Extender Discovery.
The Extender Discovery tool appears, with a list of all the detected Extenders in the
Network.
5Select the Extender that you want to configure and click on the Configure button.
The Configuration Tool opens in the browser.
6Finalize the configuration, as described in the instructions on page 5.
Installing the Extender
Warning
Keep the Extender away from heat sources such as amplifiers.
Before connecting the Extender to external A/V equipment,
make sure that the antenna is placed correctly.
Connecting the Extender to A/V equipment
For the Extender to transmit an IR signal, you need to connect it to the A/V component via the
IR Output on the back of the Extender. In contrast to previous Marantz Extenders, the RX8001 has no
IR blaster.
To connect the Extender to A/V equipment, use one of the following cables enclosed with the
Extender:
• a Dual IR emitter;
Place the
antenna in an
upright position.
Extender
Straight
Ethernet cable
Router
Insert the mini-jack
connector of the
Dual IR emitter in
the IR output of
the Extender.
Attach the
emitter to the
infrared receiver
of the A/V
component.
Tip When the Extender is not recognized by the Extender Discovery tool, configure the Extender
directly with the configuration cable, as described on page 5.
7
RX8001 User Guide
LEDs
Colors Ethernet LED WiFi LED Busy LED
The Extender’s IP address is
being determined.
Green blinking The Extender’s IP address is
being determined.
The Extender is busy processing
a short code or macro from the
Control Panel.
The Extender is functioning
normally.
Green The Extender is functioning
normally.
The Extender is busy processing
a long macro from the Control
Panel.
–
Red/green blinking – The Extender is being
configured.
Refer to the topic ‘
There is an
IP conflict’
on page 7.
Red Refer to the topic
‘
The Extender cannot
communicate with the
wireless network’
on page 8.
Refer to the topic ‘
There are
duplicate Extender IDs’
on page 8.
Refer to the topic ‘
The IP address
cannot be determined’
on
page 7.
Red blinking The Extender is starting up.
Wait until startup has finished.
-or-
• a mini-jack IR cable.
Adjusting the Power Level of the IR Outputs
At the back of the Extender, there are 4 dipswitches, one for each IR output. Use these dipswitches
to configure the power level of the Dual IR emitters and the mini-jack cables.
For example, flip the dipswitch down to lower the power level when the Extender is connected to
an external IR bus system.
Support
Troubleshooting
What Do the LEDs Indicate?
Insert one mini-jack
connector of the
mini-jack cable in
the IR output of the
Extender.
Insert the other
mini-jack
connector in the
A/V component.
There is an IP conflict
There is another A/V component in the network that is using the same fixed IP address as the
Extender. Change the IP address of the Extender in the Configuration Tool.
If the problem persists, check the router settings.
The IP address cannot be determined
• When using the Extender: make sure that the Extender is connected to the router with a straight
Ethernet cable.
• When configuring the Extender: make sure the PC is not using a fixed IP address but is using
DHCP instead.
ENGLISH
8
RX8001 User Guide
• Make sure the router is switched on. If the router is using DHCP, the Extender’s IP address cannot
be determined. Make sure to use the correct network settings on the router.
The Extender cannot communicate with the wireless network
The WiFi LED is red
• Make sure that the Extender is in range of the Wireless Access Point.
• Make sure that you filled in the correct secret in the Configuration Tool.
• Add the Extender’s MAC address to the router’s list of accepted MAC addresses.
The WiFi LED is red blinking
• Check the router’s network settings and make sure that it can operate with the Extender.
• If the LED doesn’t stop blinking, unplug the power adapter, wait a few seconds, and plug it in
again.
Finding the Exact Location of an A/V component’s IR Receiver
1Remove the protective tape of the Dual IR emitters.
2Set the Dual IR emitters to the minimal power level, and hold the adhesive side of one
of the emitters 0.4 - 0.8 inch / 1 - 2 cm in front of the A/V component.
3Make sure the Control Panel is configured to operate with the A/V component.
4Move the emitter across the front panel of the A/V component, and at the same time,
send commands with the Control Panel to the A/V component.
Take note of when the A/V component reacts to the IR signals of the emitter.
5When the A/V component reacts, position the emitter in that place.
Operating A/V components with the Extender
The A/V components do not respond to commands from the Extender
• Check if the Busy LED blinks green when you send a command with the Control Panel. If the Busy
LED does not blink, the Extender is not receiving commands from the Control Panel;
• Make sure that the Control Panel is configured correctly in Wizz.it Ex;
• Make sure that the Extender is configured correctly in the Configuration Tool and connected
properly to the A/V components;
• Make sure that the switches on the Extender are set correctly.
• Make sure that the Wireless Access Point is on and configured correctly.
• Make sure that the Extender is in range of the Wireless Access Point. If the Wireless Access
Point is placed higher or lower than the Extender, place the Extender’s antenna horizontally for
optimum range.
• Not all Wireless Access Points are working equally well in combination with the Control Panel.
Make sure you use a quality access point.
There are duplicate Extender IDs
Using the Extender ID switch, assign a unique ID to each Extender in the same Network.
Make sure the Control Panel is configured accordingly in Wizz.it Ex.
You can use up to 16 different Extenders in the same Network.
The Busy LED blinks green when the Control Panel is not in use
This does not mean that something is wrong with the Extender. It merely indicates that the Extender
is being operated by a different Control Panel. When the Busy LED stops blinking, you can use the
Extender again.
9
RX8001 User Guide
Resetting the Extender
This is only necessary when the Extender displays unusual behavior.
To perform a reset, unplug the Extender from the electrical socket. Wait a few seconds, and plug it
in again.
Firmware Update
When an update of the Extender firmware is available, this will be announced on the Marantz
website: http://www.marantz.com.
Note You can always see the current version of the firmware in the Configuration Tool.
1Download the new version of the firmware on the PC.
2Unplug the Extender. The Extender can be updated in the following ways.
Updating the Extender with the configuration cable
1Connect the Extender to the PC with the configuration cable.
2Set the switches correctly.
3Open the browser.
4Type the IP address of the Extender: 192.168.8.80 (printed on the back of the Extender)
in the address bar of the browser.
The Configuration Tool opens in the browser.
5Select Firmware Update in the left navigation pane.
The Firmware Update page opens.
6Follow the onscreen instructions.
When you are asked to browse to the update file, you need to select the ZIP file you
downloaded earlier from the website.
Updating the Extender through a router
If the Extender is already installed and connected to A/V equipment, it may be more convenient to
update it through a router via a straight Ethernet cable. It is not possible to configure the Extender
wireless via the router.
1Connect the Extender to the router, and the router to the PC.
2Set the switches correctly.
3Open the Wizz.it Ex on the PC.
4In the Tools menu, select Extender Discovery.
The Extender Discovery tool appears, with a list of all the detected Extenders in the
Network.
Stand-alone/Network Network
Configuration switch 2
Extender ID 0
Stand-alone/Network Network
Configuration switch 3
Extender ID 0
ENGLISH
10
RX8001 User Guide
5Select the Extender that you want to configure and click on the Configure button.
The Configuration Tool opens in the browser.
6Select Firmware Update in the left navigation pane.
The Firmware Update page opens.
7Follow the onscreen instructions.
When you are asked to browse to the update file, you need to select the ZIP file you
downloaded earlier from the website.
Tip When your Extender is not recognized by the Extender Discovery tool, update the Extender
with the crossed Ethernet cable, as described on page 9.
Specifications
The specifications and design of this product are subject to change without notice.
General Dark grey ABS housing with poly carbonate front plate
802.11 b/g compliant RF technology
4 LED indications for Power, WiFi, Network and Busy
Up to 16 extenders and 16 control panels in a system (for all modes)
4 addressable outputs for IR emitters
Ethernet RJ45 connection
Rotatable RF antenna
Positioning: freestanding or mounted in any position
Modes Stand-alone (wireless): Similar to WiFi ad-hoc mode; no access point and
router required
Network (wireless): Similar to WiFi infrastructure mode; used in a system with
a router and access point
Network (wired via Ethernet): used in a system with a router and access point
Dimensions 3,98 x 6,18 x 1,3 inch (101,2 x 157 x 33,5 mm)
Operating temperature 32°F to 122°F (0°C to 50°C)
Infrared (IR) IR frequency range: 25kHz-1MHz (including DC/flash codes)
IR power out: 2 levels
Radio Frequency (RF) 802.11g at 2.4 GHz with additional proprietary protocol
Dual IR emitters Number of IR emitters: up to 4 (2x2), emitters wired in series
0.13 inch (3.5 mm) mono mini-jack
Cable length: 9 ft (2.7 meters)
Mono mini-jack cables 0.13 inch (3.5 mm) mono mini-jack
Cable length: 5 ft (1.5 meters)
Power adapter 100V-240 VAC / 50-60 Hz Power adapter (5 VDC/2A output, UL-CE approved)
Accessories Warranty certificate (For USA/Canada only)
Wireless Extender User Guide
© Marantz Brand Company – A division of D&M Holdings Inc. D&M Building, 2 -1 Nisshin-CHO, Kawasaki-KU, Kawasaki-
SHI, Kanagawa, 210-8569, Japan.
Remarks:
All rights are reserved. Reproduction in whole or in part is prohibited without prior consent of the copyright owner.
Marantz Brand Company – A division of D&M Holdings Inc. is not liable for omissions or for technical or editorial errors
in this manual or for damages directly or indirectly resulting from the use of the Wireless Extender.
The information in this User Guide may be subject to change without prior notice. All brand or product names are
trademarks or registered trademarks of their respective companies or organizations.
FCC Compliancy
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC rule.
These limits are designed to provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a different circuit from the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION The user changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice for Canada / Remark pour le Canada
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada
Regulations According to R&TTE
Declaration
Hereby, Marantz Europe, a division of D&M Europe B.V. declares that RX8001 is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC:
• Radio: EN 300 328
• EMC: ETSI EN 301 489-1, ETSI EN 301 489-17
• Safety: EN60950-1
Česky My, Marantz Europe, a division of D&M Europe B.V., prohlašujeme že výrobek RX8001 splňuje základní
požadavky a ostatní příslušná ustanovení Směrnice 1999/5/EC.
Dansk Marantz Europe, a division of D&M Europe B.V., erklærer herved, at følgende udstyr RX8001
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Marantz Europe, a division of D&M Europe B.V., dass sich dieses Gerät (RX8001) in
Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet". (BMWi).
Eesti keeles Käesolevaga kinnitab Marantz Europe, a division of D&M Europe B.V. et see RX8001 vastab Euroopa
Nõukogu direktiivi 1999/5/EC põhinõuetele ja muudele olulistele tingimustele.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Marantz Europe, a division of D&M Europe B.V. ∆ΗΛΩΝΕΙ ΟΤΙ RX8001
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ
ΤΗΣ Ο∆ΗΛΙΑΣ 1999/5/ΕΚ.
Español Por medio de la presente Marantz Europe, a division of D&M Europe B.V. declara que RX8001 cumple
con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva
1999/5/CE.
IFU Approbation / Safety Content
i
Français Par la présente Marantz Europe, a division of D&M Europe B.V., déclare que les appareils du type
RX8001 sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano Con la presente Marantz Europe, a division of D&M Europe B.V., dichiara che questo RX8001 è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Magyar A gyártó Marantz Europe, a division of D&M Europe B.V., kijelenti, hogy ez a RX8001 megfelel az
1999/5/EK irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.
Nederlands Hierbij verklaart Marantz Europe, a division of D&M Europe B.V., dat deze RX8001 in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Polski Niniejszym firma Marantz Europe, a division of D&M Europe B.V., oświadcza, że RX8001 spełnia
wszystkie istotne wymogi i klauzule zawarte w dokumencie „Directive 1999/5/EC”.
Português Marantz Europe, a division of D&M Europe B.V., declara que este RX8001 está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensky Výrobca Marantz Europe, a division of D&M Europe B.V. týmto deklaruje, že táto RX8001 je v súlade so
základnými požiadavkami a ďalšími relevantnými predpismi smernice 1999/5/EC.
Slovensko Marantz Europe, a division of D&M Europe B.V. s tem potrjuje, da je ta RX8001 skladen/a z osnovnimi
zahtevami in ustreznimi določili Direktive 1999/5/EC.
Suomi Marantz Europe, a division of D&M Europe B.V., vakuuttaa täten että RX8001 tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska Härmed intygar, Marantz Europe, a division of D&M Europe B.V., att denna RX8001 står i
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
Declaration of Conformity(DoC)
The Declaration of Conformity of this product can be found at: http://www.marantz.com/download/RX8001.
Marking
In line with CE marking regulations: the CE mark and the class 2 identifier are added to the equipment:
Czech Likvidace starého výrobku
Tento výrobek je navržen a vyroben z materiálů a komponentů nejvyšší kvality, které je možné recyklovat a
opětovně použít. Pokud je výrobek označen tímto symbolem přeškrtnutého kontejneru, znamená to, že
výrobek podléhá směrnici EU 2002/96/EC. Informujte se o místním systému sběru tříděného odpadu
elektrických a elektronických výrobků. Postupujte podle místních pravidel a neodkládejte takové staré
výrobky do běžného komunálního odpadu. Správná likvidace starého výrobku pomůže předcházet
případným nepříznivým účinkům na životní prostředí a lidské zdraví.
Danish Bortskaffelse af dit gamle produkt
Dit produkt er konstrueret med og produceret af materialer og komponenter af høj kvalitet, som kan
genbruges. Når dette markerede affaldsbøttesymbol er placeret på et produkt betyder det, at produktet er
omfattet af det europæiske direktiv 2002/96/EC. Hold dig orienteret om systemet for særskilt indsamling af
elektriske og elektroniske produkter i dit lokalområde. Overhold gældende regler, og bortskaf ikke dine
gamle produkter sammen med dit almindelige husholdningsaffald. Korrekt bortskaffelse af dine gamle
produkter er med til at skåne miljøet og vores helbred.
This device can be used in the following countries:
AT ✔BE ✔CH ✔DE ✔DK ✔GR ✔ES ✔FI ✔
FR ✔IRE ✔IT ✔LU ✔NL ✔PT ✔SE ✔UK ✔
ii
Dutch Verwijdering van uw oude product
Uw product is vervaardigd van kwalitatief hoogwaardige materialen en onderdelen, welke gerecycled en
opnieuw gebruikt kunnen worden. Als u op uw product een doorstreepte afvalcontainer op wieltjes ziet,
betekent dit dat het product valt onder de EU-richtlijn 2002/96/EC. Win inlichtingen in over de manier
waarop elektrische en elektronische producten in uw regio gescheiden worden ingezameld. Neem bij de
verwijdering van oude producten de lokale wetgeving in acht en plaats deze producten niet bij het gewone
huishoudelijke afval. Als u oude producten correct verwijdert voorkomt u negatieve gevolgen voor het
milieu en de volksgezondheid.
Finnish Vanhan tuotteen hävittäminen
Tuotteesi on suunniteltu ja valmistettu laadukkaista materiaaleista ja komponenteista, jotka voidaan
kierrättää ja käyttää uudelleen. Tuotteeseen kiinnitetty yliviivatun roskakorin kuva tarkoittaa, että tuote
kuuluu Euroopan parlamentin ja neuvoston direktiivin 2002/96/EC soveltamisalaan. Ota selvää
sähkölaitteille ja elektronisille laitteille tarkoitetusta kierrätysjärjestelmästä alueellasi. Noudata paikallisia
sääntöjä äläkä hävitä vanhoja tuotteita tavallisen talousjätteen mukana. Vanhojen tuotteiden hävittäminen
oikealla tavalla auttaa vähentämään ympäristölle ja ihmisille mahdollisesti koituvia haittavaikutuksia
French Mise au rebut des produits en fin de vie
Ce produit a été conçu et fabriqué avec des matériaux et composants recyclables de haute qualité. Le
symbole d’une poubelle barrée apposé sur un produit signifie que ce dernier répond aux exigences de la
directive européenne 2002/96/EC. Informez-vous auprès des instances locales sur le système de collecte
des produits électriques et électroniques en fin de vie. Conformez-vous à la législation en vigueur et ne
jetez pas vos produits avec les déchets ménagers. Seule une mise au rebut adéquate des produits peut
empêcher la contamination de l’environnement et ses effets nocifs sur la santé.
German Entsorgung Ihres alten Geräts
Ihr Gerät wurde unter Verwendung hochwertiger Materialien und Komponenten entwickelt und hergestellt,
die recycelt und wieder verwendet werden können. Befindet sich dieses Symbol (durchgestrichene
Abfalltonne auf Rädern) auf dem Gerät, bedeutet dies, dass für dieses Gerät die Europäischen Richtlinie
2002/96/EG gilt. Informieren Sie sich über die geltenden Bestimmungen zur getrennten Sammlung von
Elektro- und Elektronik-Altgeräten in Ihrem Land. Richten Sie sich bitte nach den geltenden Bestimmungen
in Ihrem Land, und entsorgen Sie Altgeräte nicht über Ihren Haushaltsabfall. Durch die korrekte Entsorgung
Ihrer Altgeräte werden Umwelt und Menschen vor möglichen negativen Folgen geschützt.
Greek
Αόρριψη αλιού ροόντοσ
Το ροόν αυτό έχει σχεδιαστεί και κατασκευαστεί µε υψηλήσ οιότητασ υλικά και εξαρτήµατα
ου µορούν να ανακυκλωθούν και να ξαναχρησιµοοιηθούν. Όταν ένα ροόν φέρει την
ένδειξη ενόσ διαγραµµένου κάδου µε ρόδεσ, τότε το ροόν αυτό καλύτεται αό την Οδηγία
2002/96/ΕΚ. Παρακαλούµε να ενηµερωθείτε σχετικά µε το τοικό σύστηµα ξεχωριστήσ
συλλογήσ ηλεκτρικών και ηλεκτρονικών ροόντων. Παρακαλούµε να ακολουθείτε την τοική
νοµοθεσία και να µην αορρίτετε τα αλιά σασ ροόντα µαζί µε τα οικιακά σασ
αορρίµµατα. Η σωστή µέθοδοσ αόρριψησ των αλιών σασ ροόντων θα συµβάλει στην
αοφυγή αρνητικών ειτώσεων στο εριβάλλον και την ανθρώινη υγεία.
Hungarian Az elhasznált termék hulladékkezelése
Ezt a terméket minőségi, újrafeldolgozható és újrahasznosítható anyagok és alkatrészek felhasználásával
tervezték és készítették. A termékhez kapcsolódó áthúzott kerekes kuka szimbólum azt jelenti, hogy a
termékre vonatkozik a 2002/96/EK. Európai irányelv. Kérjük, informálódjon az elektromos és elektronikus
hulladékok szelektív gyűjtésének helyi rendszeréről. Kérjük, a helyi szabályok figyelembe vételével járjon
el, és ne dobja az elhasznált terméket a háztartási hulladékgyűjtőbe. Az elhasznált termék megfelelő
hulladékkezelése segítséget nyújt a környezettel és az emberi egészséggel kapcsolatos esetleges negatív
következmények megelőzésében.
Italian Smaltimento di vecchi prodotti
Il prodotto è stato progettato e assemblato con materiali e componenti di alta qualità che possono essere
riciclati e riutilizzati. Se su un prodotto si trova il simbolo di un bidone con ruote, ricoperto da una X, vuol
dire che il prodotto soddisfa i requisiti della Direttiva comunitaria 2002/96/CE. Informarsi sulle modalità di
raccolta, dei prodotti elettrici ed elettronici, in vigore nella zona in cui si desidera disfarsi del prodotto.
Attenersi alle normative locali per lo smaltimento dei rifiuti e non gettare i vecchi prodotti nei normali
rifiuti domestici. Uno smaltimento adeguato dei prodotti aiuta a prevenire l’inquinamento ambientale e
possibili danni alla salute.
IFU Approbation / Safety Content
iii
Norwegian Avhending av gamle produkter
Produktet er utformet og produsert i materialer og komponenter av høy kvalitet, som kan resirkuleres og
brukes på nytt. Når denne søppelbøtten med kryss på følger med et produkt, betyr det at produktet dekkes
av det europeiske direktivet 2002/96/EU. Finn ut hvor du kan levere inn elektriske og elektroniske produkter
til gjenvinning i ditt lokalmiljø. Overhold lokale regler, og ikke kast gamle produkter sammen med
husholdningsavfallet. Riktig avhending av de gamle produktene dine vil hjelpe til med å forhindre
potensielle negative konsekvenser for miljøet og menneskers helse.
Polish Usuwanie zużytych produktów
Niniejszy produkt został zaprojektowany i wykonany w oparciu o wysokiej jakości materiały i podzespoły,
które poddane recyklingowi mogą być ponownie użyte. Jeśli na produkcie znajduje się symbol
przekreślonego pojemnika na śmieci na kółkach, podlega on postanowieniom dyrektywy 2002/96/WE.
Należy zapoznać się lokalnymi zasadami zbiórki i segregacji sprzętu elektrycznego i elektronicznego.
Należy przestrzegać lokalnych przepisów i nie wyrzucać zużytych produktów elektronicznych wraz z
normalnymi odpadami gospodarstwa domowego. Prawidłowe składowanie zużytych produktów pomaga
ograniczyć ich szkodliwy wpływ na środowisko naturalne i zdrowie ludzi.
Portuguese Eliminação do seu antigo produto
O seu produto foi desenhado e fabricado com matérias-primas e componentes de alta qualidade, que
podem ser reciclados e reutilizados. Quando este símbolo, com um latão traçado, está afixado a um
produto significa que o produto é abrangido pela Directiva Europeia 2002/96/EC. Informe-se acerca do
sistema de recolha selectiva local para produtos eléctricos e electrónicos. Aja de acordo com os
regulamentos locais e não descarte os seus antigos produtos com o lixo doméstico comum. A correcta
eliminação do seu antigo produto ajuda a evitar potenciais consequências negativas para o meio ambiente
e para a saúde pública.
Slovak Likvidácia tohto produktu
Váš produkt bol navrhnutý a vyrobený pomocou vysokokvalitných materiálov a komponentov, ktoré sa
dajú recyklovať a znova využiť. Keď sa na produkte nachádza symbol prečiarknutého koša s kolieskami,
znamená to, že tento produkt pokrýva Európska smernica 2002/96/EC. Informujte sa o miestnom systéme
separovaného zberu elektrických a elektronických výrobkov. Postupujte podľa miestnych pravidiel a
nevyhadzujte tento produkt do bežného odpadu z domácnosti. Správnou likvidáciou starého produktu
pomôžete zabrániť možným negatívnym následkom na životné prostredie a ľudské zdravie.
Slovenian Odlaganje starega izdelka
Izdelek je zasnovan in izdelan iz visokokakovostnih materialov in komponent, ki jih je mogoče reciklirati in
ponovno uporabiti. Če je izdelek označen s prečrtanim košem za smeti, to pomeni, da je v skladu z
Direktivo EU 2002/96/ES. Seznanite se z lokalnim sistemom za zbiranje odpadnih električnih in
elektronskih komponent. Upoštevajte lokalne predpise in izrabljenega izdelka ne odlagajte z običajnimi
gospodinjskimi odpadki. S pravilnim odlaganjem izrabljenih izdelkov pomagate preprečevati negativne
posledice na okolje in zdravje ljudi.
Spanish Desecho del producto antiguo
El producto se ha diseñado y fabricado con materiales y componentes de alta calidad, que se pueden
reciclar y volver a utilizar. Cuando este símbolo de contenedor de ruedas tachado se muestra en un
producto indica que éste cumple la directiva europea 2002/96/EC. Obtenga información sobre la recogida
selectiva local de productos eléctricos y electrónicos. Cumpla con la normativa local y no deseche los
productos antiguos con los desechos domésticos. El desecho correcto del producto antiguo ayudará a
evitar consecuencias negativas para el medioambiente y la salud humana.
Swedish Kassering av din gamla produkt
Produkten är utvecklad och tillverkad av högkvalitativa material och komponenter som kan både återvinnas
och återanvändas. När den här symbolen med en överkryssad papperskorg visas på produkten innebär det
att produkten omfattas av det europeiska direktivet 2002/96/EG. Ta reda på var du kan hitta närmaste
återvinningsstation för elektriska och elektroniska produkter. Följ de lokala reglerna och släng inte dina
gamla produkter i det vanliga hushållsavfallet. Genom att kassera dina gamla produkter på rätt sätt kan du
bidra till att minska eventuella negativa effekter på miljö och hälsa.
Turkish
Eski ürününüzün atılması
Ürününüz, geri dönüşüme tabi tutulabilen ve yeniden kullanılabilen, yüksek kalitede malzeme ve
parçalardan tasarlanmış ve üretilmiştir. Bir ürüne, çarpı işaretli tekerlekli çöp arabası işaretli etiket
yapıştırılması, söz konusu ürünün 2002/96/EC sayılı Avrupa Yönergesi kapsamına alınması anlamına
gelir. Lütfen, elektrikli ve elektronik ürünlerin toplanması ile ilgili bulunduğunuz yerdeki sistem
hakkında bilgi edinin. Lütfen, yerel kurallara uygun hareket edin ve eskiyen ürünlerinizi, normal evsel
atıklarınızla birlikte atmayın. Eskiyen ürününüzün atık işlemlerinin doğru biçimde gerçekleştirilmesi,
çevre ve insan sağlığı üzerinde olumsuz etkilere yol açılmasını önlemeye yardımcı olacaktır.
IFU Approbation / Safety Content
iv
Marantz America, Inc. 100 Corporate Drive Mahwah, NJ07430
RX8001 User Guide
RX8001 User Guide
Printed in Belgium 05/2007 00M40CW851250 mzh-d
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
