Marklyn Group 77091 Bluetooth Starter Kit User Manual
MARKLYN CO. INC. Bluetooth Starter Kit
User Manual
RGB test
77091 {3 RGB<1、2、3>、3 white<4、5、6>}
一、test ways: Bluetooth is powering on.
1, Touch ALPENA RGB starter
2, Bluetooth search interface STASM-12E54B ">"
3, the car interface (check the color to ensure that the lighting color is the same)
4, click on the number 1, 2, 3, enter the Color Selection interface
1) Select the color; check the color to ensure that the lighting color is the same
2) Adjust the brightness of each color, check the light bar is the same
3) Check the Custom selection and check the light bar if changes with touching
4) Way 1: to save the color, click on "Save" and the color wheel, then click on the number
1, 2, 3, 4, 5, 6, check the selected color is saved in the corresponding number box
Way 2: click the number box → Save → wheel color, and checking the number box and
the color of the light is the same.
5, click "Scenes" → "Scenes Selection" interface, and to test the every models, focusing on
"Try me" click, from the red>green > white, but Speed cannot be adjusted.
二 (test for white led “4; 5; 6”)
1 click AlPENA RGB Starter
2 Bluetooth search interface STASM-12E53A “>”
3 In “car” interface observe the color and check whether the emitting color is consistent or
not
4 click the number “4; 5; 6” respectively, and then enter into on/off selection
5 adjust every mode to check whether it is consistent with corresponding led strip
6 see whether the brightness adjustment is right or not
三 test for color groups “1; 2; 3”
1 click the Grouping button and then enter into grouping interface; click number “1; 2/3” and
then finish the grouping; finally, enter into interface “color selection” and check whether the
color of these two grouping strips are consistent with that of adjustment
2 click the number “1; 2; 3” respectively, and then enter into on/off selection
1) Select the color and then observe the color to check whether the emitting color is
consistent or not
2) Adjust the brightness and observe whether the corresponding strips are right or not
3) Adjust custom selection and observe whether the corresponding strips are right or
not
4) Method 1: firstly, click the custom selection respectively and then save the operation;
secondly, click the number “1; 2; 3; 4; 5; 6”, observe whether the selected color is stored in
the corresponding number box
Method2: click the number box and then save the operation; observe the color the
number box is consistent with that of the strip
3, click Scenes → Scenes Selection interface, select each mode, observing whether the two
lights are synchronized at the same time, and adjust its speed, focusing on "Try me"
4, click the Grouping, divide button white into group 4, 5, 6 and test them
① Click on the number 4, 5 / 6 into group, click the ">" button, enter into the "on / off
selection" interface
② Adjust every model respectively to observe whether the corresponding group
operation is consistent and adjust its brightness.
Warning Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.
Reading Light
1, Please click ALPENA internal Kit (Bluetooth is opening)
2, ① Enter into the Bluetooth search interface "Internal Kit” and click ">" to enter into the "Color
Selection" interface
② Click the light bulb to adjust the brightness
③ Adjust each color separately to observe if the operation is consistent with the adjusted color
④ Observe whether the color of the lamp in Custom Selection is consistent with the color
when paddling, and switch on each color separately and adjust the brightness
⑤ To save the color: Please click the number box → save → turntable color to save, and
observe whether the selected color is stored in the corresponding number box
⑥ click Scenes → Scenes Selection interface, to test each model respectively, focusing on
observing "Try me", click Try me from red, green and white , while note that speed cannot be
adjusted
Multiple module grouping tests:
3, click the Grouping button to enter the group selection, click 1,2,3,4 to divide into groups, click
the ">" button after grouping, to enter into the "Color Selection" , and observe whether the color
of multiple module lights is consistent with the color adjustment
4, Click the number 1 or 2 or 3, enter into the Color Selection
1) Choose colors, observe colors, and see if the colors are the same
2) Adjust the brightness of each color; observe whether the led flexible strip is adjusted
uniformly
3) Custom Selection to observe whether light color changes with paddling
4) Method 1: save the color, click "Save", click the color dial, and then click the number "1, 2,
3, 4, 5, 6", observe the selected color is stored in the corresponding number box
Method 2: click on the digital frame - Save - dial color, and observe whether the digital frame
is consistent with the color of the led flexible strip
ALPENA UnderGlowz
1, Click ALPENA UnderGlowz (Bluetooth is on)
2, Enter into Bluetooth search selection, click UGLOWZSM-12E54Z ">."
3, Enter into car selection, observe the color, to ensure that the color of the reflector and the
color of the strip is consistent
4, Click the number 1,2,3,4 respectively to enter the "Color Selection"
①Select the color and then observe the color to check whether the emitting color is consistent or
not
②Adjust the brightness and observe whether the corresponding strips are right or not
③Adjust custom selection and observe whether the corresponding strips are right or not
④To save the color: Please click the number box → save → turntable color to save, and observe
whether the selected color is stored in the corresponding number box
⑤click Scenes → Scenes Selection interface, to test each model respectively, focusing on
observing "Try me", click Try me from red, green and white , while note that speed cannot be
adjusted
5, click the Grouping button to enter the group selection, click 1,2,3,4 to divide into groups, click
the ">" button after grouping, to enter into the "Color Selection" , and observe whether the color
of multiple module lights is consistent with the color adjustment
6、Click the number 1 or 2 or 3, enter into the Color Selection
1) Select the color and then observe the color to check whether the emitting color is
consistent or not
2) Adjust the brightness and observe whether the corresponding strips are right or not
3) Adjust custom selection and observe whether the corresponding strips are right or not
4) Method 1: To save the color: click the custom selection respectively and then save the
operation; secondly, click the number “1; 2; 3; 4; 5; 6”, observe whether the selected color is
stored in the corresponding number box
Method2: Please click the number box → save → turntable color to save, and observe
whether the selected color is stored in the corresponding number box
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two condi
tions: (1) this device may not cause harmful interference, and (2) this device must accept any inte
rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could v
oid the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de
vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec
tion against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructi
ons, may cause harmful interference to radio communications. However, there is no guarantee th
at interference will not occur in a particular installation. If this equipment does cause harmful int
erference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
‐ Reorient or relocate the receiving antenna.
‐ Reorient or relocate the receiving antenna.
‐ Reorient or relocate the receiving antenna.
‐Consult the dealer or an experienced radio/TV technician for help important announcement
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid
and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AMN
5-77091 ".
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as show
in this manual.