Marquardt ME1 Gateway User Manual 2016 12 07 MM1 ME1
Marquardt GmbH Gateway 2016 12 07 MM1 ME1
UserManual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3221716 |
| Application ID | 2sF10QHTYyUWk49GdNO/dQ== |
| Document Description | UserManual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 12.49kB (156110 bits) |
| Date Submitted | 2016-12-08 00:00:00 |
| Date Available | 2016-12-08 00:00:00 |
| Creation Date | 2016-12-07 14:02:26 |
| Producing Software | GPL Ghostscript 9.06 |
| Document Lastmod | 2016-12-07 14:02:26 |
| Document Title | 2016-12-07_MM1_ME1_User Manual |
| Document Creator | PDFCreator Version 1.6.0 |
| Document Author: | SiegelG |
MM1 / ME1 User Manual Introduction Azor is a wireless communications system that can be mounted on a vehicle. Azor allows remote operation of integrated components located on the same machinery. The system consists of 1 gateway ME1 and 2 fobs MM1. The gateway connects to the CAN bus on the machinery. It is advantageous if the machinery includes a user interface to program settings on the gateway. The fobs communicate to a Blue Tooth radio with integrated antenna inside the gateway. Individual buttons send uniquely numbered messages onto the CAN Bus. New fobs can be paired with the system in the field. MM1 ME1 Figure 1 Azor System Components W:\CEQ_Bereich\Funkzulassungen\Projekte\John Deere_Azor_M209301\03 Allgemeine Produktbeschreibung\2016-1207_MM1_ME1_User Manual.docx Seite 1 von 3 MM1 / ME1 User Manual Installation Carefully remove the components from the box. Use M6 Button head screws to mount the gateway onto the machine. Connect the 8-pin Deutch connector to the gateway. Be sure that the lines are unpowered while making the connection. Pin 1 is top left and pin 8 is bottom left in Figure 2 Gateway Connector. Figure 2 Gateway Connector Figure 3 Deutch Connector Pin Designations Be sure to mount the gateway in a location that does not interfere with the Blue Tooth wireless communications. Metal should not be located between the internal antenna and locations where the operator will be pressing the fob buttons. (If the fob operator cannot see the gateway, the fob reception will be reduced.) Setup The gateway initially is accompanied by 2 fobs that are paired with the gateway. Power can be supplied to the gateway from the vehicle through either the ELX pin or the Vbat Pin, or both. There are multiple operating modes of the system, depending on the pins providing power and a few parameters. Conditions for Modes of Operation ELX Power When the gateway power source is through the ELX pin, without Vbat present, the entire module is configured to operate continuously in the normal mode. No software modifications are required. W:\CEQ_Bereich\Funkzulassungen\Projekte\John Deere_Azor_M209301\03 Allgemeine Produktbeschreibung\2016-1207_MM1_ME1_User Manual.docx Seite 2 von 3 MM1 / ME1 User Manual Vbat Power Without Wake_Enable Bit Set The gateway is set up to operate when there is power on both the Vbat pin and the ELX pin. If ELX is removed, the gateway enters a low power sleep mode. The gateway draws the least amount of current in this mode. Neither Blue Tooth nor CAN communications are available. From a configuration setting, this means that the Wake_Enable bit has not been set by a command from the vehicle user interface. The only way to put the gateway into the operational state is to put power on the ELX pin. Vbat Power with Wake_Enable Bit Set The gateway can be configured to a low power mode called standby. Standby mode is entered when the gateway has an internal bit set called Wake_Enable, and there is no power on the ELX pin. In this mode, the gateway CAN communications are not operational, but the Blue Tooth communications are operational. From standby mode, the system can transition to operational mode upon the reception of a predesignated fob button press. Upon the reception of the message from the fob, the gateway will enter the operational mode for an amount of time. After this time has lapsed, the gateway will reenter the standby mode, unless the ELX signal returns beforehand. The length of time that the gateway will stay in operational mode, waiting for the ELX signal is programmable through the use interface. Fob Pairing The fobs that come with the gateway have been pre-paired at the factory. The ID numbers for these fobs will appear in the “white list” in the user interface. Other fobs can also be paired in the field by following these steps. 1) In the user interface, enter the 9 underlined digits in the fob serial number. 2) Upon entering these digits, press a fob button on the new fob. a. Be sure that you are within the reception range of the gateway. b. Push the fob button within 2 minutes of entering the ID number. 3) The new number should then show up in the permanent “white list” in the user interface. 4) If the number does not show up in the white list, the pairing was not successful. Other Blue Tooth Certified devices may be paired with the gateway. Contact your local distributor for details. Field Service There are no field serviceable parts on the gateway. The fob may require a new battery on occasion. To replace the battery on the fob, carefully separate the 2 covers. Use a coin or other blunt edge to pry the covers apart. Carefully remove the battery, without removing the small metal battery contact. Place the new battery into the cover. Firmly snap the 2 covers back together. 07.12.2016 SGE W:\CEQ_Bereich\Funkzulassungen\Projekte\John Deere_Azor_M209301\03 Allgemeine Produktbeschreibung\2016-1207_MM1_ME1_User Manual.docx Seite 3 von 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 3 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:e68df795-bed8-11e6-0000-99cbbc3298cf Producer : GPL Ghostscript 9.06 Keywords : () Modify Date : 2016:12:07 14:02:26+01:00 Create Date : 2016:12:07 14:02:26+01:00 Creator Tool : PDFCreator Version 1.6.0 Document ID : uuid:e68df795-bed8-11e6-0000-99cbbc3298cf Format : application/pdf Title : 2016-12-07_MM1_ME1_User Manual Creator : SiegelG Description : () Author : SiegelG Subject :EXIF Metadata provided by EXIF.tools