Martec Access MK-5050 Garage Door Opener User Manual Manual Excerpt
Martec Access Products Inc Garage Door Opener Manual Excerpt
Manual Excerpt
GEM RF CONTROLLER SYSTEM SPECIFICATIONS 1. Supply Voltage: 3. Relay Contact Load 24VAC/DC Rating: 1 AMP @ 24VAC/DC 2. Frequency: 303 MHz 4. Transmitter powered by 9 Volt battery. DESCRIPTION The Gem two‘channel RF controller system is designed for use with an operator controller that is provided with a “Constant Pressure” mode of operation. The motor will run in the direction selected by the activated push-button until the push-button is released. When the push-button is released the motor shall stop. CONSTANT PRESSURE FUNCTION Depressing a directional pnshbutton will cause the appropriate RF controller relay to energize the operator directional relay to run the motor in the selected direction. The motor will run in the selected direction for the duration of the pushbutton closure. The motor will stop when the pushbutton is released, or the end of travel limit switch in the selected direction is actuated. !! WARNING !! DISCONNECT POWER TO THE OPERATOR BEFORE INSTALLING THE RECEIVER. PAGE ONE RECEIVER BOARD INSTALLATION PART #SP-5002-GEM The receiver board is provided with a 24” long color-coded harness for interconnection of the receiver board with the motor control board of the operator. 1. Black Wire: 24 VAC/DC Positive power supply connection and common to the control relays. 1. White Wire: l4VAC/DC Negative power supply connection. 3. Red Wire: Normally open Relay output to Down direction. 4. Yellow Wire: Normally open Relay output to Up direction. 5. Blue Wire: Two Blue wires for connection to Learn Button. 6. Red “Learn” LED on receiver board. at Turns on when “Learn” button is depressed. b. Turns of! when new transmitter code is programmed into the system. c. Times out if transmitter is not prograrmned within 30 seconds. 7. “Clear" push-button mounted on receiver board erases transmitter memory. NOTE: Move jumper J-5 to location J-4 to change relay common from DC Positive to DC Negative when required. RECONNECT POWER TO OPERATOR AND PROGRAM TRANSMITTER TRANSMITTER 2 BUTTON PART # SP—SZZO-GEM Program the transmitter into the receiver board. I. Depress customer supplied “Learn“ push-button. The red LED on the receiver board will light. is. Depress any of the two buttons on the transmitter. The red LED on the receiver board will go out when the new code is installed in the receiver board. c. Test operator for proper Up and Down response from the operator to the RC commands. T he end of travel limits must be properly adjusted before this test is run. ”WARNING” DO NOT ALLOW CHILDREN TO PLAY WITH OR OPERATE REMOTE CONTROL TRANSMITTERS. The hoist could operate and cause serious injury or death. THIS DEVICE COMPLIES WITH FCCRULES PART 15 AND IC CANADA RULES AND RE GULA TIONS. OPERA TION OF THIS DE VICE IS SUBJECT TO THE F OLLO WING CONDITIONS: ( I ) THIS DE VICE MA YNOT CA USE HARMFUL INTERFERENCE; (2) THE DEVICE MUSTACCEPTANYINTERFERENCE THA TMA YBE RECEIVED, INCLUDING INTERFERENCE T HA T MA Y CA USE UNDESIRED OPERA TION; (3) CHANGES 0k MODIFICA TIONS N0 T EXPRESSL Y APPRO VED B Y THE MAN UFA C TURER COULD VOID THE A U THOR! TY OF USERS T0 OPERA TE THIS EQUIPMENT. PAGE TWO
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2001:04:05 09:01:05-05:00 Create Date : 2001:04:05 09:00:52-05:00 Creator : Acrobat 4.0 Scan Plug-in for Windows Producer : Acrobat 4.0 Scan Plug-in for Windows Page Count : 2EXIF Metadata provided by EXIF.tools